SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Design Characteristics of a cryopump optimized for xenon are presented. The cost and complexity of installing and operating these cryopumps is a fraction of the cost and complexity to install and operate diffusions pumps or cryopumps that deliver similar pump speeds on xenon.
Higher dimensional flamelet manifolds are essential in capturing the coupled effects of pressure gradients and unsteady chemical kinetics observed in supersonic combustion applications. Previous studies have validated the feasibility of using deep neural networks as an alternative to computation-ally intensive multidimensional flamelet table storage and lookup. This approach has demonstrated a significant reduction in memory footprint and enabled the use of larger dimensional tabulated manifolds for supersonic combustion in canonical problems. In this study, the Unsteady Flamelet Progress Variable (UFPV)-ANN model implemented in the VULCAN-CFD code is validated by the Burrows-Kurkov supersonic mixing/combustion configuration. The well characterized experimental problem consists of hydrogen injection into a supersonic vitiated crossflow that results in a lifted flame structure. The initial model consists of a 4-dimensional table where the independent variables Z, C, Xst, P are tabulated using an unsteady flamelet code with boundary conditions corresponding to the vitiated air conditions. The results show the development of a lifted flame structure and over-all acceptable agreement with finite-rate chemistry (FRC) simulation and the experimental data. Moreover, direct mapping between the independent variables and the flamelet table is replaced by a deep neural network for significant memory reduction. The results indicate that the UFPV-ANN approach can retrieve the same solution as the memory intensive lookup table approach.
Introduction: All In-Situ Resource Utilization (ISRU) regolith reactor systems that aim to extract gases or vapors must maintain a seal along the flow path of the regolith from the inlet hopper to where extracted gases or vapors are generated. Using a column of regolith at the inlet has been proposed as an alternative to systems using series of mechanical valves to reduce mass and complexity. Preliminary investigations into the use of regolith itself as a barrier to escaping fluids have been conducted, which this research seeks to expand upon. Different vertical regolith simulant plug diameters and heights were tested under vacuum with dry nitrogen to observe leak rates and approximate steady state pressure gradient equilibria. The effect of absolute ambient pressure was also studied by repeating tests at incremental pressures ranging from 10e-5 Torr up to 1 atm to corroborate ambient bench tests from previous work. The impact of regolith dynamics was addressed to emulate continuous-feed regolith reaction processes by measuring leak rates through continuously draining simulant columns. OB-1 lunar highlands regolith simulant was used. Experimental Setup: Regolith simulant columns were constructed using a motorized butterfly valve separating upper acrylic tubes of various diameters from a larger, lower aluminum pipe plenum (See Figure 1). The butterfly valve was cracked open such that gas could freely pass through whereas regolith would bridge and stay suspended as a cohesive plug above in the acrylic portion. These assemblies were loaded into a vacuum chamber, and a compressed dry nitrogen line was routed into the lower plenum. Pressure transducers measured the absolute pressure of the lower plenum, which was compared to absolute chamber pressure to monitor the pressure gradient across the regolith simulant. A precision mass flow controller enabled fine control of plenum pressure. The plenum pressure was quasi-statically increased to set points informed by previous work [1] before shutting off the gas supply to allow the now pressurized gas volume to dissipate through the simulant into the chamber in what was referred to as a ‘leak test.’ In a separate set of tests, the pressure was allowed to quasi-statically build until visual disturbances in the soil were observed via remote camera feeds. Initial leak rate tests were repeated on the disturbed soil to observe changes in leak rates between initial as-poured and post-bubbling soil conditions. This test schedule was applied to simulant columns of three different diameters (approximately 2, 4, and 6 inches) as well as two different heights (around 8 and 16 inches) and was repeated at least three times for each configuration. Plenums were also pressurized while the butterfly valves were opened slightly further to facilitate slow, controlled, constant flowrate draining of the simulant to observe the impact that continuous-feed systems might have on leak rate through the regolith column. Finally, the regolith columns were reset and refilled and static leak rate tests were repeated approximately every decade in ambient pressure from 10e-5 Torr up to ambient conditions to observe the impact of transitioning out of the molecular flow regime on regolith column seal performance. Analysis: Trends with respect to each factor examined were constructed and reported alongside commentary on the most likely responsible physical phenomena. Confidence intervals were applied to the predictive findings of the data by quantifying instrumentation error and accounting for probabilistic impacts of curve fitting the generic exponential function onto pressure decay data. The leak rate is assumed directly proportional to the exponential term coefficient, while the steady-state static pressure gradient is assumed to be the asymptotic limit of each curve fit. Finally, a generic model developed by Ogino et al. [2] and later tuned for ambient testing was re-tuned using vacuum data to estimate leak rates on the lunar surface. Results: Pressure decay rates decreased up to 27-fold under vacuum when compared to ambient pressure, as shown in Figure 2. Simulant column diameter was found to exponentially correlate to both regolith column leak rate and steady-state equilibrium pressure delta. Height was found to be linearly related to leak rate –doubling the regolith column height consistently yielded around a 40% reduction in leak rate. Dynamic regolith draining was found to slightly increase leak rate, although to a lower degree than expected. Conclusion: Because of the transition into molecular gas flow through regolith, vacuum testing is required to properly estimate performance. Regolith columns should be designed as narrow as possible to avoid bridging and minimize leak rate, and as tall as is feasible to both further reduce leak rate and to help prevent bubbling, which has been shown to degrade the quality of the regolith seal. Disrupted soil was found to exhibit higher leak rates than pristine, as-poured soil, indicating the need to consider the impact of recovery from depressurization events. Regolith columns appear equally feasible for both dosed and continuous-feed reactors.
Filtered Rayleigh scattering (FRS) is a diagnostic technique used for measurements of macroscopic properties of a gas. The FRS signal is passed through a narrow bandwidth molecular filter, commonly gaseous iodine, to measure the broadening and Doppler-shift of the scattering light from the molecules of the gas flow. However, in single-frequency, intensity-based approaches, the effects of pressure, temperature, and velocity can be difficult to deconvolve. To overcome this challenge, frequency-scanning FRS has been used to quasi-spectrally resolve the signal. In this work, a frequency-scanned, burst-mode laser was used to perform scanning FRS in an underexpanded jet to measure temperature, pressure, and radial velocity at measurement rates up to 1 kHz which is ~100,000 times faster than prior implementations of scanning FRS.
Explore the source record for details and available documents.
As part of the design optimization and model validation effort within the hybrid energy systems program, the research to implement dynamical system scaling (DSS) code to RAVEN is funded under the Integrated Energy System program in collaboration with the Digital Reactor Technology & Development department. The DSS data processing algorithm has been coded within the RAVEN framework along with other metrics and postprocessing models. The implemented code was tested using a gravity-driven draining tank draining case modeled in RELAP5-3D and generated data was successfully postprocessed based on the scaling analyses defined by DSS. Postprocessed data concluded less agreement for the tank exit velocity and indicated that the modeled input deck for RELAP5-3D requires modification to enforce minimal pressure differential effects to the draining process.
The disposition of sodium-bonded spent nuclear fuel and blanket materials in a repository is complicated by the presence of sodium metal that is used as a thermal bond between the uranium metal fuel and blanket slugs and their cladding. The concern is that the metallic sodium could react with water, producing explosive hydrogen gas, or could exhibit a pyrophoric character. Thus, experimental studies were performed to investigate and demonstrate the removal and deactivation of bond sodium from blanket material in a dry environment. Specifically, bond sodium was removed from unirradiated Fermi-1 blanket elements and an assembly via a melt-drain-evaporate process using elevated temperature and reduced pressure. The effectiveness of sodium metal removal from the blanket materials and their associated cladding was =99.9998%, based on post-test quantitative analyses. The separated sodium metal was collected and subsequently deactivated by reacting it in a molten state with a controlled addition of ammonium chloride particles atop a molten salt medium. In this process sodium chloride is formed and assimilates into the salt pool. The subsequent deactivation of the bond sodium produced a solid ingot of sodium chloride, potassium chloride, lithium chloride, and cesium chloride that was devoid of sodium metal based on post-test analyses of the salt product. Both the sodium removal and deactivation operations were conducted within a dry inert atmosphere enclosure. The results of this study substantiate a path forward for the disposition of sodium-bonded blanket materials, including 34 metric tons heavy metal in irradiated Fermi-1 blanket material currently stored at Idaho National Laboratory.
Some measurements of the effects of rocket-motor operation on base pressure were obtained incidental to other research on some bodies in free flight. These data are presented and qualitatively analyzed. The analysis indicates that jet effects on drag are of sufficient importance to deserve consideration in the design of jet motor nozzles, especially for aircraft and missiles where the thrust and drag are of the same order of magnitude. The base-pressure changes induced by the jet should be considered in the structural design of the outer body skin on the aft portion of fuselages containing jets. (author)
As part of the NASA Energy Efficient Engine program, scale-model performance tests of a mixed flow exhaust system were conducted. The tests were used to evaluate the performance of exhaust system mixers for high-bypass, mixed-flow turbofan engines. The tests indicated that: (1) mixer penetration has the most significant affect on both mixing effectiveness and mixer pressure loss; (2) mixing/tailpipe length improves mixing effectiveness; (3) gap reduction between the mixer and centerbody increases high mixing effectiveness; (4) mixer cross-sectional shape influences mixing effectiveness; (5) lobe number affects mixing degree; and (6) mixer aerodynamic pressure losses are a function of secondary flows inherent to the lobed mixer concept.
Materials selection is a key concern for corrosion resistance in elevated temperature and pressure direct-fired supercritical CO2 (sCO2) power cycles. The effect of elevated pressure on corrosion resistance can be critical, as impurities within the supercritical fluid such as H2O and O2 can have additional corrosion effects than found at ambient pressure conditions. Several wrought nickel-based commercial alloys (230, 263, 282, 617, 625, 740H) were exposed to direct-fired conditions (95CO2 – 4H2O – 1 O2) at 750 °C at both atmospheric pressure (0.1 MPa) and supercritical conditions (20 MPa) for over 2,000 h. Additionally, additive manufactured (AM) 282 produced by laser powder bed fusion (LPBF) were also included in the exposures. Supercritical conditions affected the oxidation behavior of several alloys. Most notably, water-vapor assisted Cr-oxide volatilization was observed at 750 °C supercritical conditions. Many alloys did not form sufficient protective Cr-oxide scales at supercritical conditions, leading to increased oxidation at elevated pressure. Differences in oxidation behavior were also observed for 282 AM samples compared to their wrought counterparts, with the differences also dependent on the LPBF build parameters and post-production treatments (heat treatment and surface finishing procedures). The AM samples formed Mo-rich carbides in the alloy beneath the oxide following sCO2 exposure, implying potentially higher levels of carbon uptake relative to the wrought
The measured effects of a circumferential distortion in inlet total pressure on the fan, low, and high compressor of an afterburning turbofan engine are presented and discussed. Extensive inner-stage instrumentation, combined with a unique test technique offered an accurate means of measuring the shifts in flow, performance, and stall mechanisms within the compressor. These effects are compared at one speed to the corresponding effects measured with undistorted inlet flow. The results show the rate at which the distorted flow areas were attenuated and rotated as well as the change in flow velocities that occurred at various points in the compressor. High response pressure traces indicated the location of stalls including the sequence of dynamic events from the onset and propagation of various stall-recovery events, to compressor surge, to the resulting hammershock.
The measured effects of a circumferential distortion in inlet total pressure on the fan, low, and high compressor of an afterburning turbofan engine are presented and discussed. Extensive inner-stage instrumentation, combined with a unique test technique offered an accurate means of measuring the shifts in flow, performance, and stall mechanisms within the compressor. These effects are compared at one speed to the corresponding effects measured with undistorted inlet flow. The results show the rate at which the distorted flow areas were attenuated and rotated, as well as the change in flow velocities that occurred at various points in the compressor. High response pressure traces indicated the location of stalls including the sequence of dynamic events from the onset and propagation of various stall-recovery events, to compressor surge, to the resulting hammershock.
The effects of spanwise blowing on the surface pressures of a 44 deg swept trapezoidal wing-strake configuration were measured. Wind tunnel data were obtained at a free stream Mach number of 0.26 for a range of model angle of attack, jet thrust coefficient, and nozzle chordwise location. Results showed that spanwise blowing delayed the leading edge vortex breakdown to larger span distances and increased the lifting pressures. Vortex lift was achieved at span stations immediately outboard of the strake-wing junction with no blowing, but spanwise blowing was necessary to achieve vortex lift at increased span distances. Blowing on the wing in the presence of the strake was not as effective as blowing on the wing alone. Spanwise blowing increased lift throughout the angle-of-attack range, improved the drag polars, and extended the linear pitching moment to higher values of lift. The leading edge suction analogy can be used to estimate the effects of spanwise blowing on the aerodynamic characteristics.
Here, with intricate lattice structures, kagome materials are an excellent platform to study various fascinating topological quantum states. In particular, kagome materials, revealing large responses to external stimuli such as pressure or magnetic field, are subject to special investigation. Here we study the kagome-net HoMn 6 Sn 6 magnet that undergoes paramagnetic to ferrimagnetic transition (below 376 K) and reveals spin-reorientation transition below 200 K. In this compound, we observe the topological Hall effect and substantial contribution of anomalous Hall effect above 100 K. We unveil the pressure effects on magnetic ordering at a low magnetic field from the pressure tunable magnetization measurement. By utilizing high-resolution angle-resolved photoemission spectroscopy, Dirac-like dispersion at the high-symmetry point K is revealed in the vicinity of the Fermi level, which is well supported by the first-principles calculations. Our investigation will pave the way to understanding the magnetotransport and electronic properties of various rare-earth-based kagome magnets.
Boundary layer study to determine effect of positive pressure gradient on transition from laminar to turbulent flow
Analog computer simulation of design parameter effects on stability of direct acting gas pressure regulator based on Brayton cycle space power generator
The effects of N2 pressure (0.1 to 50 MPa) during sintering on the thickness of the microstructurally heterogeneous layer (MHL) formed near the surface of the compact, transverse-rupture strength, were investigated for Si3N4-(10 to 20) mol % MgO-5.5 mol % Al2O3 ceramics. The sintering temperature and time were 1973 K and 3.6 ks, respectively. The N2 gas was introduced into the furnace at about 1273 K. When the compacts were sintered under a certain N2 pressure, for example, about 20 and 7 MPa for 10 and 15 mol% MgO, respectively, the evolutions of N and Si were suppressed. The thickness of the MHL became very small and at the same time the strength of the surface layer of the compact (which was normally less than that of the inside in the case of 0.1 MPa) became nearly the same value as that of the inside. At higher pressure, the strength of both surface layer and the inside decreased considerably. Some discussion was made on these results.
An experimental investigation was made to determine the effects of screen-induced total-pressure distortions on two J85-GE-13 turbojet engines. Results were compared to those from a previous program run with a third engine. All compressors were found to be sensitive to a critical angle of circumferential distortion equal to 60 deg., and they all adhered closely to the parallel compressor model. The sensitivity of compressor exit pressure to virtually any type of distortion pattern can be determined by defining stall lines for undistorted, hub radial distorted, and tip radial distorted inflows. The effect of multiple sectors of circumferential distortion is defined.