The effect of vent burst pressure on a vented hydrogen–air deflagration in a 1 m3 vessel
Not Available
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
Elastomers are known to gain enhanced mechanical properties through compounding with nanosized filler particles such as silica or carbon black. Filler dispersion and filler-polymer interfacial strength are key contributing factors to this improvement. The interfacial strength is critical to part lifetime in pressurized gas sealing applications such as O-rings, where weak binding between the filler particle and polymer matrix can lead to internal void structures. With the aim to build a fundamental understanding of precursors to pressurized hydrogen-induced failure in elastomers, we use all-atom molecular dynamics simulations to study the impact of hydrogen oversaturation on filler-polymer interaction strength. We systematically study the interface between a commonly used elastomer, ethylene-propylene-diene monomer (EPDM) and silica by varying gas concentration, crosslink density, and surface chemistry. Our simulations predict that decompression leads to a localization of excess gas near the interface. In conclusion, we demonstrate that this localized gas can weaken interfacial adhesion and quantify the interaction using thermodynamic approaches.
Not Available
A button solid oxide fuel cell with a La0.6Sr0.4Co0.2Fe0.8O3 cathode and a nickel-YSZ anode was tested over a range of temperatures from 650 to 800°C and a range of pressures from 101 to 724 kPa. The fuel was simulated steam-reformed kerosene and the oxidant was air. The observed increases in open circuit voltages (OCV) were accurately predicted by the Nernst equation. Kinetics also increased, although the power boost due to kinetics was about two thirds as large as the boost due to OCV. The total power boost in going from 101 to 724 kPa at 750°C and 0.8 volts was 66%. Impedance spectroscopy demonstrated a significant decrease in electrodic losses at elevated pressures. Complex impedance spectra were dominated by a combination of low frequency processes that decreased markedly with increasing pressure. A composite of high-frequency processes also decreased with pressure, but to a lesser extent. An empirical algorithm that accurately predicts the increased fuel cell performance at elevated pressures was developed for our results and was also suitable for some, but not all, data reported in the literature.
An investigation into the structural stability, electronic and elastic properties of Ti{sub 3}GeC{sub 2} under high hydrostatic pressure was conducted using first-principles calculations based on density functional theory (DFT). From the energy and enthalpy calculations, and the variations of elastic constants with pressure, we conclude that {alpha}-Ti{sub 3}GeC{sub 2} is most stable upon compression to 100 GPa, which is not consistent with the nonhydrostatic in situ synchrotron X-ray diffraction studies. The higher structural stability was analyzed in terms of electronic level. The absence of band gap at the Fermi level and the finite value of the density of states at the Fermi energy reveal the metallic behavior of all polymorphs of Ti{sub 3}GeC{sub 2}. -- Graphical abstract: The less phase stability of {beta}-Ti{sub 3} SiC{sub 2} compared to that of {alpha}-Ti{sub 3} SiC{sub 2} can be interpreted by the states between -6.0 and 3.6 eV shift toward the higher energy region for {beta}-Ti{sub 3} SiC{sub 2} Display Omitted Research highlights: > From the energy and enthalpy calculations of polymorphs for Ti{sub 3}GeC{sub 2}, we can conclude that Ti{sub 3}GeC{sub 2} possessed higher stable structural stability under pressure to 100 GPa, which is not consistent with the nonhydrostatic experiments. > The higher stable structure of Ti{sub 3}GeC{sub 2} is testified by the calculated variations of elastic constants with pressure. > The reasons for this higher stable phase stability were discussed in terms of the electronic level.
Graphical abstract: - Highlights: • Microstructural and optical properties are studied systematically. • The optical properties are studied by UV–visible and photoluminescence. • The PL spectra shows two peaks correspond to bandgap of anatase and rutile. • The maximum refractive index of 2.73 is obtained for rutile phase of titania. - Abstract: Nanocrystalline titanium oxide (TiO{sub 2}) thin films were deposited on silicon (1 0 0) and quartz substrates at various oxygen partial pressures (1 × 10{sup −5} to 3.5 × 10{sup −1} mbar) with a substrate temperature of 973 K by pulsed laser deposition. The microstructural and optical properties were characterized using Grazing incidence X-ray diffraction, atomic force microscopy, UV–visible spectroscopy and photoluminescence. The X-ray diffraction studies indicated the formation of mixed phases (anatase and rutile) at higher oxygen partial pressures (3.5 × 10{sup −2} to 3.5 × 10{sup −1} mbar) and strong rutile phase at lower oxygen partial pressures (1 × 10{sup −5} to 3.5 × 10{sup −3} mbar). The atomic force microscopy studies showed the dense and uniform distribution of nanocrystallites. The root mean square surface roughness of the films increased with increasing oxygen partial pressures. The UV–visible studies showed that the bandgap of the films increased from 3.20 eV to 3.60 eV with the increase of oxygen partial pressures. The refractive index was found to decrease from 2.73 to 2.06 (at 550 nm) as the oxygen partial pressure increased from 1.5 × 10{sup −4} mbar to 3.5 × 10{sup −1} mbar. The photoluminescence peaks were fitted to Gaussian function and the bandgap was found to be in the range ∼3.28–3.40 eV for anatase and 2.98–3.13 eV for rutile phases with increasing oxygen partial pressure from 1 × 10{sup −5} to 3.5 × 10{sup −1} mbar.
Here this study investigates the impact of pressure and dilution on combustion behavior of of C 2H6/air/N2 mixtures within an externally heated micro-tube using both experimental and analytical techniques. Experiments are conducted for pressures up to 10 bar at multiple dilution levels and document three flame regimes, i.e. weak flames, FREI and normal flames. Characteristic temperatures for flame stabilization, as well as and ignition and extinction are obtained by applying a novel thin filament pyrometry method (TFP), which uses a thin silicon carbide (SiC) filament that enables temperature measurements for both reacting and non-reacting cases. Results show a decrease of characteristic temperatures with increasing pressure, which can be which can be partially compensated by a decrease of O2 content. Further, regime transitions occur at lower velocity as the pressure increases, whereas weak flame positions are insensitive to dilution at a given pressure. Predictions from the analytical model compare favorably with experimental results. The most prominent finding is that as dilution increases, the transition from weak flame to FREI becomes less abrupt and is completely lost for high dilution levels (i.e. low O2 content). Both experimental and analytical results indicate that the unstable FREI combustion regime does not exist at high dilution levels, i.e. weak flame and normal flame regimes are no longer clearly separated. As FREI are interpreted as a cyclic transition from an ignition zone to a propagating flame, results for highly diluted conditions are interpreted as a combustion regime where classical flame propagation ceases to exist.
Not Available
Abstract not provided
Lately, the atmospheric pressure jet type corona plasma, which has been typically driven by dc to low frequency (LF: several tens of kHz), is often generated by using radio frequency of 13.56 MHz. Yet, the relationship between the plasma and its driving frequency has seldom been investigated. Hence, in this study, dependence of the atmospheric pressure corona plasma characteristics on the driving frequency was explored experimentally from LF to rf (5 kHz-13.56 MHz). The plasmas generated by the driving frequency under 2 MHz were cylindrical shape of several tens of millimeters long while the 13.56 MHz plasma is spherical and a few millimeters long. As the driving frequency was increased, the plasma length became shortened. At the lower driving frequencies (below 2 MHz), the plasmas existed as positive streamer and negative glow for each half period of the applied voltage, but the discharge was more continuous in time for the 13.56 MHz plasma. It was inferred from the measured I-V curves that the higher driving frequency induced higher discharge currents, and the gas temperature was increased as the driving frequency was increased.
We study the shock wave structure in a rarefied polyatomic gas based on a simplified model of extended thermodynamics in which the dissipation is due only to the dynamic pressure. In this case the differential system is very simple because it is a variant of Euler system with a new scalar equation for the dynamic pressure [T. Arima, S. Taniguchi, T. Ruggeri, and M. Sugiyama, Phys. Lett. A 376, 2799–2803 (2012)]. It is shown that this theory is able to describe the three types of the shock wave structure observed in experiments: the nearly symmetric shock wave structure (Type A, small Mach number), the asymmetric structure (Type B, moderate Mach number), and the structure composed of thin and thick layers (Type C, large Mach number)
In this study, pressures of ∼5 to ∼8 MPa were applied to organic light emitting diodes containing either evaporated molybdenum trioxide (MoO{sub 3}) or spin-coated poly(3,4-ethylene dioxythiophene) doped with poly(styrene sulphonate) (PEDOT:PSS) hole-injection layers (HILs). The threshold voltages for both devices were reduced by about half, after the application of pressure. Furthermore, in an effort to understand the effects of pressure treatment, finite element simulations were used to study the evolution of surface contact between the HIL and emissive layer (EML) under pressure. The blister area due to interfacial impurities was also calculated. This was shown to reduce by about half, when the applied pressures were between ∼5 and 8 MPa. The finite element simulations used Young's modulus measurements of MoO{sub 3} that were measured using the nanoindentation technique. They also incorporated measurements of the adhesion energy between the HIL and EML (measured by force microscopy during atomic force microscopy). Within a fracture mechanics framework, the implications of the results are then discussed for the pressure-assisted fabrication of robust organic electronic devices.
Ex-situ spectroscopic ellipsometry measurements are made on radio frequency magnetron sputtered oxygenated cadmium sulfide (CdS:O) thin films. Films are deposited onto glass substrates at room temperature and at 270 °C with varying oxygen to total gas flow ratios in the sputtering ambient. Ellipsometric spectra from 0.74 to 5.89 eV are collected before and after annealing at 607 °C to simulate the thermal processes during close-space sublimation of overlying cadmium telluride in that solar cell configuration. Complex dielectric function (ε = ε{sub 1} + iε{sub 2}) spectra are extracted for films as a function of oxygen gas flow ratio, deposition temperature, and post-deposition annealing using a parametric model accounting for critical point transitions and an Urbach tail for sub-band gap absorption. The results suggest an inverse relationship between degree of crystallinity and oxygen gas flow ratio, whereas annealing is shown to increase crystallinity in all samples. Direct band gap energies are determined from the parametric modeling of ε and linear extrapolations of the square of the absorption coefficient. As-deposited samples feature a range of band gap energies whereas annealing is shown to result in gap energies ranging only from 2.40 to 2.45 eV, which is close to typical band gaps for pure cadmium sulfide.
Abstract not provided