Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

An Experimental Investigation of the Flow Physics Associated With End Wall Losses and Large Rotor Tip Clearances as Found in the Rear Stages of a High Pressure Compressor

The focus of this work was to characterize the fundamental flow physics and the overall performance effects due to increased rotor tip clearance heights in axial compressors. Data have been collected in the three-stage axial research compressor at Purdue University with a specific focus on analyzing the multistage effects resulting from the tip leakage flow. Three separate rotor tip clearance heights were studied with nominal tip clearance heights of 1.5%, 3.0%, and 4.0% based on a constant annulus height. Overall compressor performance was investigated at four corrected speedlines (100%, 90%, 80%, and 68%) for each of the three tip clearance configurations using total pressure and total temperature rakes distributed throughout the compressor. The results have confirmed results from previous authors showing a decrease of total pressure rise, isentropic efficiency, and stall margin which is approximately linear with increasing tip clearance height. The stall inception mechanisms have also been evaluated at the same corrected speeds for each of the tip clearance configurations. Detailed flow field measurements have been collected at two loading conditions, nominal loading (NL) and high loading (HL), on the 100% corrected speedline for the smallest and largest tip clearance heights (1.5% and 4.0%). Steady detailed radial traverses of total pressure at the exit of each stator row have been supported by flow visualization techniques to identify regions of flow recirculation and separation. Furthermore, detailed radial traverses of time-resolved total pressures at the exit of each rotor row have been measured with a fast-response pressure probe. These data have helped to quantify the size of the leakage flow at the exit of each rotor. Thermal anemometry has also been implemented to evaluate the time-resolved three-dimensional components of velocity throughout the compressor and calculate blockage due to the rotor tip leakage flow throughout the compressor. These measurements have also been used to calculate streamwise vorticity. Time-resolved static pressure measurements have been collected over the rotor tips for all rotors with each of the three tip clearance configurations for up to five loading conditions along the 100% corrected speedline using fast-response piezoresistive pressure sensors. These time-resolved static pressure measurements, as well as the time-resolved total pressures and velocities have helped to reveal a profound influence of the upstream stator vane on the size and shape of the rotor tip leakage flow. Finally, a novel particle image velocimetry (PIV) technique has been developed as a proof-of- concept. In contrast to PIV methods that have been typically been utilized for turbomachinery applications in the past, the method used for this study introduced the laser light through the same access window that was also used to image the flow. This new method addresses potential concerns related to the intrusive laser-introducing techniques that have typically been utilized by other authors in the past. Ultimately, the data collected for this project represent a unique data set which contributes to build a better understanding of the tip leakage flow field and its associated loss mechanisms. These data will facilitate future engine design goals leading to small blade heights in the rear stages of high pressure compressors and aid in the development of new blade designs which are desensitized to the performance penalties attributed to rotor tip leakage flows.

Berdanier, Reid A.↗

Development of A Maximum Anti-Slosh Baffle Pressure Load Model

The sloshing of propellants can affect the stability of a spacecraft and the integrity of the tank structure. Undesirable sloshing can be controlled by the addition of anti-slosh baffles, and the spacing and configuration of baffles are driven by damping requirements. The structural design of the baffle is determined after consideration of many factors, such as the strength and rigidity needed to support the baffle for its lifetime. Therefore, knowledge of distributed pressure loading is important for detailed structural design. In addition, the resultant force and moment produced by the distributed pressure are of direct importance to the design of a vehicle’s control system. Previous experimental investigations have been conducted to determine the liquid pressure loads and slosh damping associated with a rigid ring baffle. The results suggested that when the nondimensional velocity parameter is larger than 1.0, the theories agree with the test. However, when the velocity parameter is less than 1.0, all theories are nonconservative and under-predict the pressure loads. The present study has derived a maximum pressure load on the slosh baffle based on the energy conservation principle. It is verified from CFD that pressure in the slosh flow field can be decomposed into static and transient components. The CFD results confirm that there is a phase shift in pressure across the baffle, which depends on the fluid damping. Higher damping leads to a higher phase shift. The CFD investigation further verifies the proposed theory: the maximum pressure load occurs when the phase shift is 90 degrees. A comparison of the present computational results to the previous comprehensive experimental data validates the maximum pressure theory. When the baffle is submerged, the maximum pressure theory envelopes all the experimental data points.

CFD↗

Pronghorn Porous Media Model Validation with Pressure Drop Measurements

The verification and validation (V&V) of Pronghorn is imperative to assert its accuracy when predicting the fluid velocity, temperature, and pressure in high temperature gas-cooled reactors. Pronghorn is a coarse-mesh, intermediate-fidelity, and multidimensional thermal-hydraulics (TH) code developed by the Idaho National Laboratory (INL). New pebble bed experiments are used to observe the details of the fluid motion and pressure drop in the porous bed under the reactor normal operation. This paper focuses on the validation of the Pronghorn compressible and incompressible Navier-Stokes equations using the pressure drop measurements performed at the engineering-scale pebble bed facility at the Texas A&M university (TAMU). Various pressure drop correlations and porosity functions are implemented in both Pronghorn and STAR-CCM+ to compare the pressure drop due to the combined viscous and inertial resistances in the porous bed. The correlations accounting for the near-wall effect are also utilized to observe if the pressure drop estimates can be improved. Pronghorn porous media models predict the pressure drop well relative to the STAR-CCM+ simulation results and 1D correlations, and both the finite element method (FEM) and finite volume method (FVM) perform accurately. Pronghorn models are also validated with the experimental measurements given the different Reynolds number ranges and specific aspect ratios. The likelihood of the statistical significance between the pressure drop measurements and specific correlations or simulations is low provided that the overlap of their confidence intervals is more than the half of a single arm. Several validation metrics are reasonable in regard to the similar studies from other literature. The precise average pebble bed porosity estimation has much impact on the pressure drop, and the Foumeny and Montillet (dense packing) models carry out the accurate pressure drop prediction by considering the near-wall effect.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Pressure‐Dependent “Insulator–Metal–Insulator” Behavior in Sr‐Doped La 3 Ni 2 O 7

Abstract Recently, superconductivity at high temperatures is observed in bulk La 3 Ni 2 O 7−δ under high pressure. However, the attainment of high‐purity La 3 Ni 2 O 7−δ single crystals remains a formidable challenge. Here, the crystal structure and physical properties of single crystals of Sr‐doped La 3 Ni 2 O 7 synthesized at high pressure (20 GPa) and high temperature (1400 °C) are reported. Through single crystal X‐ray diffraction, it is shown that high‐pressure‐synthesized paramagnetic Sr‐doped La 3 Ni 2 O 7 crystallizes in an orthorhombic structure with Ni─O─Ni bond angles of 173.4(2)° out‐of‐plane and 175.0(2)°and 176.7(2)°in plane. The substitution of Sr alters in band filling and the ratio of Ni 2+ /Ni 3+ in Sr‐doped La 3 Ni 2 O 7 , aligning them with those of “La 3 Ni 2 O 7.05” , thereby leading to significant modifications in properties under high pressure relative to the unsubstituted parent phase. At ambient pressure, Sr‐doped La 3 Ni 2 O 7 exhibits insulating properties, and the conductivity increases as pressure goes up to 10 GPa. However, upon further increasing pressure beyond 10.7 GPa, Sr‐doped La 3 Ni 2 O 7 transits back from a metal‐like behavior to an insulator. The insulator–metal–insulator trend under high pressure dramatically differs from the behavior of the parent compound La 3 Ni 2 O 7−δ , despite their similar behavior in the low‐pressure regime. These experimental results underscore the considerable challenge in achieving superconductivity in nickelates.

36 MATERIALS SCIENCE↗

Experimental analysis of pressure distribution in a twin screw compressor for multiphase duties

This paper presents the results of an experimental investigation of pressure distribution inside working chamber of a twin screw compressor for multiphase duties. A mathematical model for describing the pressure distribution inside working chamber is proposed. By means of a small pressure transducer embedded into the groove at the root of the rotor, the pressure distributions of a multiphase compressor under various running conditions have been recorded successfully to verify the model. It is found that the pressure curve during the discharge process has a higher level under the conditions of the lower gas void fraction, higher discharge pressure, higher rotational speed and higher inlet pressure. The pressure distribution calculated by model in this paper shows good agreement with the data recorded by a small pressure sensor in a prototype multiphase compressor at the high gas void fractions under different operating conditions. (author)

42 ENGINEERING↗

Impact of Xe partial pressure on the production of excimer vacuum ultraviolet emission for plasma display panels

In this work, the effect of the Xe partial pressure on the excimer vacuum ultraviolet (VUV) emission intensity of the plasma display panels is investigated, both by measuring the spectral emission directly and by two-dimensional simulations. Experimentally, we find that at the high Xe partial pressure levels, there is an supra-linear increase of excimer VUV radiation and that determines the strong increase of luminance at the high pressures and high voltage. Due to the increase of the luminance and the almost unchanged discharge current, the luminous efficacy strongly increases with the Xe partial pressure. In addition, we also investigated the dynamics of the VUV generation, by measuring the decay time of the excimer VUV light as a function of the gas pressure. It is found that the decay time decreases with the increase of gas pressure. The spatial characteristics of the excimer VUV emission are also discussed. Different from the Ne and near-infrared emission, the excimer VUV emission is generated near the surface of the electrodes and increases uniformly on both sides of the anode and cathode (i.e., the bulk plasma region). Most importantly, it is found that the VUV production occurs during the afterglow period, while it is almost zero at the moment of the discharge itself. From the simulations, it can be seen that the Xe{sub 2}*({sup 3}{Sigma}{sub u}{sup +}) excimer species, which are generated from Xe*(1s{sub 5}), play a dominant role in the excimer VUV emission output at the high Xe partial pressure. The two-dimensional simulations also show that the strong increase of Xe excimer excitation states in the case of high pressure is mainly the result of the high conversion efficiency of the Xe excimer states, especially in the afterglow period. Due to the high conversion efficiency of Xe excitation species to Xe excimer species by the high collision rate in the case of high pressure, there is a strong increase of excimer VUV production, especially from the cathode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High-pressure behavior of amorphous selenium from ultrasonic measurements and Raman spectroscopy

The high-pressure behavior of melt-quenched amorphous selenium (a-Se) has been investigated via ultrasonic measurements and Raman scattering at room temperature. The ultrasonic measurements were conducted on a-Se in a multi-anvil apparatus with two different sample assemblies at pressures of up to 4.5 and 4.8 GPa. We discovered that similar kinks occur in the slopes of the pressure dependence characteristics of the travel time and the sound velocity in both shear and longitudinal waves in the 2.0–2.5 GPa range. These kinks are independent of the sample assemblies, indicating an intrinsic transformation of the a-Se. Additionally, we deduced the pressure-volume relationship of a-Se from the sound velocity characteristics using the Birch–Murnaghan equation of state, and the results agreed well with those of previous reports. In situ high-pressure Raman scattering measurements of a-Se were conducted in a diamond anvil cell with an 830 nm excitation line up to a pressure of 4.3 GPa. We found that the characteristic band of a-Se at ∼250 cm{sup −1} experienced a smooth shift to a lower frequency with pressure, but a sharp slope change in the band intensity versus pressure occurred near 2.5 GPa. The results of X-ray diffraction and differential scanning calorimetry measurements indicate that the samples remain in their amorphous states after decompression. Thus, we proposed that the abnormal compression behavior of a-Se in the 2.0–2.5 GPa range can be attributed to pressure-induced local atomic reconfiguration, implying an amorphous-amorphous transition of the elementary selenium.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural, elastic, and lattice dynamic stability of yttrium selenide (YSe) under pressure: A first principle study

Structural, elastic, and lattice dynamical stability of YSe has been investigated as a function of pressure through first principles electronic band structure calculations. The comparison of enthalpies of rocksalt type (B1) and CsCl type cubic (B2) structures determined as a function of pressure suggests that the B1 phase will transform to B2 structure at ∼32 (30 GPa at 300 K obtained from comparison of Gibbs free energy at 300 K). The transition is identified to be of first order in nature with a volume discontinuity of ∼6.2% at the transition pressure. Furthermore, the theoretically determined equation of state has been utilized to derive various physical quantities, such as zero pressure equilibrium volume, bulk modulus, and pressure derivative of bulk modulus. The single crystal elastic constants have been predicted at various pressures for both the B1 and B2 structures using the energy strain method. The activation barrier between B1 and B2 phases calculated at transition point is ∼19.7mRy/formula unit. Our lattice dynamic calculations show that both the B1 as well as B2 structures are lattice dynamically stable not only at ambient pressure but also at transition pressure. The B1 phase becomes lattice dynamically unstable at ∼112 GPa, i.e., much beyond the transition pressure. The effect of temperature on volume and bulk modulus of the YSe in B1 phase has also been examined.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

SECARB Pressure Monitoring Data

Bottom-hole, above zone monitoring interval, and injection zone pressure data collected during the SECARB project in Cranfield, Mississippi to assess the relationship between pressure field and multiphase field. Submission includes 10-second interval data from Detailed Area of Study wells: CFU31-F1 (injector), CFU31-F2 (observation), CFU31-F3 (observation) and Ella G Lees no. 7 (observation) well located west of the DAS. Associated Publications: Joy, C. A., 2011, The effects of pressure variation and chemical reactions on the elasticity of the lower Tuscaloosa sandstone of the Cranfield Field Mississippi, The University of Texas at Austin, Master’s thesis, 97 p. Kim, S., and Hosseini, S. A., 2013, Above-zone pressure monitoring and geomechanical analysis of a field scale CO2 injection, Cranfield Mississippi, Greenhouse Gases: Science and Technology, doi:10.1002/ghg.1388. Kim, S., and Hosseini, S. A., 2017, Study on the ratio of pore-pressure/stress changes during fluid injection and its implications for CO2 geologic storage: Journal of Petroleum Science and Engineering, v. 149, p. 138-150, doi:10.1016/j.petrol.2016.10.037. Mathias, S. A., Gluyas, J. G., Gonzalez Martinez de Miguel, G. J., and Hosseini, S. A., 2011, Role of partial miscibility on pressure buildup due to constant rate injection of CO2 into closed and open brine aquifers: Water Resources Research, v. 47, W12525, 11 p., doi:10.1029/2011WR011051. Meckel, T. A., Zeidouni, M., Hovorka, S. D., and Hosseini, S.A., 2013, Assessing sensitivity to well leakage from three years of continuous reservoir pressure monitoring during CO2 injection at Cranfield, MS, USA: International Journal of Greenhouse Gas Control, [insert volume no., page numbers], doi:10.1016/j.ijggc.2013.01.019. Nicot, J.-P., Oldenburg, C. M., Bryant, S. L., and Hovorka, S. D., 2009, Pressure perturbations from geologic carbon sequestration: area-of-review boundaries and borehole leakage driving forces, in Energy Procedia (v. 1, no.1), Proceedings of 9th International Conference on Greenhouse Gas Control Technologies, GHGT9, 16–20 November, Washington DC, p. 47–54. Tao, Q., Bryant, S. L., and Meckel, T. A., 2013, Modeling above-zone measurements of pressure and temperature for monitoring CCS sites: International Journal of Greenhouse Gas Control, v. 18, p. 523–530, doi:10.1016/j.ijggc.2012.08.011.

above zone monitoring interval↗

Investigation and Design Studies of SOFC Electrode Performance at Elevated Pressure

An experimental program was set forth to study fuel cell performance at pressure and under various compositions. Improvement in cathode electrode performance is on the order of 33-40% at pressures of 6.4 Bara compared to atmospheric pressure. Key cathode operational parameters are the concentration and partial pressure of O2, and temperature. The effect of partial pressure of oxygen (PO2) decreases the activation polarization, although there appears to be a secondary effect of absolute pressure as well. The concentration of oxygen impacts the diffusion component of the polarization, which is largely insensitive to absolute pressure. The effect of pressure was found to reduce the total polarization resistance of full fuel-cells beyond the reduction determined for the cathode alone. The total reduction in ASR was on the order of 0.10 ohm-cm2 for a pressure increase from 1 to 6.5 Bara, with about 70% of the improvement being realized from 1 to 4 Bara. An important finding was that there is an effect of steam on the cathode that is highly temperature dependent. The loss of performance at temperatures below 850 C was very large for the standard LSM + YSZ cathodes.

30 DIRECT ENERGY CONVERSION↗

Pressure Safety Program Implementation at ORNL

The Oak Ridge National Laboratory (ORNL) is a US Department of Energy (DOE) facility that is managed by UT-Battelle, LLC. In February 2006, DOE promulgated worker safety and health regulations to govern contractor activities at DOE sites. These regulations, which are provided in 10 CFR 851, Worker Safety and Health Program, establish requirements for worker safety and health program that reduce or prevent occupational injuries, illnesses, and accidental losses by providing DOE contractors and their workers with safe and healthful workplaces at DOE sites. The regulations state that contractors must achieve compliance no later than May 25, 2007. According to 10 CFR 851, Subpart C, Specific Program Requirements, contractors must have a structured approach to their worker safety and health programs that at a minimum includes provisions for pressure safety. In implementing the structured approach for pressure safety, contractors must establish safety policies and procedures to ensure that pressure systems are designed, fabricated, tested, inspected, maintained, repaired, and operated by trained, qualified personnel in accordance with applicable sound engineering principles. In addition, contractors must ensure that all pressure vessels, boilers, air receivers, and supporting piping systems conform to (1) applicable American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (2004) Sections I through XII, including applicable code cases; (2) applicable ASME B31 piping codes; and (3) the strictest applicable state and local codes. When national consensus codes are not applicable because of pressure range, vessel geometry, use of special materials, etc., contractors must implement measures to provide equivalent protection and ensure a level of safety greater than or equal to the level of protection afforded by the ASME or applicable state or local codes. This report documents the work performed to address legacy pressure vessel deficiencies and comply with pressure safety requirements in 10 CFR 851. It also describes actions taken to develop and implement ORNL’s Pressure Safety Program.

42 ENGINEERING↗

Compression under a mechanical counter pressure space suit glove

Background: Current gas-pressurized space suits are bulky stiff shells severely limiting astronaut function and capability. A mechanical counter pressure (MCP) space suit in the form of a tight elastic garment could dramatically improve extravehicular activity (EVA) dexterity, but also be advantageous in safety, cost, mass and volume. The purpose of this study was to verify that a prototype MCP glove exerts the design compression of 200 mmHg, a pressure similar to the current NASA EVA suit. Methods: Seven male subjects donned a pressure measurement array and MCP glove on the right hand, which was placed into a partial vacuum chamber. Average compression was recorded on the palm, the bottom of the middle finger, the top of the middle finger and the dorsum of the hand at pressures of 760 (ambient), 660 and 580 mmHg. The vacuum chamber was used to simulate the pressure difference between the low breathing pressure of the current NASA space suits (approximately 200 mmHg) and an unprotected hand in space. Results: At ambient conditions, the MCP glove compressed the dorsum of the hand at 203.5 +/- 22.7 mmHg, the bottom of the middle finger at 179.4 +/- 16.0 mmHg, and the top of the middle finger at 183.8 +/- 22.6 mmHg. The palm compression was significantly lower (59.6 +/- 18.8 mmHg, p<0.001). There was no significant change in glove compression with the chamber pressure reductions. Conclusions: The MCP glove compressed the dorsum of the hand and middle finger at the design pressure.

NASA Discipline Life Sciences Technologies↗

THE EFFECT OF 3HE ON LOW PRESSURE HYDRIDE ABSORPTION MEASUREMENTS WITH TRITIUM

Absorption isotherm data exists for a wide variety of hydrogen-metal systems. When working with high purity gases, appropriately sized equipment, and hydrides with equilibrium pressures above several hundred Pa, data collection is relatively straightforward. Special consideration must be given to experiments involving low equilibrium pressure hydrides, as even sub-ppm levels of gas impurities can generate partial pressures many times greater than the equilibrium pressures to be measured. Tritium absorption experiments are further complicated by the continuous generation of helium-3. The time required to transfer and absorb a known quantity of tritium onto a sample ultimately limits the minimum pressure range that can be studied using the standard technique. Equations are presented which show the pressure of helium-3 in a sample cell based on the amount of tritium to be absorbed, the sample cell volume and temperature, and the decay time of tritium. Sample calculations for zirconium show that at 300 C, the estimated helium-3 pressure in the cell will be equal to the hydrogen absorption pressure after only milliseconds of tritium decay. An alternate method is presented that permits the collection of equilibrium data at pressures orders of magnitude lower than possible using a direct approach.

08 HYDROGEN↗

Explosion bomb measurements of ethanol-air laminar gaseous flame characteristics at pressures up to 1.4 MPa

The principal burning characteristics of a laminar flame comprise the fuel vapour pressure, the laminar burning velocity, ignition delay times, Markstein numbers for strain rate and curvature, the stretch rates for the onset of flame instabilities and of flame extinction for different mixtures. With the exception of ignition delay times, measurements of these are reported and discussed for ethanol-air mixtures. The measurements were in a spherical explosion bomb, with central ignition, in the regime of a developed stable, flame between that of an under or over-driven ignition and that of an unstable flame. Pressures ranged from 0.1 to 1.4 MPa, temperatures from 300 to 393 K, and equivalence ratios were between 0.7 and 1.5. It was important to ensure the relatively large volume of ethanol in rich mixtures at high pressures was fully evaporated. The maximum pressure for the measurements was the highest compatible with the maximum safe working pressure of the bomb. Many of the flames soon became unstable, due to Darrieus-Landau and thermo-diffusive instabilities. This effect increased with pressure and the flame wrinkling arising from the instabilities enhanced the flame speed. Both the critical Peclet number and the, more rational, associated critical Karlovitz stretch factor were evaluated at the onset of the instability. With increasing pressure, the onset of flame instability occurred earlier. The measured values of burning velocity are expressed in terms of their variations with temperature and pressure, and these are compared with those obtained by other researchers. Some comparisons are made with the corresponding properties for iso-octane-air mixtures. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

On scale and magnitude of pressure build-up induced by large-scale geologic storage of CO2

The scale and magnitude of pressure perturbation and brine migration induced by geologic carbon sequestration is discussed assuming a full-scale deployment scenario in which enough CO{sub 2} is captured and stored to make relevant contributions to global climate change mitigation. In this scenario, the volumetric rates and cumulative volumes of CO{sub 2} injection would be comparable to or higher than those related to existing deep-subsurface injection and extraction activities, such as oil production. Large-scale pressure build-up in response to the injection may limit the dynamic storage capacity of suitable formations, because over-pressurization may fracture the caprock, may drive CO{sub 2}/brine leakage through localized pathways, and may cause induced seismicity. On the other hand, laterally extensive sedimentary basins may be less affected by such limitations because (i) local pressure effects are moderated by pressure propagation and brine displacement into regions far away from the CO{sub 2} storage domain; and (ii) diffuse and/or localized brine migration into overlying and underlying formations allows for pressure bleed-off in the vertical direction. A quick analytical estimate of the extent of pressure build-up induced by industrial-scale CO{sub 2} storage projects is presented. Also discussed are pressure perturbation and attenuation effects simulated for two representative sedimentary basins in the USA: the laterally extensive Illinois Basin and the partially compartmentalized southern San Joaquin Basin in California. These studies show that the limiting effect of pressure build-up on dynamic storage capacity is not as significant as suggested by Ehlig-Economides and Economides, who considered closed systems without any attenuation effects.

54 ENVIRONMENTAL SCIENCES↗

Experimental study and demonstration of pilot-scale, dry feed, oxy-coal combustion under pressure

In this paper, we discuss how pressurized oxy-combustion is a promising technology for low-carbon, fossil fuel utilization. It has the potential of improved efficiency and economics compared with conventional atmospheric pressure oxy-combustion. Washington University in St. Louis has proposed a new pressurized oxy-combustion process, namely Staged Pressurized Oxy-Combustion, which has the potential to improve further the plant efficiency, operational flexibility, and economics. This process burns pulverized coal in a pressurized, oxy-combustion environment, which has not been demonstrated in a pilot-scale system before. To address this gap, a 100 kWth pressurized oxy-combustion facility was designed and constructed. This facility has a unique burner and furnace design featuring a co-axial, low-mixing flow field, which is drastically different from conventional coal-fired boiler designs where strong mixing is sought by introducing swirl or recirculating flows. This work aims to present the first pilot-scale experimental results of a dry-feed, pressurized oxy-combustion system. The tests focused on exploring flame stability and shape, char burnout, and fine particulate matter formation. Testing results suggest that the burner has excellent flame stability. The flame shape is consistent with the design philosophy and agrees with large eddy simulations. Importantly, complete char combustion can be achieved with an oxygen mole fraction in the flue gas of only 0.8%, as opposed to a required value of ~3% for conventional atmospheric pressure air-fired or oxyfuel combustion, which reduces the costs of both oxygen generation upstream and oxygen removal downstream. The testing results show promise for dry-feed, pressurized oxy-combustion, and the new burner and furnace design.

01 COAL, LIGNITE, AND PEAT↗

Associations between cadmium levels in blood and urine, blood pressure and hypertension among Canadian adults

Background: Cadmium has been inconsistently related to blood pressure and hypertension. The present study seeks to clarify the relationship between cadmium levels found in blood and urine, blood pressure and hypertension in a large sample of adults. Methods: The study sample included participants ages 20 through 79 from multiple cycles of the Canadian Health Measures Survey (2007 through 2013) with measured blood cadmium (n=10,099) and urinary cadmium (n=6988). Linear regression models examined the association between natural logarithm transformed cadmium levels and blood pressure (separate models for systolic and diastolic blood pressure) after controlling for known covariates. Logistic regression models were used to examine the association between cadmium and hypertension. Models were run separately by sex, smoking status, and body mass index category. Results: Men had higher mean systolic (114.8 vs. 110.8 mmHg, p<0.01) and diastolic (74.0 vs. 69.6 mmHg, p<0.01) blood pressure compared to women. Although, geometric mean blood (0.46 vs. 0.38 µg/L, p<0.01) and creatinine-adjusted standardized urinary cadmium levels (0.48 vs. 0.38 µg/L, p<0.01) were higher among those with hypertension, these differences were no longer significant after adjustment for age, sex and smoking status. In overall regression models, increases in blood cadmium were associated with increased systolic (0.70 mmHg, 95% confidence interval [CI]=0.25–1.16, p<0.01) and diastolic blood pressure (0.74 mmHg, 95% CI=0.30–1.19, p<0.01). The associations between urinary cadmium, blood pressure and hypertension were not significant in overall models. Model stratification revealed significant and negative associations between urinary cadmium and hypertension among current smokers (OR=0.61, 95% CI=0.44–0.85, p<0.01), particularly female current smokers (OR=0.52, 95% CI=0.32–0.85, p=0.01). Conclusion: This study provides evidence of a significant association between cadmium levels, blood pressure and hypertension. However, the significance and direction of this association differs by sex, smoking status, and body mass index category. - Highlights: • Blood and urinary cadmium levels higher among those with hypertension. • Evidence of association between cadmium levels, blood pressure and hypertension. • Significance and direction of association differs by sex, smoking status, and BMI. • Higher urinary cadmium levels lower hypertension risk for current (female) smokers.

54 ENVIRONMENTAL SCIENCES↗

Numerical investigation of the pressure-dependence of yield sooting indices for n-alkane and aromatic species

The pressure-dependence of the Yield Sooting Index (YSI), as a measure of sooting tendency, is numerically investigated for pressures ranging from 1 atm to 15 atm. Straight-chain alkanes, including ethane, propane, n-hexane, n-heptane, and n-dodecane, and aromatic species, including benzene, toluene, xylene, and ethylbenzene, are selected as test fuels. A detailed chemical mechanism is used for all test fuels considered, and a flamelet-based YSI simulation methodology is employed, where the YSI values are computed based on the Polycyclic Aromatic Hydrocarbon (PAH) dimer production rate at each pressure. It is found that the maximum flame centerline soot volume fraction increases with increasing pressure for all test compounds. However, the pressure dependence of the maximum soot volume fraction is similar for the hydrocarbons within the same class (n-alkane or aromatics). As a consequence, the YSI values computed at pressures up to 15 atm show only small deviations from their values computed and measured at atmospheric pressure. These results suggest that YSI is robust also at elevated pressures, close to those found in practical combustion devices. This study is entirely based on numerical simulations without any experimental measurements available for direct validation. Experimental YSI measurements at high pressures would be required to fully confirm the conclusions reported in this manuscript. Still, our numerical results provide some guidelines for the design of such experiments in the future.

42 ENGINEERING↗