Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PITCHES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Kinematics and aerodynamics of the velocity vector roll

The velocity vector roll is an angular rotation of an aircraft about its instantaneous velocity vector, constrained to be performed at constant angle-of-attack (AOA), no sideslip, and constant velocity. Consideration of the aerodynamic force equations leads to requirements for body-axis yawing and pitching rotations that satisfy these constraints. Here, the body axis rotations, and the constraints, are used in the moment equations to determine the aerodynamic moments required to perform the velocity vector roll. For representative tactical aircraft, the conditions for maximum pitching moment are a function of orientation, occurring at about 90 deg of bank in a level trajectory. Maximum required pitching moment occurs at peak roll rate, and is achieved at AOA above 45 deg. The conditions for maximum rolling moment depend on the value of the roll mode time constant. For a small time constant (fast response) the maximum rolling moment occurs at maximum roll acceleration and zero AOA, largely independent of aircraft orientation; for a large time constant, maximum required rolling moment occurs at maximum roll rate, at maximum AOA, and at 180 deg of bank in level flight. Maximum yawing moment occurs at maximum roll acceleration, maximum AOA, and is largely independent of airplane orientation.

Durham, Wayne C.↗

Airfoil Lift with Changing Angle of Attack

Tests have been made in the atmospheric wind tunnel of the National Advisory Committee for Aeronautics to determine the effects of pitching oscillations upon the lift of an airfoil. It has been found that the lift of an airfoil, while pitching, is usually less than that which would exist at the same angle of attack in the stationary condition, although exceptions may occur when the lift is small or if the angle of attack is being rapidly reduced. It is also shown that the behavior of a pitching airfoil may be qualitatively explained on the basis of accepted aerodynamic theory.

Reid, Elliott G↗

Aerodynamic characteristics of several airfoils of low aspect ratio

This paper presents the results of wind-tunnel tests of several airfoils of low aspect ratio. The airfoils included three circular Clark Y airfoils with different amounts of dihedral, two Clark Y airfoils with slots in their portions, and three flat-plate airfoils. Lift, drag, and pitching-moment characteristics of the slotted airfoils with slots open and closed; pitching moment characteristics of one of the slotted airfoils with slots open and closed; and lift characteristics of the flat-plate airfoils are included. The results reveal a definite improvement of lift, drag, and pitching-moment characteristics with increase in dihedral of the circular Clark Y wing. Lift characteristics near the stall were found to depend markedly on the shape of the extreme tip but were not greatly affected by slots through the after portion of the airfoils. Changes in plan form of the flat-plate airfoils gave erroneous indications of the effect to be expected from changes in plan form of an airfoil of Clark Y section. The minimum drag characteristics of the circular Clark Y airfoils were found to be substantially the same as for a Clark Y airfoil of conventional aspect ratio.

Zimmerman, C H↗

A method of calculating the performance of controllable propellers with sample computations

This paper contains a series of calculations showing how the performance of controllable propellers may be derived from data on fixed-pitch propellers given in N.A.C.A. Technical Report No. 350, or from similar data. Sample calculations are given which compare the performance of airplanes with fixed-pitch and with controllable propellers. The gain in performance with controllable propellers is shown to be largely due to the increased power available, rather than to an increase in efficiency. Controllable propellers are of particular advantage when used with geared and with supercharged engines. A controllable propeller reduces the take-off run, increases the rate of climb and the ceiling, but does not increase the high speed, except when operating above the design altitude of the previously used fixed-pitch propeller or when that propeller was designed for other than high speed.

Hartman, Edwin P↗

Longitudinal Stability and Control Characteristics as Determined by the Rocket-model Technique for an Inline, Cruciform, Canard Missile Configuration with a Low-aspect-ratio Wing Having Trailing-edge Flap Controls for a Mach Number Range of 0.7 to 1.

Two full-scale models of an inline, cruciform, canard missile configuration having a low-aspect-ratio wing equipped with flap-type controls were flight tested in order to determine the missile's longitudinal aerodynamic characteristics. Stability derivatives and control and drag characteristics are presented for a range of Mach number from 0.7 to 1.8. Nonlinear lift and moment curves were noted for the angle - of-attack range of this test (0 deg to 8 deg). The aerodynamic-center location for angles of attack near 50 remained nearly constant for supersonic speeds at 13.5 percent of the mean aerodynamic chord; whereas for angles of attack near 0 deg, there was a rapid forward movement of the aerodynamic center as the Mach number increased. At a control deflection of 0 deg, the missile's response to the longitudinal control was in an essentially fixed space plane which was not coincident with the pitch plane as a result of the missile rolling. As a consequence, stability characteristics were determined from the resultant of pitch and yaw motions. The damping-in-pitch derivatives for the two angle -of-attack ranges of the test are in close agreement and varied only slightly with Mach number. The horn-balanced trailing-edge flap was effective in producing angle of attack over the Mach number range.

Baber, Hal T , Jr↗

Some Effects of Roll Rate on the Longitudinal Stability Characteristics of a Cruciform Missile Configuration as Determined from Flight Test for a Mach Number Range of 1.1. to 1.8

A model of a cruciform missile configuration having a low-aspect-ratio wing equipped with flap-type controls was flight tested in order to determine stability and control characteristics while rolling at about 5 radians per second. Comparison is made with results from a similar model which rolled at a much lower rate. Results showed that, if the ratio of roll rate to natural circular frequency in pitch is not greater than about 0.3, the motion following a step disturbance in pitch essentially remains in a plane in space. The slope of normal- force coefficient against angle of attack C(sub N(sub alpha)) was the same as for the slowly rolling model at 0 degrees control deflection but C(sub N(sub alpha)) was much higher for the faster rolling model at about 5 degrees control deflection. The slope of pitching-moment coefficient against angle of attack C(sub m(sub alpha)) as determined from the model period of oscillation was the same for both models at 0 degrees control deflection but was lower for the faster rolling model at about 5 degrees control deflection. Damping data for the faster rolling model showed considerably more scatter than for the slowly rolling model.

Lundstrom, Reginald R↗

Flight Investigation at Low Angles of Attack to Determine the Longitudinal Stability and Control Characteristics of a Cruciform Canard Missile Configuration with a Low-Aspect-Ratio Wing and Blunt Nose at Mach Numbers from 1.2 to 2.1

A full- scale rocket-powered model of a cruciform canard missile configuration with a low- aspect - ratio wing and blunt nose has been flight tested by the Langley Pilotless Aircraft Research Division. Static and dynamic longitudinal stability and control derivatives of this interdigitated canard-wing missile configuration were determined by using the pulsed- control technique at low angles of attack and for a Mach number range of 1.2 to 2.1. The lift - curve slope showed only small nonlinearities with changes in control deflection or angle of attack but indicated a difference in lift- .curve slope of approximately 7 percent for the two control deflections of delta = 3.0 deg and delta= -0.3 deg . The large tail length of the missile tested was effective in producing damping in pitch throughout the Mach number range tested. The aerodynamic- center location was nearly constant with Mach number for the two control deflections but was shown to be less stable with the larger control deflection. The increment of lift produced by the controls was small and positive throughout the Mach number range tested, whereas the pitching moment produced by the controls exhibited a normal trend of reduced effectiveness with increasing Mach number.The effectiveness of the controls in producing angle of attack, lift, and pitching moment was good at all Mach numbers tested.

Brown, Clarence A , Jr↗

Effect of Propeller-Axis Angle of Attack on Thrust Distribution over the Propeller Disk in Relation to Wake-Survey Measurement of Thrust

Tests were made to investigate the variation of thrust distribution over the propeller disk with angle of pitch of the propeller thrust axis and to determine the disposition and the minimum number of rakes necessary to measure the propeller thrust. The tests were made at a low Mach number for a low and a high blade angle with the propeller operating at three small angles of pitch, and some of the tests were repeated at a higher Mach number. The data obtained show that, for small angles of pitch, large changes occur in the energy distribution in the wake which prohibit the use of a single survey rake for thrust measurement in flight tests and limit the use of a single rake in wind-tunnel tests. Under certain conditions, the energy distribution in the wake took on a symmetrical form and two diametrically opposed survey rakes were shown to be satisfactory for obtaining propeller thrust. (author)

Pendley, Robert E↗

Report on Behavior of Aeroplanes in Gusts

Part 1 presents the results of a wind tunnel test of a biplane model with an 18 inch span. The lift, drift, and pitching moment were measured for a series of angles of incidence corresponding to the maximum possible changes of flight attitude. Only the discussion of symmetrical or longitudinal changes is given. From the observed rate of variation of the forces and pitching moment, it was possible to calculate the derivatives needed in the complete theory of longitudinal stability in still air. The damping of the pitching oscillation was also determined experimentally. Part 2 presents a theoretical method for determining the effects of gusts on aeroplanes in the following cases: (1) head-on gusts rising from 0 to j feet per second with various degrees of sharpness, (2) up gusts of the same type, (3) rotary gusts of the same type, (4) rear gusts and down gusts are included by merely changing the sign of j.

Hunsaker, J C↗

Experimental Determination of Jet Boundary Corrections for Airfoil Tests in Four Open Wind Tunnel Jets of Different Shapes

This experimental investigation was conducted primarily for the purpose of obtaining a method of correcting to free air conditions the results of airfoil force tests in four open wind tunnel jets of different shapes. Tests were also made to determine whether the jet boundaries had any appreciable effect on the pitching moments of a complete airplane model. Satisfactory corrections for the effect of the boundaries of the various jets were obtained for all the airfoils tested, the span of the largest being 0.75 of the jet width. The corrections for angle of attack were, in general, larger than those for drag. The boundaries had no appreciable effect on the pitching moments of either the airfoils or the complete airplane model. Increasing turbulence appeared to increase the minimum drag and maximum lift and to decrease the pitching moment.

Knight, Montgomery↗

Comparison of Full-Scale Propellers Having R.A.F.-6 and Clark Y Airfoil Sections

In this report the efficiencies of two series of propellers having two types of blade sections are compared. Six full-scale propellers were used, three having R. A. F.-6 and three Clark Y airfoil sections with thickness/chord ratios of 0.06, 0.08, and 0.10. The propellers were tested at five pitch setting, which covered the range ordinarily used in practice. The propellers having the Clark Y sections gave the highest peak efficiency at the low pitch settings. At the high pitch settings, the propellers with R. A. F.-6 sections gave about the same maximum efficiency as the Clark Y propellers and were more efficient for the conditions of climb and take-off.

Freeman, Hugh B↗

Air Propellers in Yaw

Report presents the results of tests conducted at Stanford University of a 3-foot model propeller at four pitch settings and at 0 degree, 10 degrees, 20 degrees, and 30 degrees yaw. In addition to the usual propeller coefficients, cross-wind and vertical forces and yawing, pitching, and rolling moments were determined about axes having their origin at the intersection of the blade axis and the axis of rotation. The tests showed that the maximum efficiency was reduced only slightly for angles of yaw up to 10 degrees but that at 30 degrees yaw the loss in efficiency was about 10 percent. In all cases the cross-wind force was found to be greater than the cross-wind component of the axial thrust. With a yawed propeller an appreciable thrust was found for v/nd for zero thrust at zero yaw. Yawing a propeller was found to induce a pitching moment that increased in magnitude with yaw.

Lesley, E P↗

Experimental Aerodynamic Derivatives of a Sinusoidally Oscillating Airfoil in Two-Dimensional Flow

Experimental measurements of the aerodynamic reactions on a symmetrical airfoil oscillating harmonically in a two-dimensional flow are presented and analyzed. Harmonic motions include pure pitch and pure translation, for several amplitudes and superimposed on an initial angle of attack, as well as combined pitch and translation. The apparatus and testing program are described briefly and the necessary theoretical background is presented. In general, the experimental results agree remarkably well with the theory, especially in the case of the pure motions. The net work per cycle for a motion corresponding to flutter is experimentally determined to be zero. Considerable consistent data for pure pitch were obtained from a search of available reference material, and several definite Reynolds number effects are evident.

Halfman, Robert L↗

Charts for estimating performance of high-performance helicopters

Theoretically derived charts showing the profile-drag-thrust ratio are presented for helicopter rotors operating in forward flight and having hinged rectangular blades with a linear twist of 0 degree, 8 degrees, and 16 degrees. The charts, showing the profile-drag characteristics of the rotor for various combinations of pitch angle, ratio of thrust coefficient to solidity, and a parameter representing shaft power input, are presented for tip-speed ratios ranging from 0.05 to 0.50. Also presented in chart form are the ratio of thrust coefficient to solidity as a function of angles of attack, as a function of inflow ratio and collective pitch, and as a function of power and thrust coefficients. The charts in this report are considered more accurate than previous ones for flight conditions involving high inflow velocities and large regions of reversed velocity that may be encountered by high-performance helicopters. The charts may be used to study the effects of design changes on rotor performance and to indicate optimum performance conditions, as well as to estimate quickly rotor performance in forward flight. They are also useful in obtaining inflow-ratio and pitch-angle values for use in calculating flapping coefficients and spanwise loadings. The method of applying the charts to performance estimation is illustrated through sample calculation of a typical rotor-performance problem.

Gessow, Alfred↗

A four-axis hand controller for helicopter flight control

A proof-of-concept hand controller for controlling lateral and longitudinal cyclic pitch, collective pitch and tail rotor thrust was developed. The purpose of the work was to address problems of operator fatigue, poor proprioceptive feedback and cross-coupling of axes associated with many four-axis controller designs. The present design is an attempt to reduce cross-coupling to a level that can be controlled with breakout force, rather than to eliminate it entirely. The cascaded design placed lateral and longitudinal cyclic in their normal configuration. Tail rotor thrust was placed atop the cyclic controller. A left/right twisting motion with the wrist made the control input. The axis of rotation was canted outboard (clockwise) to minimize cross-coupling with the cyclic pitch axis. The collective control was a twist grip, like a motorcycle throttle. Measurement of the amount of cross-coupling involved in pure, single-axis inputs showed cross coupling under 10 percent of full deflection for all axes. This small amount of cross-coupling could be further reduced with better damping and force gradient control. Fatigue was not found to be a problem, and proprioceptive feedback was adequate for all flight tasks executed.

Demaio, Joe↗

Kinetic plasma processes occurring in the outer plasmasphere

One area of data analysis work that was begun under this contract is the fitting of the perpendicular velocity distributions of equatorially trapped ions with a Kappa function. This type of characterization of the trapped ions will be very useful for comparison with velocity distributions produced by the model. A second area of data analysis is to study data from consecutive passes when DE 1's apogee was near the magnetic equator and the spacecraft was often skimming along nearly the same L shell. In 1982 three such periods occurred in May, June, and July. For these consecutive events we have Kp histories, density measurements from a number of sources (Whistler data, DE SFR, ISEE SFR) and consecutive samples of ion pitch angle distributions along field lines. It is clear from this data how the pitch angle distributions evolve during a flux tube refilling event. Our modeling of the flow of plasma along closed field lines is following two basic tracks. The first is a study of the basic refilling process without the effect of wave-particle heating near the equator or the effect of large or abrupt field-aligned electric potential drops. This model includes the effects of Coulomb self-collisions and collisions with the O+ ions in the topside ionosphere. The second track is a study of the effects of wave produced pitch-angle scattering and perpendicular heating occurring near the magnetic equator, in connection with the development of large potential drops that result from electron heating and the development of density gradients.

Wilson, Gordon R.↗

An experimental and theoretical study of the aerodynamic characteristics of some generic missile concepts at Mach numbers from 2 to 6.8

A study has been made of the experimental and theoretical aerodynamic characteristics for some generic high-speed missile concepts at Mach numbers from 2 to 6.8. The basic body for this study had a length-to-diameter ratio of 10 with the forward half being a modified blunted ogive and the rear half being a cylinder. Modifications made to the basic body included the addition of an after body flare, the addition of highly swept cruciform wings and the addition of highly swept aft tails. The effects of some controls were also investigated with all-moving wing controls on the flared body and trailing-edge flap controls on the winged body. The results indicated that the addition of a flare, wings, or tails to the basic body all provided static longitudinal stability with varying amounts of increased axial force. The control arrangements were effective in producing increments of normal-force and pitching-moment at the lower Mach numbers. At the highest Mach number, the flap control on the winged body was ineffective in producing normal-force or pitching-moment but the all-moving wing control on the flared body, while losing pitch effectiveness, still provided normal-force increments. Calculated results obtained through the use of hypersonic impact theory were in generally good agreement with experiment at the higher Mach numbers but were not accurate at the lower Mach numbers.

Spearman, M. Leroy↗

Sensitivity of lag-damping correlations to structural and aerodynamic approximations of isolated experimental rotors in forward flight

The predictions of regressive lag-mode damping levels are correlated with the database of an isolated, soft-inplane, three-blade rotor operated untrimmed. The database was generated at the Army Aeroflightdynamics Directorate at Ames. The correlation covers a broad range of data, from near-zero thrust conditions in hover to high-thrust and highly stalled conditions in forward flight with advance ratio as high as 0.55 and shaft angle as high as 20 degrees. In the experimental rotor, the airfoil or blade portion has essentially uniform mass and stiffness distributions, but the root flexure has highly nonuniform mass and stiffness distributions. Accordingly, the structural approximations refer to four models of root-flexure-blade assembly. They range from a rigid flap-lag model to three elastic flap-lag-torsion models, which differ in modeling the root flexure. The three models of root-flexure are: three root springs in which the bending-torsion couplings are fully accounted for; a finite-length beam element with some average mass and stiffness distributions such that the fundamental frequencies match those of the experimental model; and accurate modal representation in which the actual mass and stiffness distributions of the experimental root-flexure-blade assembly are used in calculating the nonrotating mode shapes. The four models of root-flexure-blade assembly are referred to as the rigid flap-lag model, spring model, modified model and modal model. For each of these four models of the root-flexure-blade assembly, the predictions are based on the following five aerodynamic theories: ear theory, which accounts for large angle-of-attack and reverse-flow effects on lift, and has constant drag and pitching moment; quasisteady stall theory, which includes quasisteady stall lift, drag and pitching moment characteristics of the airfoil section, dynamics stall theory, which uses the ONERA dynamic stall models of lift, drag and pitching moment; dynamic wake theory, which is based on a finite-state three-dimensional wake model and includes all wake effects including both shed and trailing vorticity; and dynamics and wake theory, which combines both dynamic stall theory and dynamic wake theory and is a relatively complete aerodynamic representation.

Gaonkar, G. H.↗