Investigation of the optical properties of silicon solar cell component materials
Normal incidence reflectance data and optical constants of silicon and germanium extrapolated to maximum and minimum limits
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Normal incidence reflectance data and optical constants of silicon and germanium extrapolated to maximum and minimum limits
The data set consists of calibrated zenith shortwave spectral radiances (400-950 nm and 940-1665 nm) and cloud optical depth (COD) retrievals every 2 seconds. The field of view is 0.5 degree. Retrievals of cloud droplet effective radius and thermodynamic phase are currently experimental and done offline. Effective radius and phase are not in this data set.
Two Co{sub 2}CrAl alloy samples subjected to different heat treatment regimes are studied. An exact distribution of atoms over the sublattices in the samples is determined by X-ray diffraction and neutron diffraction methods. These data are used to perform ab initio density of states calculations and to calculate the magnetic moments of the samples in a coherent potential approximation. The calculated magnetic moments are compared to the experimental values. The effect of atomic ordering on the electronic structure near the Fermi level is analyzed using optical methods. The possible causes of the detected temperature dependence of the electrical resistivity, unusual for metallic alloys, are discussed.
In{sub 2}O{sub 3} films on Al{sub 2}O{sub 3} (012) substrates are fabricated by dc magnetron sputtering at various temperatures (20–600°C). The effect of annealing and the substrate temperature on the film properties are studied by the ellipsometric method and the optical transmission method. Refractive-index profiles are constructed and band gaps for direct and indirect transitions are found. It is established that annealing leads to densification of the film material and unifies the refractive index. Annealing also decreases and unifies the energies of band-to-band transitions, which can be explained by lowering the influence of barriers in annealed films. However, the band gap for direct transitions varies greater than for indirect transitions. This fact can be associated with the mechanism of indirect transitions, notably, the participation of phonons facilitates interband transitions even if they are hindered by extra barriers caused by grain boundaries. The latter can be indirect evidence of the actuality of indirect transitions in indium oxide.
The optical spectra of neutral oxygen vacancies (F 0 centers) in the bulk MgO lattice are investigated using density matrix embedding theory. The impurity Hamiltonian is solved with the complete active space self-consistent field and second-order n-electron valence state perturbation theory (NEVPT2-DMET) multireference methods. Here, to estimate defect-localized vertical excitation energies at the nonembedding and thermodynamic limits, a double extrapolation scheme is employed. The extrapolated NEVPT2-DMET vertical excitation energy value of 5.24 eV agrees well with the experimental absorption maxima at 5.03 eV, whereas the excitation energy value of 2.89 eV at the relaxed triplet defect-localized state geometry overestimates the experimental emission at 2.4 eV by only nearly 0.5 eV, indicating the involvement of the triplet–singlet decay pathway.
The optical constants (n(r), n(i)) for solid ammonia in the cubic phase from 0.14 to 200 microns are displayed in both graphical and tabular form. The refractive indices n(r) were obtained from previously published spectra of the absorption index n(i) by means of the Kramers-Kronig dispersion relation. Mie scattering parameters in the same spectral range are graphically illustrated for particle sizes from 1 to 100 microns. An application of these results to the atmosphere of the planet Jupiter is also presented.
Graphical abstract: - Highlights: • ZnO nanoparticles were prepared by solution combustion method. • PVA–ZnO nanocomposites were synthesized by solution casting method. • Doped and undoped films were characterized using different techniques. • Red shift in optical band gap was observed in Nanocomposite films with respect to nano ZnO. • Photoluminescence intensity was found to be optimum for PVA–10 mol% ZnO nanocomposite film. - Abstract: Nanocomposites of poly vinyl alcohol (PVA) and ZnO have been synthesized using the solution casting technique for different concentrations of nano ZnO powder prepared by low temperature solution combustion method. The formation of polymer nanocomposite and changes in the structural and micro structural properties of the materials were investigated by X-ray diffraction, Energy dispersive X ray spectroscopy and optical microscopy techniques (FTIR and UV–Visible). The surface morphology of PVA–ZnO nanocomposite films were elucidated using Scanning Electron Microscopy. The optical absorption spectrum of nano ZnO shows blue shift in the optical band gap energy with respect to characteristic bulk ZnO at room temperature, whereas PVA–ZnO hybrid films show red shift with respect to nano ZnO. The photoluminescence studies show that the intensity of the blue emission (470 nm) varies with change in concentration of ZnO with an optimum intensity observed at 10 mol% of ZnO.
Yttrium iron garnet films were deposited on Si and Si/CeO{sub 2} substrates by magnetron sputtering method followed by postannealing. By varying the fabrication parameters such as sputtering atmosphere, sputtering power, and annealing atmosphere, single phase garnet films were obtained with different off-stoichiometry and film density. The dependence of cation ratio, magnetic and magneto-optical characteristics, and absorption coefficient were systemically investigated. The results reveal that a proper oxygen pressure in both sputtering and annealing process give rise to a small cation ratio of (Fe{sup 2+} or Fe{sup 4+})/Fe{sup 3+}, thus is beneficial to obtain large saturation magnetization, large Faraday rotation, and small optical absorption. The sputtering power can also affect the properties of the film through changing the film density. Our results indicate that the properties of sputtering deposited yttrium iron garnet (YIG) film can be easily tuned and optimized by modifying the off-stoichiometry and density of the film, thus provides flexibility to fabricate YIG film for extensive applications.
Here, this paper presents detailed characterization and analyses of the optical, electrical, and contact properties of a 35 nm phosphorus-doped (n-type) polysilicon (poly-Si) and a 250 nm boron-doped (p-type) poly-Si deposited respectively on textured and roughed surface. These layers could be applied respectively to the front and rear sides of an n-type Si to produce back junction bifacial screen-printed double-side tunnel oxide passivated contacts (DS-TOPCon) solar cells. Optical and device modeling revealed a short circuit current density loss of 1.5 mA/cm 2 and 0.5 mA/cm 2 due to absorption in the front n-TOPCon and rear side p-TOPCon layers, respectively. The passivation and contact properties including metalized and unmetallized recombination current density (J 0 ), as well as contact resistivity, were determined as a function of contact firing temperature in the range of 700~800°C. The passivation quality of the front thin n-TOPCon was found to deteriorate with increased firing temperature while the rear thick p-TOPCon improved. The study showed that the simulated contact firing at 730°C resulted in the best unmetallized double-side TOPCon precursor, with an excellent implied open-circuit voltage of 730 mV and implied fill factor of ~86 %. However, the metalized J0 increased and contact resistivity decreased monotonically with the increase in the firing temperature. The 2D device simulations revealed that these layers can produce screen-printed DS-TOPCon cells with an efficiency of ~22.5 %. Solar cell modeling also showed that the DS-TOPCon solar cell efficiency can reach 24.1 % by decreasing the n-TOPCon thickness to 20 nm and lowering the full area metalized J 0 to ~100 mA/cm 2 .
Cubic-phase In{sub 2}O{sub 3} films are produced by the autowave oxidation reaction. Electron microscopy and photoelectron spectroscopy of the atomic profiles show that the samples are homogeneous over the entire area and throughout the thickness, with the typical grain size being 20-40 nm. The optical and electrical properties are studied for In{sub 2}O{sub 3} films fabricated at different pressures in the vacuum chamber. In the wave-length range from 400 to 1100 nm, the transparency of the films was higher than 85%; the resistivity of the films was 1.8 Multiplication-Sign 10{sup -2} {Omega} cm.
Rare-earth iron oxides (RFe{sub 2}O{sub 4}) have attracting attention as new electronic device materials because of their numerous functionalities, such as electronic ferroelectricity, ferrimagnetism, and high infrared absorption. In this paper, nearly monophasic Y bFe{sub 2}O{sub 4} films were prepared on α-Al{sub 2}O{sub 3}(001) substrates by the spin coating method using an aqueous-based Y bFe{sub 2}O{sub 4} solution. The solution was composed of a stoichiometric ratio of Y b(CH{sub 3}COO){sub 3} and Fe(NO{sub 3}){sub 3} with excess chelating agents. After heat treatment above 800 °C, well-crystallized and highly (001)-oriented Y bFe{sub 2}O{sub 4} started to epitaxially form on the substrate under controlled oxygen partial pressure with H{sub 2}/CO{sub 2} gas mixtures. X-ray pole figure analysis confirmed the following epitaxial relationship: Y bFe{sub 2}O{sub 4}[100](001)//α-Al{sub 2}O{sub 3}[100](001). Moreover formation of an Fe{sub 3}O{sub 4} interracial layer between Y bFe{sub 2}O{sub 4} and α-Al{sub 2}O{sub 3} was detected by high-resolution transmission electron microscopy. Presence of the Fe{sub 3}O{sub 4} interracial layer seemed to release the lattice misfit with the substrate. The Fe{sup 2+}/Fe{sup 3+} ratio in the obtained Y bFe{sub 2}O{sub 4} films was nearly stoichiometric and the indirect bandgap assigned to Fe{sup 2+} → Fe{sup 3+} charge transfer excitation was found to be ∼0.4 eV by optical spectroscopy. A clear magnetic transition from the paramagnetic state to the ferrimagnetic state occurred at ∼230 K.
The University of Puerto Rico-Rio Piedras Campus (UPR-RP) has been measuring aerosol optical, chemical, and microphysical properties at Cape San Juan (CSJ, also known as CPR) since 2004. This site has also hosted several intensive field campaigns, with context provided by the long-term measurements. Hurricane Maria largely destroyed the station on September 20, 2017, forcing a cessation of the measurements. The scientific focus of this intensive operational period was to use a U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Mobile Facility (AMF) aerosol shelter to enable the resumption of long-term aerosol measurements. This AMF shelter is now the main aerosol shelter for CSJ operations.
Development of polymer based mid-wavelength infrared (MWIR) optics has been limited mainly due to high optical loss of organic polymers used in general optical components. In this study, a MWIR polarization grating based on a sulfuric polymer poly(sulfur-random-(1,3-diisopropenylbenzene)) with a low loss in the MWIR range was fabricated using a simple two-step process: imprint and metal deposition. Fourier-transform infrared (FTIR) spectroscopy measurement showed that this polymeric MWIR polarizer selectively transmitted the polarized IR in transverse magnetic (TM) mode over the transverse electric (TE) mode at normal incidence. The measured extinction ratios ( η = The ratio of transmissions in TM and TE) were 208, 176, and 212 at the wavelength of 3, 4, and 5 μm, respectively. The computational simulation and analytical model confirmed that the enhanced TM transmission efficiency and η followed a Fabry-Pérot (FP) resonance mode within the created sulfuric polymer film. This polymeric MWIR polarizer demonstrated a great potential for broader applications in IR photonics to realize low-cost and durable optical components.
We perform a structural and optical characterization of InAs{sub 1-x}N{sub x} epilayers grown by molecular beam epitaxy on InAs substrates (x < or approx. 2.2%). High-resolution x-ray diffraction (HRXRD) is used to obtain information about the crystal quality and the strain state of the samples and to determine the N content of the films. The composition of two of the samples investigated is also obtained with time-of-flight secondary ion mass spectroscopy (ToF-SIMS) measurements. The combined analysis of the HRXRD and ToF-SIMS data suggests that the lattice parameter of InAsN might significantly deviate from Vegard's law. Raman scattering and far-infrared reflectivity measurements have been carried out to investigate the incorporation of N into the InAsN alloy. N-related local vibrational modes are detected in the samples with higher N content. The origin of the observed features is discussed. We study the compositional dependence of the room-temperature band gap energy of the InAsN alloy. For this purpose, photoluminescence and optical absorption measurements are presented. The results are analyzed in terms of the band-anticrossing (BAC) model. We find that the room-temperature coupling parameter for InAsN within the BAC model is C{sub NM}=2.0{+-}0.1 eV.
The optical constants of tantalum pentoxide (Ta{sub 2}O{sub 5}) are determined in a broad spectral region from the visible to the far infrared. Ta{sub 2}O{sub 5} films of various thicknesses from approximately 170 to 1600 nm are deposited using reactive magnetron sputtering on Si substrates. X-ray diffraction shows that the as-deposited films are amorphous, and annealing in air at 800 °C results in the formation of nanocrystalline Ta{sub 2}O{sub 5}. Ellipsometry is used to obtain the dispersion in the visible and near-infrared. Two Fourier-transform infrared spectrometers are used to measure the transmittance and reflectance at wavelengths from 1 to 1000 μm. The surface topography and microstructure of the samples are examined using atomic force microscopy, confocal microscopy, and scanning electron microscopy. Classical Lorentz oscillators are employed to model the absorption bands due to phonons and impurities. A simple model is introduced to account for light scattering in the annealed films, which contain micro-cracks. For the unannealed samples, an effective-medium approximation is used to take into account the adsorbed moisture in the film and a Drude free-electron term is also added to model the broad background absorption.
We report a giant enhancement of the midinfrared magneto-optical complex Kerr angle (polarization change of reflected light) in a variety of materials grown on SiC. In epitaxially grown multilayer graphene, the Kerr angle is enhanced by a factor of 68, which is in good agreement with Kerr signal modeling. Strong Kerr enhancement is also observed in Fe films grown on SiC and Al-doped bulk SiC. Our experiments and modeling indicate that the enhancement occurs at the high-energy edge of the SiC reststrahlen band where the real component of the complex refractive index n˜ passes through unity. Furthermore, since the signal is greatly enhanced when n˜ = 1, the enhancement is predicted to exist over the entire visible and IR spectrum for a free-standing film. We also predict similar giant enhancement in both Faraday (transmission) and Kerr rotation for thin films on a metamaterial substrate with refractive index n˜ = –1. Furthermore, this paper demonstrates that the substrate used in magneto-optical Kerr effect (MOKE) measurements must be carefully chosen when investigating magneto-optical materials with weak MOKE signals or when designing MOKE-based optoelectronic devices.
AERONET is an optical ground-based aerosol monitoring network and data archive supported by NASA's Earth Observing System and expanded by federation with many non-NASA institutions including AEROCAN (AERONET CANada) and PHOTON (PHOtometrie pour le Traiteinent Operatonnel de Normalisation Satellitaire). The network hardware consists of identical automatic sun-sky scanning spectral radiometers owned by national agencies and universities purchased for their own monitoring and research objectives. Data are transmitted hourly through the data collection system (DCS) on board the geostationary meteorological satellites GMS, GOES and METEOSAT and received in a common archive for daily processing utilizing a peer reviewed series of algorithms thus imposing a standardization and quality control of the product data base. Data from this collaboration provides globally distributed near real time observations of aerosol spectral optical depths, aerosol size distributions, and precipitable water in diverse aerosol regimes. Access to the AERONET data base has shifted from the interactive program 'demonstrat' (reserved for PI's) to the AERONET homepage allowing faster access and greater development for GIS object oriented retrievals and analysis with companion geocoded data sets from satellites, LIDAR and solar flux measurements for example. We feel that a significant yet under utilized component of the AERONET data base are inversion products made from hourly principal plane and almucanter measurements. The current inversions have been shown to retrieve aerosol volume size distributions. A significant enhancement to the inversion code has been developed and is presented in these proceedings.
A drifter equipped with bio-optical sensors and an automated water sampler was deployed twice, in 1987 and 1988, in the California Current as part of the Coastal Transition Zone program to study the biological, chemical, and physical dynamics of the meandering filaments observed off northern California.