Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Effect of heavy ion irradiation dose rate and temperature on α' precipitation in high purity Fe-18%Cr alloy

Cr-rich alpha prime precipitates (CrRP) induce hardening and embrittlement of FeCr alloys, but the kinetics of CrRP formation due to particle irradiation are not well understood. In this study, Fe18wt.%Cr alloy in solid solution state and pre-aged to produce relatively coarse CrRP was irradiated with 8 MeV Fe ions. The irradiation conditions involved two midrange doses of 0.37 and 3.7 displacements per atom (dpa), a wide range of dose rates (10 -5 –10 -3 dpa/s) and temperatures (300–450 °C). The distributions of CrRP after irradiation were studied with atom probe tomography (APT). The critical irradiation conditions to suppress CrRP formation were identified as 300 °C and 10-3 dpa/s; CrRP formation occurred readily at lower dose rates or higher temperatures. From 0.37 to 3.7 dpa, CrRP were observed to slightly grow at 350 °C and strongly coarsen at 450 °C. Specimens with pre-existing CrRP evolved into a similar precipitate distribution as detected after ion irradiation on solution annealed specimens at 300–350 °C to 0.37 dpa, indicating that the precipitate microstructure approaches a quasi-equilibrium for doses <1 dpa. Limited shrinking of pre-existing CrRP was observed after irradiation at 450 °C to 0.37 dpa, indicating a higher recovery rate at this temperature. Additionally, the evolution of CrRP is quantitatively explained by employing corrections to the historic Nelson-Hudson-Mazey precipitate stability model, and a radiation modified precipitation mechanism is proposed to account for the competition between radiation enhanced diffusion and ballistic dissolution which results in the modifications on both size and solute concentration of CrRP.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multi-objective surrogate-assisted calibration of CPFEM models using macroscopic response and in situ EBSD measurements of grain reorientation trajectories

Crystal plasticity finite element method (CPFEM) models are widely used to simulate the deformation behaviour of polycrystalline materials, but their calibration is often limited by their high computational cost and the non-convexity of the optimisation landscape. Here, this study develops a multi-objective surrogate-assisted calibration workflow that couples a multi-objective genetic algorithm (MOGA) with an adaptively trained deep neural network (DNN) surrogate model to efficiently identify CPFEM parameters from experimental data. The workflow is demonstrated on three crystal plasticity (CP) formulations of increasing complexity — Voce hardening (VH), two-coefficient latent hardening (LH2), and six-coefficient latent hardening (LH6) — using in situ electron backscatter diffraction (EBSD) measurements of Alloy 617 under uniaxial tensile loading. The CPFEM models are calibrated against the experimentally observed stress–strain response and reorientation trajectories of eight grains, then validated against eight additional trajectories and overall texture evolution. Across the CP formulations, the macroscopic response was reproduced reliably, while differences emerged in the robustness and accuracy of the grain-scale predictions. Including grain reorientation trajectories in the multi-objective calibration improved texture evolution predictions and filtered out physically inconsistent parameter sets that can arise from calibrating against only the stress–strain data. The workflow also demonstrates good transferability of calibrated parameters from a low- to a high-fidelity microstructural model. These results provide practical guidance for integrating in situ microstructural data into CPFEM through efficient, repeatable, and physically meaningful multi-objective calibration.

Crystal plasticity finite element method↗
DOE OSTI2024

A non-isothermal breakage-damage model for plastic-bonded granular materials incorporating temperature, pressure, and rate dependencies

Plastic-bonded granular materials (PBM) are widely used in industrial sectors, including building construction, abrasive applications, and defense applications such as plastic-bonded explosives. The mechanical behavior of PBM is highly nonlinear, irreversible, rate dependent, and temperature sensitive governed by various micromechanical attributions such as grain crushing and binder damage. This paper presents a thermodynamically consistent, microstructure-informed constitutive model to capture these characteristic behaviors of PBM. Key features of the model include a breakage internal variable to upscale the grain-scale information to the continuum level and to predict grain size evolution under mechanical loading. In addition, a damage internal state variable is introduced to account for the damage, deterioration, and debonding of the binder matrix upon loading. Temperature is taken as a fundamental external state variable to handle non-isothermal loading paths. The proposed model is able to capture with good accuracy several important aspects of the mechanical properties of PBM, such as pressure-dependent elasticity, pressure-dependent yield strength, brittle-to-ductile transition, temperature dependency, and rate dependency in the post-yielding regime. Furthermore, the model is validated against multiple published datasets obtained from confined and unconfined compression tests, covering various PBM compositions, confining pressures, temperatures, and strain rates.

Breakage↗
DOE OSTI2019

Electrochemically-Driven Phase Transformations in Battery Compounds (Final Technical Report)

Ion-insertion compounds for advanced batteries frequently exhibit phase transformations as the concentration of the working ion varies. Under the large electrochemical driving forces inherent to practical use, systems are often driven far from equilibrium and exhibit phase transition behavior not seen in other materials. An improved understanding of phase transformation pathways in electrode materials upon cycling will lead to new materials design concepts and electrochemical duty cycle management strategies that improve capacity utilization at high charge/discharge rates, reduce voltage and capacity hysteresis, and extend battery life. The main goal of this project is to develop a predictive understanding of the phase transition behavior of battery compounds when electrochemically driven far from equilibrium through a combined experimental- theoretical approach. Research focuses on elucidating how the phase transition behaviors in a diverse group of selected model systems (olivines, lithium metal, etc.) are regulated by various factors including transformation strains, plasticity, metastable transformation pathways, electrode microstructure, surface reaction and ion diffusion kinetics, and what are the unique features of phase transitions in battery compounds. To this end, operando X-ray-based characterization techniques are applied to interrogate the structure and composition evolution of electrode materials and interfaces at nano- and meso-scales. Mesoscale modeling techniques such as phase-field simulation are employed to shed light on the experimental observations and establish a unified framework for describing phase transition behaviors in battery compounds.

25 ENERGY STORAGE↗
DOE OSTI2023

Probing corrosion using a simple and versatile in situ multimodal corrosion measurement system

In this work, we have developed a unique in situ multimodal corrosion system that is capable of acquiring electrochemical data, sample imaging/visualization and hydrogen collection, simultaneously. Each of these modalities yield valuable information pertaining to the ongoing corrosion process. Combining them can yield holistic information on the role of microstructure, processing history, presence of coatings, etc., on the sequence of steps occurring during the corrosion process, and how they correlate with the acquired electrochemical data. Four materials systems, namely AA6061-T6 aluminum alloy, AZ91 magnesium alloy, galvanized DP590 steel, and pure Zn, were investigated under open circuit potential and under potentiodynamic polarization. The multimodal corrosion system was utilized to observe processes such as surface passivation and dissolution, pit and filiform corrosion initiation and propagation, and was correlated with location and magnitude of hydrogen evolution. This approach is shown to yield a truly multimodal understanding of the ongoing corrosion processes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Rheo-electric measurements of carbon black suspensions containing polyvinylidene difluoride in N -methyl-2-pyrrolidone

Lithium-ion battery cathode slurries have a microstructure that depends sensitively on how they are processed due to carbon black's (CB) evolving structure when subjected coating flows. While polyvinylidene difluoride (PVDF), one of the main components of the cathode slurry, plays an important role in modifying the structure and rheology of CB, a quantitative understanding is lacking. In this work, we explore the role of PVDF in determining the structural evolution of Super C65 CB in N-methyl-2-pyrrolidinone (NMP) with rheo-electric measurements. We find that PVDF enhances the viscosity of NMP resulting in a more extensive structural erosion of CB agglomerates with increasing polymer concentration and molecular weight. We also show that the relative viscosity of all suspensions can be collapsed by the fluid Mason number (Mnf), which compares the hydrodynamic forces imposed by the medium to cohesive forces holding CB agglomerates together. Using simultaneous rheo-electric measurements, we find at high Mnf, the dielectric strength (Δε) scales with Mnf, and the power-law scaling can be quantitatively predicted by considering the self-similar break up of CB agglomerates. The collapse of the relative viscosity and scaling of Δε both suggest that PVDF increases the hydrodynamic force of the suspending medium without directly changing the CB agglomerate structure. These findings are valuable for optimizing the rheology of lithium ion battery cathode slurries. We also anticipate that these findings can be extended to understand the microstructure of similar systems under flow.

Mechanics↗
DOE OSTI2023

Nanotwin stability in alloyed copper under ambient and cryo-temperature dependent deformation states

Nanometer size grains, solid solution strengthening, low temperatures, and a high density of nanotwins can provide significant strengthening to a material. Nevertheless, under loading the microstructure may evolve altering the effect of grain size, twin density, etc. on this strengthening. In some cases, these effects can be coupled as in detwinning, which is a mechanism for cryogenic grain growth. Here, in this work, a series of copper nanotwinned columnar grains are solid solution alloyed with aluminum and subject to ambient and cryogenic (–196 °C) environments during mechanical indentation, with the influence of alloying on the detwinning evolution studied. Under indentation, at a lower aluminum solute content (2 at.%), the columnar grains bent corresponding to a loss of twins. At a higher aluminum solute content (8 at.%), the grains shear and retain the nanotwins. Atomistic-scale simulations reveal an increase in the incoherent twin boundary velocity with decreasing temperature, but this boundary velocity is reduced with increasing alloy solute content. The coupling of solid solution strengthening and nanotwin stabilization is then used to explain the microstructural stability as a function of indentation at different temperature conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

In situ melt pool measurements for laser powder bed fusion using multi sensing and correlation analysis

Laser powder bed fusion is a promising technology for local deposition and microstructure control, but it suffers from defects such as delamination and porosity due to the lack of understanding of melt pool dynamics. To study the fundamental behavior of the melt pool, both geometric and thermal sensing with high spatial and temporal resolutions are necessary. This work applies and integrates three advanced sensing technologies: synchrotron X-ray imaging, high-speed IR camera, and high-spatial-resolution IR camera to characterize the evolution of the melt pool shape, keyhole, vapor plume, and thermal evolution in Ti–6Al–4V and 410 stainless steel spot melt cases. Aside from presenting the sensing capability, this paper develops an effective algorithm for high-speed X-ray imaging data to identify melt pool geometries accurately. Preprocessing methods are also implemented for the IR data to estimate the emissivity value and extrapolate the saturated pixels. Quantifications on boundary velocities, melt pool dimensions, thermal gradients, and cooling rates are performed, enabling future comprehensive melt pool dynamics and microstructure analysis. The study discovers a strong correlation between the thermal and X-ray data, demonstrating the feasibility of using relatively cheap IR cameras to predict features that currently can only be captured using costly synchrotron X-ray imaging. Such correlation can be used for future thermal-based melt pool control and model validation.

47 OTHER INSTRUMENTATION↗
DOE OSTI2019

Type IV failure in weldment of creep resistant ferritic alloys: II. Creep fracture and lifetime prediction

The creep rupture behavior (Type IV failure) for weldments of creep strength enhanced ferritic steel is numerically analyzed, using an integrated microstructure- and micromechanics-based finite element model. To account for the large microstructure gradients across weldments, a two-dimensional digital microstructure is constructed based on the actual observed microstructure of ferritic steel weldment by using the Voronoi-tessellation method. According to the fracture mechanism studies and literature experimental observations, the Type IV failure is identified as an intergranular creep fracture in the fine-grained or intercritical heated affected zone (FGHAZ or ICHAZ). In the present study, the following micromechanics model is employed to determine the micromechanical and microstructural origins for the failure process above, accounting for the underlying physical fracture mechanisms at different length scales, including nucleation of grain boundary cavities, their growth by competition of grain boundary diffusion and grain interior creep, viscous grain boundary sliding, and the emergence of microcracks by coalescence and their evolution to the ultimate failure. The methodology demonstrates the capabilities in modeling the Type IV failure and providing quantitative creep rupture lifetime prediction which shows an excellent agreement with long-term creep experimental data for creep strength enhanced ferritic steels and their weldments. In particular, the drop-off in time to rupture at high temperatures and low stress levels in the creep rupture curves is quantitatively predicted, and the transition of failure mechanisms from creep-controlled to diffusion-controlled creep fracture mechanism is illustrated.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure of Si Crystals Subjected to Irradiation with High-Energy H{sup +} Ions and Heat Treatment by High-Resolution Three-Crystal X-Ray Diffraction and Transmission Electron Microscopy

The structural features of the formation of radiation defects in proton-implanted layers of silicon plates during their heat treatment have been studied. New data on the nature, the characteristics, and the microdefect concentration in Si crystals irradiated with protons with energies 100 + 200 + 300 keV with the total dose 2 × 10{sup 16} cm{sup –2} and the evolution of the defect structure during heat treatment have been obtained by high-resolution three-crystal X-ray diffraction and transmission electron microscopy over wide temperature range from 200 to 1100°C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Insight of BaCe 0.5 Fe 0.5 O 3– δ twin perovskite oxide composite for solid oxide electrochemical cells

One-pot synthesized twin perovskite oxide composite of BaCe 0.5 Fe 0.5 O 3–δ (BCF), comprising cubic and orthorhombic perovskite phases, shows triple-conducting properties for promising solid oxide electrochemical cells. Phase composition evolution of BCF under various conditions was systematically investigated, revealing that the cubic perovskite phase could be fully/partially reduced into the orthorhombic phase under certain conditions. The reduction happened between the two phases at the interface, leading to the microstructure change. As a result, the corresponding apparent conducting properties also changed due to the difference between predominant conduction properties for each phase. Based on the revealed phase composition, microstructure, and electrochemical properties changes, a deep understanding of BCF's application in different conditions (oxidizing atmospheres, reducing/oxidizing gradients, cathodic conditions, and anodic conditions) was achieved. Triple-conducting property (H + /O 2– /e – ), fast open-circuit voltage response (~16–~470 mV) for gradients change, and improved single-cell performance (~31% lower polarization resistance at 600°C) were comprehensively demonstrated. Besides, the performance was analyzed under anodic conditions, which showed that the microstructure and phase change significantly affected the anodic behavior.

08 HYDROGEN↗
DOE OSTI2025

Ta–Zr carbides: Synthesis advances via carbothermal reduction and defect evolution observed through transmission electron microscopy ion irradiation

The thermodynamic stability of six distinct compositions within the Zr—Ta—C ternary system is investigated in this study, marking the first report of their synthesis through carbothermic reduction in vacuum. A prolonged annealing process at 2200°C enabled high densification and phase equilibrium. Detailed phase identification and microstructural characterization through microscopy and X-ray diffraction techniques revealed clear compositional trends and stable phase formations. Two compositions ((Ta 0.2 Zr 0.8 )C 0.6 and (Ta 0.5 Zr 0.5 )C 1 ) were selected for ion irradiation experiments using 200 keV Kr + at 600°C—representing the first-ever irradiation study on the Zr—Ta—C system. The findings indicated defect accumulation and nanoscale cavity formation without any evidence of amorphization, highlighting the system's structural stability under irradiation. Together, the synthesis and irradiation results provide a basis for further investigation of the system and suggest its relevance for applications under extreme environments.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Statistical evaluation of microscale stress conditions leading to void nucleation in the weak shock regime

Here, we investigate the heterogeneity of the stress state driven by anisotropic deformation response at the single crystal level through five statistical volume element (SVE) calculations of polycrystalline BCC tantalum. This work focuses on grain boundaries as a prominent material defect type prone to void nucleation based upon experimental observations of predominantly intergranular void nucleation in this material. The SVEs are constructed to be statistically representative of larger volumes of material and are meshed such that mean and standard deviation of grain size and orientation information is reconstructed. The computational meshes feature hexahedral (brick) elements and smooth conformal grain boundaries where significant stress concentration is known to occur, a tail effect of interest in the extreme events process of dynamic ductile damage. An existing micromechanical crystallographic plasticity model shown to capture the single crystal behavior of BCC tantalum well is used to perform the polycrystal calculations. The model includes representation of the non-Schmid effect of non-planar screw dislocation kinetics in tantalum. A three-dimensional stress state time profile predicted by damage modeling of a flyer plate impact experiment is applied as boundary conditions to each SVE. Resulting grain boundary stress state statistics are strongly non-Gaussian. Significant structural evolution is observed within the compressive hold before unloading into tension in the stress profile. Strong angular dependence of grain boundary traction magnitude with shock direction is observed. Non-Schmid effects continue to suggest their influence on propensity of microstructural defect types to nucleate voids. A general void nucleation criterion is proposed using probability theory. The general framework is specified to polycrystalline BCC tantalum in the weak shock regime to include the SVE calculations and literature molecular dynamics calculations of grain boundary void nucleation strength. Probability density functions (PDFs) are used to describe the interaction between the local stress state heterogeneity and the distributed grain boundary void nucleation strength state. A causation entropy maximization procedure removes the requirement for ad hoc selection of a PDF functional form and provides a rigorous procedure for data-based PDF determination. The resulting physically informed PDF describes the spatial appearance frequency of nucleated voids as a function of applied macroscale pressure. Lower length scale physics are thus packaged in a precise and computationally efficient way to provide computational plasticity insight to macroscale dynamic ductile damage models.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermal stability of 3D interface Cu/Nb nanolaminates

Nanocrystalline alloys are promising structural materials yet lack thermal stability in many cases. Recent work shows that interface structure has an outsize effect on the thermal behavior of nanostructured alloys. Here, this work focuses on the role of controlled heterophase interface structure in the thermal evolution of model Cu/Nb nanolaminates. We introduce 3D interfaces containing nanoscale heterogeneities in all spatial dimensions between Cu and Nb, forming 3D Cu/Nb. TEM, nanoindentation, and DSC are used in tandem to establish thermal stability and to identify shifts in microstructure as a function of static annealing temperature. 3D interfaces are shown to survive annealing to 300 °C for 1 hr., while 3D Cu/Nb microstructure evolves to form low-density and voided regions correlating to the onset of layer pinch-off between 500 and 600 °C annealing temperatures. A diffusivity- and vacancy energetics-based mechanism is developed to explain void formation driven by 3D interface degradation at elevated temperature.

3D interfaces↗
DOE OSTI2026

Investigating shock-induced chemical reactions in Ni+Al multilayers: A continuum-based mesoscale approach with Arrhenius kinetics and artificial thermal conduction

A new continuum-based mesoscale modeling approach for shock-induced chemical reactions (SICRs) in Ni+Al multilayers is demonstrated in Sandia’s shock physics hydrocode, CTH. The approach utilizes Arrhenius-type kinetics and artificial thermal conduction. Our work builds upon previous efforts to parameterize equations of state for Ni x Al y [J. Appl. Phys. 137, 075102 (2025)], as well as simulations of inert shocks in realistic 2D microstructures [J. Appl. Phys. 137, 225301 (2025)]. To calibrate the reaction kinetics, pairs of the reaction coordinate, R′, vs time are extracted from the molecular dynamics (MD) literature. Here, the MD-informed kinetics are used to simulate the dynamic evolution of pressure and temperature in 2D mesoscale simulations. Overall, the MD-informed kinetics obtained for planar interfaces are too slow, as initial reaction is not observed on a nanosecond time scale. Even with quasi-periodic shock focusing leading to the formation of so-called “hot-spots,” the hot spots are unable to grow and coalesce using the fitted Arrhenius rate constants. However, by increasing the rate constants by two orders of magnitude, SICRs are observed at a shock pressure near 30 GPa, which is supported by experiments. Consequently, these mesoscale simulations suggest that unresolved shear-based mechanical mixing might possibly account for the discrepancies in kinetic rates, with shock-generated intense perturbations, interfacial vortical flows, and elevated temperatures serving as favorable reaction conditions. Future work will calibrate a shear-dependent reaction rate from the MD simulations with realistic interfaces that are wavy, diffuse, and disordered.

Kittell, David E. [Sandia National Laboratories (S↗
DOE OSTI2018

Effect of Boron Content on Microstructure, Mechanical Properties, and Oxidation Resistance of Mo-Si-B Composites

Mo-Si-B composites with boron content from 0 to 8 wt.% were prepared by spark plasma sintering using Mo, Si, and B elemental powders. The effects of boron content on the phase composition, mechanical properties, and high-temperature oxidation resistance of the Mo-Si-B composites were investigated. The results show the evolution of the major phase constitution of the composites with increasing boron content is in the following sequence: (MoSi{sub 2}, Mo{sub 5}Si{sub 3}) → (MoSi{sub 2}, Mo{sub 5}Si{sub 3}, Mo{sub 5}SiB{sub 2}) → (MoSi{sub 2}, MoB) → (MoSi{sub 2}, MoB, MoB{sub 2}). As the boron content increases, both the hardness and flexural strength of the composites increases, but the fracture toughness of the composites gradually decreases. The strengthening mechanisms for the composites are second-phase strengthening and grain refinement strengthening. However, the formation of brittle phases, i.e., Mo{sub 5}SiB{sub 2}, MoB, and MoB{sub 2}, reduces the toughness of the composites. In addition, since a dense barrier layer of SiO{sub 2}-B{sub 2}O{sub 3} formed on the surface of the composites inhibits the inward diffusion of oxygen, B-doped Mo-Si-B exhibits better oxidation resistance compared with non-doped composites.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Cluster Dynamics Simulations of Intra-Granular Fission Gas Bubble Size and Pressure Evolution in UO 2

Fission gases such as xenon (Xe) play a critical role in determining the behavior and response of nuclear fuel. Given that Xe has little solubility in UO 2 , it accumulates and forms bubbles, which significantly impact fuel performance. Intra- and inter-granular bubble nucleation and growth can lead to fuel swelling, and once bubbles interconnect at grain boundaries, fission gas can be released into the plenum. At low temperatures, limited uranium vacancy mobility can restrict swelling, therefore causing the bubbles to become highly pressurized. Consequently, this can induce micro-cracking, promote fission gas release (increasing the likelihood of cladding failure), and even lead to fuel pulverization under accident conditions such as a loss of coolant accident. As bubble evolution is strongly influenced by local temperature and fission rate, markedly different behavior occurs across the radial profile of the fuel pellet. Capturing the mechanisms that underpin bubble evolution is therefore important to predict these behaviors in the fuel. Previous models describing important mechanisms informed by lower length scale simulations have been developed under the NEAMS program. These can describe the evolution of a single bubble type (i.e., single value for radius and pressure) at each position in the pellet, for instance using the Centipede cluster dynamic code. However, in reality, a full distribution in bubble sizes and pressures exists within the microstructure at a given position in the pellet. To address this the cluster dynamics code Xolotl, which can predict Xe and vacancy phase space (i.e., bubble distributions) for intra-granular bubbles, has been used before. Prior work benchmarked the Xolotl code against the Centipede cluster dynamics code to ensure compatibility and to verify that mobile defect properties are adequately transferred between the two codes, along with some physics improvements. In this work, we go further by introducing a physics-based set of improvements that will allow us to accurately predict bubble size distributions and internal bubble pressures under representative UO 2 irradiation conditions. The improvements include (i) coupling bubble-defect reaction energies to a virial equation of state (EOS), (ii) including a bubble surface tension contribution, (iii) incorporating radiation-induced re-solution of Xe and vacancies, (iv) enabling pressure-driven dislocation loop punching through an effective emission of interstitial clusters informed by interstitial loop energetics, (v) accounting for radiation induced athermal diffusion of Xe, and (vi) implementing a Booth-type grain boundary sink representation for all mobile defects and defect clusters. After these modifications, we observe good agreement of Xolotl fission gas bubble size and concentration predictions with legacy experimental measurements. Additionally, it allows the distribution of Xe bubble pressures and radius to also be predicted and compared to data produced through the Advanced Fuels Campaign (AFC) program. Here, we have done this by running simulations under conditions similar to the AFC post-irradiation examination (PIE) samples irradiated at North Anna 2 light water reactor (LWR). Our results shows excellent agreement with these experimental measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Porosity evolution in proton irradiated microfine-grained POCO graphite

This work investigated the porosity evolution of POCO ZXF-5Q graphite that has been irradiated by 340 kW, 120 GeV protons inside NT02 target system in Fermilab's NuMI beamline. This POCO graphite has undergone direct bulk dimensional swelling at low dose irradiation and its local microstructural change is still not well-understood during this process. In this work, the (sub-) micrometre scale porosity from six locations across proton beam fluence and temperature gradients have been studied using focused ion beam-scanning electron microscopy (FIB-SEM) tomography. Here, a deep learning-based tomographic image segmentation technique has been established and implemented for porosity segmentation and quantification. It has been found that there is a decrease in the total volumetric percentage of the porosity at proton beam centre (~ 8 – 8.4 vol.%), by comparing to un-irradiated POCO (~ 12 – 13vol.%) and to beam 2σ and 5σ radii (~ 12vol.%). This decrease in porosity volume percentage was found to be caused by the reduction in pores with volumes > 0.1 μm 3 induced by material bulk dimensional swelling at proton beam centre area. The porosity reduction in relation to dimensional change and irradiation creep was discussed among with other contributing factors, and further investigations through well-controlled irradiation experiment are still needed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗