Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EXPERIMENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

NASA Bioculture System: From Experiment Definition to Flight Payload

Starting in 2015, the NASA Bioculture System will be available to the science community to conduct cell biology and microbiology experiments on ISS. The Bioculture System carries ten environmentally independent Cassettes, which house the experiments. The closed loop fluids flow path subsystem in each Cassette provides a perfusion-based method for maintain specimen cultures in a shear-free environment by using a biochamber based on porous hollow fiber bioreactor technology. Each Cassette contains an incubator and separate insulated refrigerator compartment for storage of media, samples, nutrients and additives. The hardware is capable of fully automated or manual specimen culturing and processing, including in-flight experiment initiation, sampling and fixation, up to BSL-2 specimen culturing, and the ability to up to 10 independent cultures in parallel for statistical analysis. The incubation and culturing of specimens in the Bioculture System is a departure from standard laboratory culturing methods. Therefore, it is critical that the PI has an understanding the pre-flight test required for successfully using the Bioculture System to conduct an on-orbit experiment. Overall, the PI will conduct a series of ground tests to define flight experiment and on-orbit implementation requirements, verify biocompatibility, and determine base bioreactor conditions. The ground test processes for the utilization of the Bioculture System, from experiment selection to flight, will be reviewed. Also, pre-flight test schedules and use of COTS ground test equipment (CellMax and FiberCell systems) and the Bioculture System will be discussed.

Bioculture System↗

Orion EFT-1 Catalytic Tile Experiment Overview and Flight Measurements

This paper describes the design and results of a surface catalysis flight experiment flown on the Orion Multipurpose Crew Vehicle during Exploration Flight Test 1 (EFT1). Similar to previous Space Shuttle catalytic tile experiments, the present test consisted of a highly catalytic coating applied to an instrumented TPS tile. However, the present catalytic tile experiment contained significantly more instrumentation in order to better resolve the heating overshoot caused by the change in surface catalytic efficiency at the interface between two distinct materials. In addition to collecting data with unprecedented spatial resolution of the "overshoot" phenomenon, the experiment was also designed to prove if such a catalytic overshoot would be seen in turbulent flow in high enthalpy regimes. A detailed discussion of the results obtained during EFT1 is presented, as well as the challenges associated with data interpretation of this experiment. Results of material testing carried out in support of this flight experiment are also shown. Finally, an inverse heat conduction technique is employed to reconstruct the flight environments at locations upstream and along the catalytic coating. The data and analysis presented in this work will greatly contribute to our understanding of the catalytic "overshoot" phenomenon, and have a significant impact on the design of future spacecraft.

Salazar, Giovanni↗

Observation Platform for Dynamic Biomedical and Biotechnology Experiments Using the International Space Station (ISS) Light Microscopy Module (LMM)

Techshot, Inc., has developed an observation platform for the LMM on the ISS that will enable biomedical and biotechnology experiments. The LMM Dynamic Stage consists of an electronics module and the first two of a planned suite of experiment modules. Specimens and reagent solutions can be injected into a small, hollow microscope slide-the heart of the innovation-via a combination of small reservoirs, pumps, and valves. A life science experiment module allows investigators to load up to two different fluids for on-orbit, real-time image cytometry. Fluids can be changed to initiate a process, fix biological samples, or retrieve suspended cells. A colloid science experiment module conducts microparticle and nanoparticle tests for investigation of colloid self-assembly phenomena. This module includes a hollow glass slide and heating elements for the creation of a thermal gradient from one end of the slide to the other. The electronics module supports both experiment modules and contains a unique illuminator/condenser for bright and dark field and phase contrast illumination, power supplies for two piezoelectric pumps, and controller boards for pumps and valves. This observation platform safely contains internal fluids and will greatly accelerate the research and development (R&D) cycle of numerous experiments, products, and services aboard the ISS.

Kurk, Michael A. (Andy)↗

Observation Platform for Dynamic Biomedical and Biotechnology Experiments Using the International Space Station (ISS) Light Microscopy Module (LMM)

Techshot, Inc., has developed an observation platform for the LMM on the ISS that will enable biomedical and biotechnology experiments. The LMM Dynamic Stage consists of an electronics module and the first two of a planned suite of experiment modules. Specimens and reagent solutions can be injected into a small, hollow microscope slide-the heart of the innovation-via a combination of small reservoirs, pumps, and valves. A life science experiment module allows investigators to load up to two different fluids for on-orbit, real-time image cytometry. Fluids can be changed to initiate a process, fix biological samples, or retrieve suspended cells. A colloid science experiment module conducts microparticle and nanoparticle tests for investigation of colloid self-assembly phenomena. This module includes a hollow glass slide and heating elements for the creation of a thermal gradient from one end of the slide to the other. The electronics module supports both experiment modules and contains a unique illuminator/condenser for bright and dark field and phase contrast illumination, power supplies for two piezoelectric pumps, and controller boards for pumps and valves. This observation platform safely contains internal fluids and will greatly accelerate the research and development (R&D) cycle of numerous experiments, products, and services aboard the ISS.

Kurk, Michael A. (Andy)↗

The MISSE-9 Polymers and Composites Experiment Being Flown on the MISSE-Flight Facility

Materials on the exterior of spacecraft in low Earth orbit (LEO) are subject to extremely harsh environmental conditions, including various forms of radiation (cosmic rays, ultraviolet, x-ray, and charged particle radiation), micrometeoroids and orbital debris, temperature extremes, thermal cycling, and atomic oxygen (AO). These environmental exposures can result in erosion, embrittlement and optical property degradation of susceptible materials, threatening spacecraft performance and durability. To increase our understanding of space environmental effects such as AO erosion and radiation induced embrittlement of spacecraft materials, NASA Glenn has developed a series of experiments flown as part of the Materials International Space Station Experiment (MISSE) missions on the exterior of the International Space Station (ISS). These experiments have provided critical LEO space environment durability data such as AO erosion yield values for many materials and mechanical properties changes after long term space exposure. In continuing these studies, a new Glenn experiment has been proposed, and accepted, for flight on the new MISSE-Flight Facility (MISSE-FF). This experiment is called the Polymers and Composites Experiment and it will be flown as part of the MISSE-9 mission, the inaugural mission of MISSE-FF. Figure 1 provides an artist rendition of MISSE-FF ISS external platform. The MISSE-FF is manifested for launch on SpaceX-13.

De Groh, Kim K.↗

MIP: the First ISRU Flight Experiment

The Mars ISPP Precursor, “MIP”, was a flight experiment on the 2001 Mars Surveyor Lander that was designed to demonstrate In-situ Propellant Production-- ISPP-- for the first time on Mars. The experiment was designed to show that it was possible to produce oxygen from the carbon dioxide atmosphere, and to demonstrate the individual technology components that would go into a full-scale production plant. The aimpoint of the oxygen production was to showcase the possibility of producing oxygen for use as rocket fuel, ultimately as an enabling technology for a future human expedition to Mars. The MIP team built and qualified flight hardware for the experiment to fly on the Surveyor-2001 lander, but following the failure of the 1999 Mars Polar Lander spacecraft, the Surveyor-2001 lander mission was cancelled, and the MIP experiment was never flown. The experience in building and testing the hardware did show that the carbon dioxide electrolysis process was feasible, and led to incorporation of in-situ propellant production into the NASA reference plans for human Mars missions. Twenty years later, the technology is flying to Mars in the form of the MOXIE experiment on the Perseverance rover.

Geoffrey A Landis↗

Novel Hardware for a Lunar Plant Experiment

We propose an experiment, LPX (Lunar plant growth experiment), on the surface of the Moon that will conduct a fundamental investigation into the response of the plant Arabidopsis to lunar gravity and lunar radiation. For statistical significance, we will include more than 50 seeds. The experiment begins after lunar landing with water added to the seed platform and continues for 10 days or more. The growth of the plants, reaching ~ 1 cm high with typically 3-4 leaves in 10 days, will be monitored by camera and the carbon dioxide in the sealed chamber also will be monitored. The hardware for the LPX is based on proven technology flown on the ISS in Dec 2019 (Kitto et al. 2021, Life Sci. Space Res. in press) and the “Phytofuge” canister for Techshot MVP (Multi-use Variable-gravity Platform) centrifuge – both on ISS now. Both of these systems are TRL 9. This approach will allow identical units to be sent to the Moon and to be flown on ISS - allowing direct comparisons to partial gravity experiments done on the ISS experiment. Germination and growth of Arabidopsis requires temperature range of 20–25°C with the optimum being 22–23°C (Shymanovich and Kiss 2020, Gravit. & Space Res., 8, 1-7). This level of thermal control is a challenge on a small lunar lander and is effectively set by the latitude of the landing site. Given the mass and power limitations on a small lander, and the internal power of the LPX (~ 5W) the landing site needs to be between 73° and 77° − for which the noon time lunar surface temperatures are +15°C and -3°C (Hurley et al. 2015, Icarus 255,159-163). Within this range the temperature can be set with a small thermostatically-controlled heater These proposed experiments would be the first to grow plants on another planet and would provide important insights in terms of growth of plants on the Moon as part of bioregenerative life support.

Christopher P Mckay↗

Characterization of Novel Spacecraft Materials aboard the Materials International Space Station Experiment-Flight Facility (Preliminary Results)

This work will encompass the preflight characterization of 15 novel and heritage materials currently under observation on the Materials International Space Station Experiment-Flight Facility (MISSE-FF). MISSE-FF has been upgraded to perform active reflectance measurements of the materials. Images taken in RGB/IR colors are compared to results from an extensive ground testing campaign to obtain quantitative on-orbit material evolution data. Identical materials samples are to be flown on the ram, wake, and zenith faces of MISSE-FF, enabling deconvolution of the energetic electron, proton, atomic oxygen, and ultraviolet damage pathways. Energy deposition from the space environment leads to chemical changes in the material that in turn alter the optical properties. The same chemical damage that manifests as changes in optical reflectance and absorptance also leads to changes in myriad physical properties such as mechanical strength, electrical conductivity, and chemical reactivity. Therefore, flight materials are able to be characterized based on their unique reflectance spectra by comparing on-orbit measurements of optical reflectance with extensive terrestrial experiments, which help to correlate changes in reflectance with respect to changes in other material properties. The MISSE program has been a part of the International Space Station National Laboratory for many years and has been instrumental in understanding space weather modification of material properties. However, MISSE-FF has been limited to passive experiments with only pre/post flight material studies possible. In advance of the MISSE-16 experiment, the flight facility has received a major upgrade to provide daily spectral observations by way of a RGB/IR camera and a tunable light source. The MISSE-16 mission launched in February 2022 and carries 15 material samples for 6 months of the low Earth orbital exposure. Identical materials samples are to be flown on the ram, wake, and zenith faces of MISSE-FF, enabling deconvolution of the energetic electron, proton, atomic oxygen, and ultraviolet damage pathways. This paper discusses the MISSE-16 experiment, highlights the first use of the facility upgrades, and presents results from the extensive preflight material characterization that includes directional hemispherical reflectance, bidirectional reflectance, AFM, SEM, and electrical conductivity. Additionally, data showing the modification of these properties by ground-based exposure to space-like electron and atomic oxygen flux will be discussed. Finally, updates on deployment and initial check-out of the experiment on MISSE-FF will be presented. It is the ultimate goal of this program to provide validation for the development of ground based space weather simulation facilities and techniques.

Ryan Hoffman↗

Optimization of detection sensitivity for a Fiber Optic Intrusion Detection System (FOIDS) using design of experiments.

The Fiber Optic Intrusion Detection System (FOIDS)1 is a physical security sensor deployed on fence lines to detect climb or cut intrusions by adversaries. Calibration of detection sensitivity can be time consuming because, for example, the FiberSenSys FD-332 has 32 settings that can be adjusted independently to provide a balance between a high probability of detection and a low nuisance alarm rate. Therefore, an efficient method of calibrating the FOIDS in the field, other than by trial and error, was needed. This study was conducted to: x Identify the most significant settings for controlling detection x Develop a way of predicting detection sensitivity for given settings x Develop a set of optimal settings for validation The Design of Experiments (DoE) 2-4 methodology was used to generate small, planned test matrixes, which could be statistically analyzed to yield more information from the test data. Design of Experiments is a statistical methodology for quickly optimizing performance of systems with measurable input and output variables. DoE was used to design custom screening experiments based on 11 FOIDS settings believed to have the most affect on WKH types of fence perimeter intrusions were evaluated: simulated cut intrusions and actual climb intrusions. Two slightly different two-level randomized fractional factorial designed experiment matrixes consisting of 16 unique experiments were performed in the field for each type of intrusion. Three repetitions were conducted for every cut test; two repetitions were conducted for every climb test. Total number of cut tests analyzed was 51; the total number of climb tests was 38. This paper discusses the results and benefits of using Design of Experiments (DoE) to calibrate and optimize the settings for a FOIDS sensor

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Disposition of transuranic residues from plutonium isentropic compression experiment (Pu-ICE) constucted at Z machine

In 1992, the U.S. Congress passed legislation to discontinue above- and below-ground testing of nuclear weapons. Because of this, the U.S. Department of Energy (DOE) must rely on laboratory experiments and computer-based calculations to verify the reliability of the nuclear stockpile. The Sandia National Laboratories/New Mexico (SNL/NM) Z machine was developed to support the science-based approach for mimicking nuclear explosions and stockpile stewardship. Plutonium (Pu) isotopes with greater than ninety-eight percent enrichment were used in the experiments. In May 2006, SNL/NM received authority that the Z Machine Isentropic Compression Experiments could commence. Los Alamos National Laboratory (LANL) provided the plutonium targets and loaded the target assemblies provided by SNL/NM. Three experiments were conducted from May through July 2006. The residues from each experiment, which weighed up to 913 pounds, were metallic and were packaged into a 55-gallon drum each. SNL/NM conducts the experiments and provides temporary storage for the drums until shipment to LANL for final waste certification for disposal at the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico. This paper presents a comprehensive approach for documenting generator knowledge for characterization of waste in cooperation with scientists at the two laboratories and addresses a variety of essential topics.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The E166 experiment: Development of an Undulator-Based Polarized Positron Source for the International Linear Collider

A longitudinal polarized positron beam is foreseen for the international linear collider (ILC). A proof-of-principle experiment has been performed in the final focus test beam at SLAC to demonstrate the production of polarized positrons for implementation at the ILC. The E166 experiment uses a 1 m long helical undulator in a 46.6 GeV electron beam to produce a few MeV photons with a high degree of circular polarization. These photons are then converted in a thin target to generate longitudinally polarized e{sup +} and e{sup -}. The positron polarization is measured using a Compton transmission polarimeter. The data analysis has shown asymmetries in the expected vicinity of 3.4% and {approx}1% for photons and positrons respectively and the expected positron longitudinal polarization is covering a range from 50% to 90%. The full exploitation of the physics potential of an international linear collider (ILC) will require the development of polarized positron beams. Having both e{sup +} and e{sup -} beams polarized will provide new insight into structures of couplings and thus give access to physics beyond the standard model [1]. The concept for a polarized positron source is based on circularly polarized photon sources. These photons are then converted to longitudinally polarized e{sup +} and e{sup -} pairs. While in an experiment at KEK [1a], Compton backscattering is used [2], the E166 experiment uses a helical undulator to produce polarized photons. An undulator-based positron source for the ILC has been proposed in [3,4]. The proposed scheme for an ILC positron source is illustrated in figure 1. In this scheme, a 150 GeV electron beam passes through a 120 m long helical undulator to produce an intense photon beam with a high degree of circular polarization. These photons are converted in a thin target to e{sup +} e{sup -} pairs. The polarized positrons are then collected, pre-accelerated to the damping ring and injected to the main linac. The E166 experiment is dedicated to test this concept of a helical-undulator-based polarized positron source for the ILC. The experiment was carried out at SLAC where it benefitted from the high quality electron beam in the final focus test beam (FFTB).

43 PARTICLE ACCELERATORS↗

Evaluation of Plutonium Hemisphere Critical Experiments Partially Reflected by Steel and Oil

A series of 15 critical experiments performed at the Rocky Flats Critical Mass Laboratory in the late 1960s were evaluated and then determined to represent acceptable benchmark experiments for the validation of calculational methods. This series of experiments was part of a larger set of experiments performed to evaluate operational safety margins at the Rocky Flats Plant. The experiments consisted of bare plutonium metal hemishells reflected by steel hemishells of increasing thickness and motor oil. The hemishell assembly was suspended within dual aluminum tanks. Criticality was achieved by pumping oil into the tanks such that effectively infinite reflection was achieved in all directions except directly above the assembly; then the critical oil height was recorded. The results of these experiments had been initially ignored because early computational methods had been inadequate to analyze partially-reflected configurations. The dominant uncertainties include the uncertainty in the average plutonium density and the composition of materials in the gaps between the plutonium hemishells. Simple and detailed benchmark models were developed. Eigenvalue calculations using MCNP5 and ENDF/B-VII.0 were within 2s of the benchmark values. This benchmark evaluation has been added to the ICSBEP Handbook.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Results from Plasma Wakefield Experiments at FACET

We report initial results of the Plasma Wakefield Acceleration (PWFA) Experiments performed at FACET - Facility for Advanced aCcelertor Experimental Tests at SLAC National Accelerator Laboratory. At FACET a 23 GeV electron beam with 1.8 x 10{sup 10} electrons is compressed to 20 {mu}m longitudinally and focused down to 10 {mu}m x 10 {mu}m transverse spot size for user driven experiments. Construction of the FACET facility completed in May 2011 with a first run of user assisted commissioning throughout the summer. The first PWFA experiments will use single electron bunches combined with a high density lithium plasma to produce accelerating gradients > 10 GeV/m benchmarking the FACET beam and the newly installed experimental hardware. Future plans for further study of plasma wakefield acceleration will be reviewed. The experimental hardware and operation of the plasma heat-pipe oven have been successfully commissioned. Plasma wakefield acceleration was not observed because the electron bunch density was insufficient to ionize the lithium vapor. The remaining commissioning time in summer 2011 will be dedicated to delivering the FACET design parameters for the experimental programs which will begin in early 2012. PWFA experiments require the shorter bunches and smaller transverse sizes to create the plasma and drive large amplitude wakefields. Low emittance and high energy will minimize head erosion which was found to be a limiting factor in acceleration distance and energy gain. We will run the PWFA experiments with the design single bunch conditions in early 2012. Future PWFA experiments at FACET are discussed in [5][6] and include drive and witness bunch production for high energy beam manipulation, ramped bunch to optimize tranformer ratio, field-ionized cesium plasma, preionized plasmas, positron acceleration, etc.. We will install a notch collimator for two-bunch operation as well as new beam diagnostics such as the X-band TCAV [7] to resolve the two bunches. With these new instruments and desired beam parameters in place next year, we will be able to complete the studies of plasma wakefield acceleration in the next few years.

43 PARTICLE ACCELERATORS↗

Adaptation of existing facilities to isentropic compression experiments

We demonstrate that the established pulsed power infrastructure at the National High Magnetic Field Laboratory - Pulsed Field Facility (NHMFL-PFF) at the Los Alamos National Laboratory can be adapted to obtain high quality isentropic compression experiment (ICE) data on materials in extreme conditions of dynamic high pressure. Experiments utilized a single-turn magnet pulsed power system at the NHMFL-PFF that was originally designed to measure actinide samples in extremes of high magnetic field (to 300 Tesla). A simple modification to the single-turn magnet has converted it to a fast turnaround dynamic high pressure measurement system. This paper details the work done including important background details that indicate that much more can be accomplished with optimization of the load characteristics in terms of ultimate peak pressures. To match the rise time of the NHMFL capacitor bank ({approx}2 {mu}s versus {approx}0.5 {mu}s for the Sandia Z-machine) the sample dimensions can be relatively large, i.e., up to 5 mm thickness. The maximum stresses are {approx}50GPa (0.5 Mbar) at the maximum bank voltage (60 kV) and higher pressures may be possible if the sample is tamped. For the design and predictions of performance of the NHMFL-ICE experiment it is important to have good predictive models. A SPICE code simulation was chosen to model all aspects of the experiment, electrical and physical. To this end, accurate dynamic load models were developed to simulate the compression and expansion of the dynamic load at high pressures using shock physics principles. A series experiments have been performed which demonstrated the feasibility of the NHMFL-ICE technique. The results will be shown and discussed. The NHMFL-ICE technique is an excellent method for measuring equations of state (EOS) at megabar pressures. Because a complete EOS can be obtained in one experiment from zero to the peak pressure, and because many shots can be fired in one day, the technique promises to provide high quality EOS data at relatively low cost.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Fuel-Coolant Interaction Results for High Energy In-Pile LWR Fuels Experiments

Fuel-coolant interaction (FCI) has long been a subject of interest in severe-accident reactor safety applications. Significant chemical interaction also frequently results at the high temperature associated with these events in a water environment. Historical rapid, high energy transient irradiation test results are reviewed for experiments performed in transient experimental reactors in Idaho. Though such events are not credible for any deployed nuclear reactor technology, the pressure waves produced by FCI on surrounding containment structures are of importance to advanced light water reactor designs and for transient experiment design considerations. A brief introduction to steam explosion and related studies is provided in the context of these experiments. Extensive reactivity initiated accident testing programs were carried out in the Transient REActor Test (TREAT) facility, the Special Power Excursion Reactor Test (SPERT) facility, and the Power Burst Facility (PBF) from the 1960’s through the late 1970’s. A variety of fuel forms including waterlogged rods were tested in capsules containing water coolant at standard temperature pressure. A few tests were performed at high pressure and temperature in the water loop of PBF. In many of these experiments, energy deposition was high enough to greatly exceed melting temperatures of the fuel, resulting in some fraction of the fuel being dispersed into the coolant. A purpose of many of these tests was to determine the nuclear-to-mechanical energy conversion ratio as well as the extent of metal-water reaction. Relevant data collected from these tests included transient energy deposition, pressure response of the coolant, water column velocity, total hydrogen generation, and resulting particle size distributions and particle characterization. In this paper, the mechanical configuration of each experiment facility is reviewed and discussed relative to the measured responses. The empirical results for source pressure and extent of metal-water reaction are presented in the context of the experimental conditions. The results of these experiments provide a unique understanding for behavior of fuel under severe accident conditions in a reactor environment.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sequential Design of Experiments to Maximize Learning from Carbon Capture Pilot Plant Testing

Pilot plant test campaigns can be expensive and time-consuming. Therefore, it is of interest to maximize the amount of learning and the efficiency of the test campaign given the limited number of experiments that can be conducted. This work investigates the use of sequential design of experiments (SDOE) to overcome these challenges by demonstrating its usefulness for a recent solvent-based CO2 capture plant test campaign. Unlike traditional design of experiments methods, SDOE regularly uses information from ongoing experiments to determine the optimum locations in the design space for subsequent runs within the same experiment. However, there are challenges that need to be addressed, including reducing the high computational burden to efficiently update the model, and the need to incorporate the methodology into a computational tool. We address these challenges by applying SDOE in combination with a software tool, the Framework for Optimization, Quantification of Uncertainty and Surrogates (FOQUS) (Miller et al., 2014a, 2016, 2017). The results of applying SDOE on a pilot plant test campaign for CO2 capture suggests that relative to traditional design of experiments methods, SDOE can more effectively reduce the uncertainty of the model, thus decreasing technical risk. Future work includes integrating SDOE into FOQUS and using SDOE to support additional large-scale pilot plant test campaigns.

20 FOSSIL-FUELED POWER PLANTS↗

Bare, Complex, and Potassium-Filled HEU Oralloy Annuli Benchmark Experiments

Hundreds of critical experiments were constructed from Oak Ridge Alloy (oralloy) during the 1960s and 1970s at the Oak Ridge Critical Experiments Facility (ORCEF) in support of criticality safety operations at the Y-12 Plant. The purpose of these experiments included the evaluation of storage, casting, and handling limits and providing data for verification of calculation methods and cross sections for nuclear criticality safety applications. Recent contributions to the International Handbook of Evaluated Criticality Safety Benchmark Experiments (ICSBEP Handbook) include bare, complex, and potassium-filled annuli comprising multiple stacked units of highly enriched uranium (HEU), ~93.2 wt.% 235U, annuli, discs, and parallelepipeds. Prior contributions to the ICSBEP Handbook include bare (unreflected and unmoderated) cylinders; configurations of cylinders and annuli reflected with polyethylene, beryllium, or thin-graphite reflectors; GROTESQUE; and ORSphere. The newest contributions include a bare HEU 11-7 (11 inch outer diameter and 7 inch inner diameter) annulus capped at the top and bottom; bare HEU 13-7, 15-7, and 15-9 annuli; bare HEU complex annuli consisting of a 15-9 annulus containing either an off-center 7-inch-diameter cylinder, 5 × 5 inch parallelepiped, or split parallelepiped; and an HEU 13-7 annulus containing either empty stainless steel cans or potassium-metal-filled cans. The purpose of this latter pair of annulus configurations was to test the fast neutron cross sections of potassium as it was a candidate for coolant in some early space power reactor designs. A total of nine new configurations were evaluated as acceptable benchmark experiment measurements. Additional ORCEF oralloy experiments have also been identified for future benchmark evaluation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Advances and Enhancements in the Fabric for Frontier Experiments Project at Fermilab

The FabrIc for Frontier Experiments (FIFE) project within the Fermilab Scientific Computing Division is charged with integrating offline computing components into a common computing stack for the non-LHC Fermilab experiments, supporting experiment offline computing, and consulting on new, novel workflows. We will discuss the general FIFE onboarding strategy, the upgrades and enhancements in the FIFE toolset, and plans for the coming year. These enhancements include: expansion of opportunistic computing resources (including GPU and high-performance computing resources) available to experiments; assistance with commissioning computing resources at European sites for individual experiments; StashCache repositories for experiments; enhanced job monitoring tools; and a custom workflow management service. Additionally we have completed the first phase of a Federated Identity Management system to make it easier for FIFE users to access Fermilab computing resources.

Herner, Kenneth↗