Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data fitting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Absolute intensity measurements of CO2 bands in the 2395-2680/cm region

Absolute intensities for over 800 transitions belonging to twelve bands of (C-12)(O-16)2, (O-16)(C-12)(O-18), (O-16)(C-12)(O-17), and (O-16)(C-13)(O-18) molecules in the 2395-2680/cm spectral region have been derived using a nonlinear least-squares spectral fitting procedure. The data used in the analysis were recorded at room temperature and low pressure with the 0.01/cm resolution Fourier transform spectrometer in the McMath solar telescope complex at the National Solar Observatory. The measured intensities obtained for each band have been analyzed to derive the vibrational band intensity and F-factor coefficients. The results are compared with other published values.

Malathy Devi, V.↗

Pressure and temperature dependence of the reaction NO2 + NO3 + M yields N2O5 + M

The pressure and temperature dependences of the reaction NO2 + NO3 + M which yields N2O5 + M are investigated by using the flash photolysis/visible absorption technique in which the pseudo-first-order decay of NO3 is monitored as a function of total pressure (20-700 torr), diluent gas (M = He and N2), and temperature (236-358 K). The reaction is found to be in the falloff region in the 20-700 torr pressure range with collision efficiencies increasing in the order He less than N2. Falloff parameters are obtained by fitting the experimental data to the falloff equation of Troe and co-workers. The expression for k1(N2 concentration, T) is obtained and compared with the evaluations presented in the NASA (DeMore, 1983) and CODATA (Baulch et al., 1982) reviews of kinetic data for atmospheric chemistry. Both evaluations are based on N2O5 thermal decomposition data coupled with estimates of the equilibrium constant. The significance of the reactions for atmospheric chemistry rests not only on their rates but on the extent to which they result in a permanent sink for NOX.

Kircher, C. C.↗

The occultation of AG + 29 deg 398 by 93 Minerva

The occultation of AG + 29 deg 398 by 93 Minerva on 22 November 1982 was successfully observed at 10 sites. The data are best fitted by a circular limb profile having a diameter of 170.8 + or - 1.4 km, a value that agrees well with the published radiometric diameter for this asteroid. However, evidence of significant departure from a spherical shape is found in the occultation observations and in photometric measurements of Minerva made at Lowell Observatory over several months. Additional observations are needed to specify definitively the three-dimensional figure of Minerva.

Millis, R. L.↗

Spallogenic Be-10 in the Jilin chondrite

The Be-10 contents measured in eight bulk samples of the Jilin meteorite range from 5.05 + or - 0.55 to 16.3 + or - 1.7 dpm/kg, more than threefold, and correlate with the Ne-21 contents. A least-squares fit of these data has a positive intercept on the Be-10 axis which can be explained in terms of a two-stage irradiation. The second, more recent stage lasted 0.57 + or - 0.14 Myr. Model calculations give first-stage Be-10/Ne-21 age ranging from 6.2 to 7.1 Myr.

Pal, D. K.↗

X-ray spectrum and variability of 3C 120

The X-ray luminosity of 3C 120 is variable by a factor of 2.5 on time scales of days to months. The spectral slope of the 2-10 keV X-rays changes systematically in the sense that the higher intensity states are steeper. Simple power laws fitted to the data are consistent with an energy index alpha of 0.51 + or - 0.13 at minimum intensity and 0.83 + or - 0.03 at maximum, with a continuous variation in between. A more complicated spectral shape cannot be ruled out, but changes in absorbing column density alone cannot explain the data. The results are interpreted in terms of beamed synchrotron emission from a relativistic jet, a model which has been invoked previously for the spectra of BL Lac objects. The spectral variability is in marked contrast to the behavior of 3C 273, another superluminal source in which the X-ray spectral index is constant to a high degree of accuracy despite variability in time scales and amplitudes which are quite similar to those of 3C 120. The difference may be due to the degree of beaming of the respective core components. Another model which is consistent with the data involves thermal emission from isothermal shocks in a hot (approximately 10 to the 8th K) medium. Thermal Compton and spherical accretion X-ray source models do not reproduce the correct behavior of alpha versus flux.

Halpern, J. P.↗

Conformational properties, torsional potential, and vibrational force field for methacryloyl fluoride - An ab initio investigation

The structure, torsional potentials, vibrational spectra, and harmonic force fields for s-cis and s-trans isomers of methacryloyl fluoride are examined to understand the conformational properties of the molecules and their relationship to macroscopic polymer properties. The structure is found to be in good agreement with experiment. It is shown by calculations that the energy difference between the cis and the transisomers is less than 1 kcal/mol at both the split valence and the split valence polarized levels, with the trans form favored. Analysis of the torsional potentials indicates that a rigid rotor model provides a reasonable description of the motion of the COF group in the molecule. The torsional barrier to interconvert the s-trans to the s-cis form is found to be 7.0 kcal/mol. A fit of the data to a three-term Fourier series shows that it is possible to reproduce the experimentally derived barrier, even though a direct determination indicates that the barrier is higher.

Laskowski, B. C.↗

Precision ozone vapor pressure measurements

The vapor pressure above liquid ozone has been measured with a high accuracy over a temperature range of 85 to 95 K. At the boiling point of liquid argon (87.3 K) an ozone vapor pressure of 0.0403 Torr was obtained with an accuracy of + or - 0.7 percent. A least square fit of the data provided the Clausius-Clapeyron equation for liquid ozone; a latent heat of 82.7 cal/g was calculated. High-precision vapor pressure data are expected to aid research in atmospheric ozone measurements and in many laboratory ozone studies such as measurements of cross sections and reaction rates.

Hanson, D.↗

Role of long-wavelength degrees of freedom in the rod-to-coil transition in polymers

An analytical model is fitted to experimental data to show that rod-to-coil (RTC) transformations in single strand polymers (SSPs) are close to true phase transitions. The RTC are known to occur when the temperature or pH of a solvent in which the SSP is immersed is varied abruptly. Long wavelength degrees of freedom in the SSPs induce long range interactions in the molecule which lead to a first order phase transition. The Landau formalism suggests that a long-range ordered state can appear at a low temperature. A microscopic model of the phonon degrees of freedom identifies the nonzero temperature threshold at which the phase transition will occur. The phenomenology described is similar to a previous model for transitions in double-strand polymers.

Goldenfeld, N.↗

Mesospheric Winds at Jicamaraca, Peru (12 Deg S, 77 Deg SW), November 19-21, 1981

The altitude of mean zonal wind in the mesosphere during the whole daytime observations is given. Positive value refers to eastward. At around 70 km, wind corresponds to summer easterly, and changes to westerly with increasing altitude above about 77 km. These are fairly compatible with known features of zonal wind at this latitude. Contour plot shows local time variations of zonal wind with daytime mean subtracted and averaged over three days. Shaded area designated westward wind with contour level of 2 m/s. The daily variation is almost in phase with altitude in the 65 to 80 km region. Thus the semidiurnal tide with long vertical wavelength is inferred to exist. Above 80 km, phase tilt occurs which indicates the contribution of the propagating diurnal component. Here the combination of dc and 12-hr component is fitted to the data below 80 km. The altitude profiles of the amplitude and phase of this semidiurnal component are shown.

Aso, T.↗

The Jovian stratosphere in the ultraviolet

Models of the spectral reflectivity at the center of the disk of Jupiter from 1450 to 3150 angstroms are presented. The reflectivity was computed from 30 low-dispersion IUE spectra taken during the 1978-1980 solar maximum. A vertically inhomogeneous radiative transfer program was used to compute model reflectivities of various stratospheric compositions for comparison. Ammonia and acetylene are well determined because they show narrow absorption bands in the ultraviolet. Possible compositions to improve the fit to the data below 1800 angstroms are suggested. The data are too noisy to detect possible CO Cameron band absorption near 2000 angstroms.

Wagener, R.↗

Barrier height determination on Schottky contacts formed at the back contact-semiconductor interface of degraded solar cells

A method is described of determining an equivalent circuit for solar cells which have degraded as a result of the formation of a rectifying Schottky barrier at the back contact. An excellent fit of experimental data has been achieved using SCEPTRE with an equivalent circuit derived from the shape of the measured current voltage characteristics. One key parameter of the Schottky barrier diode, the reverse saturation current, can be used to determine the barrier potential. The barrier potential increases as the cell is stressed with 0.5 volts being a typical experimentally determined value for a degraded cell.

Misiakos, K.↗

Photometry of resolved galaxies. V - NGC 6822

Three-color CCD frames of the local group irregular galaxy NGC 6822 have been reduced to GRI photometry for 3475 stars using RICHFLD point-spread function fitting techniques. The data are compared with earlier work on this galaxy, particularly with Kayser (1966) on a star-by-star basis. Color-magnitude diagrams are constructed from the data and compared with both theoretical stellar model tracks and the expected foreground star contamination. A luminosity function for the blue stars is derived; comparison of this luminosity function with those of 10 other irregular galaxies indicates that NGC 6822 has a typical young star population. The stellar birthrate and initial mass function are estimated for this galaxy. The slope at the bright end of the mass function looks similar to recent results for the Galaxy, the Magellanic Clouds, and the irregular galaxy Sextans A. NGC 6822 appears to be presently forming stars at a slower rate for its mass than Sextans A or the Magellanic Clouds.

Hoessel, J. G.↗

Spectral rheology in a sphere

An earth model is considered whose rheology is described by a stress train relation similar to that which seems to fit the laboratory data resulting from constant strain rate and creep experiments on polycrystalline halite and granite. The response of the model to a surface load is studied. It is found that the displacement and the creep are weakly dependent on the wavenumber and that the strain energy is concentrated in the low wavenumber and coherent over large regions.

Caputo, M.↗

An analysis of the role of drift waves in equatorial spread F

An account is given of results of rocket measurements of the wave number spectrum of equatorial spread F irregularities, with emphasis on wavelengths less than 100 m. The measurements were made from two sounding rockets launched from Peru as part of Project Condor. The Condor density fluctuation spectra display a break at a wavelength near 100 m, identical to that found in the PLUMEX experiment (Kelley et al., 1982). The Condor data also confirm a subrange in which the density and the wave potential obey the Boltzmann relation - a strong indication of the presence of low-frequency electrostatic waves with finite wavelength parallel to the magnetic field, perhaps low-frequency drift waves as proposed by Kelley et al. The Condor data are also consistent with the previous conjecture that drift waves only exist above 300 km altitude. To investigate the difference in spectra observed over two altitude ranges, the data must be fitted to a form for the power spectrum taken from Keskinen and Ossakow (1981). The fitted spectrum, along with empirically determined growth and dissipation rates, is used to calculate the energy pumped into the spectrum at long wavelengths as well as the energy dissipated at shorter wavelengths. It is found that the energy is balanced by classical collisional effects in the low-altitude case, but energy balance in the high-altitude case requires an enhanced dissipation of about 500 times that due to classical diffusion. The model is consistent with, but does not uniquely imply, an inverse cascade of drift wave turbulence in equatorial spread F.

Labelle, J.↗

PTA test bed aircraft engine inlet model test report, revised

The inlet duct test for the Propfan Testbed Assessment (PTA) program was completed in November 1984. The basic test duct was designed using the Lockheed QUADPAN computational code. Test objectives were to experimentally evaluate, modify as required, and eventually verify satisfactory performance as well as duct/engine compatibility. Measured total pressure recovery for the basic duct was 0.993 with no swirl and 0.989 for inflow with a 30 degree simulated swirl angle. This compared to a predicted recovery of 0.979 with no swirl. Measured circumferential distortion with swirl, based on a least-square curve fit of the data, was 0.204 compared to a maximum allowable value of 0.550. Other measured distortion parameters did as well or better relative to their respective maximum allowable values. The basic duct configuration with no refinements is recommended for the PTA inlet as a minimum cost installation.

Hancock, J. P.↗

The identification of a distributed parameter model for a flexible structure

A computational method is developed for the estimation of parameters in a distributed model for a flexible structure. The structure we consider (part of the RPL experiment) consists of a cantilevered beam with a thruster and linear accelerometer at the free end. The thruster is fed by a pressurized hose whose horizontal motion effects the transverse vibration of the beam. The Euler-Bernoulli theory is used to model the vibration of the beam and treat the hose-thruster assembly as a lumped or point mass-dashpot-spring system at the tip. Using measurements of linear acceleration at the tip, it is estimated that the parameters (mass, stiffness, damping) and a Voight-Kelvin viscoelastic structural damping parameter for the beam using a least squares fit to the data. Spline based approximations to the hybrid (coupled ordinary and partial differential equations) system are considered; theoretical convergence results and numerical studies with both simulation and actual experimental data obtained from the structure are presented and discussed.

Banks, H. T.↗

A two-scale Bragg scattering model for microwave backscatter from wind generated waves

A model for the wavenumber spectrum for fully developed seas is derived as a function of the mean wind gradient. The high wavenumber part of the spectrum, which defines the Bragg wavenumbers, is an equilibrium spectrum in balance by a wind forcing term determined by viscous dissipation, which is a strong function of water temperature, and dissipation by breaking and microbreaking. The low wavenumber spectrum, constructed from surface elevation observations of gravity waves, is merged with the high wavenumber spectrum. Parameters are adjusted to fit circle flight data for Ku-band. The full spectrum is used in the two-scale Bragg scattering theory, plus specular reflection, to compute backscatter as a function of wind speed, direction, incidence angle, and water temperature (which determines viscosity) for Ku-band.

Donelan, M. A.↗

Solid lubrication design methodology, phase 2

The high temperature performance of solid lubricated rolling elements was conducted with a specially designed traction (friction) test apparatus. Graphite lubricants containing three additives (silver, phosphate glass, and zinc orthophosphate) were evaluated from room temperature to 540 C. Two hard coats were also evaluated. The evaluation of these lubricants, using a burnishing method of application, shows a reasonable transfer of lubricant and wear protection for short duration testing except in the 200 C temperature range. The graphite lubricants containing silver and zinc orthophosphate additives were more effective than the phosphate glass material over the test conditions examined. Traction coefficients ranged from a low of 0.07 to a high of 0.6. By curve fitting the traction data, empirical equations for slope and maximum traction coefficient as a function of contact pressure (P), rolling speed (U), and temperature (T) can be developed for each lubricant. A solid lubricant traction model was incorporated into an advanced bearing analysis code (SHABERTH). For comparison purposes, preliminary heat generation calculations were made for both oil and solid lubricated bearing operation. A preliminary analysis indicated a significantly higher heat generation for a solid lubricated ball bearing in a deep groove configuration. An analysis of a cylindrical roller bearing configuration showed a potential for a low friction solid lubricated bearing.

Pallini, R. A.↗