Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DAMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Effect of winglets on performance and handling qualities of general aviation aircraft

Recent flight and wind tunnel evaluations of winglets mounted on general aviation airplanes have shown improvements in cruise fuel efficiency, and climbing and turning performance. Some of these analyses have also uncovered various effects of winglets on airplane handling qualities. Retrofitting an airplane with winglets can result in reduced cross wind take-off and landing capabilities. Also, winglets can have a detrimental effect on the lateral directional response characteristics of aircraft which have a moderate to high level of adverse yaw due to aileron. Introduction of an aileron-rudder-interconnect, and reduction of the effective dihedral by canting-in of the winglets, or addition of a lower winglet can eliminate these flying quality problems.

Van Dam, C. P.↗

Effects of wingtip modifications on handling qualities of agricultural aircraft

The effect of wingtip modifications on the stability and control characteristics of an agricultural airplane has been studied by means of a nonplanar quasi-vortex-lattice method. The method is used to compute the changes in steady state and perturbed state lateral-directional stability and control derivatives produced by wingtip mounted winglets, vortex diffuser vanes, and tip extensions. The study shows that the combination of the excessive positive dihedral effect produced by the winglets and adverse yaw due to aileron deflection can have a detrimental effect on the roll control characteristics of the airplane. Introduction of an aileron-rudder-interconnect, and reduction of the effective dihedral by canting-in of the winglets, or addition of a lower winglet can eliminate the roll control problems.

Van Dam, C. P.↗

The design integration of wingtip devices for light general aviation aircraft

An investigation was conducted to determine the load carrying capabilities and structural design requirements for wingtip devices on general aviation aircraft. Winglets were designed and analyzed as part of a research program involving a typical agricultural aircraft. This effort involved analytical load prediction for the winglets, structural design for both the winglets and aircraft installation, structural load testing and flight test verification. Conclusions from this program are believed to be applicable to the use of wingtip devices on light-weight general aviation aircraft.

Gifford, R. V.↗

NASA aerial applications wake interaction research

A computer code has been developed for predicting trajectories of particles released in the wakes of airplanes or helicopters. The code accounts for effects of turbulence, crosswind, propeller slipstream, terrain variations, and plant canopy density on particle trajectories. Comparisons are given between experiments and theory. Applications of the code for spray pattern improvement are illustrated.

Morris, D. J.↗

NASA wake interactions research and applications

This report describes the development, validation, and application of a computer program for predicting trajectories and ground deposit patterns for particle released in the wakes of airplanes or helicopters. The computer program accounts for the effects of atmospheric turbulence, crosswind, propeller slipstream, terrain variations, evaporation, and plant canopy density on the particle trajectories. In order to validate the prediction method, some comparisons are shown between experimental data and theoretical predictions. Possible applications of the code for spray pattern improvement and for mission operations analysis are illustrated. In addition, the effect of winglets on pattern uniformity, drift, and airplane aerodynamics are presented.

Morris, D. J.↗

Shaping of airplane fuselages for minimum drag

The VSAERO surface panel method is employed to investigate fuselage shapes which can enhance the natural laminar flow (NLF) characteristics. The study is performed at cruise Re which are relevant to commuter, transport, and business aircraft. The technique is based on piecewise constant doublet and source singularities and takes into account the effects of compressibility. Inviscid pressure distributions were generated for five configurations to aid in the search for an optimized NLF body shape as a function of the transition locations and the drag coefficients. Granville's transition criteria are incorporated into the calculations to yield shapes with longer runs of laminar flow and reduced drag. In comparison with other transition prediction methods, the method described is shown to have significantly higher valicity for making three-dimensional transition predictions.

Dodbele, S. S.↗

Drag-reduction characteristics of aft-swept wing tips

Results are presented of a study conducted to analyze the potential aerodynamic improvements which can be obtained with aft-swept wing tips at subsonic speeds. A review and summary of previous swept-tip applications and studies are given. Additionally, the through evolution optimized tail-fin shapes of fast-cruising aquatic animals are examined as well as the wing planform shapes of sea birds. These superior long-distance travellers both display lifting-surface planform shapes with increased leading-edge sweep towards the tip. These observations and analytical results obtained with a nonlinear surface-panel method demonstrate that substantial induced-drag improvements can be obtained through the adoption of planform shapes with highly-tapered aft-swept tips.

Van Dam, C. P.↗

Swept wing-tip shapes for low-speed airplanes

Preliminary results are presented of a study conducted to analyze the effects of several plan-form modifications on the aerodynamic characteristics of a high-aspect-ratio, natural laminar flow (NLW) wing. The study addresses the potential aerodynamic improvements available at both cruise and high angles of attack by use os swept wing-tip shapes. The swept wing tip appears to offer a viable addition to the lift of wing-tip designs which provide improvements in aerodynamic efficiency, with the added safety benefit of providing high angle-of-attack departure resistance.

Van Dam, C. P.↗

Boundary-layer transition effects on airplane stability and control

Surface contamination of laminar-flow airfoils can significantly modify the location of transition from laminar-to-turbulent boundary-layer flow. The contamination can be the result of insect debris, environmental effects such as ice crystals and moisture due to mist or rain, surface damage, or other contamination adhering to the surface. Location and mode of transition have a dominant effect on the lift-and-drag characteristics of a lifting surface. The influences of laminar boundary-layer flow behavior on airplane stability and control are examined through theoretical results and experimental (wind-tunnel and free-flight) data. For certain airfoils with a relatively steep pressure recovery it is shown that loss of laminar flow near the leading edge can result in premature separation of the turbulent boundary layer and, consequently, in loss of lift and control effectiveness. Aerodynamic modifications which minimize boundary-layer transition effects on airplane stability and control are also discussed.

Van Dam, C. P.↗

Efficiency characteristics of crescent-shaped wings and caudal fins

Caudal (tail) fins of fish and aquatic mammals that cruise long distances, and wings of certain birds, often have the shape of a crescent moon. This study investigates how the crescent shape contributes to the traveling performance of these animals. A steady-flow theory (Maskew, 1982) that correctly models the trailing wake was used to analyze lifting surface efficiency, which is dependent on the level of induced (or vortex) drag for a given lift and span of the lifting surface. This analysis shows that backward curvature of a wing improves induced efficiency to a value greater than that of the flat untwisted wing of elliptical shape considered optimal in classical wing theory (Prandt, 1921 and Munk, 1921). This increase of induced efficiency results from the nonplanar trailing vortex sheet produced by the crescent-shaped wing at a given angle of attack.

Van Dam, C. P.↗

Displacements of the earth's surface due to atmospheric loading - Effects of gravity and baseline measurements

Atmospheric mass loads and deforms the earth's crust. By performing a convolution sum between daily, global barometric pressure data and mass loading Green's functions, the time dependent effects of atmospheric loading, including those associated with short-term synoptic storms, on surface point positioning measurements and surface gravity observations are estimated. The response for both an oceanless earth and an earth with an inverted barometer ocean is calculated. Load responses for near-coastal stations are significantly affected by the inclusion of an inverted barometer ocean. Peak-to-peak vertical displacements are frequently 15-20 mm with accompanying gravity perturbations of 3-6 micro Gal. Baseline changes can be as large as 20 mm or more. The perturbations are largest at higher latitudes and during winter months. These amplitudes are consistent with the results of Rabbel and Zschau (1985), who modeled synoptic pressure disturbances as Gaussian functions of radius around a central point. Deformation can be adequately computed using real pressure data from points within about 1000 km of the station. Knowledge of local pressure, alone, is not sufficient. Rabbel and Zschau's hypothesized corrections for these displacements, which use local pressure and the regionally averaged pressure, prove accurate at points well inland but are, in general, inadequate within a few hundred kilometers of the coast.

Van Dam, T. M.↗

Effects of compressibility on design of subsonic fuselages for natural laminar flow

Compressible linear boundary-layer stability analyses of two representative axisymmetric fuselage geometries indicate that a favorable effect will be exerted on the characteristics of a fuselage's axisymmetric boundary layer by compressibility. A freestream Mach number increase from 0.6 to 0.8 significantly reduces TS wave growth rates in the laminar boundary layer of the fuselages analyzed. The generally destabilizing effect of increasing length Re number on boundary layer stability can be overpowered by the favorable effects of compressibility on the fluid.

Vijgen, P. M. H. W.↗

Sheared wing-tip aerodynamics - Wind-tunnel and computational investigation

Computational and experimental performance benefits are presented for a high-aspect-ratio unswept wing configuration with sheared tips. The sheared tip is a highly swept and highly tapered surface located in the same plane as the inboard wing panel to which it is attached. The compuational results were obtained with an inviscid surface panel method that models the nonlinear influence of the trailing wake. Both wind-tunnel and calculated results were obtained for a 12-ft span wing model with various wing-tip configurations. The computational and experimental data are in fair agreement and demonstrate that sheared wing tips can reduce induced drag at cruise and climb lift coefficients. The drag reduction is the result of wake deformation effects and changes in spanwise load distribution. Wind-tunnel measured longitudinal and lateral directional stability characteristics are also presented for the various wing-tip layouts.

Vijgen, P. M. H. W.↗

Wind-tunnel investigations of wings with serrated sharp trailing edges

Exploratory wind-tunnel force measurements are presented for two wing geometries with small-scale planar and nonplanar serrated trailing-edge devices (chord-Reynolds numbers ranged from 1.0 to 3.7 million). The planar serrated trailing-edge extensions reduced the drag at conditions when trailing-edge separation occurred at low angles of attack. The introduction of serrations reduced or eliminated the drag penalty, due to the small (1-2 percent of the chord length) nonplanar trailing-edge flaps, while maintaining the effects of increase in camber. The presence of streamwise vortices immediately downstream of the serrated trailing edges is believed to have favorably affected the boundary-layer flow approaching the trailing edge and the near-wake development, resulting in reduced pressure (form) drag.

Vijgen, P. M. H. W.↗

High-alpha aerodynamic characteristics of crescent and elliptic wings

Static longitudinal and lateral-directional forces and moments were measured for elliptic- and crescent-wing models at high angles of attack in the NASA Langley 14-by-22-ft Subsonic Tunnel. The forces and moments were obtained for an angle-of-attack range including stall and post-stall conditions at a Reynolds number based on the average wing chord of about 1.8 million. Flow-visualization photographs using a mixture of oil and titanium-dioxide were also taken for several incidence angles. The force and moment data and the flow-visualization results indicated that the crescent wing model with its highly swept tips produced much better high-angle-of-attack aerodynamic characteristics than the elliptic model. Leading-edge separation-induced vortex flow over the highly swept tips of the crescent wing is thought to produce this improved behavior at high angles of attack. The unique planform design could result in safer and more efficient low-speed airplanes.

Van Dam, C. P.↗