Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPATIBILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Elastomer Swell Behavior in 1-Propanol, Diisobutylene, Cyclopentanone, and a Furan Mixture Blended in E10 and a Blendstock for Oxygenate Blending (BOB)

The compatibility of four potential bio-derived blendstock molecules with infrastructure elastomers was determined by measuring the volume change following exposure. The blendstock molecules included 1-propanol, diisobutylene, cyclopentanone, and a furan mixture. The elastomers included two fluorocarbons, six nitrile rubbers (NBRs), and one each of fluorosilicone, neoprene, polyurethane, and silicone. The elastomers were exposed to the fuel molecules as blends ranging from 0 to 30 vol.% in both a blendstock for oxygenate blending (BOB) formulation and an E10 fuel. Silicone exhibited excessive swelling in each test fuel, while the other elastomers showed good compatibility (low swell) with diisobutylene, 1-propanol, and the furan mixture when BOB was used as the base fuel. The E10 base fuel produced high (>30%) swell in neoprene, polyurethane, and some nitrile rubbers. In most cases diisobutylene produced the least amount of volume expansion. In contrast, the addition of cyclopentanone produced unacceptably high swelling in each elastomer and is not considered suitable for use with these fuels. Analysis of the results showed that the swelling behavior is predominantly due to the polarity of the elastomer and test fuels.

03 NATURAL GAS↗

Performance of Vehicle Fuel System Elastomers and Plastics with Test Fuels Representing Gasoline Blended with 10% Ethanol (E10) and 16% Isobutanol (iBu16)

The compatibilities of fuel system elastomers and plastics were evaluated for test fuels containing 16 vol.% isobutanol (iBu16) and 10 vol.% ethanol (E10). Elastomers included two fluorocarbons, four acrylonitrile butadiene rubbers (NBRs), and one type of fluorosilicone, neoprene, and epichlorohydrin/ethylene oxide. Plastic materials included four nylon grades, three polyamides, polytetrafluoroethylene (PTFE), polyvinylidene fluoride (PVDF), ethylene tetrafluoroethylene (ETFE), polyphenylene sulfide (PPS), high-density polyethylene (HDPE), polybutylene terephthalate (PBT), polyoxymethylene (POM), flexible polyvinylchloride (PVC), polyetherimide (PEI), polyetheretherketone (PEEK), and a phenol formaldehyde reinforced with glass fiber (GFPF). For each polymer material, the volume, mass, and hardness were measured before and after drying. Dynamic mechanical analysis (DMA) measurements were also performed on the dried specimens.For the elastomer materials the measured properties were similar for both fuels. The fluorocarbons and fluorosilicone swelled the least (~20%), while more moderate (20-45%) expansion occurred for the two NBR hose grades and (ECO). HNBR, neoprene, and silicone exhibited high swelling and softening, which likely precludes their use in many fuel systems. For the plastic materials, the observed swell was low; Nylon 11 swelled around 15%, but otherwise, their measured swell was <10%. Many of the plastics also showed sensitivity to alcohol type, as the E10 test fuel often imparted appreciably higher swell than iBu16. In general, the plastic materials showed good compatibility with the iBu16 and E10 test fuels. Here, the sole exception was the PVC material, which was structurally degraded from exposure to either fuel type. Compositional analysis showed high fuel retention in Nylon 12 and PVC. PVC also experienced a significant reduction in plasticizer compounds following exposure, which resulted in embrittlement and an increase in the glass-to-rubber transition temperature.

33 ADVANCED PROPULSION SYSTEMS↗

Promoted Combustion Behavior of 316 Stainless Steel and 6061 Aluminum Alloys in Elevated Pressure Nitrox Environments

Promoted combustion testing (outlined in the ASTM G124 “Standard Test Method for Determining the Combustion Behavior of Metallic Materials in Oxygen Enriched Atmospheres”) refers to a useful testing method to evaluate how metallic materials will behave when combusted in environments with high oxygen concentrations, elevated pressure, or both. These tests yield data which is useful for engineers and scientists from a variety of industries who need and rely on oxygen systems. Oxygen Compatibility Assessments (OCA’s) are vital for ensuring that materials will be safe for use, and these assessments rely on data from OCA’s or interpolation if a desired pressure/concentration is outside of previously tested bounds. It was identified that these bounds leave out significant areas of data for materials which are tested at high pressures (above 1500 psi) and variable oxygen concentrations (with nitrogen as the diluent gas). For this reason, the authors posited that conducting promoted combustion testing on materials above 1500 psi and in various concentrations of oxygen would be incredibly useful in future analyses for oxygen compatibility with similar environments (such as breathing air) as well as for further understanding of how materials behave at very high pressures (such as 10000 psi). Two materials were selected which are commonly used in industry today - 316 stainless steel and 6061 aluminum – and they were tested and analyzed for the purposes of this study.

oxygen compatibility↗

Hydrofluoroether (HFE) Cleaning Fluid Replacement and Qualification

This NASA Engineering and Safety Center (NESC) Technical Assessment Report addresses the urgent need to identify, test, and qualify replacement cleaning solvents and technologies following 3M’s decision to discontinue production of hydrofluoroether (HFE) products, including Novec HFE-7100, by the end of 2025. HFE-7100 is widely used across NASA for precision cleaning of ground and flight hardware, especially in oxygen system components, and as a heat transfer fluid in high-power-density thermal control systems. The assessment evaluates commercially available replacement solvents, alternative cleaning technologies, and their compatibility with NASA’s operational requirements. Key findings include the identification of viable solvent replacements, their performance in contaminant removal, materials compatibility, and oxygen system safety. The report also explores novel cleaning approaches, including aqueous, supercritical CO₂, cryogenic aerosol, plasma, UV-ozone, magnetically optimized fluids, and induced charge active filtration, highlighting their merits, limitations, and readiness for NASA adoption. The NESC provides recommendations for solvent selection, facility adaptation, and continued technology maturation to ensure mission continuity and regulatory compliance.

Alternative Cleaning Technologies↗

Considerations of Alloy N for Fluoride Salt-Cooled High-Temperature Reactor Applications

Fluoride Salt-Cooled High-Temperature Reactors (FHRs) are a promising new class of thermal-spectrum nuclear reactors. The reactor structural materials must possess high-temperature strength and chemical compatibility with the liquid fluoride salt as well as with a power cycle fluid such as supercritical water while remaining resistant to residual air within the containment. Alloy N was developed for use with liquid fluoride salts and it possesses adequate strength and chemical compatibility up to about 700 C. A distinctive property of FHRs is that their maximum allowable coolant temperature is restricted by their structural alloy maximum service temperature. As the reactor thermal efficiency directly increases with the maximum coolant temperature, higher temperature resistant alloys are strongly desired. This paper reviews the current status of Alloy N and its relevance to FHRs including its design principles, development history, high temperature strength, environmental resistance, metallurgical stability, component manufacturability, ASME codification status, and reactor service requirements. The review will identify issues and provide guidance for improving the alloy properties or implementing engineering solutions.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Development of Ceramic Interconnect Materials for SOFC

Currently, acceptor-doped lanthanum chromite is the state-of-the-art ceramic interconnect material for high temperature solid oxide fuel cells (SOFCs) due to its fairly good electronic conductivity and chemical stability in both oxidizing and reducing atmospheres, and thermal compatibility with other cell components. The major challenge for acceptor-doped lanthanum chromite for SOFC interconnect applications is its inferior sintering behavior in air, which has been attributed to the development of a thin layer of Cr2O3 at the interparticle necks during the initial stages of sintering. In addition, lanthanum chromite is reactive with YSZ electrolyte at high temperatures, forming a highly resistive lanthanum zirconate phase (La2Zr2O7), which further complicates co-firing processes. Acceptor-doped yttrium chromite is considered to be one of the promising alternatives to acceptor-doped lanthanum chromite because it is more stable with respect to the formation of hydroxides in SOFC operating conditions, and the formation of impurity phases can be effectively avoided at co-firing temperatures. In addition, calcium-doped yttrium chromite exhibits higher mechanical strength than lanthanum chromite-based materials. The major drawback of yttrium chromite is considered to be its lower electrical conductivity than lanthanum chromite. The properties of yttrium chromites could possibly be improved and optimized by partial substitution of chromium with various transition metals. During FY10, PNNL investigated the effect of various transition metal doping on chemical stability, sintering and thermal expansion behavior, microstructure, electronic and ionic conductivity, and chemical compatibility with other cell components to develop the optimized ceramic interconnect material.

30 DIRECT ENERGY CONVERSION↗

Detector Noise Susceptibility Issues for the Future Generation of High Energy Physics Experiments

The front-end electronics (FEE) noise characterization to electromagnetic interference and the compatibility of the different subsystems are important topics to consider for the LHC calorimeter upgrades. A new power distribution scheme based on switching power converters is under study and will define a noticeable noise source very close to the detector's FEE. Knowledge and experience with both FFE noise and electromagnetic compatibility (EMC) issues from previous detectors are important conditions to guarantee the design goals and the good functionality of the upgraded LHC detectors. This paper shows an overview of the noise susceptibility studies performed in different CMS subdetectors. The impact of different FEE topologies in the final sensitivity to electromagnetic interference of the subsystem is analyzed and design recommendations are presented to increase the EMC of the detectors to the future challenging power distribution topologies.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Investigation of Polyurethane and Fire-Retardant Foams as a Radiological Contamination Fixatives - 20202

Fixation of radiological contamination in decommissioning and deactivation can reduce worker risk, and mitigate potentially hazardous conditions; however, nearly every marketed contamination fixative has been found to be flammable, a significant concern in radiological facilities. Coupled with this, industry fixatives are normally used as a thin coating which can present problems when attempting to stabilize irregular void spaces or areas that are difficult to access and ensure full coverage. To this end, Savannah River National Laboratory (SRNL), in conjunction with Florida International University (FIU), have begun investigating the applicability of polyurethane based foaming materials, which will expand to fill a given asymmetric volume and provide fire retardancy to ensure no release of contamination in the event of a facility fire. Commercial foams undergo exothermic reactions resulting in gaseous release that subsequently causes the curing foam material to expand. Heat generation during curing can potentially compromise rubber parts of an enclosure, a significant concern in nuclear facilities. To mitigate large body heat generation, SRNL has also examined multiple layering of the material to ensure compatibility of the curing material with a previously cured body of the same material. Environmental studies were also completed in order to determine the influence on polyurethane based foams curing process. These studies showed that nearly half of the materials tested delaminated from a cured body of the same material, a property not discussed in commercially available documentation on the products. Of note was the compatibility of the foaming material with the substrate, depending on the type material that the foam was cured in/on, significant delamination could occur. Mechanical testing via tensile pull tester, dynamic mechanical analysis (DMA), and thermogravimetric analysis (TGA) was also performed. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

RH-TRU Waste Streams: HFDA Crucibles Create New Complex Waste Stream

This project focuses on the removal of the Hot Fuel Dissolution Apparatus (HFDA) crucibles from the Hot Fuel Examination Facility’s (HFEF) hot cells to create space for upcoming projects. The project team has created a crucible and pyro-salt non-debris waste stream that can be disposed of at Waste Isolation Pilot Plant (WIPP). Chemical Compatibility Examinations (CCEs) must be performed on candidate waste by reviewing the types of chemicals used in the experiments, information found in INL Process Knowledge Summary Reports (PKSRs), and Environmental Protection Agency guides on chemical compatibility. The CCEs identify which chemicals can be safely combined to ensure adverse reactions do not occur in the waste packages. The CCEs are then used to update the PKSR, Basis of Knowledge, and Acceptable Knowledge documents and demonstrate compliance with the WIPP Waste Acceptance Criteria. Once documents are finalized, they are reviewed and approved by the WIPP Central Characterization Project (CCP) to ensure proper waste stream characterization. After the documents are approved, the crucibles can be packaged and shipped to the Idaho Nuclear Technical and Engineering Center for storage awaiting certification. CCP will certify the waste using the approved documents and a series of confirmatory testing before being shipped and disposed in WIPP’s deep geological repository. Currently, the CCE is in progress and the PKSRs are being updated.

Basis of Knowledge↗

An Anisotropic Fluid-Solid Model of the Mouse Heart

A critical challenge in biomechanical simulations is the spatial discretization of complex fluid-solid geometries created from imaging. This is especially important when dealing with Lagrangian interfaces, as there must be at a minimum both geometric and topological compatibility between fluid and solid phases, with exact matching of the interfacial nodes being highly desirable. We have developed a solution to this problem and applied the approach to the creation of a 3D fluidsolid mesh of the mouse heart. First, a 50 micron isotropic MRI dataset of a perfusion-fixed mouse heart was segmented into blood, tissue, and background using a customized multimaterial connected fuzzy thresholding algorithm. Then, a multimaterial marching cubes algorithm was applied to produce two compatible isosurfaces, one for the blood-tissue boundary and one for the tissue-background boundary. A multimaterial smoothing algorithm that rigorously conserves volume for each phase simultaneously smoothed the isosurfaces. Next we applied novel automated meshing algorithms to generate anisotropic hybrid meshes with the number of layers and the desired element anisotropy for each material as the only input parameters. As the meshes are scale-invariant within a material and include boundary layer prisms, fluid-structure interaction computations would have a relative error equilibrated over the entire mesh. The resulting model is highly detailed mesh representation of the mouse heart, including features such as chordae and coronary vasculature, that is also maximally efficient to produce the best simulation results for the computational resources available

59 BASIC BIOLOGICAL SCIENCES↗

Wafer-Scale Single-Crystalline Ferroelectric Perovskite Nanorod Arrays

1D ferroelectric nanostructures are promising for enhanced ferroelectric and piezoelectric performance on the nanoscale but their synthesis at the wafer scale using industrially compatible processes is challenging. In order to advance the nanostructure-based electronics, it is imperative to develop a silicon-compatible growth technique yielding high volumetric density and an ordered arrangement. Here, a major breakthrough is provided in addressing this need and ordered and close-packed single crystalline ferroelectric nanorod arrays, of composition PbZr 0.52 Ti 0.48 O 3 (PZT), grown on commercial grade 3 in. silicon wafer are demonstrated. PZT nanorods exhibit enhanced piezoelectric and ferroelectric performance compared to thin films of similar dimensions. Sandwich structured architecture utilizing 1D PZT nanorod arrays and 2D reduced graphene oxide thin film electrodes is fabricated to provide electrical connection. Combined, these results offer a clear pathway toward integration of ferroelectric nanodevices with commercial silicon electronics.

36 MATERIALS SCIENCE↗

Hydrogen‐Bonded Polyimide/Metal‐Organic Framework Hybrid Membranes for Ultrafast Separations of Multiple Gas Pairs

Abstract Membranes have seen a growing role in mitigating the extensive energy used for gas separations. Further expanding their effectiveness in reducing the energy penalty requires a fast separation process via a facile technique readily integrated with industrial membrane formation platforms, which has remained a challenge. Here, an ultrapermeable polyimide/metal‐organic framework (MOF) hybrid membrane is reported, enabling ultrafast gas separations for multiple applications (e.g., CO 2 capture and hydrogen regeneration) while offering synthetic enhanced compatibility with the current membrane manufacturing processes. The membranes demonstrate a CO 2 and H 2 permeability of 2494 and 2932 Barrers, respectively, with a CO 2 /CH 4 , H 2 /CH 4 , and H 2 /N 2 selectivity of 29.3, 34.4, and 23.8, respectively, considerably surpassing the current Robeson permeability–selectivity upper bounds. At a MOF loading of 55 wt%, the membranes display a record‐high 16‐fold enhancement of H 2 permeability comparing with the neat polymer. With mild membrane processing conditions (e.g., a heating temperature less than 80 °C) and a performance continuously exceeding Robeson upper bounds for over 5300 h, the membranes exhibit enhanced compatibility with state‐of‐the‐art membrane manufacturing processes. This performance results from intimate interactions between the polymer and MOFs via extensive, direct hydrogen bonding. This design approach offers a new route to ultraproductive membrane materials for energy‐efficient gas separations.

Ma, Canghai↗

High-Power Lithium Metal Batteries Enabled by High-Concentration Acetonitrile-Based Electrolytes with Vinylene Carbonate Additive

To enable next-generation high power, high-energy-density lithium (Li) metal batteries (LMBs), an electrolyte possessing both high Li Coulombic efficiency (CE) at high-rate and good anodic stability on cathodes is critical. Acetonitrile (AN) is a well-known organic solvent for high anodic stability and high ionic conductivity, yet its application in LMBs is limited due to its poor compatibility with Li metal anode even at high salt concentration conditions. Here, we developed a highly concentrated AN-based electrolyte with vinylene carbonate (VC) additive to suppress Li+ depletion at high current densities. Addition of VC in the AN-based electrolyte leads to the formation of a polycarbonate-based solid electrolyte interphase which minimizes Li corrosion and leads to very high Li CE of up to 99.1% at a current density of 0.2 mA cm-2. Using such an electrolyte, fast charging of Li||NMC333 cells has been realized at a high current density of 3.6 mA cm-2, and stable cycling of Li||NMC622 cells with a high cathode loading of 4 mAh cm-2 has also been demonstrated.

Peng, Zhe↗

All Electrospray Printing of Carbon–Based Cost–Effective Perovskite Solar Cells

With the power conversion efficiencies of PSCs exceeding 25%, the perovskite solar cells (PSCs) are closer to step into the initial industrialization. Prior to transferring from laboratory fabrication to industrial manufacturing, issues such as scalability, materials cost, and production line compatibility that significantly impact the manufacturing remain to be addressed. Here we report breakthroughs on all these fronts. Carbon-based PSCs with architecture FTO/electron transport layer/perovskite/carbon, that eliminate the need for the hole transport layer and noble metal electrode, provide ultra-low-cost configuration. This PSC architecture was manufactured using a scalable and industrially compatible electrospray (ES) technique, which enables continuous printing of all the cell layers. The ES deposited electron transport layer and perovskite layer exhibited properties comparable to that of the laboratory-scale spin coating method. The ES deposited carbon electrode layer exhibited superior conductivity and interfacial microstructure in comparison to films synthesized using the conventional doctor blading technique. As a result, the fully ES printed carbon-based PSCs showed a record 14.41% power conversion efficiency, rivaling the state-of-the-art hole transporter-free PSCs. Furthermore, these results will immediately have an impact on the scalable production of PSCs.

14 SOLAR ENERGY↗

Enhanced Optical Contrast and Switching in Near‐Infrared Electrochromic Devices by Optimizing Conjugated Polymer Oligo(Ethylene Glycol) Sidechain Content and Gel Electrolyte Composition

Abstract A detailed investigation addressing the effects of functionalizing conjugated polymers with oligo(ethylene glycol) (EG n ) sidechains on the performance and polymer‐electrolyte compatibility of electrochromic devices (ECDs) is reported. The electrochemistry for a series of donor‐acceptor copolymers having near‐infrared (NIR)‐optical absorption, where the donor fragment is 3,4‐ethylenedioxythiophene (EDOT) or an EG n functionalized bithiophene (g2T) and the acceptor fragment is diketopyrrolopyrrole (DPP) functionalized with branched alkyl or EG n sidechains, is extensively probed. ECDs are next fabricated and it is found that EG n sidechain incorporation must be finely balanced to promote polymer‐electrolyte compatibility and provide efficient ion exchange. Proper electrolyte‐cation pairing and polymer structural tuning affords a 2x increase in optical contrast (from 12% to 24%) and >60x reduction in switching time (from 20 to 0.3 s). Atomic force microscopy (AFM)/grazing incidence wide‐angle X‐ray scattering (GIWAXS) characterization of the polymer film morphology/microstructure reveals that an over‐abundance of EG n sidechains generates large polymer crystallites, which can suppress ion exchange. Lastly, time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) indicates sidechain/electrolyte identity does not influence the electrolyte penetration depth into the films, and EG n sidechain inclusion increases electrolyte cation uptake. The material structural design insight and guidelines regarding the polymer‐electrolyte ion insertion/expulsion dynamics reported here should be of significant utility for developing next‐generation mixed ionic‐electronic conducting materials.

Chemistry↗

Enhancing Interconnect Reliability and Performance by Converting Tantalum to 2D Layered Tantalum Sulfide at Low Temperature

Abstract The interconnect half‐pitch size will reach ≈20 nm in the coming sub‐5 nm technology node. Meanwhile, the TaN/Ta (barrier/liner) bilayer stack has to be >4 nm to ensure acceptable liner and diffusion barrier properties. Since TaN/Ta occupy a significant portion of the interconnect cross‐section and they are much more resistive than Cu, the effective conductance of an ultrascaled interconnect will be compromised by the thick bilayer. Therefore, 2D layered materials have been explored as diffusion barrier alternatives. However, many of the proposed 2D barriers are prepared at too high temperatures to be compatible with the back‐end‐of‐line (BEOL) technology. In addition, as important as the diffusion barrier properties, the liner properties of 2D materials must be evaluated, which has not yet been pursued. Here, a 2D layered tantalum sulfide (TaS x ) with ≈1.5 nm thickness is developed to replace the conventional TaN/Ta bilayer. The TaS x ultrathin film is industry‐friendly, BEOL‐compatible, and can be directly prepared on dielectrics. The results show superior barrier/liner properties of TaS x compared to the TaN/Ta bilayer. This single‐stack material, serving as both a liner and a barrier, will enable continued scaling of interconnects beyond 5 nm node.

Lo, Chun‐Li↗

Dative Epitaxy of Commensurate Monocrystalline Covalent van der Waals Moiré Supercrystal

Realizing van der Waals (vdW) epitaxy in the 1980s represents a breakthrough that circumvents the stringent lattice matching and processing compatibility requirements in conventional covalent heteroepitaxy. However, due to the weak vdW interactions, there is little control over film qualities by the substrate. Typically, discrete domains with a spread of misorientation angles are formed, limiting the applicability of vdW epitaxy. In this study, the epitaxial growth of monocrystalline, covalent Cr 5 Te 8 2D crystals on monolayer vdW WSe 2 by chemical vapor deposition is reported, driven by interfacial dative bond formation. The lattice of Cr 5 Te 8 , with a lateral dimension of a few tens of micrometers, is fully commensurate with that of WSe 2 via 3 × 3 (Cr 5 Te 8 )/7 × 7 (WSe 2 ) supercell matching, forming a single-crystalline moiré superlattice. This work establishes a conceptually distinct paradigm of thin-film epitaxy, termed “dative epitaxy”, which takes full advantage of covalent epitaxy with chemical bonding for fixing the atomic registry and crystal orientation, while circumventing its stringent lattice matching and processing compatibility requirements; conversely, it ensures the full flexibility of vdW epitaxy, while avoiding its poor orientation control. Cr 5 Te 8 2D crystals grown by dative epitaxy exhibit square magnetic hysteresis, suggesting minimized interfacial defects that can serve as pinning sites.

36 MATERIALS SCIENCE↗