Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additively Manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Additively manufactured multiplexed inertial coalescence filters

Multiphase flows often pose a significant challenge to the efficient and reliable design of thermofluidic systems. This paper describes multiplexed inertial coalescence filters composed of parallel helical pathways, designed to capture fine droplets (<40 µm) through inertial separation while maintaining a low pressure drop (<400 Pa). Filtration efficiencies for 7 µm and 30 µm droplets were characterized for varying flow conditions, with complete capture observed above a threshold flow rate. Models for filtration efficiency and pressure drop were developed and validated against experimental results to allow system design and optimization, enabled by the tunable additive manufacturing approach used to fabricate the filters. Filter quality factor was computed for varying droplet sizes, showcasing exceptional quality factor when compared to state-of-the-art filters documented in the literature. In conclusion, this multiplexed inertial coalescence filtration approach could find use in dehumidification systems, fog harvesting, chemical reactors, and microgravity droplet capture.

3D Printing↗
DOE OSTI2020

Additive Manufacturing of Energy Harvesting Material System for Active Wireless MEMS Sensors

Combustion systems make up a large sum of the world’s yearly energy production despite advances in renewable energy sources. Precise control of pressure and temperature in combustion chambers allows for lower carbon emissions, and overall higher efficiency. Wireless temperature and pressure sensors are critical for the operation of combustion chambers. Energy harvesters have emerged as a viable way to power wireless sensors when heat and mechanical energy are available. Lithium niobate (LNB), barium titanate (BTO), and lead zirconate titanate (PZT) pyroelectric ceramics were studied and fabricated through additive manufacturing (AM) for use as energy harvesting structures in combustion environments. The electric power generation potential of LNB and PZT ceramics was studied by varying the temperature from 50 to 60 °C and by introducing cyclic compression loads of 2000 N amplitude. It was found that thermal energy conversion had the highest output of 500 nW and that combined thermal and mechanical conversion did not increase the harvesting potential because of the competing contributions of both effects. Powder bed and slurry extrusion AM methods were used to fabricate BTO and PZT ceramic structures. Optimization of the powder-based binder jetting method produced BTO ceramics with a relative density of 36.77% a piezoelectric coefficient of 153 pC/N. The density of the ceramics increased up to 56% when increasing the saturation of binder in the powder to because of liquid phase sintering. Finally, PZT structures were manufactured through AM and fin features were added to the design to enhance the heat transfer along the material. The harvested power density of the flat samples was 3.643 μW/cm 3 and of the finned samples was 3.034 μW/cm3. This research paves the ways for the development of self-powered wireless sensors in critical areas of operation such as combustion.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Wire Arc Additive Manufacturing of Multi-material Parts Using H-13 Tool Steel

H-13 tools steel’s relative hardness, resistance to thermal fatigue, and high tolerance of thermal shock, make it very desirable for use in forging, pressing, casting, and extrusion processes[1]. H-13 is however typically quite expensive when compared to many other steel compositions. It is therefore desirable to encase a lower cost steel composition with H-13. This configuration allows for the benefits of H-13 tooling to be realized, at a considerably reduced cost. To demonstrate the viability of this concept, a casting tool was fabricated using a Wire Arc Additive Manufacturing (WAAM) process. Initial materials testing was conducted on a multi-material wall which consisted of one section of H-13 tool steel, and one section of 410NiNmo. These tests included scanning electron microscopy, energy dispersive X-ray spectroscopy, and hardness testing. This testing generated favorable results and subsequently a casting tool was fabricated for evaluation. Utilization of a Multi-Material WAAM process to fabricate large tooling in this manner could yield significant improvements in material cost, manufacturing agility, and supply chain complexity.

Lambert, Nathan [ORNL] (ORCID:0009000324134206)↗
DOE OSTI2026

A synergistic approach to improve the cellulose nanofibril dispersion in poly(lactic acid) composites as feedstocks for extrusion-based additive manufacturing

Hybrid fiber-reinforced polymer composites (HFRPs) are multifunctional materials that bear more than one characteristic benefit. In this study, hybrid cellulose fibers, e.g., pulp fiber (PF) and cellulose nanofibril (CNF), were used for reinforcing poly(lactic acid) (PLA). A synergistic approach was applied to disperse CNF. The low-surface-tension solvent (ethanol), together with PF templating, assisted the dispersion of CNF in PLA. The HFRP achieved a higher tensile strength (∼70 MPa, 29% increase from PLA) and modulus (∼7 GPa, 46% increase from PLA), as well as a higher heat deflection temperature (∼60℃, 6℃ increase compared to neat PLA), compared to single-reinforcement FRPs. Additionally, the formulation was demonstrated to be potentially suitable for large-scale additive manufacturing.

Bista, Bivek [University of Maine]↗
DOE OSTI2020

Scalable Deep-Learning-Accelerated Topology Optimization for Additively Manufactured Materials

Topology optimization (TO) is a popular and powerful computational approach for designing novel structures, materials, and devices. Two computational challenges have limited the applicability of TO to a variety of industrial applications. First, a TO problem often involves a large number of design variables to guarantee sufficient expressive power. Second, many TO problems require a large number of expensive physical model simulations, and those simulations cannot be parallelized. To address these issues, we propose a general scalable deep-learning (DL) based TO framework, referred to as SDL-TO, which utilizes parallel schemes in high performance computing (HPC) to accelerate the TO process for designing additively manufactured (AM) materials. Unlike the existing studies of DL for TO, our framework accelerates TO by learning the iterative history data and simultaneously training on the mapping between the given design and its gradient. The surrogate gradient is learned by utilizing parallel computing on multiple CPUs incorporated with a distributed DL training on multiple GPUs. The learned TO gradient enables a fast online update scheme instead of an expensive update based on the physical simulator or solver. Using a local sampling strategy, we achieve to reduce the intrinsic high dimensionality of the design space and improve the training accuracy and the scalability of the SDL-TO framework. The method is demonstrated by benchmark examples and AM materials design for heat conduction. The proposed SDL-TO framework shows competitive performance compared to the baseline methods but significantly reduces the computational cost by a speed up of around 8.6x over the standard TO implementation.

Bi, Sirui↗
NASA NTRS2015

Printing Outside the Box: Additive Manufacturing Processes for Fabrication of Large Aerospace Structures

To achieve NASA's mission of space exploration, innovative manufacturing processes are being applied to the fabrication of propulsion elements. Liquid rocket engines (LREs) are comprised of a thrust chamber and nozzle extension as illustrated in figure 1 for the J2X upper stage engine. Development of the J2X engine, designed for the Ares I launch vehicle, is currently being incorporated on the Space Launch System. A nozzle extension is attached to the combustion chamber to obtain the expansion ratio needed to increase specific impulse. If the nozzle extension could be printed as one piece using free-form additive manufacturing (AM) processes, rather than the current method of forming welded parts, a considerable time savings could be realized. Not only would this provide a more homogenous microstructure than a welded structure, but could also greatly shorten the overall fabrication time. The main objective of this study is to fabricate test specimens using a pulsed arc source and solid wire as shown in figure 2. The mechanical properties of these specimens will be compared with those fabricated using the powder bed, selective laser melting technology at NASA Marshall Space Flight Center. As printed components become larger, maintaining a constant temperature during the build process becomes critical. This predictive capability will require modeling of the moving heat source as illustrated in figure 3. Predictive understanding of the heat profile will allow a constant temperature to be maintained as a function of height from substrate while printing complex shapes. In addition, to avoid slumping, this will also allow better control of the microstructural development and hence the properties. Figure 4 shows a preliminary comparison of the mechanical properties obtained.

Babai, Majid↗
NASA NTRSDate not supplied

Bridging the Gap Between Microscale Modeling and Additive Manufacturing for TPS

An overview of the now open-source NASA ARC software PuMA will be provided. On top of the well-documented ability to import and compute material properties from micro-CT images, PuMA has the ability to design microstructures and compute/predict material properties such as: porosity, permeability, tortuosity, thermal and electrical conductivity, tensile strength, etc. Therefore, a whole new range of capabilities is available, and provides users with the ability to build TPS materials (both fibrous and woven types) and optimize their properties based on missions and requirements. This talk will aim to provide a seed to start bridging the gap between microscale modeling of TPS materials and additive manufacturing.

Conductivity↗
DOE OSTI2022

Measurement of Convective Heat Transfer Coefficients with Supercritical CO2 in Novel Additively Manufactured Helically Patterned Pin Fin Tubes Using the Wilson Plot Technique

This paper describes the measurement of convective heat transfer coefficients and friction factors for sCO2 flowing in pin-fin patterned pipes in the Heat Exchange and Experimental Testing (HEET) facility at the US DoE’s National Energy Technology Laboratory (NETL) in Morgantown, WV. The measurement procedures in the HEET rig were validated by conducting benchmark tests with smooth stainless-steel tube and comparing the results with published correlations for Nusselt number (Nu) and friction factor. Over typical Reynolds number range in sCO2, the measured Nu and friction factors were within 7% of classical correlations for smooth tube flow.The candidate pin fin patterned pipes were additively manufactured (AM) at the Oak Ridge National Laboratory. The pins were circular or elliptical in cross-section. Pin length to diameter aspect ratios were 1.33 and 2, while the pin diameter to tube diameter ratio was 0.188 and 0.125. Tests were performed for ReD varying from 6.9×104 to 2.2×105 and at conditions equivalent to the low pressure outlet (8.69 MPa, 361 K) of the low temperature recuperator (LTR) in an indirect sCO2 power cycle. The Wilson plot technique was utilized to measure the bulk heat transfer coefficients.For the better performing design (tube A, pin length to tube diameter ratio: 1.33, pin diameter to tube diameter ratio: 0.188), the local heat transfer coefficient increased by 112% relative to the Dittus-Boelter correlation at the LTR low pressure outlet. This corresponded to a 282% increase in the product of the heat transfer coefficient and the surface area. Large pressure drops across the test articles were observed.

Searle, Matthew↗
DOE OSTI2022

Status of Additive Manufacturing Capabilities for Processing Refractory Alloys Under the Mo-99 Program

The enriched 100 Mo target, denoted as aMo, that Northstar Medical Radioisotopes is developing to produce 99 Mo from an accelerator-based method is a disk-type geometry with a 0.5–0.715 mm thickness and a 29 mm outer diameter. A press and sinter method was adopted to fabricate these samples from aMo powder feedstock. Inherent porosity from the press and sinter method makes the disks more easily dissolvable during 99 Mo postprocessing. However, the disk-type geometry will be subject to thermal stresses due to temperature variations once the geometry is in line with the accelerated electron beam, causing warping and possible failure. Additive manufacturing (AM) processes such as laser powder bed fusion (LPBF) enable the manufacturing of custom, complex geometries that may otherwise be difficult to produce with more conventional methods (e.g., press and sinter approach). Therefore, the National Nuclear Security Administration’s Molybdenum-99 Program invested in developing an AM facility dedicated to processing and printing refractory powders. This report details the LPBF process, how irregular refractory powder can be prepared for LPBF, and the equipment that is available to support the program.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Additive Manufacture of Porous ZrC for NTP In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Omar Mireles↗
DOE OSTI2020

Dissolution of Additively Manufactured Mo Disks and Structures for Accelerator Based Production of Mo-99

The press-and-sinter approach for production of Mo targets has been successfully tested and demonstrated. The main advantage of this process is that it uses readily available technology and tools that have been tuned for production of various metal and metal oxide targets. However, certain target design specifications, such as dimensional accuracy of the diameter and thickness of the disks, are required for proper fit into a target holder and therefore place strict tolerances on sintered Mo disks intended for accelerator production. Furthermore, having a target composed of multiple disks poses certain challenges for post-irradiation processing, where there is a potential for spillage of individual disks during the manipulation for dissolution inside a processing hot cell. Additive manufacturing (AM), also referred to as 3D printing, provides capabilities to design and build a single-piece Mo target that provides the opportunity for better geometry for optimized production of Mo-99, improved cooling capability, and safer post-irradiation handling. A drawback of AM Mo structures is roughness of finished surfaces, which could reduce the effectiveness of gas cooling systems. Process development for AM Mo structures using selective laser melting is described in work by Gibson and Lowden. For post-irradiation processing, it is important to look at the dissolution behavior of AM Mo structures in comparison to readily dissolved press-and-sinter Mo targets. The dissolution behavior of press-and-sinter targets has been well documented in our previous reports. In this report, we discuss results of dissolution experiments conducted with AM Mo disks and structures (provided by Oak Ridge National Laboratory [ORNL]) in 50% hydrogen peroxide (H 2 O 2 ).

36 MATERIALS SCIENCE↗
DOE OSTI2021

Predicting Pit Stability On Additively Manufactured SS316 Via Finite Element Modeling [Slides]

Pit growth and repassivation are complex, with many interconnecting geometric and environmental parameters to consider. Experimentally, it is difficult to isolate these individual parameters to study their effect on the stability of pits. To enable these studies, a finite element modeling approach has been developed to allow systematic testing of parameters that impact a pit’s stability. The specific parameters studied were the cathode diameter, the pit diameter and shape, and the water layer thickness. Hemispherical and rectangular-based pits were studied to determine the impact of the overall pit shape. Pit stability results were compared with mathematical calculations based on the Maximum Pit Model, for both 50% saturation and 100% saturated salt film coverage. Further studies expanded the range of pit geometry to those relevant to additively manufactured surfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Carbon Additive Manufacturing with a Near-Replica “Green-to-Brown” Transformation

Nanocomposites containing nanoscale materials offer exciting opportunities to encode nanoscale features into macroscale dimensions, which produces unprecedented impact in material design and application. However, conventional methods cannot process nanocomposites with a high particle loading, as well as nanocomposites with the ability to be tailored at multiple scales. A composite architected mesoscale process strategy that brings particle loading nanoscale materials combined with multiscale features including nanoscale manipulation, mesoscale architecture, and macroscale formation to create spatially programmed nanocomposites with high particle loading and multiscale tailorability is reported. The process features a low-shrinking (<10%) “green-to-brown” transformation, making a near-geometric replica of the 3D design to produce a “brown” part with full nanomaterials to allow further matrix infill. Here, this demonstration includes additively manufactured carbon nanocomposites containing carbon nanotubes (CNTs) and thermoset epoxy, leading to multiscale CNTs tailorability, performance improvement, and 3D complex geometry feasibility. The process can produce nanomaterial-assembled architectures with 3D geometry and multiscale features and can incorporate a wide range of matrix materials, such as polymers, metals, and ceramics, to fabricate nanocomposites for new device structures and applications.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Technology Drives Exploration: How NASA Is Embracing Additive Manufacturing

NASA has over 60 years of technology development that enabled human space and space science exploration “for the benefit of all humankind”. This presentation will start with the overview of NASA’s organization structure; the roles NASA’s leadership plays as well as 10 regional centers’ focused areas and capabilities. It will also highlight NASA’s Mission Directorates –Science, Human, Aeronautics, and Technology. With the onset of the newer and still evolving procurement business model (NASA being a buyer, instead of maker), a question remains: which is the right framework under which NASA can best integrate the capabilities of commercial, international, and other US government entities into a coherent exploration strategy? Another critical consideration is identifying which critical technologies to invest in NASA and which capabilities are better suited for commercialization as NASA as a buyer. Additive Manufacturing (AM) is certainly changing the space industry and providing new opportunities to travel to low earth orbit and explore our universe. New design opportunities –not previously possible –for new high performance metal alloys, light-weighting, managing thermal, structural, and dynamic loads are being enabled by AM. This presentation will showcase the vast portfolio of NASA’s AM activities in the last 13 years; transportation from Earth to Destination, Habitat at Destination, Lander from Station to Surface, and Science mission spacecrafts. NASA’s technical excellence is being leveraged heavily in the AM and Commercial Space community through collaborative projects, partnership agreements, tech transfer program. Examples of challenges of AM implementation as well as opportunities will be discussed.

Alison Park↗
DOE OSTI2023

High throughput structure–property relationship for additively manufactured 316L/IN625 alloy mixtures leveraging 2-step Bayesian estimation

While the fabrication of graded materials by directed energy deposition (DED) has led to accelerated materials discovery, the ability to rapidly explore sufficiently large material composition spaces is limited due to the time-intensive nature of conventional materials characterization techniques. The present study investigates the viability of small punch test (SPT) protocols for rapidly evaluating DED-fabricated alloy mixtures of stainless steel 316L (316L) and Inconel 625 (IN625). The SPT protocols evaluated in this study include both the recently established two-step Bayesian estimation framework as well as the empirical relationships established in prior literature. It is shown that these protocols are capable of reliably and quantitatively tracking the changes in the mechanical properties of the alloy mixtures studied. Enhancement of mechanical properties was observed with the addition of IN625 to 316L, which is attributed to the austenite stabilization in the matrix and the formation of fine δ - Ni3Nb precipitates. It is shown that CALPHAD-based Scheil model simulations predicted the formation of different precipitate phases for each composition. The novel protocols presented in this paper open new avenues for high throughput material explorations for additive manufacturing.

2-step Bayesian estimation↗