Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AERODYNAMICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Recent CFD Simulations of Shuttle Orbiter Contingency Abort Aerodynamics

Modern Computational Fluid Dynamics (CFD) techniques were used to compute aerodynamic forces and moments of the Space Shuttle Orbiter in specific portions of contingency abort trajectory space. The trajectory space covers a Mach number range of 3.5-15, an angle-of-attack range of 20-60 degrees, an altitude range of 100-190 kft, and several different settings of the control surfaces (elevons, body flap, and speed brake). While approximately 40 cases have been computed, only a sampling of the results is presented here. The computed results, in general, are in good agreement with the Orbiter Operational Aerodynamic Data Book (OADB) data (i.e., within the uncertainty bands) for almost all the cases. However, in a limited number of high angle-of-attack cases (at Mach 15), there are significant differences between the computed results, especially the vehicle pitching moment, and the OADB data. A preliminary analysis of the data from the CFD simulations at Mach 15 shows that these differences can be attributed to real-gas/Mach number effects.

Papadopoulos, Periklis↗

Numerical Simulation of Unsteady Aerodynamic Models

This report documents the results of the numerical simulations of unsteady aerodynamic models. The results focus on numerical accuracy and efficiency, and the robustness of the numerical methods. The aerodynamic models includes the classical Wagner and Kussner functions and the Leishman-Beddoes dynamic stall model. The simulations includes the numerical approximations of the Duhamel's integrals using both indicial (step) and impulse responses, the numerical integrations of the state-space models, and the exact solutions. The report also presents the conversion among different model representations.

Nguyen, Khanh Q.↗

Lobed Mixer Design for Noise Suppression: Plume, Aerodynamic and Acoustic Data

A comprehensive database for the acoustic and aerodynamic characteristics of several model-scale lobe mixers of bypass ratio 5 to 6 has been created for mixed jet speeds up to 1080 ft per s at typical take-off (TO) conditions of small-to-medium turbofan engines. The flight effect was simulated for Mach numbers up to 0.3. The static thrust performance and plume data were also obtained at typical TO and cruise conditions. The tests were done at NASA Lewis anechoic dome and ASE's FluiDyne Laboratories. The effect of several lobe mixer and nozzle parameters, such as, lobe scalloping, lobe count, lobe penetration and nozzle length was examined in terms of flyover noise at constant altitude and also noise in the reference frame of the nozzle. This volume is divided into three parts: in the first two parts, we collate the plume survey data in graphical form (line, contour and surface plots) and analyze it; in part 3, we tabulate the aerodynamic data for the acoustics tests and the acoustic data in one-third octave band levels.

Mengle, Vinod G.↗

Uncertainty in Computational Aerodynamics

An approach is presented to treat computational aerodynamics as a process, subject to the fundamental quality assurance principles of process control and process improvement. We consider several aspects affecting uncertainty for the computational aerodynamic process and present a set of stages to determine the level of management required to meet risk assumptions desired by the customer of the predictions.

Luckring, J. M.↗

Aerodynamic Shape Optimization Using Hybridized Differential Evolution

An aerodynamic shape optimization method that uses an evolutionary algorithm known at Differential Evolution (DE) in conjunction with various hybridization strategies is described. DE is a simple and robust evolutionary strategy that has been proven effective in determining the global optimum for several difficult optimization problems. Various hybridization strategies for DE are explored, including the use of neural networks as well as traditional local search methods. A Navier-Stokes solver is used to evaluate the various intermediate designs and provide inputs to the hybrid DE optimizer. The method is implemented on distributed parallel computers so that new designs can be obtained within reasonable turnaround times. Results are presented for the inverse design of a turbine airfoil from a modern jet engine. (The final paper will include at least one other aerodynamic design application). The capability of the method to search large design spaces and obtain the optimal airfoils in an automatic fashion is demonstrated.

Madavan, Nateri K.↗

Aerodynamics of Mars Odyssey

Direct Simulation Monte Carlo and free-molecular analyses were used to provide aerothermodynamic characteristics of the Mars Odyssey spacecraft. The results of these analyses were used to develop an aerodynamic database that was used extensively for the pre-flight planning and in-flight execution for the aerobraking phase of the Mars Odyssey mission. During aerobraking operations, the database was used to reconstruct atmospheric density profiles during each pass. The reconstructed data was used to update the atmospheric model, which was used to determine the strategy for subsequent aerobraking maneuvers. The aerodynamic database was also used together with data obtained from on-board accelerometers to reconstruct the spacecraft attitudes throughout each aerobraking pass. The reconstructed spacecraft attitudes are in good agreement with those determined by independent on-board inertial measurements for all aerobraking passes. The differences in the pitch attitudes are significantly less than the preflight uncertainties of +/-2.9%. The differences in the yaw attitudes are influenced by zonal winds. When latitudinal gradients of density are small, the differences in the yaw attitudes are significantly less than the preflight uncertainties.

Takashima, Naruhisa↗

Aerodynamic Database Development for Mars Smart Lander Vehicle Configurations

An aerodynamic database has been generated for the Mars Smart Lander Shelf-All configuration using computational fluid dynamics (CFD) simulations. Three different CFD codes, USM3D and FELISA, based on unstructured grid technology and LAURA, an established and validated structured CFD code, were used. As part of this database development, the results for the Mars continuum were validated with experimental data and comparisons made where applicable. The validation of USM3D and LAURA with the Unitary experimental data, the use of intermediate LAURA check analyses, as well as the validation of FELISA with the Mach 6 CF(sub 4) experimental data provided a higher confidence in the ability for CFD to provide aerodynamic data in order to determine the static trim characteristics for longitudinal stability. The analyses of the noncontinuum regime showed the existence of multiple trim angles of attack that can be unstable or stable trim points. This information is needed to design guidance controller throughout the trajectory.

Bobskill, Glenn J.↗

Uncertainty in Computational Aerodynamics

An approach is presented to treat computational aerodynamics as a process, subject to the fundamental quality assurance principles of process control and process improvement. We consider several aspects affecting uncertainty for the computational aerodynamic process and present a set of stages to determine the level of management required to meet risk assumptions desired by the customer of the predictions.

Luckring, J. M.↗

Some Effects of Nose Bluntness and Fineness Ratio on the Static Longitudinal Aerodynamic Characteristics of Bodies of Revolution at Subsonic Speeds

. The effects of a systematic variation of nose shape and fineness ratio on the longitudinal aerodynamic characteristics of bodies of revolution have been qualitatively determined at subsonic speeds. Six nose shapes were investigated, representing five corner radii which varied from 0 to 50 percent of the body diameter and three face radii which varied from 50 percent of the model diameter to infinity. The complete models had fineness ratios of 0.50 to 2.00. In addition, effects of boattailing the afterbody and removing or varying the transitions trips which had been attached to initiate a turbulent boundary layer were noted. Results are presented for an angle-of-attack range from -4 deg to 24 deg for Mach numbers from 0.25 to 0.80, and indicate that small variations of the model nose can produce large variations in the static longitudinal aerodynamic characteristics of the body. These variations may in turn be moderated by an increase in the model fineness ratio .

Hayes, William C., Jr.↗

Three-dimensional Aerodynamic Instability in Multi-stage Axial Compressors

Four separate tasks are reported. The first task: A Computational Model for Short Wavelength Stall Inception and Development In Multi-Stage Compressors; the second task: Three-dimensional Rotating Stall Inception and Effects of Rotating Tip Clearance Asymmetry in Axial Compressors; the third task:Development of an Effective Computational Methodology for Body Force Representation of High-speed Rotor 37; and the fourth task:Development of Circumferential Inlet Distortion through a Representative Eleven Stage High-speed axial compressor. The common theme that threaded throughout these four tasks is the conceptual framework that consists of quantifying flow processes at the fadcompressor blade passage level to define the compressor performance characteristics needed for addressing physical phenomena such compressor aerodynamic instability and compressor response to flow distoriton with length scales larger than compressor blade-to-blade spacing at the system level. The results from these two levels can be synthesized to: (1) simulate compressor aerodynamic instability inception local to a blade rotor tip and its development from a local flow event into the nonlinear limit cycle instability that involves the entire compressor as was demonstrated in the first task; (2) determine the conditions under which compressor stability assessment based on two-dimensional model may not be adequate and the effects of self-induced flow distortion on compressor stability limit as in the second task; (3) quantify multistage compressor response to inlet distortion in stagnation pressure as illustrated in the fourth task; and (4) elucidate its potential applicability for compressor map generation under uniform as well as non-uniform inlet flow given three-dimensional Navier-Stokes solution for each individual blade row as was demonstrated in the third task.

Suder, Kenneth↗

Wind Tunnel Measurements and Calculations of Aerodynamic Interactions Between Tiltrotor Aircraft

Wind tunnel measurements and calculations of the aerodynamic interactions between two tiltrotor aircraft in helicopter mode are presented. The measured results include the roll moment and thrust change on the downwind aircraft, as a function of the upwind aircraft position (longitudinal, lateral, and vertical). Magnitudes and locations of the largest interactions are identified. The calculated interactions generally match the measurements, with discrepancies attributed to the unsteadiness of the wake and aerodynamic forces on the airframe. To interpret the interactions in terms of control and power changes on the aircraft, additional calculations are presented for trimmed aircraft with gimballed rotors.

Johnson, Wayne↗

Aerodynamic Characteristics in Pitch and Sideslip of a 1/15-Scale Model of the Scout Vehicle at a Mach Number of 2.01

An investigation has been made t o determine the aerodynamic characteristics in pitch and sideslip of a 1/15-scale model of the Scout vehicle at a Mach number of 2.01. The effects of two sets of cruciform fins, of inline and indexed fin arrangements, a flare , and accessories such as antennas, launch fittings, and control tunnels were measured for combined angles of attack and sideslip to about 8deg. The tests were made in the Langley 4- by 4-foot supersonic pressure tunnel at a Reynolds number of 4 x 10(exp 6) per foot. The Addition of the rear fins or the flare increased the longitudinal and directional stability, whereas the front fins, either indexed or inline, had a destabilizing effect. All configurations became directionally unstable with increasing angle of attack. The accessories had only a small effect on the aerodynamic characteristics other than an increase in axial force.

Robinson, Ross B.↗

A Method for Obtaining the Nonlinear Aerodynamic Stability Characteristics of Bodies of Revolution from Free-Flight Tests

A method is presented for obtaining the nonlinear aerodynamic stability characteristics of bodies of revolution from free-flight test.s The necessary conditions for the application of this method are: (1) that the roll rate and damping encountered in a single cycle of oscillation be small, and (2) that the resulting motion be reasonably planar. Four approximations to the nonlinear restoring moment are considered and solutions are obtained in closed form: 1. A single-term polynomial in an arbitrary power of the angle of attack. 2. A two-term polynomial having linear and cubic terms. 3. A three-term polynomial having linear, quadratic, and cubic terms. 4. A three-term polynomial having linear, quadratic, and cubic terms. An iteration procedure is formulated to allow the use of each of these approximations for obtaining the aerodynamic coefficients of bodies of revolution from free-flight test data. It is found that although the equations that are solved pertain strictly to planar motion, the solutions are applicable to motions that deviate to a fairly large degree from planar motion.

Kirk, Donn B.↗

Transonic Aerodynamic Characteristics of a Wing-Body Combination having a 52.5 deg Sweptback Wing of Aspect Ratio 3 with Conical Camber and Designed for a Mach Number of the Square Root of 2

An investigation has been made of the effects of conical wing camber and supersonic body indentation on the aerodynamic characteristics of a wing-body configuration at transonic speeds. Wing aspect ratio was 3.0, taper ratio was 0.1, and quarter-chord line sweepback was 52.5 deg with airfoil sections of 0.03 thickness ratio. The tests were conducted in the Langley 16-foot transonic tunnel at various Mach numbers from 0.80 to 1.05 at angles of attack from -4 deg to 14 deg. The cambered-wing configuration achieved higher lift-drag ratios than a similar plane-wing configuration. The camber also reduced the effects of wing-tip flow separation on the aerodynamic characteristics. In general, no stability or trim changes below wing-tip flow separation resulted from the use of camber. The use of supersonic body indentation improved the lift-drag ratios at Mach numbers from 0.96 to 1.05.

Igoe, William B.↗

Aerodynamic Characteristics at Low Speed of a Reentry Configuration Having Rigid Retractable Conical Lifting Surfaces

An exploratory investigation has been made in the Langley 300 MPH 7 by 10 foot tunnel to study the low-speed static longitudinal and lateral stability characteristics of a reentry configuration having rigid retractable conical lifting surfaces that unfolded from the surface of a conical fuselage. The model also had curved tail surfaces that unfolded from a cylindrical aft section attached to the cone. Longitudinal tests were made through an angle-of-attack range from -4 deg to 90 deg and limited lateral tests were made through an angle-of-sideslip range from -12 deg to 32 deg at an angle of attack of 0 deg. The tail surface provided longitudinal trim to maximum lift and beyond and up to an angle of attack of 51 deg for a center-of-moment location of 42.9 percent mean aerodynamic chord. For this center-of-moment position the model had a static margin of 12 percent mean aerodynamic chord at the lower lift coefficients and was longitudinally stable up to a lift coefficient between 1.0 and 1.2. Neutral stability occurred from lift coefficient of 1.0 up to near maximum lift coefficient. The maximum value of trimmed lift-drag ratio was 4.85 at a lift coefficient of approximately 0.3 and a trimmed angle of attack of approximately 10 deg. The configuration was directionally stable throughout the test angle of sideslip range for an angle of attack of 0 deg.

Fournier, Paul G.↗

Aerodynamic Loads at Mach Numbers from 0.70 to 2.22 on a Airplane Model Having a Wing and Canard of Triangular Plan Form and Either Single or Twin Vertical Tails

Results of an investigation of the aerodynamic loads on a canard airplane model are presented without detailed analysis for the Mach number range of 0.70 t o 2.22. The model consisted of a triangular wing and canard of aspect ratio 2 mounted on a Sears-Haack body of fineness ratio 12.5 and either a single body-mounted vertical tail or twin wing mounted vertical tails of low aspect ratio and sweptback plan form. The body, right wing panel, single vertical tail, and left twin vertical tail were instrumented for measuring pressures. Data were obtained for angles of attack ranging from -4 degrees to +16 degrees, nominal canard deflection angles of 0 degrees and 10 degrees, and angles of sideslip of 0 degrees and 5.3 degrees. The Reynolds number was 2.9 x 10(exp 6) based on the wing mean aerodynamic chord. Selected portions of the data are presented in graphical form and attention is directed to some of the results of the investigation. All of the experimental results have been tabulated in the form of pressure coefficients and integrations of the pressure coefficients and are available as supplements to this paper. A brief summary of the contents of the tabular material is given.

Peterson, Victor L.↗

Aerodynamic Loads at Mach Numbers from 0.70 to 2.22 on an Airplane Model Having a Wing and Canard of Triangular Plan Form and Either Single or Twin Vertical Tails Supplement I-Tabulated Data for the Model with Single Vertical Tails: Tabulated Data for the Model with Single Vertical Tail - Supplement 1

Tabulated results of a wind-tunnel investigation of the aerodynamic loads on a canard airplane model with a single vertical tail are presented for Mach numbers from 0.70 to 2.22. The Reynolds number for the measurements was 2.9 x 10(exp 6) based on the wing mean aerodynamic chord. The results include local static pressure coefficients measured on the wing, body, and vertical tail for angles of attack from -4 deg to + 16 deg, angles of sideslip of 0 deg and 5.3 deg, vertical-tail settings of 0 deg and 5 deg, and nominal canard deflections of 0 deg and 10 deg. Also included are section force and moment coefficients obtained from integrations of the local pressures and model-component force and moment coefficients obtained from integrations of the section coefficients. Geometric details of the model and the locations of the pressure orifices are shown. An index to the data contained herein is presented and definitions of nomenclature are given.

Peterson, Victor L.↗

Investigation of the Aerodynamic Characteristics of Two Preliminary Designs of Scout Research Vehicle at Mach Numbers from 1.77 to 4.65

A wind-tunnel investigation has been conducted to determine the aerodynamic characteristics of two preliminary designs of the Scout research vehicle. The first model was tested at Mach numbers from 1.77 to 2.87 at Reynolds numbers of 3.7 x 10(exp 6) to 4.0 x 10(exp 6) per foot. A variable angle-of-attack range of -2 degrees to 14 degrees was used in determining the effect of nose shape, size of interstage flare base diameter, size of trapezoidal first-stage fins, and fin tip-control deflection on the aerodynamic characteristics of the model.

Keynton, Robert J.↗