SEARCH · Engineering Papers

Results for “static testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Data book for 12.5-inch diameter SRB thermal model water flotation test - 14.7 psia, series P024

Tests were conducted to determine how thermal conditions affect space shuttle solid rocket booster (SRB) flotation. Acceleration, pressure, and temperature data were recorded from initial water impact to final flotation position using a 12.5-inch diameter thermal model of the SRB at ambient pressure. The model was 136.9 inches long and weighed 117.3 lbm. The tests indicated the following differences from ambient temperature tests: (1) significant negative static pressures can occur during penetration; (2) maximum penetration is increased; and (3) final flotation is in the spar buoy mode.

Allums, S. L.↗

NASA NTRS1974

Aerodynamics of jet flap and rotating cylinder flap STOL concepts

The aerodynamic effectiveness of various propulsive lift concepts to provide for the low speed performance and control required for short takeoff and landing aircraft is discussed. The importance of the interrelationship between the propulsion system and aerodynamic components of the aircraft is stressed. The relative effectiveness of different lift concepts was evaluated through static and wind tunnel tests of various aerodynamic models and propulsion components, simulations of aircraft, and in some cases, flight testing of research aircraft incorporating the concepts under study. Results of large scale tests of lift augmentation devices are presented. The results of flight tests of STOL research aircraft with augmented jet flaps and rotating cylinder flaps are presented to show the steeper approach flight paths at low forward speeds.

Cook, W. L.↗

NASA NTRS1974

Data book for 12.5-inch diameter SRB thermal model water flotation test: 14.7 psia, series P020

Data acquired from the initial series of tests conducted to determine how thermal conditions affect SRB (Space Shuttle Solid Rocket Booster) flotation are presented. Acceleration, pressure, and temperature data recorded from initial water impact to final flotation position using a 12.5-inch diameter thermal model of the SRB at ambient pressure are included. The model was 136.9 inches long and weighed 117.3 lbm. The tests indicated the following differences from ambient temperature tests: (1) significant negative static pressures can occur during penetration; (2) maximum penetration is increased; and (3) final flotation is in the spar buoy mode.

Allums, S. L.↗

NASA NTRS1974

Investigation of fatigue strength of multilayer advanced fiber composites

The analytical characterization of a multilayer fiber composite plate (without hole) was accomplished for both static and dynamic loading conditions using the finite difference technique. Thornel 300/5208 composites with and without holes were subjected to static and tensile fatigue testing. Five (5) fiber orientations were submitted to test. Tensile fatigue testing also included three (3) loading conditions and two (2) frequencies. The low-cycle test specimens demonstrated a shorter tensile fatigue life than the high-cycle test specimens. Failure surfaces demonstrated effect of testing conditions. Secondary failure mechanisms, such as: delamination, fiber breakage, and edge fiber delamination were present. Longitudinal delamination between plies also occurred in these specimens.

Thornton, H. R.↗

NASA NTRS1975

Discussion of an aeromechanical gust alleviation system to improve the ride comfort of light airplanes

A discussion of an on-going NASA research project of a gust alleviation system to improve the ride comfort of a light airplane is presented. The discussion includes a description of the proposed system which uses auxiliary aerodynamic surfaces to drive the trailing-edge flaps. The results of analytical work on the effects of the system on stability and effectiveness of the system are presented. Static wind-tunnel tests of the system installed in a 1/6-scale model of a popular light airplane are also described. Problem areas which may need future investigation are discussed.

Stewart, E. C.↗

NASA NTRS1976

Machining titanium alloys

Study suggests ways of reducing chatte, increasing productivity, and reducing tool wear. Report also describes static and dynamic cutting tests and tool materials and finishes.

Sutherland, I. A.↗

NASA NTRS1976

Unsteady aerodynamic flow field analysis of the space shuttle configuration. Part 1: Orbiter aerodynamics

An analysis of the steady and unsteady aerodynamics of the space shuttle orbiter has been performed. It is shown that slender wing theory can be modified to account for the effect of Mach number and leading edge roundness on both attached and separated flow loads. The orbiter unsteady aerodynamics can be computed by defining two equivalent slender wings, one for attached flow loads and another for the vortex-induced loads. It is found that the orbiter is in the transonic speed region subject to vortex-shock-boundary layer interactions that cause highly nonlinear or discontinuous load changes which can endanger the structural integrity of the orbiter wing and possibly cause snap roll problems. It is presently impossible to simulate these interactions in a wind tunnel test even in the static case. Thus, a well planned combined analytic and experimental approach is needed to solve the problem.

Ericsson, L. E.↗

NASA NTRS1977

Systems for measuring response statistics of gigahertz bandwidth photomultipliers

New systems have been developed for measuring the average impulse response, the pulse-height spectrum, the transit-time statistics as a function of signal level, and the dark-count spectrum of gigahertz bandwidth photomultipliers. Measurements showed that the 0.53 microns pulse used as an optical test source had a 30 picoseconds and less than 70 ps pulse width. Calibration data showed the system resolution to be less than 20 ps for root mean square transit-time measurements. Test data for a static crossed-field photomultiplier showed 2-photoelectron resolution and less than 30-ps time jitter over the 1- to 100-photoelectron range.

Abshire, J. B.↗

NASA NTRS1978

Transonic static and dynamic stability characteristics of a finned projectile configuration

Static and dynamic stability tests were made of a finned projectile configuration with the aft-mounted fins arranged in a cruciform pattern. The tests were made at free stream Mach numbers of 0.7, 0.9, 1.1, and 1.2 in the Langley 8-foot transonic pressure tunnel. Some of the parameters measured during the tests were lift, drag, pitching moment, pitch damping, and roll damping. Configurations tested included the body with undeflected fins, the body with various fin deflections for control, and the body with fins removed. Theoretical estimates of the stability derivatives were made for the fins on configuration.

Boyden, R. P.↗

NASA NTRS1978

Variation of fan tone steadiness for several inflow conditions

An amplitude probability density function analysis technique for quantifying the degree of fan noise tone steadiness has been applied to data from a fan tested under a variety of inflow conditions. The test conditions included typical static operation, inflow control by a honeycomb/screen device and forward velocity in a wind tunnel simulating flight. The ratio of mean square sinusoidal-to-random signal content in the fundamental and second harmonic tones was found to vary by more than an order-of-magnitude. Some implications of these results concerning the nature of fan noise generation mechanisms are discussed.

Balombin, J. R.↗

NASA NTRS1977

Motion sickness and otolith sensitivity - A pilot study of habituation to linear acceleration

Astronauts, particularly in Skylab flights, experienced varying degrees of motion sickness lasting 3-5 days. One possible mechanism for this motion sickness adaptation is believed to be a reduction in otolith sensitivity with an attendant reduction in sensory conflict. In an attempt to determine if this hypothesis is valid, a ground-based pilot study was conducted on a vertical linear accelerator. The extent of habituation to accelerations which initially produced motion sickness was evaluated, along with the possible value of habituation training to minimize the space motion sickness problem. Results showed that habituation occurred for 6 of the 8 subjects tested. However, in tests designed to measure dynamic and static otolith function, no significant differences between pre- and post-habituation tests were observed. Cross habituation effects to a standard Coriolis acceleration test were not significant. It is unlikely that ground-based pre-habituation to linear accelerations of the type examined would alter susceptibility to space motion sickness.

Potvin, A. R.↗

NASA NTRS1978

Variation of fan tone steadiness for several inflow conditions

Balombin, J. R.↗

NASA NTRS1979

A method for predicting the noise levels of coannular jets with inverted velocity profiles

A coannular jet was equated with a single stream equivalent jet with the same mass flow, energy, and thrust. The acoustic characteristics of the coannular jet were then related to the acoustic characteristics of the single jet. Forward flight effects were included by incorporating a forward exponent, a Doppler amplification factor, and a Strouhal frequency shift. Model test data, including 48 static cases and 22 wind tunnel cases, were used to evaluate the prediction method. For the static cases and the low forward velocity wind tunnel cases, the spectral mean square pressure correlation coefficients were generally greater than 90 percent, and the spectral sound pressure level standard deviation were generally less than 3 decibels. The correlation coefficient and the standard deviation were not affected by changes in equivalent jet velocity. Limitations of the prediction method are also presented.

Russell, J. W.↗

NASA NTRS1979

Effects of fuselage forebody geometry on low-speed lateral-directional characteristics of twin-tail fighter model at high angles of attack

Low-speed, static wind-tunnel tests were conducted to explore the effects of fighter fuselage forebody geometry on lateral-directional characteristics at high angles of attack and to provide data for general design procedures. Effects of eight different forebody configurations and several add-on devices (e.g., nose strakes, boundary-layer trip wires, and nose booms) were investigated. Tests showed that forebody design features such as fineness ratio, cross-sectional shape, and add-on devices can have a significant influence on both lateral-directional and longitudinal aerodynamic stability. Several of the forebodies produced both lateral-directional symmetry and strong favorable changes in lateral-directional stability. However, the same results also indicated that such forebody designs can produce significant reductions in longitudinal stability near maximum lift and can significantly change the influence of other configuration variables. The addition of devices to highly tailored forebody designs also can significantly degrade the stability improvements provided by the clean forebody.

Carr, P. C.↗

NASA NTRS1982

Net shape fabrication of Alpha Silicon Carbide turbine components

Development of Alpha Silicon Carbide components by net shape fabrication techniques has continued in conjunction with several turbine engine programs. Progress in injection molding of simple parts has been extended to much larger components. Turbine rotors fabricated by a one piece molding have been successfully spin tested above design speeds. Static components weighing up to 4.5 kg and 33 cc in diameter have also been produced using this technique. Use of sintering fixtures significantly improves dimensional control. A new Si-SiC composite material has also been developed with average strengths up to 1000 MPa (150 ksi) at 1200 C.

Storm, R. S.↗

NASA NTRS1983

JT150 1/2-scale nozzle jet noise experiment and comparison with prediction

As part of a program to study flight effects on the exhaust noise of a full scale JT15D engine, static half scale model jet noise experiments were conducted. Acoustic data were recorded for microphone angles of 45 deg to 155 deg with jet conditions for the model scale nozzle corresponding closely to those at 55, 73 and 97 percent of corrected rated speed for the full scale engine. These data are useful for determining the relative importance of jet and core noise in the static full scale engine test data and will in turn allow for a proper evaluation of flight effects on the exhaust noise results. The model scale data are also compared with the coaxial jet noise prediction. Above 1000 Hz, the prediction is nominally 0 to 3 dB higher than the data. The arithmetic mean of the differences between the experimental OASPL and the predicted OASPL for all angles for each run ranged from 0 to -3.2 dB. The standard deviation of all the OASPL differences is 2.2 dB. The discrepancies are greatest at low primary jet velocities and appear to be due to inadequacy in the variable jet density exponent incorporated in the prediction procedure.

Groesbeck, D. E.↗

NASA NTRS1982

Fractionation of mineral species by electrophoresis

The fractionation of fine-grained aggregates into their major components is a problem in many scientific areas including earth and planetary science. Electrophoresis, the transport of electrically charged particles, immersed in a suspension medium, by a direct current field (Bier, 1959), was employed in this study as a means of separating simulated lunar soil into its constituent minerals. In these tests, conducted in a static analytical cylindrical microelectrophoresis apparatus, samples of simulated lunar soil and samples of pure mineral constituents were placed in the chamber; the electrophoretic mobilities of the lunar soil and the individual mineral constituents were measured. In most of the suspension buffers employed separability was indicated, on the basis of differences in mobility, for all the constituent mineral species except ilmenite and pyroxene, which were not efficiently separable in any of the buffers. Although only a few suspension media were employed, the success of this initial study suggests that electrophoresis may be an important mineral fractionation option in fine-grained aggregate processing.

Dunning, J. D.↗

NASA NTRS1984

Quantitative assessment of damage growth in graphite epoxy laminates by acousto-ultrasonic measurements

The acoustoultrasonic NDT method proposed by Vary (1976, 1978) for composite laminate damage growth quantitative assessment can both respond to the development of damage states and furnish quantitative parameters that monitor this damage development. Attention is presently given to data obtained for the case of quasi-static loading and fatigue testing of graphite-epoxy laminates. The shape parameters of the power spectral density for the ultrasonic signals correlate well with such other indications of damage development as stiffness degradation.

Talreja, R.↗