SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The fluid mechanics and heat transfer of motions driven by surface tension gradients (Marangoni convection) were analyzed theoretically to obtain an understanding of the convection accompanying the process of growing high quality single crystals from the melt in a mu-g environment. The geometries considered include two dimensional liquid filled slots and axisymmetric float zone configurations.
The leakage test program was one of such supporting technology programs structured to provide guidance to the Energy Efficient Engine High Pressure Turbine Component Design Effort. Leakage reduction techniques were identified and evaluated. Test models were used to simulate component leak paths and to evaluate leakage reduction techniques. These models simulated the blade/disk attachment, the vane inner platform attachment, and the vane outer platform attachment combined with the blade outer airseal. Disk blade attachment testing indicated that leakage in this area could be reduced to very low levels by paying careful attention to the tolerances along the contact surface between the blade vibration damper and the blade platform contact surface. The aim of feather seal testing was to achieve a goal for an effective leakage gap of one mil (.001 inch) per inch of feather seal length. Results indicated that effective gaps even below the goal level were achievable by (1) maintaining close tolerances between feather seals and their slots to minimize end gaps and limit seal rotation, (2) avoiding feather seal overlap, and (3) minimizing feather seal intersections. W seals were shown to be effective leakage control devices. Wire rope, in its present state of development, was shown not to be an effective sealing concept for application to the component design.
Low supersonic wave drag makes the thin highly swept delta wing the logical choice for use on aircraft designed for supersonic cruise. However, the high-lift maneuver capability of the aircraft is limited by severe induced-drag penalties attributed to loss of potential flow leading-edge suction. This drag increase may be alleviated through leading-edge flow control to recover lost aerodynamic thrust through either retention of attached leading-edge flow to higher angles of attack or exploitation of the increased suction potential of separation-induced vortex flow. A low-speed wind-tunnel investigation was undertaken to examine the high-lift devices such as fences, chordwise slots, pylon vortex generators, leading-edge vortex flaps, and sharp leading-edge extensions. The devices were tested individually and in combinations in an attempt to improve high-alpha drag performance with a minimum of low-alpha drag penalty. This report presents an analysis of the force, moment, and static pressure data obtained in angles of attack up to 23 deg, at Mach and Reynolds numbers of 0.16 and 3.85 x 10 to the 6th power per meter, respectively. The results indicate that all the devices produced drag and longitudinal/lateral stability improvements at high lift with, in most cases, minor drag penalties at low angles of attack.
The single entry interference problem is treated for frequency sharing between the broadcasting satellite and intersatellite services near 23 GHz. It is recommended that very long (more than 120 longitude difference) intersatellite hops be relegated to the unshared portion of the band. When this is done, it is found that suitable orbit assignments can be determined easily with the aid of a set of universal curves. An attempt to develop synthesis procedures for optimally assigning frequencies and orbital slots for the broadcasting satellite service in region 2 was initiated. Several discrete programming and continuous optimization techniques are discussed.
A Land Mobile Satellite System (LMSS) provides voice, data and related communications services to moving vehicles and persons. Communications between the mobiles and satellite are in the 806-890 MHz band. The satellite translates these signals to a ""fixed services band'' such as 14/12 GHz band (Ku-band), and communicates in this band with fixed terminals called gateways. The gateways are located at convenient places such as telephone switches (which provide entry into the national telephone system), dispatcher headquarters, computer centers, etc. Communications are therefore principally mobile to fixed. A third communications link, also at Ku-band, is needed between the satellite and a single fixed ground station. This link provides satellite command, telemetry and ranging and also provides a network control function. The latter, through a common signalling system, receives requests and assigns channel slots, and otherwise controls, monitors and polices the network and collects billing information.
A non-invasive method and apparatus is disclosed for measuring pressure within a pliable vessel such as a blood vessel. The blood vessel is clamped by means of a clamping structure having a first portion housing a pressure sensor and a second portion extending over the remote side of the blood vessel for pressing the blood vessel into engagement with the pressure sensing device. The pressure sensing device includes a flat deflectable diaphragm portion arranged to engage a portion of the blood vessel flattened against the diaphragm by means of the clamp structure. In one embodiment, the clamp structure includes first and second semicylindrical members held together by retaining rings. In a second embodiment the clamp structure is of one piece construction having a solid semicylindrical portion and a hollow semicylindrical portion with a longitudinal slot in the follow semicylindrical portion through which a slip the blood vessel. In a third embodiment, an elastic strap is employed for clamping the blood vessel against the pressure sensing device.
A wound-field axial-flux dc motor was developed for an electric vehicle drive system. The motor is essentially an axial-flux version of the classical Gramme-ring winding motor, but the active conductors are recessed into slots cut into the two opposite faces of the laminated tape-wound core ring. Three motors were built and tested in the program. The second (functional) model was a six-pole machine which weighed 88.5 kg. It developed 16.9 km (33.0 hp), and a max speed of 4800 rpm. Full load efficiency was 92% and predicted SAE D-cycle efficiency was 88%. The last engineering) model was a 4-pole machine with compoles, allowing a weight reduction to 45 kg (100 lbs.) while addressing some manufacturability problems. The engineering model was rated at 13.2 kw (17.6 hp) at 3000 rpm, with a peak power of 19.8 km (26.4 hp) and a max speed of 7200 rpm. Initial test results on this motor showed poor commutation and efficiency; the program was terminated without resolution of these problems.
Three dimensional adaptive-wall experiments were performed in the Ames Research Center (ARC) 25- by 13-cm indraft wind tunnel. A semispan wing model was mounted to one sidewall of a test section with solid sidewalls, and slotted top and bottom walls. The test section had separate top and bottom plenums which were divided into streamwise and cross-stream compartments. An iterative procedure was demonstrated for measuring wall interference and for adjusting the plenum compartment pressures to eliminate such interference. The experiments were conducted at a freestream Mach number of 0.60 and model angles of attack between 0 and 6 deg. Although in all the experiments wall interference was reduced after the plenum pressures were adjusted, interference could not be completely eliminated.
A method which is used to measure time delay accurately by using a Type 900-LB slotted line is described. The accuracy for calibrating time delay of a precision coaxial air line Type 900-L is about + or - (0.4 to 0.6)ps, and for coaxial cables with VSWR less than 1.5 and time delay t less than 50ns is about + or - (3 to 5)ps. Theoretical analysis and mathematical derivation of microwave networks in cascade are given. Methods to eliminate the errors which are caused by the discontinuities and the error analysis of the measuring system are presented. Skin effect analysis of the transient characteristic of coaxial transmission line are discussed in detail. Methods to eliminate the errors which result from using the calibrated time delay standard to calibrate time interval measurement instruments are presented. The estimation of errors and formulae for correction of those errors are described.
A one-dimensional distributed-parameter dynamic model of a cryogenic wind tunnel was developed which accounts for internal and external heat transfer, viscous momentum losses, and slotted-test-section dynamics. Boundary conditions imposed by liquid-nitrogen injection, gas venting, and the tunnel fan were included. A time-dependent numerical solution to the resultant set of partial differential equations was obtained on a CDC CYBER 203 vector-processing digital computer at a usable computational rate. Preliminary computational studies were performed by using parameters of the Langley 0.3-Meter Transonic Cryogenic Tunnel. Studies were performed by using parameters from the National Transonic Facility (NTF). The NTF wind-tunnel model was used in the design of control loops for Mach number, total temperature, and total pressure and for determining interactions between the control loops. It was employed in the application of optimal linear-regulator theory and eigenvalue-placement techniques to develop Mach number control laws.
Four dimensional modulation as a means of improving communication efficiency on the band-limited Gaussian channel, with the four dimensions of signal space constituted by phase orthogonal carriers (cos omega sub c t and sin omega sub c t) simultaneously on space orthogonal electromagnetic waves are discussed. "Frequency reuse' techniques use such polarization orthogonality to reuse the same frequency slot, but the modulation is not treated as four dimensional, rather a product of two-d modulations, e.g., QPSK. It is well known that, higher dimensionality signalling affords possible improvements in the power bandwidth sense. Four-D modulations based upon subsets of lattice-packings in four-D, which afford simplification of encoding and decoding are described. Sets of up to 1024 signals are constructed in four-D, providing a (Nyquist) spectral efficiency of up to 10 bps/Hz. Energy gains over the reuse technique are in the one to three dB range t equal bandwidth.
Free stream fluctuating pressures are determined from hot-wire measurements in a Mach 3.5 pilot quiet nozzle over a unit Reynolds number range from 10-60 million per meter. Further, the transition Reynolds numbers on a sharp tip 5 degree half-angle cone at zero angle of attack are obtained over the same range of unit Reynolds numbers from equilibrium temperature measurements on the cone. Results show that the nozzle provides noise levels in the upstream regions of the test rhombus that are substantially lower than in conventional nozzles. The normalized rms levels of the fluctuating static pressures are found to vary from extremely low values of less than 0.03% up to about 0.8% depending on the unit Reynolds number, the axial location in the test rhombus, and the bleed slot flow. By opening the boundary-layer bleed flow, the wall boundary layers over upstream regions of the nozzle become laminar and the absence of high frequency radiated noise then results in cone transition Reynolds numbers that are in the range of free-flight data. As the unit Reynolds numbers are increased, the nozzle wall boundary layers become transitional and turbulent, and the noise increases to peak levels of about 0.5% with significant energy up to 150 KHz. The cone transition Reynolds numbers then decrease to values that are in the range of those measured in conventional wind tunnels.
A linear method is developed which accounts for the effects of boundary layers on solid walls in subsonic three-dimensional wind tunnels. The streamwise gradient of the displacement thickness for a solid-wall boundary layer is expressed in terms of the von Karman momentum integral. The growth of the boundary layer due to the wall shearing stress is small compared to the variation caused by the model-induced pressure gradient. The viscous boundary condition can be expressed in terms of the edge velocity gradient and the gradient of the inviscid velocity potential function at the wall. Utilizing this analysis on the solid walls of several three-dimensional wind tunnel configurations shows that the most pronounced wall boundary-layer effect is on solid blockage for completely closed wind tunnels. For solid-wall tunnel configurations, the streamline curvature interference factor is reduced by a significant amount, while the lift interference factor at the model station does not depend on the boundary-layer parameter. For combination wall configurations, the slot effect of the horizontal walls dominates the viscous effect of the solid sidewalls.
The fabrication of different types of honeycomb mirrors with various kinds of borosilicate glass is discussed. Borosilicate glass is much less expensive to make than zero expansion glass, and can be used for ground-based applications. A mirror 60 cm in diameter made with a slotted strut or egg-crate honeycomb of 6 mm polished Pyrex plate is shown. The faceplates are 12 mm thick, laminated from the same 6 mm sheet. The result of an interferometric test is shown, with residual errors of about wavelength/8 RMS. An alternative fabrication technique for very large mirrors which require high quality bonds between separate sheets of thick Pyrex is described. The result of a recent test casting of a 60 cm honeycomb structure made in a mold with towers 14 cm square and 6 mm gaps between is shown, and methods to cast an entire mirror in one operation are discussed.
Characterizations of the Saturn magnetospheric activities that have been made possible through data gathered by means of the Pioneer 11 and Voyagers 1 and 2 flybys are reviewed. The spacecraft data confirmed the presence of a Saturn magnetosphere, which features inward diffusion and energization of trapped energetic particles as well as cosmic ray albedo neutron decay as a source of inner belt protons. A dense plasma was identified in the region covering the outer magnetosphere to the magnetopause, which extends outward 17.3-23.6 Saturn radii on the sunward side and from 30.3-70 radii on the far side, according to the satellite measurements. Characteristics of the particle populations and behaviors of the outer magnetosphere, the slot region, the inner magnetosphere, and the ring region are reviewed, as are those of the magnetic field, the solar wind-magnetospheric interaction, and the Titan-magnetospheric interaction are described. Further investigation of the longitudinal asymmetry of decimetric radio emissions from Saturn is recommended.
Two efforts to numerically simulate the flow about the Augmentor-Wing airfoil in the cruise configuration using the GRAPE elliptic partial differential equation grid generator algorithm are discussed. The Augmentor-Wing consists of a main airfoil with a slotted trailing edge for blowing and two smaller airfoils shrouding the blowing jet. The airfoil and the algorithm are described, and the application of GRAPE to an unsteady viscous flow simulation and a transonic full-potential approach is considered. The procedure involves dividing a complicated flow region into an arbitrary number of zones and ensuring continuity of grid lines, their slopes, and their point distributions across the zonal boundaries. The method for distributing the body-surface grid points is discussed.
This paper presents the design of a packet-switched communication system using a multi-beam, beam switched satellite repeater. The protocol provides a combination of random access via Slotted ALOHA techniques and demand assigned access using collision requests. This allows efficient bandwidth usage and low average delays. Minimization of earth station cost was a major objective. This was achieved by transferring the bulk of the system complexity to the satellite repeater and the (ground) network controller. This centrally controlled protocol would allow greater system stability and would permit system reconfiguration in response to changes in traffic intensity. Sufficient signalling is also incorporated to allow both rate diversity to combat fading and timing corrections to account for satellite drift.
Thermocapillarity can drive steady flows in float-zone configurations. These flows can become unstable and exhibit time-periodic oscillations. In order to obtain insight into such phenomena, studies are made of a simplified system consisting of liquid in a two-dimensional slot. Steady flows and their instabilities are examined.