Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phase transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

A resistive-gate Al(0.3)Ga(0.7)As/GaAs 2DEG CCD with high charge-transfer efficiency at 1 GHz

The fabrication and performance of an Al(0.3)Ga(0.7)As/GaAs modulation-doped resistive-gate CCD are reported. The two-dimensional electron gas (2DEG) CCD, implemented as a 32-stage four-phase delay line, was tested at both low (1-13 MHz) and high (0.6-1.0 GHz) frequency. It exhibits a room-temperature charge-transfer efficiency (CTE) of better than 0.999 at clock frequencies from 10 MHz up to 1 GHz without a fat-zero signal and is limited by dark current below 10 MHz. The high-frequency test showed no CTE degradation up to 1-GHz operation. The CTE degraded at frequencies lower than approximately 5 MHz due to dark current. The charge-handling capability and minimum clock swing of the resistive-gate 2DEG CCD are calculated.

Song, J.-I.↗
NASA NTRS1988

Large inclination change using lunar-swingby techniques

The use of lunar-swingby maneuvers to transfer a spacecraft from an equatorial orbit to a polar orbit has been investigated in order to verify the technical feasibility of the NASA/ESA equatorial science phase (ESP)/Cluster mission. The solar aspect angle constraints of the spacecraft spin-axis and the dependence of the total Delta-V cost of the transfer on the initial ESP orbital parameters (particularly perigee radius and inclination) have been studied. The results indicate that a satisfactory ESP-to-Cluster orbit transfer can be achieved using a double lunar-swingby sequence.

Lee, T.↗
DOE OSTI2026

Imaging surface topography with coherent x-ray reflectivity: Theory, kinematics, and simulations

A theoretical formalism is described for understanding coherent x-ray reflectivity (CXR) from the surface of a semi-infinite crystal having a variable surface topography, described by the height profile ℎ(𝑥,𝑦). The surface topography is imaged as a complex “effective density,” obtained from the phasing and inversion of the coherent x-ray reflectivity data, measured through a rocking scan centered at a vertical momentum transfer 𝑄$^{0}_{𝑧}$ and a vertical range Δ⁢𝑄 𝑧 . The formalism predicts that the effective density has an amplitude with a maximum located at the surface height for each position within the surface plane. The phase of the effective density has a lateral variation that is controlled by the surface height and a vertical variation that reflects a combination of the interfacial structure and specific choice of measurement conditions. This understanding enables direct observation of nanometer-scale interfacial topography, i.e., ℎ⁡(𝑥,𝑦)⁢𝑐 𝑠 (where 𝑐 𝑠 is the vertical substrate lattice parameter) with Å-scale sensitivity to surface height. Numerical simulations illustrate and confirm the theoretical results. These results show how the interpretation of the interfacial density phase obtained by CXR data inversion (i.e., surface topography with respect to a flat surface) is conceptually similar to that previously known for Bragg coherent diffraction imaging (BCDI) measurements of isolated nanoparticles (i.e., lattice displacements with respect to an ideal crystal lattice). This suggests that CXR can be thought of as a form of dark field imaging with respect to the bright field BCDI approach. An implication of these results is that interfacial imaging may bypass some of the significant challenges associated with BCDI imaging of multiple particles having different orientations.

X-ray imaging↗
NASA NTRS1985

Turbine blade and vane heat flux sensor development, phase 2

The development of heat flux sensors for gas turbine blades and vanes and the demonstration of heat transfer measurement methods are reported. The performance of the heat flux sensors was evaluated in a cylinder in cross flow experiment and compared with two other heat flux measurement methods, the slug calorimeter and a dynamic method based on fluctuating gas and surface temperature. Two cylinders, each instrumented with an embedded thermocouple sensor, a Gardon gauge, and a slug calorimeter, were fabricated. Each sensor type was calibrated using a quartz lamp bank facility. The instrumented cylinders were then tested in an atmospheric pressure combustor rig at conditions up to gas stream temperatures of 1700K and velocities to Mach 0.74. The test data are compared to other measurements and analytical prediction.

Atkinson, W. H.↗
DOE OSTI2024

Electrical Control of Magnetic Resonance in Phase Change Materials

Metal–insulator transitions (MITs) in resistive switching materials can be triggered by an electric stimulus that produces significant changes in the electrical response. When these phases have distinct magnetic characteristics, dramatic changes in the spin excitations are also expected. The transition metal oxide La 0.7 Sr 0.3 MnO 3 (LSMO) is a ferromagnetic metal at low temperatures and a paramagnetic insulator above room temperature. When LSMO is in its metallic phase, a critical electrical bias has been shown to lead to an MIT that results in the formation of a paramagnetic resistive barrier transverse to the applied electric field. Using spin-transfer ferromagnetic resonance spectroscopy, we show that even for electrical biases less than the critical value that triggers the MIT, there is magnetic phase separation, with the spin-excitation resonances varying systematically with applied bias. Therefore, voltage-triggered MITs in LSMO can alter magnetic resonance characteristics, offering an effective method for tuning synaptic weights in neuromorphic circuits.

36 MATERIALS SCIENCE↗
NASA NTRS1994

Two-way satellite time transfer: Overview and recent developments

The experiment using small earth stations for transatlantic two-way satellite time transfer between the USA and Germany has had its 10th anniversary this year. Pseudo-random noise coded time signals were phase modulated and demodulated at each station using a modem. Recently, during the last two weeks of Aug. 1993, six European time laboratories have used the INTELSAT 307E satellite for line-up tests and preliminary time transfer sessions using the same type of MITREX modem. The need for a uniform format for the exchange of data was felt heavily after these sessions. This problem was foreseen and addressed in international working parties. During Apr. 1993, in Task Group 7/2 of the ITU Radiocommunication Sector, a very intense discussion has taken place about what procedure should be recommended for TWSTFT and what items the header and data lines of the resulting data fields should contain. A difficulty is that two different methods of calibration of the earth station delays exist which result in different sets of delay data to be exchanged. Further study and discussions are necessary. Also, a meeting of the CCDS Working Group on TWSTFT addressed this in Oct. 1993. The outcome of the discussions and the prospect for future developments are presented.

Dejong, Gerrit↗
DOE OSTI2020

Spectroscopic Studies of Charge-Transfer Character and Photoresponses of F 4 TCNQ-Based Donor–Acceptor Complexes

F 4 TCNQ (2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane) is used widely as a hole-doping agent in photoresponsive organic semiconducting materials, yet relatively little is known about the photoresponses of the F 4 TCNQ· - anion generated via doping. Furthermore, there is still relatively little systematic exploration of how the properties of the local material or chemical environment impacts the driving force for generating these charge-transfer complexes. Here we present spectroscopic and photophysical studies of F 4 TCNQ in charge-transfer complexes (CTCs) with the electron donor N,N’-Diphenyl-N-N’-di-p-tolylbenzene-1,4-diamine (MPDA) both in dichloroethane solution and polystyrene matrices. Integer charge transfer (ICT) between donor and acceptor occurs readily in dichloroethane solvent to form F 4 TCNQ· - :MPDA + CTCs, due to a ~150 mV difference in MPDA + /MPDA and F 4 TCNQ/F 4 TCNQ· - reduction potentials. Ultrafast spectroscopic studies of the CTC as well as electrochemically generated F 4 TCNQ· - and MDPA + reveal that the photoresponses of these CTCs are dominated by that of the dopant anion, including rapid deactivation (800 fs) after excitation to the anion D 1 excited state, followed by slower (~10 ps) vibrational cooling in the anion D 0 state. Excitation to the higher-lying D 2 state results in a rapid relaxation to the D 1 state, in contrast to direct D 2 -D 0 relaxation previously observed for F 4 TCNQ· - in gas phase. CTCs embedded in polystyrene (PS) matrices are observed to lose their integer charge-transfer character upon evaporation of solvent, as evidenced by changes to electronic and vibrational absorption features associated with F 4 TCNQ· - . This change is attributed to the loss of solvent stabilization of the ion pair formed through the charge-transfer reaction. Ultrafast spectral measurements reveal that the photoresponses of the partial charge-transfer (PCT) species embedded in PS are still highly similar to those of the ICT species and unlike that of neutral F 4 TCNQ, implying the electronic properties of the PCT state are likewise dominated by properties of the reduced acceptor molecule. We conclude that excitation of ICT or PCT states introduces optical losses for photoresponses of doped organic semiconductor materials due to the large anion absorption cross section and its rapid, dissipative deactivation dynamics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Phase-space entropy cascade and irreversibility of stochastic heating in nearly collisionless plasma turbulence

We consider a nearly collisionless plasma consisting of a species of “test particles” in one spatial and one velocity dimension, stirred by an externally imposed stochastic electric field—a kinetic analog of the Kraichnan model of passive advection. The mean effect on the particle distribution function is turbulent diffusion in velocity space—known as stochastic heating. Accompanying this heating is the generation of fine-scale structure in the distribution function, which we characterize with the collisionless (Casimir) invariant C 2 ∝ ∫ ∫ d x d v 〈 f 2 〉 —a quantity that here plays the role of (negative) entropy of the distribution function. We find that C 2 is transferred from large scales to small scales in both position and velocity space via a phase-space cascade enabled by both particle streaming and nonlinear interactions between particles and the stochastic electric field. We compute the steady-state fluxes and spectrum of C 2 in Fourier space, with k and s denoting spatial and velocity wave numbers, respectively. In our model, the nonlinearity in the evolution equation for the spectrum turns into a fractional Laplacian operator in k space, leading to anomalous diffusion. Whereas even the linear phase mixing alone would lead to a constant flux of C 2 to high s (towards the collisional dissipation range) at every k , the nonlinearity accelerates this cascade by intertwining velocity and position space so that the flux of C 2 is to both high k and high s simultaneously. Integrating over velocity (spatial) wave numbers, the k -space ( s -space) flux of C 2 is constant down to a dissipation length (velocity) scale that tends to zero as the collision frequency does, even though the rate of collisional dissipation remains finite. The resulting spectrum in the inertial range is a self-similar function in the ( k , s ) plane, with power-law asymptotics at large k and s . Our model is fully analytically solvable, but the asymptotic scalings of the spectrum can also be found via a simple phenomenological theory whose key assumption is that the cascade is governed by a “critical balance” in phase space between the linear and nonlinear timescales. We argue that stochastic heating is made irreversible by this entropy cascade and that, while collisional dissipation accessed via phase mixing occurs only at small spatial scales rather than at every scale as it would in a linear system, the cascade makes phase mixing even more effective overall in the nonlinear regime than in the linear one. Published by the American Physical Society 2024

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1991

The Air Force Manufacturing Technology (MANTECH): Technology transfer methodology as exemplified by the radar transmit/receive module program

The Air Force Manufacturing Technology program is involved with the improvement of radar transmit/receive modules for use in active phased array radars for advanced fighter aircraft. Improvements in all areas of manufacture and test of these modules resulting in order of magnitude improvements in the cost of and the rate of production are addressed, as well as the ongoing transfer of this technology to the Navy.

Houpt, Tracy↗
NASA NTRS2013

The Supercritical Pile Gamma-Ray Burst Model: The GRB Afterglow Steep Decline and Plateau Phase

We present a process that accounts for the steep decline and plateau phase of the Swift X-Ray Telescope (XRT) light curves, vexing features of gamma-ray burst (GRB) phenomenology. This process is an integral part of the "supercritical pile" GRB model, proposed a few years ago to account for the conversion of the GRB kinetic energy into radiation with a spectral peak at E(sub pk) is approx. m(sub e)C(exp 2). We compute the evolution of the relativistic blast wave (RBW) Lorentz factor Gamma to show that the radiation-reaction force due to the GRB emission can produce an abrupt, small (approx. 25%) decrease in Gamma at a radius that is smaller (depending on conditions) than the deceleration radius R(sub D). Because of this reduction, the kinematic criticality criterion of the "supercritical pile" is no longer fulfilled. Transfer of the proton energy into electrons ceases and the GRB enters abruptly the afterglow phase at a luminosity smaller by approx. m(sub p)/m(sub e) than that of the prompt emission. If the radius at which this slow-down occurs is significantly smaller than R(sub D), the RBW internal energy continues to drive the RBW expansion at a constant (new) Gamma and its X-ray luminosity remains constant until R(sub D) is reached, at which point it resumes its more conventional decay, thereby completing the "unexpected" XRT light curve phase. If this transition occurs at R is approx. equal to R(sub D), the steep decline is followed by a flux decrease instead of a "plateau," consistent with the conventional afterglow declines. Besides providing an account of these peculiarities, the model suggests that the afterglow phase may in fact begin before the RBW reaches R is approx. equal to R(sub D), thus providing novel insights into GRB phenomenology.

parameters↗
NASA NTRS2003

Human Exploration of Earth's Neighborhood and Mars

The presentation examines Mars landing scenarios, Earth to Moon transfers comparing direct vs. via libration points. Lunar transfer/orbit diagrams, comparison of opposition class and conjunction class missions, and artificial gravity for human exploration missions. Slides related to Mars landing scenarios include: mission scenario; direct entry landing locations; 2005 opportunity - Type 1; Earth-mars superior conjunction; Lander latitude accessibility; Low thrust - Earth return phase; SEP Earth return sequence; Missions - 200, 2007, 2009; and Mission map. Slides related to Earth to Moon transfers (direct vs. via libration points (L1, L2) include libration point missions, expeditionary vs. evolutionary, Earth-Moon L1 - gateway for lunar surface operations, and Lunar mission libration point vs. lunar orbit rendezvous (LOR). Slides related to lunar transfer/orbit diagrams include: trans-lunar trajectory from ISS parking orbit, trans-Earth trajectories, parking orbit considerations, and landing latitude restrictions. Slides related to comparison of opposition class (short-stay) and conjunction class (long-stay) missions for human exploration of Mars include: Mars mission planning, Earth-Mars orbital characteristics, delta-V variations, and Mars mission duration comparison. Slides related to artificial gravity for human exploration missions include: current configuration, NEP thruster location trades, minor axis rotation, and example load paths.

Condon, Gerald↗
DOE OSTI2023

Epitaxial growth of highly symmetrical branched noble metal-semiconductor heterostructures with efficient plasmon-induced hot-electron transfer

Epitaxial growth is one of the most commonly used strategies to precisely tailor heterostructures with well-defined compositions, morphologies, crystal phases, and interfaces for various applications. However, as epitaxial growth requires a small interfacial lattice mismatch between the components, it remains a challenge for the epitaxial synthesis of heterostructures constructed by materials with large lattice mismatch and/or different chemical bonding, especially the noble metal-semiconductor heterostructures. Here, we develop a noble metal-seeded epitaxial growth strategy to prepare highly symmetrical noble metal-semiconductor branched heterostructures with desired spatial configurations, i.e., twenty CdS (or CdSe) nanorods epitaxially grown on twenty exposed (111) facets of Ag icosahedral nanocrystal, albeit a large lattice mismatch (more than 40%). Importantly, a high quantum yield (QY) of plasmon-induced hot-electron transferred from Ag to CdS was observed in epitaxial Ag-CdS icosapods (18.1%). This work demonstrates that epitaxial growth can be achieved in heterostructures composed of materials with large lattice mismatches. The constructed epitaxial noble metal-semiconductor interfaces could be an ideal platform for investigating the role of interfaces in various physicochemical processes.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Probing Supercritical Phase Transition using Ultrafast X-ray Diagnostics (Final Technical Report)

Over recent years, several hypotheses have been put forward to elucidate supercritical transition states. Despite significant progress on the fundamental understanding of fluids at these supercritical conditions, important questions concerning the microstructure and dynamical processes remain. A particular research issue is hereby the fundamental understanding of the morphology of the molecular microstructure and its effect on the macroscopic behaviour and thermodynamic response functions. It is widely believed that the supercritical state is homogeneous without structural and dynamic observables to distinguish between a liquid and a vapor. However, recent investigations have identified regions of distinct liquid-like or vapor-like properties even under supercritical conditions. Specifically, it was shown that the transition between liquid-like and vapor-like states occurs across an extension to the coexistence line, marked by almost discontinuous changes in fluid properties. This transition was first identified experimentally by Nishikawa and Tanaka and stands in contrast to the classical presentation of the supercritical state space as a featureless, homogeneous domain. Structurally, the most important properties of supercritical fluids are the dynamic heterogeneities and local density fluctuations that are present within the fluid state at the microscopic level. These inhomogeneities are associated with the formation of molecular clusters of various sizes with liquid-like properties separated by voids of unbound gas-phase molecules which continuously restructure itself at picosecond timescales. By utilizing ultrafast X-ray Photon Correlation Spectroscopy (XPCS) at the Linac Coherent Light Source (LCLS) and X-ray synchrotron measurements as an experimental probe of these structural changes at the molecular level we seek to elucidate the higher-order phase transition from a liquid-like to a vapor-like state in the region extending the critical point. Open questions we seek to address particularly with XPCS are: (i) the underlying mechanisms responsible for the density fluctuations at supercritical conditions and how these dynamical processes at the molecular level affect the thermodynamic response functions and (ii) on what timescales do dynamical processes evolve that are associated with thermalization, molecular diffusion, and intermolecular cluster transfer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

CFD Simulation of Biomass Pyrolysis Vapor Upgrading over a Pt/TiO 2 Catalyst in Fixed and Moving Beds

This report presents a comprehensive computational fluid dynamics (CFD) study of the biomass pyrolysis vapor phase upgrading and the catalyst regeneration in different reactors under various operational conditions. This study used the open-source software Multiphase Flow with Interphase eXchanges (MFiX), developed at National Energy Technology Laboratory (NETL) for simulating hydrodynamics, heat transfer, and chemical reactions in multiphase systems. This simulation solved the conservation of mass, momentum, energy, species for gas and solid phases with chemical reactions.

09 BIOMASS FUELS↗
DOE OSTI2021

Summary of DASSH-CFD Inter-Assembly Heat Transfer Comparison

Fast reactor core design requires integration of detailed power distributions obtained from neutronics models and thermal fluids calculations to determine temperature distributions and flow conditions. During the design phase, calculations may be repeated as specifications change and computational expense must be balanced with solution accuracy, creating an opportunity for the use of intermediate-fidelity codes. To that end, the Ducted Assembly Steady-State Heat Transfer Software (DASSH) has been developed at Argonne National Laboratory to perform full-core, steady state coolant and fuel pin temperature calculations in reactors consisting of hexagonal, ducted assemblies. DASSH is a first-order, finite volume subchannel code based on methodologies initially introduced in the legacy thermal hydraulics codes SUPERENERGY-2 and SE2-ANL. It can work coupled with the Argonne Reactor Computational (ARC) code suite to obtain neutron and gamma power distributions based on neutron transport solutions and features many improvements and new capabilities compared to its predecessors. DASSH calculates temperatures by balancing energy between subchannels and relies on correlations to account for flow distribution and coolant mixing.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Microhydration of the metastable N -Protomer of 4-Aminobenzoic acid by condensation at 80 K: H/D exchange without conversion to the more stable O- protomer

4-Aminobenzoic acid (4ABA) is a model scaffold for studying solvent-mediated proton transfer. Although protonation at the carboxylic group (O-protomer) is energetically favored in the gas phase, the N-protomer, where the proton remains on the amino group, can be kinetically trapped by electrospray ionization of 4ABA in an aprotic solvent such as acetonitrile. Here we report the formation of the hydrated deuterium isotopologues of the N-protomers, RND 3 + ·(H 2 O) n=1-3 , (R=C 6 H 4 COOD), which are generated by condensing water molecules onto the bare N-protomers in a liquid nitrogen cooled, radiofrequency octopole ion trap at 80 K. The product clusters are then transferred to a 20 K cryogenic ion trap where they are tagged with weakly bound D 2 molecules. The structures of these clusters are determined by analysis of their vibrational patterns obtained by resonant IR photodissociation. The resulting patterns confirm that the metastable N-protomer configuration remains intact even when warmed by sequential condensation of water molecules. Attachment of H 2 O molecules onto the RND 3 + head group also affords the opportunity to explore the possibility of H/D exchange between the acid scaffold and the proximal water network. The spectroscopic results establish that although the RND 3 + ·(H 2 O) n=1,2 clusters are formed without H/D exchange, the n = 3 cluster exhibits about 10% H/D exchange as evidenced by the appearance of the telltale HOD bands. Furthermore, the site of exchange on the acid is determined to be the acidic OH by the emergence of the OH stretching fundamental in the -COOH motif.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1989

Software reuse issues affecting AdaNET

The AdaNet program is reviewing its long-term goals and strategies. A significant concern is whether current AdaNet plans adequately address the major strategic issues of software reuse technology. The major reuse issues of providing AdaNet services that should be addressed as part of future AdaNet development are identified and reviewed. Before significant development proceeds, a plan should be developed to resolve the aforementioned issues. This plan should also specify a detailed approach to develop AdaNet. A three phased strategy is recommended. The first phase would consist of requirements analysis and produce an AdaNet system requirements specification. It would consider the requirements of AdaNet in terms of mission needs, commercial realities, and administrative policies affecting development, and the experience of AdaNet and other projects promoting the transfer software engineering technology. Specifically, requirements analysis would be performed to better understand the requirements for AdaNet functions. The second phase would provide a detailed design of the system. The AdaNet should be designed with emphasis on the use of existing technology readily available to the AdaNet program. A number of reuse products are available upon which AdaNet could be based. This would significantly reduce the risk and cost of providing an AdaNet system. Once a design was developed, implementation would proceed in the third phase.

Mcbride, John G.↗
DOE OSTI2022

Modeling mesoscale fission gas behavior in UO2 by directly coupling the phase field method to spatially resolved cluster dynamics

Abstract Fission gas release within uranium dioxide nuclear fuel occurs as gas atoms diffuse through grains and arrive at grain boundary (GB) bubbles; these GB bubbles grow and interconnect with grain edge bubbles; and grain edge tunnels grow and connect to free surfaces. In this study, a hybrid multi-scale/multi-physics simulation approach is presented to investigate these mechanisms of fission gas release at the mesoscale. In this approach, fission gas production, diffusion, clustering to form intragranular bubbles, and re-solution within grains are included using spatially resolved cluster dynamics in the Xolotl code. GB migration and intergranular bubble growth and coalescence are included using the phase field method in the MARMOT code. This hybrid model couples Xolotl to MARMOT using the MultiApp and Transfer systems in the MOOSE framework, with Xolotl passing the arrival rate of gas atoms at GBs and intergranular bubble surfaces to MARMOT and MARMOT passing evolved GBs and bubble surface positions to Xolotl. The coupled approach performs well on the two-dimensional simulations performed in this work, producing similar results to the standard phase field model when Xolotl does not include fission gas clustering or re-solution. The hybrid model performs well computationally, with a negligible cost of coupling Xolotl and MARMOT and good parallel scalability. The hybrid model predicts that intragranular fission gas clustering and bubble formation results in up to 70% of the fission gas being trapped within grains, causing the increase in the intergranular bubble fraction to slow by a factor of six. Re-solution has a small impact on the fission gas behavior at 1800 K but it has a much larger impact at 1000 K, resulting in a twenty-times increase in the concentration of single gas atoms within grains. Due to the low diffusion rate, this increase in mobile gas atoms only results in a small acceleration in the growth of the intergranular bubble fraction. Finally, the hybrid model accounts for migrating GBs sweeping up gas atoms. This results in faster intergranular bubble growth with smaller initial grain sizes, since the additional GB migration results in more immobile gas clusters reaching GBs.

Kim, Dong-Uk↗