Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “model testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

The phototron: A light to RF energy conversion device

The phototron, a photoelectric device that converts light to radio frequency energy, is described. It is a vacuum tube, free electron, device that is mechanically similar to a reflex klystron with the hot filament cathode replaced by a large area photocathode. The device can operate either with an external voltage source used to accelerate the photoelectrons or with zero bias voltage; in which case the photokinetic energy of the electrons sustains the R.F. oscillations in the tuned R.F. circuit. One basic design of the phototron was tested. Frequencies as high as about 1 GHz and an overall efficiency of about 1% in the biased mode were obtained. In the unbiased mode, the frequencies of operation and efficiences are considerably lower. Success with test model suggests that considerable improvements are possible through design refinements. One such design refinement is the reduction of the length of the electron flight path.

Freeman, J. W.↗
NASA NTRS1983

Aerodynamic characteristics of a series of single-inlet air-breathing missile configurations

A series of air-breathing missile configurations was investigated to provide a data base for the design of such missiles. The model could be configured with either a single axisymmetric or a two dimensional inlet located at the bottom of the body. Two tail configurations were investigated: a tri-tail and an X-tail. The tail surfaces could be deflected to provide pitch control. A wing could be located above the inlet on the center line of the model. Tests were made at supersonic Mach numbers with the inlet open and internal flow, and at subsonic-transonic Mach numbers with the internal duct closed and no internal flow.

Hayes, C.↗
NASA NTRS1983

Development of a simplified optical technique for the simultaneous measurement of particle size distribution and velocity

Existing techniques were surveyed, an experimental procedure was developed, a laboratory test model was fabricated, limited data were recovered for proof of principle, and the relationship between particle size distribution and amplitude measurements was illustrated in an effort to develop a low cost, simplified optical technique for measuring particle size distributions and velocities in fluidized bed combustors and gasifiers. A He-Ne laser illuminated Rochi Rulings (range 10 to 500 lines per inch). Various samples of known particle size distributions were passed through the fringe pattern produced by the rulings. A photomultiplier tube converted light from the fringe volume to an electrical signal which was recorded using an oscilloscope and camera. The signal amplitudes were correlated against the known particle size distributions. The correlation holds true for various samples.

Smith, J. L.↗
NASA NTRS1982

Space shuttle solid rocket booster water entry cavity collapse loads

Solid rocket booster cavity collapse flight measurements included external pressures on the motor case and aft skirt, internal motor case pressures, accelerometers located in the forward skirt, mid-body area, and aft skirt, as well as strain gages located on the skin of the motor case. This flight data yielded applied pressure longitudinal and circumferential distributions which compare well with model test predictions. The internal motor case ullage pressure, which is below atmospheric due to the rapid cooling of the hot internal gas, was more severe (lower) than anticipated due to the ullage gas being hotter than predicted. The structural dynamic response characteristics were as expected. Structural ring and wall damage are detailed and are considered to be attributable to the direct application of cavity collapse pressure combined with the structurally destabilizing, low internal motor case pressure.

Keefe, R. T.↗
NASA NTRS1981

A new electronic scanner of pressure designed for installation in wind-tunnel models

A new electronic scanner of pressure (ESOP) has been developed by NASA Ames Research Center for installation in wind-tunnel models. An ESOP system includes up to 20 pressure modules, each with 48 pressure transducers, an A/D converter, a microprocessor, a data controller, a monitor unit, and a heater controller. The system is sized so that the pressure modules and A/D converter module can be installed within an average-size model tested in the Ames Aerodynamics Division wind tunnels. This paper describes the ESOP system, emphasizing the main element of the system - the pressure module. The measured performance of the overall system is also presented.

Coe, C. T.↗
NASA NTRS1983

Progress toward the analysis of complex propulsion installation flow phenomenon

A trend toward replacement of parametric model testing with parametric analysis for the design of aircraft is driven by the rapidly escalating cost of wind tunnel testing, the increasing availability of large fast computers, and powerful numerical flow algorithms. In connection with the complex flow phenomena characteristic of propulsion installations, it is now necessary to employ both parametric analysis and testing for design procedures. Powerful flow analysis techniques are available to predict local flow phenomena. However, the employment of these techniques is very expensive. It is, therefore, necessary to link these analyses with less powerful and less expensive procedures for an accurate analysis of propulsion installation flowfields. However, the interfacing and coupling processes needed are not available. The present investigation is concerned with progress made regarding the development of suitable linking methods. Attention is given to methods of analysis for predicting the flow around a nacelle coupled to a highly swept wing.

Kern, P. R. A.↗
NASA NTRS1983

Advanced technology exhaust nozzle development

The requirement for greater tactical aircraft operational capabilities has led to increasing research emphasis on the refinement of engine/airframe integration methods and exhaust nozzle flexibility. A major prospective advancement in the development of these capabilities takes the form of multifunctional exhaust nozzle systems with thrust reversal and thrust vectoring features, whose operation will be shared by both airframe and powerplant control systems. Attention is presently given to the two-dimensional convergent-divergent and single expansion ramp nozzle designs, with emphasis on the variable geometry mechanical systems by which they assume cruising flight, vectoring, and thrust reversal operations. The nozzles have been wind tunnel model-tested for the cases of the F-18 fighter and a supersonic cruise configuration concept.

Dusa, D. J.↗
NASA NTRS1983

The Integrated Technology and Flight Research Rotor Technology demonstrators for the 1985-1995 timeframe

The purposes and progress in the Integrated Technology Rotor/Flight Research Rotor (ITR/FRR) Project, a joint effort by the U.S. Army and NASA, are outlined. The project goal is to integrate the disciplines of rotor design, aerodynamics, structures, materials, dynamics, and acoustics, to remove the risks in applying the technology, and to develop an advanced flight research rotor which permits significant variation in the rotor properties. Composite rotors are believed to be capable of displaying infinite fatigue lifetimes with fail-safe characteristics, and bearingless hubs simplify hub designs. The programs will also consider the flight control, propulsion, and structures. Concept definition contracts are presently distributed among five companies, and preliminary designs will lead to model tests in 1984.

Bousman, W.↗
NASA NTRS1984

A wind tunnel database using RIM

Engineering data base development which has become increasingly widespread to industry with the availability of data management systems is examined. A large data base was developed for wind tunnel data and related model test information, using RIM as the data base manager. The arrangement of the wind tunnel data into the proper schema for the most efficient database utilization is discussed. The FORTRAN interface program of RIM is used extensively in the loading phases of the data base and by the users. Several examples to illustrate how the Wind Tunnel Data base might be searched for specific data items and test information using RIM are presented.

Wray, W. O., Jr.↗
NASA NTRS1984

Aeropropulsive characteristics of nonaxisymmetric-nozzle thrust reversers at Mach numbers from 0 to 1.20

An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine the performance of nonaxisymmetric-nozzle thrust reversers installed on a generic twin-engine fighter aircraft model. Test data were obtained at static conditions and at Mach numbers from 0.15 to 1.20 with jet exhaust simulated by high pressure air. Results showed that reverse-thrust levels of greater than 50 percent at static conditions and greater than 30 percent at in-flight conditions could be achieved. Internal reverser-port passage length was found to be very important in improving reverser performance. Increasing the reverser-port passage length improved reverse-thrust performance by as much as 28 percent at static conditions and by as much as 17 percent at Mach 1.20.

Carson, G. T., Jr.↗
NASA NTRS1981

Measured transonic unsteady pressures on an energy efficient transport wing with oscillating control surfaces

Highlight results are presented from subsonic and transonic pressure measurement studies conducted in the Langley Transonic Dynamics Tunnel on a supercritical wing model representative of an energy efficient transport design. Steady- and unsteady-pressure data were acquired on the upper and lower wing surface at an off-design Mach number of 0.60 and at the design Mach number of 0.78, for a Reynolds number of 2.2 x 10(6) (based on the wing average chord). The model configuration consisted of a sidewall-Mounted half-body fuselage and a semi-span wing with an aspect ratio of 10.76, a leading-edge sweepback angle of 28.8 degrees, and supercritical airfoil sections. The wing is instrumented with 252 static pressure orifices and 164 dynamic pressure gages. Model test variables included wing angle of attack, control-surface mean deflection angle, control-surface oscillating deflection angle and frequency, and phasing between oscillating leading-edge and trailing-edge controls when used together.

Cazier, F. W., Jr.↗
NASA NTRS1984

Experimental study of performance degradation of a model helicopter main rotor with simulated ice shapes

An experimental study utilizing a remote controlled model helicopter has been conducted to measure the performance degradation due to simulated ice accretion on the leading edge of the main rotor for hover and forward flight. The 53.375 inch diameter main rotor incorporates a NACA 0012 airfoil with a generic ice shape corresponding to a specified natural ice condition. Thrust coefficients and torque coefficients about the main rotor were measured as a function of velocity, main rotor RPM, angle-of-incidence of the fuselage, collective pitch angle, and extent of spanwise ice accretion. An experimental airfoil data bank has been determined using a two-dimensional twenty-one inch NACA 0012 airfoil with scaled ice accretion shapes identical to that used on the model helicopter main rotor. The corresponding experimental data are discussed with emphasis on Reynolds number effects and ice accretion scale model testing.

Korkan, K. D.↗
NASA NTRS1984

An incompressible Navier-Stokes flow solver in three-dimensional curvilinear coordinate systems using primitive variables

An implicit, finite-difference computer code has been developed to solve the incompressible Navier-Stokes equations in a three-dimensional, curvilinear coordinate system. The pressure-field solution is based on the pseudo compressibility approach in which the time derivative pressure term is introduced into the mass conservation equation to form a set of hyperbolic equations. The solution procedure employs an implicit, approximate factorization scheme. The Reynolds stresses, that are uncoupled from the implicit scheme, are lagged by one time-step to facilitate implementing various levels of the turbulence model. Test problems for external and internal flows are computed, and the results are compared with existing experimental data. The application of this technique for general three-dimensional problems is then demonstrated.

Kwak, D.↗
NASA NTRS1982

Analysis of electromagnetic fields on an F-106B aircraft during lightning strikes

Information on the exterior electromagnetic environment of an aircraft when it is struck by lightning has been obtained during thunderstorm penetrations with an F-106B aircraft. Electric and magnetic fields were observed, using mainly time-derivative type sensors, with bandwidths to 50 MHz. Lightning pulse lengths ranging from 25 ns to 7 microsec have been recorded. Sufficient high-frequency content was present to excite electromagnetic resonances of the aircraft, and peaks in the frequency spectra of the waveforms in the range 7 to 23 MHz are in agreement with the resonant frequencies determined in laboratory scale-model tests. Both positively and negatively charged strikes were experienced, and most of the data suggest low values of peak current.

Trost, T. F.↗
NASA NTRS1984

Prediction of transonic separated flows

Johnson et al. (1982) have provided a detailed comparison between a thoroughly documented transonic flow with shock-induced separations and solutions of the flow using the Navier-Stokes equations. According to this comparison, there were several deficiencies in the computations. The present investigation takes into account new experimental data which have been obtained in a larger wind tunnel with the same test model for a wider range of freestream Mach numbers. The results of new Navier-Stokes computations using more compatible boundary conditions are shown, and the effects of the turbulence model choice on predicting Mach number trends are assessed.

Horstman, C. C.↗
NASA NTRS1984

A preliminary analysis of flight data from the AFTI/F-16 airplane

Flight test data from the AFTI/F-16 airplane are analyzed. Two flight control system modes (Independent Backup Unit and Standard Normal Mode) are considered. Estimated stability and control derivatives are compared with values from the wind tunnel and F-16A flight tests. Modeling difficulties are shown to arise due to the near-neutral static stability of the airplane and the number of coordinated control surface movements commanded in the Standard Normal Mode.

Batterson, J. G.↗
NASA NTRS1985

Continuous laminar smoke generator

A smoke generator capable of emitting a very thin, laminar stream of smoke for use in high detail flow visualization was invented. The generator is capable of emitting a larger but less stable rope of smoke. The invention consists of a pressure supply and fluid supply which supply smoke generating fluid to feed. The feed tube is directly heated by electrical resistance from current supplied by power supply and regulated by a constant temperature controller. A smoke exit hole is drilled in the wall of feed tube. Because feed tube is heated both before and past exit hole, no condensation of smoke generating occurs at the smoke exit hole, enabling the production of a very stable smoke filament. The generator is small in size which avoids wind turbulence in front of the test model.

Weinstein, L. M.↗
NASA NTRS1985

On the measurement of material damping in a simulated space environment

A new, experimental method of measuring the material damping of test models is presented. The method involves measuring the decay of free vibrations as the model is lofted into free-fall in a vacuum. Vibration signals are transmitted through the vacuum by a miniature telemetry system. The resulting data are recorded and later analyzed using a fast Fourier transform technique to determine the percent critical damping. The experimental apparatus offers a unique means to reset the experiment without breaking the vacuum, which reduces the time between runs.

Edberg, D. L.↗