Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VELOCITY MEASUREMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Final Report on Development of Microwave Resonant Cavity Transducer for Fluid Flow Sensing: Development of Microwave Cavity Flow Meter for Advanced Reactor High Temperature Fluids

We are investigating a microwave resonant cavity transducer for flow sensing in the vessel of a high temperature fluid advanced reactor (AR), such as a molten salt cooled reactor (MSCR) or a sodium fast reactor (SFR). This transducer is a hollow metallic cylindrical cavity, with one of the flat walls of the cylinder flexible enough to undergo microscopic deflection due to dynamic fluid pressure. Membrane deflection leads to a shift in the microwave resonant frequency, which can be detected with a spectrum analyzer. We have developed a continuum electromechanics model of the microwave resonant cavity transducer performance. The deflection of the membrane is calculated using equations from the theory of plates and shells for deflection of radially constrained thin circular disk under uniform load. The microwave frequency shift is calculated using the equations from the microwave cavity perturbation theory. The transducer model was validated with proof-of-concept experimental data of water flow sensing with a Brass 360 right circular cylinder with 22.2mm diameter and 203µm thick wall. The cavity was excited through a subwavelength hole in TE 011 mode with resonant frequency f ≈ 17.8GHz. Subsequently, we have performed a preliminary proof-of-principle test of flow sensing in high temperature liquid sodium in environment. For this test, we have developed a cylindrical resonator with the same dimensions as for the Brass 360 cavity. The resonator for high temperature liquid sodium test was machined from stainless steel 316 and electroplated with silver on the interior surfaces. We have also developed and insertion probe consisting of a 50cm WR-42 brass waveguide enclosed in a protective SS316 tube. The cavity was excited through a subwavelength hole on the side of the wall of the cylinder in the TE 011 mode with resonant frequency f ≈ 17.8GHz. The liquid sodium setup consists of a cylindrical vessel with a center feed line, where a transducer inserted through the top cap of the vessel measures velocity of the impinging liquid jet. The sodium flow sensing study was performed in a liquid sodium vessel at 340°C temperature and ambient pressure. The flow rate was changed by varying sodium pump power, and a frequency shift of several hundred kHz was observed. The transducer was removed after 70 days of testing. No visual damage was observed, and the electromagnetic response remained the same. As a calibration experiment, we have assembled a water vessel with a center feed, and with dimensions similar to those of the liquid sodium setup. Water flow sensing was performed before and after liquid sodium test. The responses in both cases are similar and agree with COMSOL computer simulations. Because long-term (multi-year) experimental tests of transducer resilience to harsh environment are not practical, we have developed a probabilistic model of creep to estimate transducer resilience to the harsh environment. The probabilistic model considers diffusion creep under the condition of high temperature and low stress, where the stress and temperature are allowed to be random variables with Gaussian distributions. Using the probabilistic model, we estimate inelastic membrane deflections due to creep for several temperature ranges. We conclude that for temperatures less than 650°C, creep has negligible long-term effect on the transducer performance.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

TRUST Sensors in Environments: Thermocouples (SE-TC), Release FY25

The Delivery Environments Testbeds to Reduce Uncertainty in Simulations and Tests (TRUST) project is a broad project intended to analyze simplified problems experimentally and with modeling and simulation. The purpose of analyzing these simplified problems is to extend solution methods to more complex problems, as well as understand deficiencies and gaps in knowledge of methods currently used in more complex analyses. The TRUST project encompasses several smaller testbeds intended to isolate individual phenomena. The testbed under consideration in this report is the Sensors in Environments: Thermocouples testbed. In previous years, the purpose of this testbed was to quantify uncertainty of thermocouple sensors. To accomplish this, an aluminum plate was placed in a thermal chamber and subject to various types of thermal loading. Thermocouples were placed in various locations on the aluminum plate in various configurations (e.g., embedded in the plate, placed under Kapton tape), and an effort was made to quantify uncertainty in these measurements. Finite element simulations were performed to investigate how sensitive these measurements were to parameters such as the boundary conditions on the plate and material properties. However, a fundamental source of uncertainty in this analysis was the convective heat transfer from the plate. Convective heat transfer is a complex physical phenomenon comprised of a number of interacting sub-processes and is difficult to predict accurately a priori. As such, the main purpose of this testbed in FY25 was to better understand, both experimentally and numerically, the convective heat transfer from the plate. This is a highly applicable problem to several more complex problems, as convective heat transfer occurs in nearly all problems where a body is moving through air. Numerically, this required a two-step approach. First, the air flow in the thermal chamber was in vestigated using computational fluid dynamics. The commercial solver Fluent was used to perform these simulations. From these simulations, a heat transfer coefficient over the surface of the plate was calculated. This heat transfer was then used as boundary conditions for finite element heat transfer simulations within the plate, which were performed using Abaqus. Significant effort was devoted to automating the handoff between these two solvers. Experimentally, previous thermocouple results in the plate were used to validate the time-dependent thermal profiles produced from Abaqus. Further experimental efforts were performed both to help validate the Fluent simulations and to inform its boundary conditions. For example, hot-wire anemometers were used to measure the velocity in the chamber, which would be particularly useful in understanding the chamber inlet velocity. Thermocouple measurements were also taken in the chamber, instead of only on the plate, to serve as validation evidence for the Fluent simulations. Numerical results showed that the Fluent to Abaqus workflow matched previous plate thermocouple measurements well. This type of handoff is useful for more complex experiments, or those that are not able to be examined in as great of detail as this testbed, as it was performed without any experimental input. Experimental results, however, were more mixed. The anemometers proved unreliable, with inconsistent measurements across all anemometers, even at locations that were nearly identical. On the other hand, the thermocouples provided a relatively rich view of the temperature field in the chamber.

42 ENGINEERING↗

Resource Assessment Study of Long Island Sound Tidal Resource in New York State Waters Based on Numerical Modeling (Abstract)

To refine the understanding of the tidal energy resource in Long Island Sound (LIS), Verdant Power and PNNL will collaborate to conduct a numerical modeling campaign in accordance with a Stage 2 resource assessment according to IEC TC 62600-201. The work will develop a high resolution tidal hydrodynamic model using FVCOM in LIS, validate the model using NOAA C-MIST ADCP data, and conduct a Stage 2 array layout design study at selected hotspots within the project area. The teams will also model tidal energy extraction using the FVCOMTEC module at the hotspot sites, based on specific device technologies provided by Verdant Power. Model results from this study will inform additional resource assessment activities such as in situ water velocity measurements for further model validation and elucidate understanding of other key sites in Long Island Sound for commercial-scale tidal energy deployments.

16 TIDAL AND WAVE POWER↗

Experimental and Numerical Investigation of Flows in Expanding Channels

We present an experimental realization of the classical Jeffery-Hamel flows inside a wedge-shaped channel. We compare the measured velocity fields with the predictions of Jeffery-Hamel theory. A detailed experimental study of bifurcation diagrams for the solutions reveals the absolute stability of the pure outflow solution and an interesting hysteretic structure for bifurcations. We also observe a multiple vortex flow regime predicted earlier numerically and analytically. Experimental studies of the stability of the flow to perturbations at the channel exit are also conducted.

42 ENGINEERING↗

RHOD Site - NOAA PSL Wind Retrievals WINDoe / Derived Data

This dataset contains daily NetCDF files with horizontal wind profiles retrieved with the WINDoe retrieval (Gebauer and Bell 2024) at Rhode Island (RHOD). WINDoe retrievals datasets are also available at Nantucket Island (NANT, nant.windoe.z01.c1) and Block Island (BLOC, bloc.windoe.z01.c1). WINDoe is an optimal estimation algorithm to retrieve wind profiles combining multiple instruments. The code is available in this github repository (https://github.com/OAR-atmospheric-observations/WINDoe/tree/main) and the retrieval is described by Gebauer and Bell (2024). WINDoe allows combining the individual datasets and outputs into one profile taking into account the information and uncertainties of each dataset. The use of WINDoe minimizes data gaps and maximizes data availability, compared to using wind profiles from only one of the instruments. The regular height grid eases comparisons to numerical weather prediction models. Code modifications have been made that include reading in WFIP3 specific instruments, averaging Doppler lidar radial velocities at various azimuth angles to avoid overfitting, and allowing the user to define a height grid by the user in the vipfile. The instruments used as input to the retrieval are a radar wind profiler (low- and high resolution mode) providing data in and above the boundary layer, a scanning Doppler lidar usually providing data throughout the boundary layer, a profiling lidar providing data from 50 to 200 m at BLOC and NANT, and from 10 to 280 m at Rhode Island, and a surface tower (4 m at NANT and RHOD and 10 m at BLOC). From the scanning lidars, we used radial velocity measurements at 60 deg elevation angle at six different azimuth angles with a resolution of approximately 30 m along the line of sight and the lowest range gate at approximately 70 m. The wind profiles are retrieved with WINDoe up to 3.74 km with 10 m vertical resolution. The profiles are retrieved every 15 min at BLOC and NANT and every 60 min at RHOD.

17 WIND ENERGY↗

BLOC Site - NOAA PSL Wind Retrievals WINDoe / Derived Data

This dataset contains daily netcdf files with horizontal wind profiles retrieved with the WINDoe retrieval (Gebauer and Bell 2024) at Block Island (BLOC). WINDoe retrievals datasets are also available at Nantucket Island (NANT, nant.windoe.z01.c1) and Rhode Island (RHOD, rhod.windoe.z01.c1). WINDoe is an optimal estimation algorithm to retrieve wind profiles combining multiple instruments. The code is available in this github repository (https://github.com/OAR-atmospheric-observations/WINDoe/tree/main), and the retrieval is described by Gebauer and Bell (2024). WINDoe allows combining the individual datasets and outputs into one profile taking into account the information and uncertainties of each dataset. The use of WINDoe minimizes data gaps and maximizes data availability, compared to using wind profiles from only one of the instruments. The regular height grid eases comparisons to numerical weather prediction models. Code modifications have been made that include reading in WFIP3 specific instruments, averaging Doppler lidar radial velocities at various azimuth angles to avoid overfitting, and allowing the user to define a height grid by the user in the vipfile. The instruments used as input to the retrieval are a radar wind profiler (low- and high resolution mode) providing data in and above the boundary layer, a scanning Doppler lidar usually providing data throughout the boundary layer, a profiling lidar providing data from 50 to 200 m at BLOC and NANT, and from 10 to 280 m at Rhode Island, and a surface tower (4 m at NANT and RHOD and 10 m at BLOC). From the scanning lidars, we used radial velocity measurements at 60 deg elevation angle at six different azimuth angles with a resolution of approximately 30 m along the line of sight and the lowest range gate at approximately 70 m. The wind profiles are retrieved with WINDoe up to 3.74 km with 10 m vertical resolution. The profiles are retrieved every 15 min at BLOC and NANT and every 60 min at RHOD.

17 WIND ENERGY↗

NANT Site - NOAA PSL Wind Retrievals WINDoe / Derived Data

This dataset contains daily NetCDF files with horizontal wind profiles retrieved with the WINDoe retrieval (Gebauer and Bell 2024) at Nantucket Island (NANT). WINDoe retrievals datasets are also available at Block Island (BLOC, bloc.windoe.z01.c1) and Rhode Island (RHOD, rhod.windoe.z01.c1). WINDoe is an optimal estimation algorithm to retrieve wind profiles combining multiple instruments. The code is available in this github repository (https://github.com/OAR-atmospheric-observations/WINDoe/tree/main), and the retrieval is described by Gebauer and Bell (2024). WINDoe allows combining the individual datasets and outputs into one profile taking into account the information and uncertainties of each dataset. The use of WINDoe minimizes data gaps and maximizes data availability, compared to using wind profiles from only one of the instruments. The regular height grid eases comparisons to numerical weather prediction models. Code modifications have been made that include reading in WFIP3 specific instruments, averaging Doppler lidar radial velocities at various azimuth angles to avoid overfitting, and allowing the user to define a height grid by the user in the vipfile. The instruments used as input to the retrieval are a radar wind profiler (low- and high resolution mode) providing data in and above the boundary layer, a scanning Doppler lidar usually providing data throughout the boundary layer, a profiling lidar providing data from 50 to 200 m at BLOC and NANT, and from 10 to 280 m at Rhode Island, and a surface tower (4 m at NANT and RHOD and 10 m at BLOC). From the scanning lidars, we used radial velocity measurements at 60 deg elevation angle at six different azimuth angles with a resolution of approximately 30 m along the line of sight and the lowest range gate at approximately 70 m. The wind profiles are retrieved with WINDoe up to 3.74 km with 10 m vertical resolution. The profiles are retrieved every 15 min at BLOC and NANT and every 60 min at RHOD.

17 WIND ENERGY↗

Exploration of a Reacting Jet-in-Crossflow in a High-Pressure Axial Stage Combustor

The present work investigates a reacting methane jet in a vitiated cross flow at five atmospheres. The experiments are run at temperatures and velocities relevant to real world gas turbines. High speed chemiluminescence is utilized to obtain flame behavior and visualize flame trajectories. Experimental results are compared with a corresponding RANS CFD model. The characteristics of a diffusion methane jet injected into a vitiated crossflow are explored at various momentum flux ratios and test section inlet boundary conditions. Temperature and velocity measurements are made at the inlet of the test section to ensure uniform boundary conditions for the axial stage. The effect of different momentum flux ratios on flame stabilization mechanisms and jet trajectories are presented. Momentum flux ratios are varied from 0.5-107; at lower momentum flux ratios the diffusion flame is less stable and burns downstream in the shear layer between the jet and crossflow. At higher momentum flux ratios, the diffusion flame burns more upstream and exhibits improved stability compared to the lower momentum flux ratio cases.

03 NATURAL GAS↗

Field Deployment of a Portable Optical Spectrometer for Methane Fugitive Emissions Monitoring on Oil and Gas Well Pads

We present field deployment results of a portable optical absorption spectrometer for localization and quantification of fugitive methane (CH 4 ) emissions. Our near-infrared sensor targets the 2$ν_3$ R(4) CH 4 transition at 6057.1 cm −1 (1651 nm) via line-scanned tunable diode-laser absorption spectroscopy (TDLAS), with Allan deviation analysis yielding a normalized 2.0 ppmv∙Hz −1/2 sensitivity (4.5 × 10 −6 Hz −1/2 noise-equivalent absorption) over 5 cm open-path length. Controlled CH 4 leak experiments are performed at the METEC CSU engineering facility, where concurrent deployment of our TDLAS and a customized volatile organic compound (VOC) sensor demonstrates good linear correlation (R 2 = 0.74) over high-flow (>60 SCFH) CH 4 releases spanning 4.4 h. In conjunction with simultaneous wind velocity measurements, the leak angle-of-arrival (AOA) is ascertained via correlation of CH 4 concentration and wind angle, demonstrating the efficacy of single-sensor line-of-sight (LOS) determination of leak sources. Finally, source magnitude estimation based on a Gaussian plume model is demonstrated, with good correspondence (R 2 = 0.74) between calculated and measured release rates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Orbital Motion of the Wide Planetary-mass Companion GSC 6214-210 b: No Evidence for Dynamical Scattering

Direct-imaging exoplanet surveys have discovered a class of 5–20 M{sub Jup} substellar companions at separations >100 au from their host stars, which present a challenge to planet and star formation models. Detailed analysis of the orbital architecture of these systems can provide constraints on possible formation mechanisms, including the possibility that they were dynamically ejected onto a wide orbit. We present astrometry for the wide planetary-mass companion GSC 6214-210 b (240 au; ≈14 M{sub Jup}) obtained using NIRC2 with adaptive optics at the Keck telescope over 10 years. Our measurements achieved astrometric uncertainties of ≈1 mas per epoch. We determined a relative motion of 1.12 ± 0.15 mas yr{sup −1} (0.61 ± 0.09 km s{sup −1}), the first detection of orbital motion for this companion. We compute the minimum periastron for the companion due to our measured velocity vector and derive constraints on the orbital parameters through our modified implementation of the Orbits for the Impatient rejection sampling algorithm. We find that close periastron orbits, which could indicate that the companion was dynamically scattered, are present in our posterior but have low likelihoods. For all orbits in our posterior, we assess the detectability of close-in companions that could have scattered GSC 6214-210 b from a closer orbit, and find that most potential scatterers would have been detected in previous imaging. We conclude that formation at small orbital separation and subsequent dynamical scattering through interaction with another potential close-in object is an unlikely formation pathway for this companion. We also update stellar and substellar properties for the system using the new parallax from Gaia DR2.

79 ASTRONOMY AND ASTROPHYSICS↗

Explosive Chromospheric Evaporation and Warm Rain in a C3.1 Flare Observed by IRIS, Hinode/EIS, and RHESSI

IRIS and EIS observed a GOES C3.1 flare in stare mode on 2014 March 15. The GOES flare started at 00:21:35 and peaked at 00:26:30 UT. The IRIS slit pointed near the center of the flare, while the EIS slit pointed 35{sup ′′} to its west. About 4 minutes before the GOES flare start, the IRIS C ii and Si iv intensities became (and remained) greater than their pre-flare averages, indicating that the flare had begun and that the chromosphere and transition region were involved. IRIS first detected blueshifted Fe xxi emission at 00:22:42 UT, by which time the C ii and Si iv intensities had increased by factors around 100 and their profiles were redshifted. Simultaneous, cospatial blueshifted Fe xxi emission with redshifted C ii and Si iv emission indicates explosive chromospheric evaporation. EIS spectra reveal Fe xxiii emission that is too weak to measure velocities, and intensity enhancements by factors about 1.7 in the Fe xiv and Fe xvi emission. Lines from both of these coronal ions show redshifts ≈9 km s{sup −1} around 00:24:00 UT, and the Fe xiv 264.7/274.2 intensity ratio reveals an increase of n {sub e} from (1.03±0.20)×10{sup 9} before to (3.58±0.68)×10{sup 9} cm{sup −3} during the flare. The redshifted coronal line emission and increased n {sub e} are consistent with warm rain falling and accumulating in the remote area observed by EIS. A fit to the RHESSI hard X-ray spectrum yields a nonthermal energy injection rate of 4.9×10{sup 26} erg s{sup −1}, from which we estimate a HXR beam energy flux range consistent with explosive evaporation.

79 ASTRONOMY AND ASTROPHYSICS↗

Cluster Cosmology with the Velocity Distribution Function of the HeCS-SZ Sample

We apply the velocity distribution function (VDF) to a sample of Sunyaev–Zel'dovich (SZ)-selected clusters, and we report preliminary cosmological constraints in the ${\sigma }_{8}$-${{\rm{\Omega }}}_{m}$ cosmological parameter space. The VDF is a forward-modeled test statistic that can be used to constrain cosmological models directly from galaxy cluster dynamical observations. The method was introduced in Ntampaka et al. and employs line-of-sight velocity measurements to directly constrain cosmological parameters; it is less sensitive to measurement error than a standard halo mass function approach. The method is applied to the Hectospec Survey of Sunyaev–Zeldovich-Selected Clusters sample, which is a spectroscopic follow-up of a Planck-selected sample of 83 galaxy clusters. Credible regions are calculated by comparing the VDF of the observed cluster sample to that of mock observations, yielding ${{ \mathcal S }}_{8}$ $\equiv \,{\sigma }_{8}{\left({{\rm{\Omega }}}_{m}/0.3\right)}^{0.25}=0.751\pm 0.037$. These constraints are in tension with the Planck Cosmic Microwave Background TT fiducial value, which lies outside of our 95% credible region, but are in agreement with some recent analyses of large-scale structure that observe fewer massive clusters than are predicted by the Planck fiducial cosmological parameters.

79 ASTRONOMY AND ASTROPHYSICS↗

Chasing Accreted Structures within Gaia DR2 Using Deep Learning

In previous work, we developed a deep neural network classifier that only relies on phase-space information to obtain a catalog of accreted stars based on the second data release of Gaia (DR2). In this paper, we apply two clustering algorithms to identify velocity substructure within this catalog. We focus on the subset of stars with line-of-sight velocity measurements that fall in the range of Galactocentric radii $r\in [6.5,9.5]\,{\rm{kpc}}$ and vertical distances $| z| \lt 3\,{\rm{kpc}}$. Known structures such as Gaia Enceladus and the Helmi stream are identified. The largest previously unknown structure, Nyx, is a vast stream consisting of at least 200 stars in the region of interest. This study displays the power of the machine-learning approach by not only successfully identifying known features but also discovering new kinematic structures that may shed light on the merger history of the Milky Way.

Astronomy & Astrophysics↗

Forecasts on the Dark Matter Density Profiles of Dwarf Spheroidal Galaxies with Current and Future Kinematic Observations

We forecast parameter uncertainties on the mass profile of a typical Milky Way dwarf spheroidal galaxy (dSph) using the spherical Jeans equation and Fisher matrix formalism. For a Draco-like system we show that radial velocity measurements for 1000 individual stars can constrain the mass contained within the effective radius of a dSph to within 5%. This is consistent with constraints extracted from current observational data. We compare two systems, a cusp and core, and demonstrate that a minimum sample of 100,000 (10,000) stars with both radial and proper motions measurements is required to disentangle their inner slopes at the 2σ (1σ) level. If using the log-slope measured at the half-light radius as a proxy for differentiating between a core or cusp slope, only 1000 line-of-sight and proper motions measurements are required; however, we show this choice of radius does not always unambiguously differentiate between core and cusped profiles. Once observational errors are below half the value of the intrinsic dispersion, improving the observational precision yields little change in the density profile uncertainties. The choice of priors in our profile shape analysis plays a crucial role when the number of stars in a system is less than 100 but does not affect the resulting uncertainties for larger kinematic samples. Our predicted 2D confidence regions agree well with those from a full likelihood analysis run on a mock kinematic data set taken from the Gaia Challenge, validating our Fisher predictions. Our methodology is flexible, allowing us to predict density profile uncertainties for a wide range of current and future kinematic data sets.

79 ASTRONOMY AND ASTROPHYSICS↗

The Binary Fraction of Stars in the Dwarf Galaxy Ursa Minor via Dark Energy Spectroscopic Instrument

We utilize multi-epoch line-of-sight velocity measurements from the Milky Way Survey of the Dark Energy Spectroscopic Instrument to estimate the binary fraction for member stars in the dwarf spheroidal galaxy Ursa Minor. Our dataset comprises 670 distinct member stars, with a total of more than 2,000 observations collected over approximately one year. We constrain the binary fraction for UMi to be $0.61^{+0.16}_{-0.20}$ and $0.69^{+0.19}_{-0.17}$, with the binary orbital parameter distributions based on solar neighborhood observation from Duquennoy & Mayor (1991) and Moe & Di Stefano (2017), respectively. Furthermore, by dividing our data into two subsamples at the median metallicity, we identify that the binary fraction for the metal-rich ([Fe/H]>-2.14) population is slightly higher than that of the metal-poor ([Fe/H]<-2.14) population. Based on the Moe & Di Stefano model, the best-constrained binary fractions for metal-rich and metal-poor populations in UMi are $0.86^{+0.14}_{-0.24}$ and $0.48^{+0.26}_{-0.19}$, respectively. After a thorough examination, we find that this offset cannot be attributed to sample selection effects. We also divide our data into two subsamples according to their projected radius to the center of UMi, and find that the more centrally concentrated population in a denser environment has a lower binary fraction of $0.33^{+0.30}_{-0.20}$, compared with $1.00^{+0.00}_{-0.32}$ for the subsample in more outskirts.

Qiu, Tian [Shanghai Jiao Tong Univ. (China); DESI ↗

The MOST Hosts Survey: Spectroscopic Observation of the Host Galaxies of ∼40,000 Transients Using DESI

We present the Multi-Object Spectroscopy of Transient (MOST) Hosts survey. The survey is planned to run throughout the 5 yr of operation of the Dark Energy Spectroscopic Instrument (DESI) and will generate a spectroscopic catalog of the hosts of most transients observed to date, in particular all the supernovae observed by most public, untargeted, wide-field, optical surveys (Palomar Transient Factory, PTF/intermediate PTF, Sloan Digital Sky Survey II, Zwicky Transient Facility, DECAT, DESIRT). Science cases for the MOST Hosts survey include Type Ia supernova cosmology, fundamental plane and peculiar velocity measurements, and the understanding of the correlations between transients and their host-galaxy properties. Here we present the first release of the MOST Hosts survey: 21,931 hosts of 20,235 transients. These numbers represent 36% of the final MOST Hosts sample, consisting of 60,212 potential host galaxies of 38,603 transients (a transient can be assigned multiple potential hosts). Of all the transients in the MOST Hosts list, only 26.7% have existing classifications, and so the survey will provide redshifts (and luminosities) for nearly 30,000 transients. A preliminary Hubble diagram and a transient luminosity–duration diagram are shown as examples of future potential uses of the MOST Hosts survey. The survey will also provide a training sample of spectroscopically observed transients for classifiers relying only on photometry, as we enter an era when most newly observed transients will lack spectroscopic classification. The MOST Hosts DESI survey data will be released on a rolling cadence and updated to match the DESI releases.

79 ASTRONOMY AND ASTROPHYSICS↗

A strainmeter array as the fulcrum of novel observatory sites along the Alto Tiberina Near Fault Observatory

Fault slip is a complex natural phenomenon involving multiple spatiotemporal scales from seconds to days to weeks. To understand the physical and chemical processes responsible for the full fault slip spectrum, a multidisciplinary approach is highly recommended. The Near Fault Observatories (NFOs) aim at providing high-precision and spatiotemporally dense multidisciplinary near-fault data, enabling the generation of new original observations and innovative scientific products. The Alto Tiberina Near Fault Observatory is a permanent monitoring infrastructure established around the Alto Tiberina fault (ATF), a 60 km long low-angle normal fault (mean dip 20°), located along a sector of the Northern Apennines (central Italy) undergoing an extension at a rate of about 3 mm yr –1 . The presence of repeating earthquakes on the ATF and a steep gradient in crustal velocities measured across the ATF by GNSS stations suggest large and deep (5–12 km) portions of the ATF undergoing aseismic creep. Both laboratory and theoretical studies indicate that any given patch of a fault can creep, nucleate slow earthquakes, and host large earthquakes, as also documented in nature for certain ruptures (e.g., Iquique in 2014, Tōhoku in 2011, and Parkfield in 2004). Nonetheless, how a fault patch switches from one mode of slip to another, as well as the interaction between creep, slow slip, and regular earthquakes, is still poorly documented by near-field observation. With the strainmeter array along the Alto Tiberina fault system (STAR) project, we build a series of six geophysical observatory sites consisting of 80–160 m deep vertical boreholes instrumented with strainmeters and seismometers as well as meteorological and GNSS antennas and additional seismometers at the surface. By covering the portions of the ATF that exhibits repeated earthquakes at shallow depth (above 4 km) with these new observatory sites, we aim to collect unique open-access data to answer fundamental questions about the relationship between creep, slow slip, dynamic earthquake rupture, and tectonic faulting.

58 GEOSCIENCES↗

Large-Eddy Simulation Sensitivities to Variations of Configuration and Forcing Parameters in Canonical Boundary-Layer Flows for Wind Energy Applications

Here, the sensitivities of idealized Large-Eddy Simulations (LES) to variations of model configuration and forcing parameters on quantities of interest to wind power applications are examined. Simulated wind speed, turbulent fluxes, spectra and cospectra are assessed in relation to variations of two physical factors, geostrophic wind speed and surface roughness length, and several model configuration choices, including mesh size and grid aspect ratio, turbulence model, and numerical discretization schemes, in three different code bases. Two case studies representing nearly steady neutral and convective atmospheric boundary layer (ABL) flow conditions over nearly flat and homogeneous terrain were used to force and assess idealized LES, using periodic lateral boundary conditions. Comparison with fast-response velocity measurements at five heights within the lowest 50 m indicates that most model configurations performed similarly overall, with differences between observed and predicted wind speed generally smaller than measurement variability. Simulations of convective conditions produced turbulence quantities and spectra that matched the observations well, while those of neutral simulations produced good predictions of stress, but smaller than observed magnitudes of turbulence kinetic energy, likely due to tower wakes influencing the measurements. While sensitivities to model configuration choices and variability in forcing can be considerable, idealized LES are shown to reliably reproduce quantities of interest to wind energy applications within the lower ABL during quasi-ideal, nearly steady neutral and convective conditions over nearly flat and homogeneous terrain.

17 WIND ENERGY↗