Effects of Thermal Aging and Manufacture Induced Stress on Structure Integrity and Performance of TE Module.
Abstract not provided.
Lu, Wei-Yang↗
SEARCH · Engineering Papers
Results for “THERMAL STRESSES”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
ADVANCED WELDING TECHNOLOGY DEVELOPMENT FOR NUCLEAR REACTOR REPAIR
Welding is widely used for repair, maintenance, and upgrade of nuclear reactor components. As a critical technology for supporting the extension of nuclear power plant service lifetimes beyond 60 years, there has been an industry need in further developing welding technology for highly irradiated materials. During welding of irradiated materials, Helium, which is a transmutation byproduct from Boron and Nickel contained in the structural alloys, can coalesce into bubbles along grain boundaries in the material under driving forces of high temperature and thermal tensile stress. This leads to embrittlement and potential intergranular cracking in the Heat Affected Zone (HAZ) of the weld. In this paper, irradiated 304 stainless steel coupons containing 5, 10 and 20 ppm Boron prior to radiation were successfully welded by advanced laser beam welding (LBW) and friction stir welding (FSW). Facilities and welding machine design, welding processes development, cold material welded joints evaluation, process safety control and documentation, and irradiated material welding are discussed. Both laser and friction stir welded coupons of the irradiated material exhibited high welding quality and surface finish. No Helium induced welding defects were observed on the weld surfaces or adjacent base metals.
Tang, Wei↗
Assessment of failure modes of monolithic fuel plates
Monolithic fuel is a fuel form that is considered for the conversion of high performance research reactors. In order to qualify this new fuel system, the fuel plates should meet the safety standards and perform well in reactor. The fuel system must maintain its mechanical integrity, sustain a geometric stability and should have stable and predictable irradiation behavior. The requirement to maintain mechanical integrity under normal operating conditions is primarily demonstrated by a successful testing of fuel plates up to the limiting conditions defined by the fuel performance envelope, including an adequate margin. Although large number of plates have been tested with satisfactory thermo-mechanical performance, post-irradiation examination of plates from previous RERTR-12 experiments have revealed that pillowing occurred in several plates, rendering performance of these plates unacceptable. To address such failures, efforts are underway to define the mechanisms responsible for the in-reactor pillowing, and suggest improvements to the fuel plate design and operational envelope. For this purpose, selected plates from previous experiments were simulated to understand the thermo-mechanical response of the plates to the fission density and thermally induced stresses. Simulation results were then comparatively evaluated with post-irradiation examinations of selected plates. The simulation results and experimental observations established a possible correlation between failure by plate pillowing, high porosity and a presence of tensile stress state. The study has implied that porosity leading to degradation of material properties, accompanied by a sufficiently large tensile stress state can lead to a pillowing-type failure at reactor shutdown. This paper presents these findings, discusses such failure modes, and the influence of fuel burn-up and power on the magnitude of the shutdown-induced tensile stresses.
42 ENGINEERING↗
Quenching and Thermal Distortion Behavior of a Uranium Alloy Part - Experiments and Modeling
Explore the source record for details and available documents.
Phase Transformations, Thermal Stress, Heat Transf↗
In situ irradiation of spent nuclear fuels
To improve the economics of commercial nuclear reactors, nuclear vendors and utilities are seeking approval for increased burnup usage of the existing nuclear fleet. This is especially critical for meeting the clean energy initiative by the United States Government, Department of Energy (DOE). However, one of the key challenges the nuclear industry faces in this regard is that the regions exposed to high burnup and low temperatures exhibit a fine-grained microstructure with large bubbles known as high-burnup structure (HBS) [1]. The formation of HBS has been correlated to the diminished performance of the reactor, as well as fuel fragmentation and pulverization during transient and accidental conditions [2]. Therefore, it is paramount to understand the mechanisms for HBS formation along with its impact on the properties and performance of nuclear fuels. While existing programs, such as Nuclear Energy Advanced Modeling and Simulation (NEAMS) and Advanced Fuel Campaign (AFC) are focusing on evaluating the performance impact of HBS, the physical mechanisms contributing to HBS formation are still not fully understood. In addition, having predictive capabilities and sound understanding of the microstructural evolution of nuclear fuel is essential for accelerated development, qualification, and deployment of new nuclear materials and novel reactor designs for advanced nuclear reactors. There is a lack of consensus among researchers regarding the mechanisms leading to such restructuring observed in HBS. Grain subdivision due to polygonization versus recrystallization, continuous versus discrete recrystallization occurring in tandem or conjunction, etc., have been proposed and debated. In general, it is hypothesized that defect accumulation and dislocation interaction within the grains cause the realignment of dislocations into grain boundaries, leading to the new subgrain formation, which over time transforms into new grains. However, due to the lack of transient data, the importance of fission rate, irradiation, thermal, and stress history of the fuel on the restructuring could not be assessed. In situ microstructural evolution under various irradiation conditions is desired to bridge this gap. Alternatively, phase-field-based models have been developed to capture HBS formation via discrete recrystallization utilizing the classical nucleation approach [3–5]. However, in these models, the grain nucleation criteria are often defined based on empirical relations for burnup and fission gas density leading to dislocation density change. A mechanistic approach to capture the dislocation interaction with the microstructural features leading to grain subdivision is lacking.
11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
A uniaxial stress capacitive dilatometer for high-resolution thermal expansion and magnetostriction under multiextreme conditions
Thermal expansion and magnetostriction are directional dependent thermodynamic quantities. For the characterization of novel quantum phases of matter, it is required to study materials under multi-extreme conditions, in particular, down to very low temperatures, in very high magnetic fields or under high pressure. We developed a miniaturized capacitive dilatometer suitable for temperatures down to 20 mK and usage in high magnetic fields, which exerts a large spring force between 40 to 75 N on the sample. This corresponds to a uniaxial stress up to 3 kbar for a sample with cross section of (0.5 mm){sup 2}. We describe design and performance test of the dilatometer which resolves length changes with high resolution of 0.02 Å at low temperatures. The miniaturized device can be utilized in any standard cryostat, including dilution refrigerators or the commercial physical property measurement system.
46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
The competition between thermal contraction and differentiation in the stress history of the moon
The stress history of the moon is discussed, taking into consideration the effects of thermal contraction and differentiation. The amount of expansion caused by extracting basalt from undifferentiated lunar material is estimated taking account of the uncertainty in the knowledge of the appropriate compositions, and the resulting estimate of the expansion is used to compare the relative importance of the thermal and differentiation effects in the moon's volumetric history. The results of calculations show that differentiation is likely to be of major importance and, thus, thermal expansion is not the sole possible contributor to evolutionary changes in the lunar radius.
Kirk, Randolph L.↗
Analysis of thermal and mechanical properties with inventory level of the molten salt storage tank in central receiver concentrating solar power plants
Molten salt thermal energy storage (TES) tanks ensure steady power output of concentrating solar power (CSP) plants; however, recent tank failures have highlighted the need for further analysis. Current studies primarily focus on analyzing the molten salt flow, heat transfer, and thermal efficiency. Additionally, research on the latest tank structures is limited and lacks newest experimental validation. This study measures temperature and molten salt inventory levels in the high-temperature tank at a 50 MW central receiver CSP plant, connected to the power grid in 2019. A multi-physics model was developed to evaluate thermal and mechanical properties of TES tanks by combining computational fluid dynamics and finite element modeling using real plant data. Heat loss, temperature, displacement, and stress distribution of the tank at different inventory levels were investigated. Results show that ambient air velocity near the tank roof reaches 2.14 m/s, much higher than 0.2 m/s near the wall. The temperatures of inventory fluid and tank are close, varying slightly at different levels due to thermal conduction and radiation. Because the heat loss strongly depends on temperature, the total tank loss remains nearly constant across inventory levels. Larger temperature gradients and thermal stresses are primarily localized along the tank floor edge and the air-salt interface. Notably, the maximum thermal stress at the tank edge is three times higher than that at the interface. The magnitude of total stress changes by less than 5 MPa with and without thermal load, indicating that high temperatures exert only a minor impact on tank stress. In contrast, thermal load significantly affects tank deformation, particularly at the roof edge, where values exceed 150 mm. Despite the large variation in molten salt levels, tank wall temperatures and displacements present a minor change, suggesting a weak correlation with inventory levels. In conclusion, the findings obtained in this study provide important insights on the TES tank that could be used to optimize tank design and operation strategies.
14 SOLAR ENERGY↗
Local stresses in metal matrix composites subjected to thermal and mechanical loading
An elasticity solution has been used to analyze matrix stresses near the fiber/matrix interface in continuous fiber-reinforced metal-matrix composites, modeling the micromechanics in question in terms of a cylindrical fiber and cylindrical matrix sheath which is embedded in an orthotropic medium representing the composite. The model's predictions for lamina thermal and mechanical properties are applied to a laminate analysis determining ply-level stresses due to thermomechanical loading. A comparison is made between these results, which assume cylindrical symmetry, and the predictions yielded by a FEM model in which the fibers are arranged in a square array.
Highsmith, Alton L.↗
Spacecraft structural concepts.
Thermal strains, deformations, stresses and fluctuating and static pressures on spacecraft in terms of structural design and material selection
STRUCTURAL STRAIN↗
Resizing procedure for structures under combined mechanical and thermal loading
The fully-stressed design (FSD) appears to be the most widely used approach for sizing of flight structures under strength and minimum-gage constraints. Almost all of the experience with FSD has been with structures primarily under mechanical loading as opposed to thermal loading. In this method the structural sizes are iterated with the step size, depending on the ratio of the total stress to the allowable stress. In this paper, the thermal fully-stressed design (TFSD) procedure developed for problems involving substantial thermal stress is extended to biaxial stress members using a Von Mises failure criterion. The TFSD resizing procedure for uniaxial stress is restated and the new procedure for biaxial stress members is developed. Results are presented for an application of the two procedures to size a simplified wing structure.
Adelman, H. M.↗
Residual thermal and moisture influences on the strain energy release rate analysis of edge delamination
A laminated plate theory analysis is developed to calculate the strain energy release rate associated with edge delamination growth in a composite laminate. The analysis includes the contribution of residual thermal and moisture stresses to the strain energy released. The strain energy release rate, G, increased when residual thermal effects were combined with applied mechanical strains, but then decreased when increasing moisture content was included. A quasi-three-dimensional finite element analysis indicated identical trends and demonstrated these same trends for the individual strain energy release rate components, G sub I and G sub II, associated with interlaminar tension and shear. An experimental study indicated that for T300/5208 graphite-epoxy composites, the inclusion of residual thermal and moisture stresses did not significantly alter the calculation of interlaminar fracture toughness from strain energy release rate analysis of edge delamination data taken at room temperature, ambient conditions.
Obrien, T. K.↗
Residual thermal and moisture influences on the strain energy release rate analysis of edge delamination
A laminated plate theory analysis is developed to calculate the strain energy release rate associated with edge delamination growth in a composite laminate. The analysis includes the contribution of residual thermal and moisture stresses to the strain energy released. The strain energy release rate, G, increased when residual thermal effects were combined with applied mechanical strains, but then decreased when increasing moisture content was included. A quasi-three-dimensional finite element analysis indicated identical trends and demonstrated these same trends for the individual strain energy release rate components, G sub I and G sub II, associated with interlaminar tension and shear. An experimental study indicated that for T300/5208 graphite-epoxy composites, the inclusion of residual thermal and moisture stresses did not significantly alter the calculation of interlaminar fracture toughness from strain energy release rate analysis of edge delamination data taken at room temperature, ambient conditions.
Obrien, T. K.↗
Stress Analyzer
SPATE 900 Dynamic Stress Analyzer is an acronym for Stress Pattern Analysis by Thermal Emission. It detects stress-induced temperature changes in a structure and indicates the degree of stress. Ometron, Inc.'s SPATE 9000 consists of a scan unit and a data display. The scan unit contains an infrared channel focused on the test structure to collect thermal radiation, and a visual channel used to set up the scan area and interrogate the stress display. Stress data is produced by detecting minute temperature changes, down to one-thousandth of a degree Centigrade, resulting from the application to the structure of dynamic loading. The electronic data processing system correlates the temperature changes with a reference signal to determine stress level.
Source record↗
UV Curable Polyimides
The development of UV curable polyimides for high-temperature applications is a growing area of research activity. The objective of this technology is an attempt to bypass many of the issues associated with "typical" high-temperature polymers. For example, the use of toxic or mutagenic monomers (i.e., many aromatic diamines) can be prevented. Also, it proves to be a viable means in circumventing the problems associated with high-processing temperature of polymers, which cause thermally induced processing stresses (i.e., microcracking). The approach that we have been pursuing is Diels-Alder Polymerization. In this approach, we are generating dienes with light instead of heat. This process is called photoenolization. Several bismaleimides and bisacrylates are used as the dienophiles. The method is fairly general and a wide variety of diketones and bismaleimides can be used. UV curability processes are advantageous due to the following: (1) With such a wide variety of monomers, it allows for the use of nontoxic/nonmutagenic monomers; (2) Polyimides cure at room temperature, which reduces thermally induced stresses; (3) It reduces processing and tooling cost; (4) There are many potential applications for this technology, i.e., thin films as alignment layers for LC displays, photoresists, and photonic material as well as a potential market for use as adhesives.
Meador, Michael↗
Laboratory system for studying cryogenic thermal rock fracturing for well stimulation
The concept of cryogenic fracturing is that a sharp thermal gradient developed by applying a cryogenic fluid on a rock surface causes a strong local tensile stress that initiates fractures. Prior field tests suggest that field application with special equipment rated for cryogenic temperatures may deliver potential benefits. The tests did not, however, identify the fracture mechanisms at work in downhole conditions. We present our laboratory designs and procedures developed for studying cryogenic fracturing mechanisms in a well environment, and examine typical data indicative of the performance of the system. The experimental apparatus and procedures were specifically designed to conduct cryogenic fracturing tests in specimens under confining stress, with integrated cryogen transport, measurements, and fracture characterization. A true-triaxial loading system was built to simulate reservoir stress levels and anisotropic stress application, and was designed to avoid thermal stresses in tests involving cryogen by arranging discrete components in an open chamber. To maximize thermal shock on the wellbore surface, tubing and wellhead are configured so that liquid nitrogen enters the borehole and flow out after contributing to thermal shock. The temperature at boreholes and along flow lines, borehole pressure, and liquid nitrogen consumption are monitored throughout treatments. Acoustic transmission and pressure-decay measurements are used to characterize fractures before and after the experiments. Breakdown tests performed on un-stimulated specimens and stimulated specimens compare breakdown pressures of the two groups and thus evaluate the performance of thermal fracturing. The laboratory design was able to effectively apply cryogenic stimulations to laboratory rock specimens. Finally, the characterization methods were able to capture fracture creation and rock property changes due to cryogenic fracturing.
54 ENVIRONMENTAL SCIENCES↗
Remote sensing implications of changes in physiologic structure and function of tree seedlings under moisture stress
Spectral reflectance and thermal emission of conifer and hardwood leaves under moisture stress
Olson, C. E., Jr.↗
Techniques for controlling warpage and residual stresses in welded structures
Thermal pattern alteration technique controls both distortion and residual stresses in aluminum weldments. Cryogenic liquids and auxiliary heat sources are used to produce contraction and expansion of metal in the vicinity of the weld in such a manner as to counterbalance expansion and contraction caused by welding.
Cole, D. Q.↗