Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Surface analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Real time thermal imaging for analysis and control of crystal growth by the Czochralski technique

A real time thermal imaging system with temperature resolution better than +/- 0.5 C and spatial resolution of better than 0.5 mm has been developed. It has been applied to the analysis of melt surface thermal field distributions in both Czochralski and liquid encapsulated Czochralski growth configurations. The sensor can provide single/multiple point thermal information; a multi-pixel averaging algorithm has been developed which permits localized, low noise sensing and display of optical intensity variations at any location in the hot zone as a function of time. Temperature distributions are measured by extraction of data along a user selectable linear pixel array and are simultaneously displayed, as a graphic overlay, on the thermal image.

Wargo, M. J.↗
NASA NTRS1992

Resonant behaviour of MHD waves on magnetic flux tubes. III - Effect of equilibrium flow

The Hollweg et al. (1990) analysis of MHD surface waves in a stationary equilibrium is extended. The conservation laws and jump conditions at Alfven and slow resonance points obtained by Sakurai et al. (1990) are generalized to include an equilibrium flow, and the assumption that the Eulerian perturbation of total pressure is constant is recovered as the special case of the conservation law for an equilibrium with straight magnetic field lines and flow along the magnetic field lines. It is shown that the conclusions formulated by Hollweg et al. are still valid for the straight cylindrical case. The effect of curvature is examined.

Goossens, Marcel↗
NASA NTRS1991

Long-term changes in composition of solar particles implanted in extraterrestrial materials

Analysis of lunar surface samples for elements implanted therein by solar corpuscular radiation reveals evidence for the following compositional changes over a time period between 1.5 and 3 Gyr: 50-percent decreases in the ratios He-4/Ar-36 and Xe/Ar-36; a 20-percent increase in the ratio He-3/He-4; a 3-percent increase in the ratio Ne-20/Ne-22; and a 50-percent increase in the ratio N-15/N-14. The causes of these changes are not resolved at this time but may include (1) a change in acceleration conditions of the solar wind, (2) a change in flux of solar energetic particles relative to that of the solar wind, and (3) a change in composition of the solar convective zone. There is good evidence for a long-term decrease in the solar-wind flux.

Kerridge, J. F.↗
NASA NTRS1991

Determination of design and operation parameters for upper atmospheric research instrumentation to yield optimum resolution with deconvolution

The final report for work on the determination of design and operation parameters for upper atmospheric research instrumentation to yield optimum resolution with deconvolution is presented. Papers and theses prepared during the research report period are included. Among all the research results reported, note should be made of the specific investigation of the determination of design and operation parameters for upper atmospheric research instrumentation to yield optimum resolution with deconvolution. A methodology was developed to determine design and operation parameters for error minimization when deconvolution is included in data analysis. An error surface is plotted versus the signal-to-noise ratio (SNR) and all parameters of interest. Instrumental characteristics will determine a curve in this space. The SNR and parameter values which give the projection from the curve to the surface, corresponding to the smallest value for the error, are the optimum values. These values are constrained by the curve and so will not necessarily correspond to an absolute minimum in the error surface.

Ioup, George E.↗
NASA NTRS1990

Automation and robotics human performance

The scope of this report is limited to the following: (1) assessing the feasibility of the assumptions for crew productivity during the intra-vehicular activities and extra-vehicular activities; (2) estimating the appropriate level of automation and robotics to accomplish balanced man-machine, cost-effective operations in space; (3) identifying areas where conceptually different approaches to the use of people and machines can leverage the benefits of the scenarios; and (4) recommending modifications to scenarios or developing new scenarios that will improve the expected benefits. The FY89 special assessments are grouped into the five categories shown in the report. The high level system analyses for Automation & Robotics (A&R) and Human Performance (HP) were performed under the Case Studies Technology Assessment category, whereas the detailed analyses for the critical systems and high leverage development areas were performed under the appropriate operations categories (In-Space Vehicle Operations or Planetary Surface Operations). The analysis activities planned for the Science Operations technology areas were deferred to FY90 studies. The remaining activities such as analytic tool development, graphics/video demonstrations and intelligent communicating systems software architecture were performed under the Simulation & Validations category.

Mah, Robert W.↗
NASA NTRS1992

Geologic evolution of the east rim of the Hellas basin, Mars

The east rim of the Hellas basin, one of the largest obvious impact features on Mars, is studied. The distribution of geologic materials in the region is documented, and their modes of origin are constrained based on their geomorphologic characteristics. Superposition relationship and crater size-frequency distributions allow the relative ages of the geologic units to be determined and provide information regarding the timing and extent of the geologic processes emplacing and modifying the surface materials. Systematic analysis of the degradation of the Hellas basin is used to illustrate the sequence of events and interplay of geologic processes which control the evolution of many regions on Mars.

Crown, David A.↗
NASA NTRS1993

Investigation of a hypersonic crossing shock wave/turbulent boundary layer interaction

A combined theoretical and experimental study is presented for the interaction between crossing shock waves generated by (10 deg, 10 deg) sharp fins and a flat plate turbulent boundary layer at Mach 8.3. The theoretical model is the full 3D mean compressible Reynolds-averaged Navier-Stokes (RANS) equations incorporating the algebraic turbulent eddy viscosity model of Baldwin and Lomax (1978). A grid refinement study indicated that adequate resolution of the flow field has been achieved. Computed results agree well with experiment for surface pressure and surface flow patterns and for pitot pressure and yaw angle profiles in the flow field. The computations, however, significantly overpredict surface heat transfer. Analysis of the computed flow field results indicates the formation of complex streamline and wave structures within the interaction region.

Narayanswami, N↗
NASA NTRS1948

Residual Stress Analysis of Overspeeded Disk with Central Hole by X-ray Diffraction

An X-ray - diffraction analysis of residual surface stresses after plastic strain was introduced in a parallel-sided 3S-O aluminum disk with a central hole by two types of centrifugal overspeed is reported. Both tangential and radial stresses were generally tensile with large local variations near the hole where surface stresses may have been partly superficial. These stresses were both tensile and compressive dependent on the distance from the disk center when mass compression was effected near the hole.

ALUMINUM↗
NASA NTRS1990

Space vehicle deployment from Space Station

When launching a spacecraft from Earth parking orbit to deep space, it is highly desirable to have the hyperbolic excess velocity vector (v-infinity) contained in the parking orbit plane. Ground launches can force the parking orbit plane to contain the v-infinity vector by using launch azimuth and lift-off time as independent variables. When launching from the Space Station, a new set of variables comes into play. The Space Station orbit is of fixed inclination but precessing due to the Earth's oblateness. Its plane will seldom (and may never) contain the desired v-infinity vector. Consequently, the departure strategy will usually require multiple burns and include a plane change. Also, the concept of 'launch window' will be somewhat different from Earth surface launches. An analysis of the deployment of interplanetary spacecraft from the Space Station is described, with emphasis on the effect of the trajectory characteristics on station operations. Several planetary mission types are analyzed, including manned Mars missions and unmanned high declination departures. The constraint of Space Station orbit nodal position is quantified and the operational implications for Space Station reboost strategy are examined.

Henry, Paul K.↗
NASA NTRS1993

Opportunity for early science return by the Artemis Program

The purpose of the Artemis Program is to gather vital scientific and engineering data by conducting robotic exploration missions on the lunar surface both prior to and concurrent with human missions. The Artemis Program includes rapid, near-term development of a variety of small experimental and operational payloads, a low-cost capacity to deliver these payloads to any location on the lunar surface, and the analysis of the data returned. The Artemis Program will provide opportunities to improve the understanding of lunar geosciences, to demonstrate the Moon's unique capacity as an astronomical platform to study the universe, to conduct scientific and technology development experiments, and to prepare for and complement human missions.

Meyer, Charles↗
NASA NTRS1993

Groundbased monitoring of Martian atmospheric opacity

The amount of dust in the Martian atmosphere is variable in both space and time. The presence of aerosols in the Mars atmosphere complicates quantitative analysis of Martian surface properties. We have developed a model for Mars surface and atmospheric scattering based on equations in Hillier et al (1991). This formulation was chosen for its speed of computation and because it accounts for the spherical geometry of atmospheric scattering at high mission angles, i.e., near the planetary limb.

Herkenhoff, K. E.↗
NASA NTRS1994

Hubble Space Telescope photometry of the central regions of Virgo Cluster elliptical galaxies. 1: Observations, discussion, and conclusions

Using the Hubble Space Telescope we have observed at 10 pc resolution the nuclei of a luminosity-limited sample of 14 E and E/SO galaxies in the Virgo Cluster with magnitudes B(sub T) = 9.4 to 13.4. In this paper we present the images, and discuss the results of the detailed analysis of the surface photometry given in two companion papers. We find that the nuclear and near-nuclear morphologies confirm and strengthen the previously recognized dichotomy of 'E' galaxies into 'true' and 'disky' subtypes. The latter, usually classified E4 or later, often show a bright nuclear disk of radius approximately 100 pc. Essentially all early-type galaxies with -18 greater than M(sub B) greater than -20 are disky. Most true E galaxies are classified E4 or earlier. Most galaxies of both types show dust in the nuclear regions, the most remarkable example being a compact dust disk in NGC 4261. Other than dust, no anomalies were detected in the centers of the three galaxies in our sample which show clear kinematic evidence for a decoupled component.

Jaffe, Walter↗
NASA NTRS1994

Gravity waves in Titan's atmosphere

Scintillations (high frequency variations) observed in the radio signal during the occultation of Voyager 1 by Titan (Hinson and Tyler, 1983) provide information concerning neutral atmospheric density fluctuations on scales on hundreds of meters to a few kilometers. Those seen at altitudes higher than 25 km above the surface were interpreted by Hinson and Tyler as being caused by linear, freely propagating (energy-conserving) gravity waves, but this interpretation was found to be inconsistent with the scintillation data below the 25-km altitude level. Here an attempt is made to interpret the entire scintillation profile between the surface and the 90-km altitude level in terms of gravity waves generated at the surface. Numerical calculations of the density fluctuations caused by two-dimensional, nonhydrostatic, finite-amplitude gravity waves propagating vertically through Titan's atmosphere are performed to produce synthetic scintillation profiles for comparison with the observations. The numerical model accurately treats the effects of wave transience, nonlinearity, and breakdown due to convective instability in the overturned part of the wave. The high-altitude scintillation data were accurately recovered with a freely propagating wave solution, confirming the analytic model of Hinson and Tyler. It is found that the low-altitude scintillation data can be fit by a model where a component of the gravity waves becomes convectively unstable and breaks near the 15 km level. The large-scale structure of the observed scintillation profile in the entire altitude range between 5 and 85 km can be simulated by a model where the freely propagating and breaking waves are forced at the surface simultaneously. Further analysis of the Voyager 1 Titan low-altitude scintillation data, using inversion theory appropriate for strong scattering, could potentially remove some of the ambiguities remaining in this analysis and allow a better determination of the strength and source of the waves.

Friedson, A. James↗
NASA NTRS1993

Analysis of rapidly developing fog at the Kennedy Space Center

Space Shuttle landings at Kennedy Space Center (KSC) are of special concern to NASA's landing community because of Florida's rapidly changing weather conditions. Since a large number of Shuttle landing attempts occur in the morning hours (just after sunrise) fog and stratus development are a problem. The deorbit burn decision for a landing at KSC is typically made 90 minutes before Shuttle touchdown. In that 90 minutes weather conditions can change very rapidly. Fog to the west of KSC an advect in and reduce visibility to less than 7 miles. The most important difference between Shuttle and normal aircraft landings is that the Shuttle has no go-around capability requiring a forecast with little room for error. To help guard against rapidly changing weather conditions, flight rules have been developed as guidelines for all landings. This paper concerns fog development that would affect less than 7-statue mile visibility rule which is in effect for End-Of-Mission (EOM) Shuttle landings at KSC (Rule 4-64(A)). Data used for this analysis included hourly surface observations at the X68 Shuttle Landing Facility (SLF) and upper-air observations form the CCAFS (Cape Canaveral Air Force Station-72794) rawinsonde site for the five year period, 1986 to 1990. This investigation focused on rapidly developing fog or stratus that developed between decision time and landing.

Wheeler, Mark M.↗
NASA NTRS1995

Duplication and analysis of meteoroid damage on LDEF and advanced spacecraft materials

The analysis of exposed surfaces on LDEF since its retrieval in 1990 has revealed a wide range of meteoroid and debris (M&D) impact features in the sub-micron to millimeter size range, ranging from quasi-infinite target cratering in LDEF metallic structural members (e.g. inter-costals, tray clamps, etc.) to non-marginal perforations in metallic experimental surfaces (e.g. thin foil detectors, etc.). Approximately 34,000 impact features are estimated to exist on the exposed surfaces of LDEF. The vast majority of impact craters in metal substrates exhibit circular footprints, with approximately 50 percent retaining impactor residues in varying states of shock processing. The fundamental goals of this project were to duplicate and analyze meteoroid impact damage on spacecraft metallic materials with a view to quantifying the residue retention and oblique impact morphology characteristics. Using the hypervelocity impact test facility established at Auburn University a series of impact tests (normal and oblique incidence) were executed producing consistently high (11-12 km/s) peak impact velocities, the results of which were subsequently analyzed using Scanning Electron Microscope (SEM) and Energy Dispersive X-ray Spectroscopy (EDXS) facilities at Auburn University.

Hill, David C.↗
NASA NTRS1992

Investigation of advanced propulsion technologies: The RAM accelerator and the flowing gas radiation heater

The two principal areas of advanced propulsion investigated are the ram accelerator and the flowing gas radiation heater. The concept of the ram accelerator is presented as a hypervelocity launcher for large-scale aeroballistic range applications in hypersonics and aerothermodynamics research. The ram accelerator is an in-bore ramjet device in which a projectile shaped like the centerbody of a supersonic ramjet is propelled in a stationary tube filled with a tailored combustible gas mixture. Combustion on and behind the projectile generates thrust which accelerates it to very high velocities. The acceleration can be tailored for the 'soft launch' of instrumented models. The distinctive reacting flow phenomena that have been observed in the ram accelerator are relevant to the aerothermodynamic processes in airbreathing hypersonic propulsion systems and are useful for validating sophisticated CFD codes. The recently demonstrated scalability of the device and the ability to control the rate of acceleration offer unique opportunities for the use of the ram accelerator as a large-scale hypersonic ground test facility. The flowing gas radiation receiver is a novel concept for using solar energy to heat a working fluid for space power or propulsion. Focused solar radiation is absorbed directly in a working gas, rather than by heat transfer through a solid surface. Previous theoretical analysis had demonstrated that radiation trapping reduces energy loss compared to that of blackbody receivers, and enables higher efficiencies and higher peak temperatures. An experiment was carried out to measure the temperature profile of an infrared-active gas and demonstrate the effect of radiation trapping. The success of this effort validates analytical models of heat transfer in this receiver, and confirms the potential of this approach for achieving high efficiency space power and propulsion.

Bruckner, A. P.↗
NASA NTRS1996

Thermocapillary Bubble Migration: Thermal Boundary Layers for Large Marangoni Numbers

The migration of an isolated gas bubble in an immiscible liquid possessing a temperature gradient is analyzed in the absence of gravity. The driving force for the bubble motion is the shear stress at the interface which is a consequence of the temperature dependence of the surface tension. The analysis is performed under conditions for which the Marangoni number is large, i.e. energy is transferred predominantly by convection. Velocity fields in the limit of both small and large Reynolds numbers are used. The thermal problem is treated by standard boundary layer theory. The outer temperature field is obtained in the vicinity of the bubble. A similarity solution is obtained for the inner temperature field. For both small and large Reynolds numbers, the asymptotic values of the scaled migration velocity of the bubble in the limit of large Marangoni numbers are calculated. The results show that the migration velocity has the same scaling for both low and large Reynolds numbers, but with a different coefficient. Higher order thermal boundary layers are analyzed for the large Reynolds number flow field and the higher order corrections to the migration velocity are obtained. Results are also presented for the momentum boundary layer and the thermal wake behind the bubble, for large Reynolds number conditions.

Balasubramaniam, R.↗
NASA NTRS1997

An Experimental Investigation on the Static Equilibria and Dynamics of Liquid Bridges

A liquid bridge is a volume of liquid held between two or more solid supports. In the case of small disk supports with a sharp edge, the contact line between the bridge and the support disk will be anchored along the edge of the disk. For these cases the solid presents a geometrical singularity and the contact angle is indeterminate within a given range. This dissertation presents research conducted on liquid bridges with anchored contact lines. The three major topics covered are: determining the role of support geometry on static equilibria, liquid bridge dynamical behavior, and forces exerted by a liquid bridge on a support structure. The work was primarily experimental and conducted in a "Plateau tank" that allowed for the simulation of equivalent low-gravity conditions. The main thrust of the experimental work involved the use of a high resolution optical measurement system for imaging the dynamic zone shape, measurement of the static and dynamic contact angles and non-invasive analysis of excited surface modes. The liquid bridge was manipulated by computer controlled linear actuators which allowed precise control over the physical characteristics of the bridge. Experiments have been carried out to locate a bifurcation point along the maximum volume axisymmetric stability margin. Below the critical slenderness the bifurcation from an axisymmetric to a stable nonaxisymmetric configuration is supercritical. However, above this critical slenderness, the bifurcation is subcritical. A series of experiments analyzed the effect on axisymmetric bridge stability by using support disks of different radii, The shape behavior as transition points were approached, as well as the limiting case of a vanishing support radius was investigated. Experiments were performed to determine the resonant frequencies of axisymmetric bridges subject to lateral vibrations. Anomolous results led to a series of experiments to characterize nonlinearities present in the dynamic bridge shape. Finally, an attempt was made to experimentally measure the force exerted by the bridge on the lower support disk. This was done through use of a force balance apparatus. Particular attention was paid to the behavior of the bridge as the minimum volume stability limit was approached.

Resnick, Andrew Howard↗