Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

The use of a simplified structural model as an aid in the strain gage calibration of a complex wing

The use of a relatively simple structural model to characterize the load responses of strain gages located on various spars of a delta wing is examined. Strains measured during a laboratory load calibration of a wing structure are compared with calculations obtained from a simplified structural analysis model. Calculated and measured influence coefficient plots that show the shear, bending, and torsion characteristics of typical strain gage bridges are presented. Typical influence coefficient plots are shown for several load equations to illustrate the derivation of the equations from the component strain gage bridges. A relatively simple structural model was found to be effective in predicting the general nature of strain distributions and influence coefficient plots. The analytical processes are shown to be an aid in obtaining a good load calibration. The analytical processes cannot, however, be used in lieu of an actual load calibration of an aircraft wing.

Jenkins, J. M.↗

Resizing procedure for structures under combined mechanical and thermal loading

The fully-stressed design (FSD) appears to be the most widely used approach for sizing of flight structures under strength and minimum-gage constraints. Almost all of the experience with FSD has been with structures primarily under mechanical loading as opposed to thermal loading. In this method the structural sizes are iterated with the step size, depending on the ratio of the total stress to the allowable stress. In this paper, the thermal fully-stressed design (TFSD) procedure developed for problems involving substantial thermal stress is extended to biaxial stress members using a Von Mises failure criterion. The TFSD resizing procedure for uniaxial stress is restated and the new procedure for biaxial stress members is developed. Results are presented for an application of the two procedures to size a simplified wing structure.

Adelman, H. M.↗

Prolongation structures of nonlinear evolution equations. II

The prolongation structure of a closed ideal of exterior differential forms is further discussed, and its use illustrated by application to an ideal (in six dimensions) representing the cubically nonlinear Schroedinger equation. The prolongation structure in this case is explicitly given, and recurrence relations derived which support the conjecture that the structure is open - i.e., does not terminate as a set of structure relations of a finite-dimensional Lie group. We introduce the use of multiple pseudopotentials to generate multiple Baecklund transformation, and derive the double Baecklund transformation. This symmetric transformation concisely expresses the (usually conjectured) theorem of permutability, which must consequently apply to all solutions irrespective of asymptotic constraints.

Estabrook, F. B.↗

Free vibration analysis of spinning flexible space structures

Efficient computation of natural frequencies and associated free vibration modes of spinning flexible structures is required to accurately determine the nature of interaction between the flexible structure and the attitude control system, which is vital in relating control torques to attitude angles. While structural discretization is effected by the finite element method, the resulting eigenvalue problem is solved by a combined Sturm sequence and inverse iteration procedure that yields a few specified roots and associated vectors. An eigenvalue procedure, based on a simultaneous iteration technique, provides efficient computation of the first few roots and vectors; a modal synthesis procedure proves to be useful for eigenproblem solutions of unusual structures such as spacecraft.

Gupta, K. K.↗

Finite-element methodology for thermal analysis of convectively cooled structures

A finite-element method for steady-state thermal analysis of convectively cooled structures is presented. The method is based on representing the coolant passages by finite elements with fluid bulk temperature nodes and fluid/structure interface modes. Four finite elements are described: two basic elements (mass transport and surface convection) and two integrated elements for applications to discrete tube and plate-fin convectively cooled structural configurations. Comparative finite-element and lumped-parameter thermal analyses of several convectively cooled structures demonstrate the practicality of utilizing finite-element methodology for thermal analysis of realistic convectively cooled structures.

Source record↗

On the role of minicomputers in structural design

Results are presented of exploratory studies on the use of a minicomputer in conjunction with large-scale computers to perform structural design tasks, including data and program management, use of interactive graphics, and computations for structural analysis and design. An assessment is made of minicomputer use for the structural model definition and checking and for interpreting results. Included are results of computational experiments demonstrating the advantages of using both a minicomputer and a large computer to solve a large aircraft structural design problem.

Storaasli, O. O.↗

An optimality criterion for sizing members of heated structures with temperature constraints

A thermal optimality criterion is presented for sizing members of heated structures with multiple temperature constraints. The optimality criterion is similar to an existing optimality criterion for design of mechanically loaded structures with displacement constraints. Effectiveness of the thermal optimality criterion is assessed by applying it to one- and two-dimensional thermal problems where temperatures can be controlled by varying the material distribution in the structure. Results obtained from the optimality criterion agree within 2 percent with results from a closed-form solution and with results from a mathematical programming technique. The thermal optimality criterion augments existing optimality criteria for strength and stiffness related constraints and offers the possibility of extension of optimality techniques to sizing structures with combined thermal and mechanical loading.

Rao, G. V.↗

Honeycomb-laminate composite structure

A honeycomb-laminate composite structure was comprised of: (1) a cellular core of a polyquinoxaline foam in a honeycomb structure, and (2) a layer of a noncombustible fibrous material impregnated with a polyimide resin laminated on the cellular core. A process for producing the honeycomb-laminate composite structure and articles containing the honeycomb-laminate composite structure is described.

Gilwee, W. J., Jr.↗

Study of advanced composite structural design concepts for an arrow wing supersonic cruise configuration

Based on estimated graphite and boron fiber properties, allowable stresses and strains were established for advanced composite materials. Stiffened panel and conventional sandwich panel concepts were designed and analyzed, using graphite/polyimide and boron/polyimide materials. The conventional sandwich panel was elected as the structural concept for the modified wing structure. Upper and lower surface panels of the arrow wing structure were then redesigned, using high strength graphite/polyimide sandwich panels, retaining the titanium spars and ribs from the prior study. The ATLAS integrated analysis and design system was used for stress analysis and automated resizing of surface panels. Flutter analysis of the hybrid structure showed a significant decrease in flutter speed relative to the titanium wing design. The flutter speed was increased to that of the titanium design by selective increase in laminate thickness and by using graphite fibers with properties intermediate between high strength and high modulus values.

Turner, M. J.↗

Development of advanced composite structures

Composite structure programs: the L-1011 Advanced Composite Vertical Fin (ACVF), the L-1011 Advanced Composite Aileron, and a wing study program were reviewed. These programs were structured to provide the technology and confidence for the use of advanced composite materials for primary and secondary structures of future transport aircraft. The current status of the programs is discussed. The results of coupon tests for both material systems are presented as well as the ACVF environmental (moisture and temperature) requirements. The effect of moisture and temperature on the mechanical properties of advanced composite materials is shown. The requirements set forth in the FAA Certification Guidelines for Civil Composite Aircraft Structures are discussed as they relate to the ACVF.

Stauffer, W. A.↗

Transition from glass to graphite in manufacture of composite aircraft structure

The transition from fiberglass reinforced plastic composites to graphite reinforced plastic composites is described. Structural fiberglass design and manufacturing background are summarized. How this experience provides a technology base for moving into graphite composite secondary structure and then to composite primary structure is considered. The technical requirements that must be fulfilled in the transition from glass to graphite composite structure are also included.

Buffum, H. E.↗

Model verification of large structural systems

A computer program for the application of parameter identification on the structural dynamic models of space shuttle and other large models with hundreds of degrees of freedom is described. Finite element, dynamic, analytic, and modal models are used to represent the structural system. The interface with math models is such that output from any structural analysis program applied to any structural configuration can be used directly. Processed data from either sine-sweep tests or resonant dwell tests are directly usable. The program uses measured modal data to condition the prior analystic model so as to improve the frequency match between model and test. A Bayesian estimator generates an improved analytical model and a linear estimator is used in an iterative fashion on highly nonlinear equations. Mass and stiffness scaling parameters are generated for an improved finite element model, and the optimum set of parameters is obtained in one step.

Lee, L. T.↗

A Rayleigh-Ritz approach to the synthesis of large gyroscopic structures

The equations of motion for large structures with rotating flexible components are derived by regarding the structure as an assemblage of substructures. Based on a stationarity principle for rotating structures, it is shown that each continuous or discrete substructure can be simulated by a suitable set of admissible functions or admissible vectors. This substructure synthesis approach provides a rational basis for truncating the number of degrees of freedom both of each substructure and of the assembled structure.

Meirovitch, L.↗

A near term space demonstration program for large structures

For applications involving an employment of ultralarge structures in space, it would be necessary to have some form of space fabrication and assembly in connection with launch vehicle payload and volume limitations. The findings of a recently completed NASA sponsored study related to an orbital construction demonstration are reported. It is shown how a relatively small construction facility which is assembled in three shuttle flights can substantially advance space construction know-how and provide the nation with a permanent shuttle tended facility that can further advance large structures technologies and provide a construction capability for deployment of large structural systems envisioned for the late 1980s. The large structures applications identified are related to communications, navigation, earth observation, energy systems, radio astronomy, illumination, space colonization, and space construction.

Nathan, C. A.↗

Space Spider - A concept for fabrication of large structures

The Space Spider concept for the automated fabrication of large space structures involves a specialized machine which roll-forms thin gauge material such as aluminum and develops continuous spiral structures with radial struts to sizes of 600-1,000 feet in diameter by 15 feet deep. This concept allows the machine and raw material to be integrated using the Orbiter capabilities, then boosting the rigid system to geosynchronous equatorial orbit (GEO) without high sensitivity to acceleration forces. As a teleoperator controlled device having repetitive operations, the fabrication process can be monitored and verified from a ground-based station without astronaut involvement in GEO. The resultant structure will be useful as an intermediate size platform or as a structural element to be used with other elements such as the space-fabricated beams or composite nested tubes.

Britton, W. R.↗

Theory of the control of structures by low authority controllers

The novel idea presented is based on the observation that if a structure is controlled by distributed systems of sensors and actuators with limited authority, i.e., if the controller is allowed to modify only moderately the natural modes and frequencies of the structure, then it should be possible to apply root perturbation techniques to predict analytically the behavior of the total system. Attention is given to the root perturbation formula first derived by Jacobi for infinitesimal perturbations which neglect the induced eigenvector perturbation, a more general form of Jacobi's formula, first-order structural equations and modal state vectors, state-space equations for damper-augmented structures, and modal damping prediction formulas.

Aubrun, J. N.↗

Structural analysis consultation using artificial intelligence

The primary goal of consultation is definition of the best strategy to deal with a structural engineering analysis objective. The knowledge base to meet the need is designed to identify the type of numerical analysis, the needed modeling detail, and specific analysis data required. Decisions are constructed on the basis of the data in the knowledge base - material behavior, relations between geometry and structural behavior, measures of the importance of time and temperature changes - and user supplied specifics characteristics of the spectrum of analysis types, the relation between accuracy and model detail on the structure, its mechanical loadings, and its temperature states. Existing software demonstrated the feasibility of the approach, encompassing the 36 analysis classes spanning nonlinear, temperature affected, incremental analyses which track the behavior of structural systems.

Melosh, R. J.↗

Correlation of predicted and measured thermal stresses on a truss-type aircraft structure

A test structure representing a portion of a hypersonic vehicle was instrumented with strain gages and thermocouples. This test structure was then subjected to laboratory heating representative of supersonic and hypersonic flight conditions. A finite element computer model of this structure was developed using several types of elements with the NASA structural analysis (NASTRAN) computer program. Temperature inputs from the test were used to generate predicted model thermal stresses and these were correlated with the test measurements.

Jenkins, J. M.↗