Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Scanning Electron Microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Ru nucleation and thin film smoothness improvement with ammonia during chemical vapor deposition

This study reports the use of ammonia to inhibit the growth of previously nucleated ruthenium islands and force the nucleation of additional islands such that thinner films form as the islands coalesce with continued growth. Ruthenium films are grown at 448 K in a chemical vapor deposition process on SiO{sub 2}/Si(001) using triruthenium dodecacarbonyl, Ru{sub 3}(CO){sub 12}, with and without a constant partial pressure of ammonia. Film growth was performed at a Ru{sub 3}(CO){sub 12}/Ar pressure of 47.2 mTorr. The ammonia partial pressure varied from 0 to 27.8 mTorr. X-ray photoelectron spectroscopy was used to analyze the samples in situ. Ex situ characterization included scanning electron microscopy, atomic force microscopy, and x-ray diffraction and x-ray reflectivity. Nucleation studies limited to the first 10 min of growth revealed the maximum nanoparticle (island) density of 8.1 × 10{sup 11 }cm{sup −2} occurred at an intermediate ammonia pressure (5.25 mTorr) compared to a density of 3.1 × 10{sup 11 }cm{sup −2} for no ammonia addition. Extending film growth to 120 min and varying the ammonia partial pressure during the first 10 min followed by 5.25 mTorr ammonia pressure for the final 110 min reveals the importance of nucleation on film smoothness. A model describing the inhibition effects of ammonia during nucleation and growth is presented.

36 MATERIALS SCIENCE↗

Corrosion Behavior of Annealed Steels with Different Carbon Contents (0.002, 0.17, 0.43 and 0.7% C) in Freely Aerated 3.5% NaCl Solution

Four annealed carbon steels with different carbon contents (0.002, 0.17, 0.43, and 0.7% C), consisting of ferrite, ferrite-pearlite and fully pearlite microstructures, were selected to understand the corrosion behavior of carbon steel as a function of carbon content in freely aerated 3.5% NaCl solution. Dynamic polarization, electrochemical impedance and linear polarization methods were used. The corrosion rate obtained from the different carbon steels was found to increase greatly from ultra-low carbon steel (0.002%) to low carbon steel (0.17%) due to the presence of pearlite in the low carbon steel. However, the increase in corrosion rate was marginal with the increase in carbon content from low carbon (0.17%) to medium (0.43% C) and high carbon steels (0.7% C). The mirostrucural evolution of the steels before and after polarization test without etching as observed by scanning electron microscopy could show that the corrosion behavior of the steels with the presence of pearlite was due to the combined effect from % pearlite, interlamellar spacing and cementite/ferrite area ratio in pearlite. Pearlite morphology also led to the differential corrosion within the pearlite colony in all the steels except the steel with 0.002% C. Catalytic activity of cementite on enhancing oxygen reduction reaction attributes to the higher corrosion rates in case of the steels with the presence of pearlite.

36 MATERIALS SCIENCE↗

EBSD analysis of magnesium addition on inclusion formation in SS400 structural steel

In this study, the effect of magnesium addition on the inclusion formation in SS400 steel was investigated. The experimental specimens with and without Mg addition treatment were compared. The microstructure was observed using optical microscopy after etching with 3% nital. The morphology and chemical composition of the inclusions were analyzed via scanning electron microscopy and energy dispersive spectrometry. The lattice structure and orientation of the inclusions were identified by electron backscattering diffraction. The average size of inclusions in SS400 was between 0.67 and 0.75 μm, and between 0.65 and 0.68 μm in SS400 + Mg. The 2 ppm Mg addition resulted in the oxide formation change from Al{sub 2}O{sub 3} to MgO·Al{sub 2}O{sub 3} and in the inclusion formation change from Al{sub 2}O{sub 3}–MnS to MgO·Al{sub 2}O{sub 3}–MnS. Moreover, a simple-phase MnS with an average grain size of 1 μm to 2 μm was observed in rod-like, globular, and polyhedron forms. - Highlights: • The effect of magnesium addition was investigated for SS400 steel. • 2 ppm Mg addition changes the inclusion formation from Al2O3-MnS to MgO·Al2O3-MnS. • MnS observed in inclusions exhibits rod-like, globular, and polyhedron forms.

36 MATERIALS SCIENCE↗

Kinetics of nickel silicide growth in silicon nanowires: From linear to square root growth

The common practice for nickel silicide formation in silicon nanowires (SiNWs) relies on axial growth of silicide along the wire that is initiated from nickel reservoirs at the source and drain contacts. In the present work the silicide intrusions were studied for various parameters including wire diameter (25-50 nm), annealing time (15-120 s), annealing temperature (300-440 deg. C), and the quality of the initial Ni/Si interface. The silicide formation was investigated by high-resolution scanning electron microscopy, high-resolution transmission electron microscopy (TEM), and atomic force microscopy. The main part of the intrusion formed at 420 deg. C consists of monosilicide NiSi, as was confirmed by energy dispersive spectroscopy STEM, selected area diffraction TEM, and electrical resistance measurements of fully silicided SiNWs. The kinetics of nickel silicide axial growth in the SiNWs was analyzed in the framework of a diffusion model through constrictions. The model calculates the time dependence of the intrusion length, L, and predicts crossover from linear to square root time dependency for different wire parameters, as confirmed by the experimental data.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Study on mechanism of photocatalytic performance of La-doped TiO{sub 2}/Ti photoelectrodes by theoretical and experimental methods

TiO{sub 2} photoelectrodes with various nanostructures have been successfully prepared by the anodization method. The morphology, microstructure and optical properties of as-prepared photoelectrodes were studied by scanning electron microscopy (SEM), X-ray diffraction (XRD), ultraviolet/visible light diffuse reflectance spectra (UV/vis/DRS), surface photovoltage spectroscopy (SPS) and photocurrent. The electronic structure and optical properties of La doped/undoped TiO{sub 2} photoelectrodes with different crystal structures were calculated by the density function theory. The photocatalytic and photoelectrocatalytic activities of as-prepared photoelectrodes were evaluated. The results showed that the anodization potentials played a crucial role in the surface morphology and microstructure. Both results of theoretical calculations and experimental tests demonstrated that La-doped photoelectrodes were more sensitive to light than undoped one. The difference of photoelectrodes performance was ascribed to the crystal configuration, impurity energy levels and long-range orientation moving of photogenerated carriers. - Graphical abstract: Photophysical chemistry processes in as-prepared TiO{sub 2} photoelectrodes. Overall scheme of TiO{sub 2} photoelectrodes: (A) movement of photoelectrons and holes without bias potentials; (B) movement of photoelectrons and holes at applied bias potentials; (a) and (b) were the transmission of photogenerated electrons and holes of local enlargement of (A) (black open circle): (a) photoelectrons movement in P-TiO{sub 2} photoelectrodes and La-TiO{sub 2} photoelectrodes, the red dot line denotes the top of valence band (VB) and the bottom of conduction band (CB) of pure photoelectrodes; (b) photoelectrons movement in P-160 and La-160 TiO{sub 2} photoelectrodes (mixed crystal phase). The number refers to as follows: (1) transmission process of photoelectrons and holes; (2) recombination process of photoelectrons and holes. Arrows represent the moving direction of photoelectrons. Highlights: Black-Right-Pointing-Pointer Morphology and structure of La-doped photoelectrodes. Black-Right-Pointing-Pointer Band gap and electric structure of La-doped and undoped photoelectrodes. Black-Right-Pointing-Pointer Optical, PECH, PC and PEC properties of La-TiO{sub 2} photoelectrodes. Black-Right-Pointing-Pointer Transmission process of photoelectron-hole pairs in La-TiO{sub 2} photoelectrodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Heterometallic M/Mn (M=Cu, Co, Zn) acetate complexes as precursors for binary oxides

A facile one-pot procedure, or so-called 'direct synthesis,' was used to prepare the novel heterometallic complexes [M{sub 2}Mn(OAc){sub 6}(bpy){sub 2}], where M=Cu (1), Co (2), Zn (3), bpy=2,2'-bipyridyl, with high yields via oxidative dissolution of pure metals in a liquid phase. The complexes were characterized by an elemental analysis, single crystal X-ray diffraction method and FTIR. These complexes are proposed as precursors, whose thermal degradation may lead to the formation of solids possessing nano- to microsize levels of dispersity. The thermal behavior of the complexes obtained was studied by thermal analysis (TG/DTA/DTG) in both air and N{sub 2} and also by TPD mass-spectrometry in vacuo. The FTIR, X-ray powder diffraction (PXRD) and thermoanalytical data were used for the identification of the solid products of thermal degradation. The morphology and microstructure of the solid residues were analyzed, using scanning electron microscopy with energy dispersive X-ray microanalysis (SEM/EDX) at mkm and sub-micro levels. -- Graphical abstract: The novel heterometallic complexes [M{sub 2}Mn(OAc){sub 6}(bpy){sub 2}] (M=Cu, Co, Zn, bpy=2,2'-bipyridyl) were isolated and used as precursors for low-temperature synthesis of binary oxides. Single crystal X-ray diffraction, FTIR, TG/DTA/DTG, TPD-MS, PXRD, SEM/EDX analysis was performed on complexes and powders. Display Omitted

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Control of wetting and uniformity via ZrSi x formation in ceramic-to-metal joints fabricated using Ag-Zr brazes

The deposition of a 2.0 µm SiO 2 film on the alumina surface in Kovar TM /94% alumina joints enables the formation of a silicide reaction layer on the alumina during brazing with 97Ag2Zr1Cu. Additionally, the average and standard deviation of joint thickness decrease from 50 to 15 and 29 to 4 µm, respectively compared to joints without added SiO 2 . Finally, the average failure stress of these braze joints was 45 MPa, while that of similar joints without added SiO 2 was 90 MPa. Sessile drop experiments of 98Ag2Zr on SiO 2 and 99.6% Al 2 O 3 substrates show that the braze wets and spreads to 3x its original area on SiO 2 with a wetting angle near 0°, but remains the same area on 99.6% Al 2 O 3 with a wetting angle of 106.6°. Focused-ion-beam scanning electron microscopy analysis of a cross-section of the 98Ag2Zr sessile drop on the SiO 2 substrate has shown that Zr reacts with SiO 2 to form Zr oxide and silicide layers. Scanning transmission electron microscopy diffraction and energy dispersive X-ray spectroscopy analysis indicate this silicide layer contains tetragonal Zr 5 Si 4 . In conclusion, analysis shows the silicide layer enhances wetting and joint uniformity while unreacted SiO 2 embrittles the joint and degrades strength.

alumina↗

Combustion synthesis of silicon carbide assisted by a magnesium plus polytetrafluoroethylene mixture

In this study, the use of SiC combustion synthesis for immobilization of {sup 14}C was considered. Due to the low exothermicity of the reaction between silicon and graphite, a highly exothermic mixture (magnesium and polytetrafluoroethylene) was used both as a chemical oven and activate additive in the mixture. With this configuration the reaction between graphite and silicon was initiated and propagated on the whole sample. The self-propagating high temperature synthesis samples were characterized by using scanning electron microscopy and X-ray diffraction.

36 MATERIALS SCIENCE↗

Synthesis and characterizations of graphene oxide and reduced graphene oxide nanosheets

Interest in graphene on its excellent mechanical, electrical, thermal and optical properties, it’s very high specific surface area, and our ability to influence these properties through chemical functionalization. Chemical reduction of graphene oxide is one of the main routes of preparation for large quantities of graphenes. Hydrazine hydrate used as reducing agent to prepare for the reduced graphene oxide (RGO). There are a number of methods for generating graphene and chemically modified graphene from natural graphite flakes, graphite derivative (such as graphite oxide) and graphite interaction compounds (i.e. expandable graphite). Here we review the use of colloidal suspensions of reduced graphene oxide (RGO) with large scalable, and is adaptable to a wide variety of applications. The graphene oxide (GO) and the reduced material (RGO) were characterized by XRD, UV-Vis spectroscopy, Thermo-gravimetric analysis (TGA), Raman spectroscopy and Field emission Scanning electron microscopy (FESEM) etc.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Synthesis, characterization and electrochemical studies of nanostructured CaWO{sub 4} as platinum support for oxygen reduction reaction

Highlights: • Nanostructured CaWO{sub 4} was fabricated by co-precipitation method. • Platinum was electrodeposited onto the surface prepared nanostructured CaWO{sub 4}. • Pt/CaWO{sub 4}-graphite demonstrate good oxygen reduction reaction activity. - Abstract: In the present work, we employed nanostructured calcium tungstate as a supporting material for platinum, a well-known electrocatalyst for oxygen reduction. The co-precipitation method has been utilized to synthesize nanostructured calcium tungstate from aqueous solution. The structure and morphology of the obtained CaWO{sub 4} were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Preparation of the Pt/CaWO{sub 4}-graphite catalyst was carried out by electrodeposition of Pt onto the surface of CaWO{sub 4}/graphite electrode. The physical properties of the catalyst were determined by scanning electron microscopy analysis and energy dispersive X-ray (SEM/EDX). The electrochemical activity of the Pt/CaWO{sub 4}-graphite for the oxygen reduction reaction (ORR) was investigated in acid solution by cyclic voltammetry measurements, linear sweep voltammetry, and electrochemical impedance spectroscopy. The results revealed that the Pt/CaWO{sub 4}-graphite has higher electrocatalytic activity for oxygen reduction in comparison with Pt/graphite catalyst.

36 MATERIALS SCIENCE↗

Chemical synthesis of mesoporous CuO from a single precursor: Structural, optical and electrical properties

We report a simple method for growing photoluminescent mesoporous CuO nanoparticles by a chemical route, using the single precursor technique. The final products were characterized by powder X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), N{sub 2} adsorption-desorption isotherm, UV-vis absorption spectroscopy, photoluminescence (PL) spectroscopy, Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy and Hall measurements. Structural analysis reveals that the average pore diameter of the as-prepared CuO is about 38.8 A and it comes with an average surface area of 66.63 m{sup 2}/g. N{sub 2}-sorption analysis shows that the resulting isotherm as type IV; which is the characteristic of mesoporous materials. The average crystal diameter, as derived from the XRD data analysis is found to be about 20 nm. FESEM measurement reveals that the material is composed of cubic nanoparticles. The UV-vis spectrum of the material shows significant amount of blue-shift in the band gap energy (E{sub g}), due to the quantum confinement effect exerted by the nanocrystals. The Raman study of the CuO nanostructures also indicates the high crystalline nature of the material. From the positive sign of Hall coefficient, the p-type conduction nature of the deposited film is established. The film was found to show high magnetoresistance, which is in the order of 10{sup 5} {Omega}. - Graphical abstract: FESEM image of the mesoporous CuO prepared from Cu(OOCPh){sub 2}Lut{sub 2} complex.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Preparation and Structural Analysis of CdS Nanoparticle Embedded Polyurethane Nanocomposites

Polymer nanocomposite samples of different weight ratio of CdS were developed by solution embedding of nanoparticles in polyurethane. XRD and Scanning Electron Microscopy (SEM) were used to understand the structural properties of polymer nanocomposite samples. SEM micrograph demonstrates the dispersion of CdS nanoparticles in polymer matrix. It has been observed that crystallinity of PU decreases with increase in concentration of CdS nanoparticles. The XRD data show the characteristic peaks of nanoparticles (i.e.CdS) in nanocomposite samples, which confirm the nanostructure formation in polymer matrix.

36 MATERIALS SCIENCE↗

Optical characteristics of pulsed laser deposited Ge-Sb-Te thin films studied by spectroscopic ellipsometry

Pulsed laser deposition technique was used for the fabrication of (GeTe){sub 1-x}(Sb{sub 2}Te{sub 3}){sub x} (x = 0, 0.33, 0.50, 0.66, and 1) amorphous thin films. Scanning electron microscopy with energy-dispersive x-ray analysis, x-ray diffraction, optical reflectivity, and sheet resistance temperature dependences as well as variable angle spectroscopic ellipsometry measurements were used to characterize as-deposited (amorphous) and annealed (rocksaltlike) layers. In order to extract optical functions of the films, the Cody-Lorentz model was applied for the analysis of ellipsometric data. Fitted sets of Cody-Lorentz model parameters are discussed in relation with chemical composition and the structure of the layers. The GeTe component content was found to be responsible for the huge optical functions and thickness changes upon amorphous-to-fcc phase transition.

36 MATERIALS SCIENCE↗

Incorporation of trace elements in Portland cement clinker: Thresholds limits for Cu, Ni, Sn or Zn

This paper aims at defining precisely, the threshold limits for several trace elements (Cu, Ni, Sn or Zn) which correspond to the maximum amount that could be incorporated into a standard clinker whilst reaching the limit of solid solution of its four major phases (C{sub 3}S, C{sub 2}S, C{sub 3}A and C{sub 4}AF). These threshold limits were investigated through laboratory synthesised clinkers that were mainly studied by X-ray Diffraction and Scanning Electron Microscopy. The reference clinker was close to a typical Portland clinker (65% C{sub 3}S, 18% C{sub 2}S, 8% C{sub 3}A and 8% C{sub 4}AF). The threshold limits for Cu, Ni, Zn and Sn are quite high with respect to the current contents in clinker and were respectively equal to 0.35, 0.5, 0.7 and 1 wt.%. It appeared that beyond the defined threshold limits, trace elements had different behaviours. Ni was associated with Mg as a magnesium nickel oxide (MgNiO{sub 2}) and Sn reacted with lime to form a calcium stannate (Ca{sub 2}SnO{sub 4}). Cu changed the crystallisation process and affected therefore the formation of C{sub 3}S. Indeed a high content of Cu in clinker led to the decomposition of C{sub 3}S into C{sub 2}S and of free lime. Zn, in turn, affected the formation of C{sub 3}A. Ca{sub 6}Zn{sub 3}Al{sub 4}O{sub 15} was formed whilst a tremendous reduction of C{sub 3}A content was identified. The reactivity of cements made with the clinkers at the threshold limits was followed by calorimetry and compressive strength measurements on cement paste. The results revealed that the doped cements were at least as reactive as the reference cement.

36 MATERIALS SCIENCE↗

Single-crystalline alpha-Fe{sub 2}O{sub 3} with hierarchical structures: Controllable synthesis, formation mechanism and photocatalytic properties

A dual iron precursors system in a hydrothermal process was developed for controllable fabrication of alpha-Fe{sub 2}O{sub 3} hierarchical structures with different morphologies. Micro-pines, snowflakes and bundles were successfully synthesized simply by tuning the total concentration of the two iron precursors K{sub 4}[Fe(CN){sub 6}] and K{sub 3}[Fe(CN){sub 6}] and their molar ratio. The obtained alpha-Fe{sub 2}O{sub 3} hierarchical structures were characterized using field-emission scanning electron microscopy, transmission electron microscopy, X-ray powder diffraction, X-ray photoelectron spectroscopy and energy-dispersive X-ray analysis. The effect of experimental conditions on the morphologies of the alpha-Fe{sub 2}O{sub 3} crystals was systematically investigated. A possible formation mechanism of different alpha-Fe{sub 2}O{sub 3} hierarchical structures was proposed. Good photocatalytic properties were observed for all the hierarchical structures. - Graphical abstract: A dual iron precursors system in a hydrothermal process was developed for controllable fabrication of various alpha-Fe{sub 2}O{sub 3} hierarchical structures. Micro-pines, snowflakes and bundles were successfully fabricated by simply tuning the total concentration of the two iron precursors and their molar ratio. A possible formation mechanism of these structures was proposed.

36 MATERIALS SCIENCE↗

Characterisation of iron inclusion during the formation of calcium sulfoaluminate phase

The iron distribution among the sulfoaluminate clinker phases and its ability to enter the calcium sulfoaluminate lattice in solid solution can have a significant influence on manufacturing process and reactivity of calcium sulfoaluminate (CSA) cements. X-ray diffraction (XRD) analysis, Moessbauer spectroscopy, scanning electron microscopy (SEM) equipped with an energy dispersive X-ray analysis system (EDAX) and infrared spectroscopy were used to identify the mineralogical conditions of iron inclusion during the formation of calcium sulfoaluminate (C{sub 4}A{sub 3}S) phase from different mixtures in the CaO-Al{sub 2}O{sub 3}-Fe{sub 2}O{sub 3}-SO{sub 3} system. The mixtures, heated in a laboratory electric oven, contained stoichiometric amounts of reagent grade CaCO{sub 3}, Al{sub 2}O{sub 3}, Fe{sub 2}O{sub 3} and CaSO{sub 4.2}H{sub 2}O for the synthesis of Ca{sub 4}Al{sub (6-2x)}Fe{sub 2x}SO{sub 16}, where x, comprised between 0 and 3, is the mole number of Al{sub 2}O{sub 3} substituted by Fe{sub 2}O{sub 3}. With x increasing from 0 to 1.5, both the iron content of C{sub 4}A{sub 3}S phase and the amounts of side components such as C{sub 2}F and CS increased. For x values included in the range of 1.5-3.0, at temperatures higher than 1200 {sup o}C, melting phenomena were observed and, instead of the C{sub 4}A{sub 3}S solid solution, ferritic phases and anhydrite were formed.

36 MATERIALS SCIENCE↗

Thermal Conductivity of β-Phase Ga 2 O 3 and (Al x Ga 1– x ) 2 O 3 Heteroepitaxial Thin Films

Heteroepitaxy of β-phase gallium oxide (β-Ga 2 O 3 ) thin films on foreign substrates shows promise for the development of next-generation deep ultraviolet solar blind photodetectors and power electronic devices. In this work, the influences of the film thickness and crystallinity on the thermal conductivity of ($\bar{2}01$)-oriented β-Ga 2 O 3 heteroepitaxial thin films were investigated. Unintentionally doped β-Ga 2 O 3 thin films were grown on c-plane sapphire substrates with off-axis angles of 0° and 6° toward $\langle$$11\bar{2}0$$\rangle$ via metal–organic vapor phase epitaxy (MOVPE) and low-pressure chemical vapor deposition. The surface morphology and crystal quality of the β-Ga 2 O 3 thin films were characterized using scanning electron microscopy, X-ray diffraction, and Raman spectroscopy. The thermal conductivities of the β-Ga 2 O 3 films were measured via time-domain thermoreflectance. The interface quality was studied using scanning transmission electron microscopy. The measured thermal conductivities of the submicron-thick β-Ga 2 O 3 thin films were relatively low as compared to the intrinsic bulk value. The measured thin film thermal conductivities were compared with the Debye–Callaway model incorporating phononic parameters derived from first-principles calculations. The comparison suggests that the reduction in the thin film thermal conductivity can be partially attributed to the enhanced phonon-boundary scattering when the film thickness decreases. They were found to be a strong function of not only the layer thickness but also the film quality, resulting from growth on substrates with different offcut angles. Growth of β-Ga 2 O 3 films on 6° offcut sapphire substrates was found to result in higher crystallinity and thermal conductivity than films grown on on-axis c-plane sapphire. However, the β-Ga 2 O 3 films grown on 6° offcut sapphire exhibit a lower thermal boundary conductance at the β-Ga 2 O 3 /sapphire heterointerface. In addition, the thermal conductivity of MOVPE-grown ($\bar{2}01$)-oriented β-(Al x Ga 1–x ) 2 O 3 thin films with Al compositions ranging from 2% to 43% was characterized. Because of phonon-alloy disorder scattering, the β-(Al x Ga 1–x ) 2 O 3 films exhibit lower thermal conductivities (2.8–4.7 W/m∙K) than the β-Ga 2 O 3 thin films. The dominance of the alloy disorder scattering in β-(Al x Ga 1–x ) 2 O 3 is further evidenced by the weak temperature dependence of the thermal conductivity. This work provides fundamental insight into the physical interactions that govern phonon transport within heteroepitaxially grown β-phase Ga 2 O 3 and (Al x Ga 1–x ) 2 O 3 thin films and lays the groundwork for the thermal modeling and design of β-Ga 2 O 3 electronic and optoelectronic devices.

36 MATERIALS SCIENCE↗

Effect of biphase on dielectric properties of Bi-doped lead strontium titanate thin films

Pb{sub 0.4}Sr{sub 0.6}TiO{sub 3} (PST) thin films doped with various concentration of Bi were prepared by a sol-gel method. The phase status, surface morphology and dielectric properties of these thin films were measured by X-ray diffraction (XRD), scanning electron microscopy (SEM) and impedance analyzer, respectively. Results showed that the thin films with the maximum dielectric constant and minimum dielectric loss were obtained for x=0.15. For x<0.15, only pure PST perovskite phase were in the thin films. For 0.2<x<0.4, the PST/Bi{sub 2}Ti{sub 2}O{sub 7} biphase were obtained. The thin films with pure Bi{sub 2}Ti{sub 2}O{sub 7} pyrochlore phase were obtained for x=0.67. The biphase thin films had high tunability and high figure of merit (FOM). The FOM of PST/Bi{sub 2}Ti{sub 2}O{sub 7} biphase thin film was about 6 times higher than that thin films formed with pure perovskite phase or pure pyrochlore phase. - Graphical abstract: The Bi-doped Pb{sub 0.4}Sr{sub 0.6}TiO{sub 3} (PST) thin films prepared by the sol-gel method showed a PST/Bi{sub 2}Ti{sub 2}O{sub 7} biphase structure for 0.2<x<0.4, and had the low dielectric capacitance and dielectric loss. Display Omitted

36 MATERIALS SCIENCE↗