Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Particle shape”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Apollo 17 ropy glasses

Ropy glasses are a major soil component in the Apollo 17 gray soils 74240 and 74260. These particles form a distinct morphological type characterized by a wide range of dynamic shapes with a diagnostic sorted and welded fine-grained debris coating. Apollo 17 ropy glasses show abundant evidence for shock. Shocked lithic and mineral inclusions, lack of any igneous textures, and lechatelierite, all indicate an impact origin. A striking similarity is observed between the lunar ropy glasses and the glass impact bombs (Flaedle) of the Ries Crater in Germany. A highland basaltic composition was observed for the Apollo 17 ropy glasses in contrast to the KREEP composition of ropy glasses from the Apollo 12 and Apollo 14 landing sites. Other workers have presented convincing evidence that ejecta from Tycho reached the Taurus-Littrow Valley, and these ropy glasses may represent Tycho ejecta. However, the close stratigraphic association of the ropy glasses with the greater than 3.5 b.y. old orange glass suggests the ropy glasses may be too old to be Tycho ejecta, which should be only about 100 m.y. old. If this is the case, the ropy glasses represent impact glasses from a very old impact in an unknown highlands source area.

Fruland, R. M.↗

The effect of coronal transport of energetic solar particles

A single active center was the origin of several solar flares observed in September, 1977. The longitude of the flares ranged from approximately 115 deg E to approximately 117 deg W. During this period Helios 1, Helios 2, Voyager 1 and Voyager 2 were extended over a range of approximately 120 deg in longitude, thus providing an opportunity to study the coronal transport of energetic solar flare particles. The result of a detailed study of the relative intensity and spectral shape of approximately 2-200 MeV protons and alphas at several solar longitudes has enabled the imposition of some criteria on models of coronal transport.

Conlon, T. F.↗

The energy spectra of solar flare electrons

A survey of 50 electron energy spectra from .1 to 100 MeV originating from solar flares was made by the combination of data from two spectrometers onboard the International Sun Earth Explorer-3 spacecraft. The observed spectral shapes of flare events can be divided into two classes through the criteria of fit to an acceleration model. This standard two step acceleration model, which fits the spectral shape of the first class of flares, involves an impulsive step that accelerates particles up to 100 keV and a second step that further accelerates these particles up to 100 MeV by a single shock. This fit fails for the second class of flares that can be characterized as having excessively hard spectra above 1 MeV relative to the predictions of the model. Correlations with soft X-ray and meter radio observations imply that the acceleration of the high energy particles in the second class of flares is dominated by the impulsive phase of the flares.

Evenson, P. A.↗

Twinning of dodecanedicarboxylic acid

Twinning of 1,10-dodecanedicarboxyl acid (DDA) was observed in 0.1 mm thick films with a polarizing microscope. Twins originated from polycrystalline regions which tended to nucleate on twin faces, and terminated by intersection gone another. Twinning increased dramatically with addition of organic compounds with a similar molecular size and shape. Increasing the freezing rate, increasing the temperature gradient, and addition of silica particles increased twinning. It is proposed that twins nucleate with polycrystals and sometimes anneal out before they become observable. The impurities may enhance twinning either by lowering the twin energy or by adsorbing on growing faces.

Sen, R.↗

Effect of conductivity and concentration on the sample stream in the transverse axis of a continuous flow electrophoresis chamber

The resolution of continuous flow electrophoresis systems is generally measured by the spread of the sample bands in the direction of the electrophoretic migration. This paper evaluates the cross section of the sample bands in the plane perpendicular to the flow and shows that the spread in the direction perpendicular to the migration increased significantly with the applied electric field. Concentrated samples of monodisperse latex particles and vinyltoluene T-butylstyrene particles in sample buffers of different electrical conductivities were used to map the shape of the sample bands relative to the zero electric field case. As the electric field was applied, the sample band spread from an initial diameter of only one-third the chamber thickness until it approached the chamber walls where electroosmosis significantly reduced the resolution of separation. It can be shown, however, that it is possible to minimize these distortions by careful sample preparation and experiment design.

Miller, Teresa Y.↗

Optical Analysis of Impact Features in Aerogel From the Orbital Debris Collection Experiment on the MIR Station

The Mir Environmental Effects Package (MEEP) was deployed on the Mir station and retrieved after 18 months in space. The payload included the orbital debris collector (ODC), designed and built at the Johnson Space Center to capture and return analyzable residues of the man-made and natural particulate environment in low-Earth orbit for a detailed assessment of its compositional makeup and potential origins. The ODC exposed 2 identical trays, with highly porous, low-density SiO2 aerogel as the basic collector medium, pointed in opposite directions. The aerogel was expected to gently decelerate and capture hypervelocity particles, as opposed to other media that resulted in melting or vaporization of many impactors. Even cursory examination of the returned ODC collectors revealed a surprising variety of impact features. The compositional analyses using scanning electron "miccroscope-energy-dispersive X-ray spectroscopy concentrated on a survey-type inventory of diverse particle types and associated impact features. Detections, in the form of carrot-shaped tracks and shallow pits, included metallic Al, stainless steel, soldering compounds, human waste, and paint flakes. Many pits contained no detectable impactor residue (it was assumed to have vaporized), but most of the tracks contained analyzable residue. The study showed that aerogel would be useful for future low-velocity impact analysis.

Hoerz, Friedrich↗

High-Resolution Mapping of Lunar Crustal Magnetic Fields: Correlations with Albedo Markings of the Reiner Gamma Class

During the last eight months of the Lunar Prospector mission (December 1999-July 1999), the spacecraft was placed in a relatively low-altitude (15-30-km perapsis), near-polar orbit that allowed high-resolution mapping of crustal magnetic fields. We report here initial studies of the correlation of locally strong magnetic anomalies with unusual, swirl-like albedo markings of the Reiner Gamma class. Based on this correlation, which is known from earlier studies of Apollo subsatellite magnetometer data, it has been proposed that the swirls represent regions whose higher albedos have been preserved via deflection of the solar-wind ion bombardment by strong crustal fields. This model in turn depends on the hypothesis that solar-wind implanted H is at least one component of the process that optically matures exposed silicate surfaces in the inner solar system . Specifically, it is hypothesized that implanted H acts as an effective reducing agent to enhance the rate of production of nanophase metallic Fe particles from preexisting silicates during micrometeoroid impacts. According to the model, the curvilinear shapes of these albedo markings are caused, at least in part, by the geometry of ion deflections in a magnetic field. The improved resolution and coverage of the Prospector data allow more detailed mapping of the fields, especially on the lunar farside. This permits a more quantitative test of whether all albedo markings of this class are associated with strong local magnetic fields.Only if the latter condition is met can the solar-wind deflection hypothesis he valid. The basic procedure for mapping crustal magnetic fields using Lunar Prospector magnetometer data follows that developed for analysis of Apollo subsatellite magnetometer data. The specific mapping steps are (1) selection of mission time intervals suitable for mapping crustal fields; these are limited essentially either to times when the Moon is in a lobe of the geomagnetic tail or to times when the Moon is in the solar wind but the spacecraft is in the lunar wake; the data are transformed to a radial, east, and north coordinate system with measurements given as a function of spacecraft latitude, longitude, and altitude; (2) visual editing of individual orbit segments selected for minimal external field disturbances; (3) minimization of remaining low-frequency external fields for individual orbit data segments by quadratic detrending; and (4) two-dimensional filtering of individual orbit segments to produce a vector field map along the slightly curved surface defined by the spacecraft altitude; maps of the three field components (radial, east, and north), the field magnitude, and the spacecraft altitude are constructed. For data obtained at low to middle latitudes, the horizontal resolution of the field maps is limited by the orbit-track separation (about 30 km at the equator). Maps of the field magnitude have been constructed within limited selenographic regions based mainly on data acquired in March, April, and May of 1999. This was a time period when the orbit plane was nearly aligned with the Sun-Moon line so that field mapping was possible at times when the Moon was in the solar wind as well as when the Moon was in the geomagnetic tail. Most of the coverage is across the lunar farside. However, a shows an example of a field map produced from solar-wind wake data for a region including Reiner Gamm on western Oceanus Procellarum (location: 58.5W, 7.5N). The contour interval is 3 nT and the mean spacecraft altitude is 18 km to within the accuracy allowed by the resolution of the map (30 km or about 1 deg.); strong magnetic anomalies correlate closely with swirl locations. Individual orbit profiles (whose resolution along the orbit track is comparable to the spacecraft altitude of 18 km) also demonstrate a good correlation of field magnitude with surface albedo. In order to investigate the correlation of magnetic fields with the location of swirl features, we have reexamined available lunar imagery (Lunar Orbiter, Apollo, and Clementine) to identify and map swirl locations within regions where swirls have previously been mapped. In these images, swirls were distinguished from other high-albedo features such as crater rays by their curvilinear shapes and increased visibility in forward-scattered light. Digital maps of swirls identified by all available imagery were then superposed on maps of the field magnitude at the spacecraft altitude. Based upon analysis of these composite magnetic/geologic maps, we draw the preliminary conclusion that swirl features are associated with magnetic anomalies revealed by Lunar Prospector. Detailed maps of these swirl features are currently being constructed for the magnetically strong regions antipodal to the Imbrium, Serenitatis, and Crisium Basins. Additional information contained in the original,

Hood, L. L.↗

Microphysics and Radiative Properties of Cirrus: Instrumentation and Analysis

Work under this grant has involved further development of a new aircraft instrument (the cloudscope) for real time characterization of atmospheric particulates together with field observations of such particulates, both in the form of ice and also as nuclei responsible for nucleation of both ice and water cloud particles. Part of the work involving assessment of the frequency of ice crystal shapes has been carried out in collaboration with the Meteorological Service of Canada; part of the work in a field program with the NCAR C-130. Part of the work has been interpreted in terms of laboratory simulation of ice crystal growth under a wide variety of conditions carried out under a grant from Physical Meteorology Program, National Science Foundation.

Hallett, John↗

Radiation-induced bystander effect and adaptive response in mammalian cells

Two conflicting phenomena, bystander effect and adaptive response, are important in determining the biological responses at low doses of radiation and have the potential to impact the shape of the dose-response relationship. Using the Columbia University charged-particle microbeam and the highly sensitive AL cell mutagenic assay, we show here that non-irradiated cells acquire mutagenesis through direct contact with cells whose nuclei have been traversed with a single alpha particle each. Pretreatment of cells with a low dose of X-rays four hours before alpha particle irradiation significantly decreased this bystander mutagenic response. Results from the present study address some of the fundamental issues regarding both the actual target and radiation dose effect and can contribute to our current understanding in radiation risk assessment. c2004 COSPAR. Published by Elsevier Ltd. All rights reserved.

NASA Discipline Radiation Health↗

The Lunar Regolith

A thick layer of regolith, fragmental and unconsolidated rock material, covers the entire lunar surface. This layer is the result of the continuous impact of meteoroids large and small and the steady bombardment of charged particles from the sun and stars. The regolith is generally about 4-5 m thick in mare regions and 10-15 m in highland areas (McKay et al., 1991) and contains all sizes of material from large boulders to sub-micron dust particles. Below the regolith is a region of large blocks of material, large-scale ejecta and brecciated bedrock, often referred to as the "megaregolith". Lunar soil is a term often used interchangeably with regolith, however, soil is defined as the subcentimeter fraction of the regolith (in practice though, soil generally refers to the submillimeter fraction of the regolith). Lunar dust has been defined in many ways by different researchers, but generally refers to only the very finest fractions of the soil, less than approx.10 or 20 microns. Lunar soil can be a misleading term, as lunar "soil" bears little in common with terrestrial soils. Lunar soil contains no organic matter and is not formed through biologic or chemical means as terrestrial soils are, but strictly through mechanical comminution from meteoroids and interaction with the solar wind and other energetic particles. Lunar soils are also not exposed to the wind and water that shapes the Earth. As a consequence, in contrast to terrestrial soils, lunar soils are not sorted in any way, by size, shape, or chemistry. Finally, without wind and water to wear down the edges, lunar soil grains tend to be sharp with fresh fractured surfaces.

Noble, Sarah↗

High fidelity ground deposition measurement with robots after explosive radiological dispersion

A team of scientists from the Remote Sensing Laboratory at Joint Base Andrews, Maryland, has assembled a remote-controlled robot to field a few sodium iodide scintillators of different size and shape 18″ above ground for measurement of ground deposition of gamma-emitting particles after an explosion of a radiological dispersal device. This system uses a high-precision differential GPS device with submeter accuracy for radiation mapping. The system is most useful in characterizing large-area contamination and detecting gamma radioactivity in invisible, submicron particulate debris deposited on the ground at surface level or embedded in subsurface up to 3″ deep. The system was assembled as part of a larger effort to integrate advanced radiological detection devices into autonomous or remote-controlled robotic systems to eliminate or minimize the need for emergency responders to enter areas that pose significant health and safety risks to humans following a major radiological incident or accident. Research into autonomous algorithms is required to develop automated robotic systems for radiological survey and characterization activities in highly contaminated areas. The scope of this project also includes developing communications pathways and supporting infrastructure capabilities for different types of robotic technologies. The expected result is an advanced autonomous robotic system with integrated radiation detection electronics that allows emergency response personnel to view data remotely and in real time for radiological emergency response and consequence management purposes.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A Detailed Characterization of the Saharan Dust Collected During the Fennec Campaign in 2011: In Situ Ground-Based and Laboratory Measurements

Millions of tons of mineral dust are lifted by the wind from arid surfaces and transported around the globe every year. The physical and chemical properties of the mineral dust are needed to better constrain remote sensing observations and are of fundamental importance for the understanding of dust atmospheric processes. Ground-based in situ measurements and in situ filter collection of Saharan dust were obtained during the Fennec campaign in the central Sahara in 2011. This paper presents results of the absorption and scattering coefficients, and hence single scattering albedo (SSA), of the Saharan dust measured in real time during the last period of the campaign and subsequent laboratory analysis of the dust samples collected in two supersites, SS1 and SS2, in Algeria and in Mauritania, respectively. The samples were taken to the laboratory, where their size and aspect ratio distributions, mean chemical composition, spectral mass absorption efficiency, and spectral imaginary refractive index were obtained from the ultraviolet (UV) to the near-infrared (NIR) wavelengths. At SS1 in Algeria, the time series of the scattering coefficients during the period of the campaign show dust events exceeding 3500 Mm (exp -1), and a relatively high mean SSA of 0.995 at 670 nm was observed at this site. The laboratory results show for the fine particle size distributions (particles diameter <5μm and mode diameter at2–3 μm) in both sites a spectral dependence of the imaginary part of the refractive index Im(m) with a bow-like shape, with increased absorption in UV as well as in the shortwave infrared. The same signature was not observed, however, in the mixed particle size distribution (particle diameter<10 μm and mode diameter at 4 μm) in Algeria. Im(m) was found to range from 0.011 to 0.001i for dust collected in Algeria and 0.008 to 0.002i for dust collected in Mauritania over the wavelength range of 350-2500 nm. Differences in the mean elemental composition of the dust collected in the supersites in Algeria and in Mauritania and between fine and mixed particle size distributions were observed from EDXRF measurements, although those differences cannot be used to explain the optical properties variability between the samples. Finally, particles with low-density typically larger than 10 μm in diameter were found in some of the samples collected at the supersite in Mauritania, but these low-density particles were not observed in Algeria.

Saharan dust measured in real time↗

Accurate X-Ray Spectral Predictions: An Advanced Self-Consistent-Field Approach Inspired by Many-Body Perturbation Theory

Constrained-occupancy delta-self-consistent-field (ΔSCF) methods and many-body perturbation theories (MBPT) are two strategies for obtaining electronic excitations from first principles. Using the two distinct approaches, we study the O 1s core excitations that have become increasingly important for characterizing transition-metal oxides and understanding strong electronic correlation. The ΔSCF approach, in its current single-particle form, systematically underestimates the pre-edge intensity for chosen oxides, despite its success in weakly correlated systems. By contrast, the Bethe-Salpeter equation within MBPT predicts much better line shapes. This motivates one to reexamine the many-electron dynamics of x-ray excitations. We find that the single-particle ΔSCF approach can be rectified by explicitly calculating many-electron transition amplitudes, producing x-ray spectra in excellent agreement with experiments. This study paves the way to accurately predict x-ray near-edge spectral fingerprints for physics and materials science beyond the Bethe-Salpether equation.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Particle Acceleration and Fractional Transport in Turbulent Reconnection

We consider a large-scale environment of turbulent reconnection that is fragmented into a number of randomly distributed unstable current sheets (UCSs), and we statistically analyze the acceleration of particles within this environment. We address two important cases of acceleration mechanisms when particles interact with the UCS: (a) electric field acceleration and (b) acceleration by reflection at contracting islands. Electrons and ions are accelerated very efficiently, attaining an energy distribution of power-law shape with an index 1–2, depending on the acceleration mechanism. The transport coefficients in energy space are estimated from test-particle simulation data, and we show that the classical Fokker–Planck (FP) equation fails to reproduce the simulation results when the transport coefficients are inserted into it and it is solved numerically. The cause for this failure is that the particles perform Levy flights in energy space, while the distributions of the energy increments exhibit power-law tails. We then use the fractional transport equation (FTE) derived by Isliker et al., whose parameters and the order of the fractional derivatives are inferred from the simulation data, and solving the FTE numerically, we show that the FTE successfully reproduces the kinetic energy distribution of the test particles. We discuss in detail the analysis of the simulation data and the criteria that allow one to judge the appropriateness of either an FTE or a classical FP equation as a transport model.

79 ASTRONOMY AND ASTROPHYSICS↗

Arctic Mixed-Phase Cloud Base Ice Precipitation Properties During the M-PACE Field Campaign

Cloud-climate feedbacks are still the greatest source of uncertainty in current climate projections. Arctic clouds, which are predominantly stratiform and supercooled, often long-lived, and nearly-continuously precipitate ice particles, contribute roughly 10% of the uncertainty attributed to the global cloud feedback. This Arctic cloud uncertainty is driven by incomplete observational and theoretical knowledge required to estimate and explain the state and active processes occurring in those clouds. A focus on ice precipitation properties at Arctic cloud base rather than the surface deconfounds the product of cloud condensate sink processes from the influence of the atmospheric thermodynamic state below cloud base, rendering cloud-base properties a more appealing target for inference and evaluation of model simulations. This dataset provides a set of 25 samples from the M-PACE field campaign, all of which were retrieved using the synthesis of ARM radar and lidar measurements. The retrieved ice precipitation variables in this dataset include, among others, the ice number concentration, water content, PSD parameters, precipitation rate, mass-weighted fall velocity, vertical air motion, and effective radius, all of which are highly valuable for model evaluation and a general understanding of polar cloud sink processes. Each variable sample includes its mean value and associated uncertainty. Additional variables based on ARM measurements (liquid layer statistics, etc.) are included in this dataset as well. The retrieval algorithm and analysis of this dataset are described in Silber (JGR, 2023, https://doi.org/10.1029/2022JD038202).

54 ENVIRONMENTAL SCIENCES↗

Arctic Mixed-Phase Cloud Base Ice Precipitation Properties Over the NSA Site

Cloud-climate feedbacks are still the greatest source of uncertainty in current climate projections. Arctic clouds, which are predominantly stratiform and supercooled, often long-lived, and nearly continuously precipitate ice particles, contribute roughly 10% of the uncertainty attributed to the global cloud feedback. This arctic cloud uncertainty is driven by incomplete observational and theoretical knowledge required to estimate and explain the state and active processes occurring in those clouds. A focus on ice precipitation properties at arctic cloud base rather than the surface deconfounds the product of cloud condensate sink processes from the influence of the atmospheric thermodynamic state below cloud base, rendering cloud-base properties a more appealing target for inference and evaluation of model simulations. This data set provides more than 1800 samples of cloud-base ice precipitation properties over Utqiagvik, North Slope of Alaska, all of which were retrieved using the synthesis of ARM radar and lidar measurements. The retrieved ice precipitation variables in this data set include, among others, the ice number concentration, water content, PSD parameters, precipitation rate, mass-weighted fall velocity, vertical air motion, and effective radius, all of which are highly valuable for model evaluation and a general understanding of polar cloud sink processes. Each variable sample includes its mean value and associated uncertainty. Additional variables based on ARM measurements (liquid layer statistics, etc.) are included in this data set. The retrieval algorithm and analysis of this data set are described in Silber (JGR, 2023, https://doi.org/10.1029/2022JD038202).

54 ENVIRONMENTAL SCIENCES↗

Neutron-beam-shaping assembly for boron neutron-capture therapy

A neutron-beam-shaping assembly consisting of a moderator, a reflector, and an absorber is used to form a therapeutic neutron beam for the boron neutron-capture therapy of malignant tumors at accelerator neutron sources. A new structure of the moderator and reflector is proposed in the present article, and the results of a numerical simulation of the neutron spectrum and of the absorbed dose in a modified Snyder head phantom are presented. The application of a composite moderator and of a composite reflector and the implementation of neutron production at the proton energy of 2.3MeV are shown to permit obtaining a high-quality therapeutic neutron beam.

43 PARTICLE ACCELERATORS↗

The Ice Particle and Aggregate Simulator (IPAS). Part I: Extracting Dimensional Properties of Ice–Ice Aggregates for Microphysical Parameterization

Aggregation, the process by which two or more ice particles attach to each other, is typically observed in clouds that span a range of temperatures and is influenced by the crystal shape (habit). In this study, the resulting characteristics of ice–ice two-monomer aggregation is investigated, which is expected to improve microphysical parameterizations through more precise aggregate characteristics and in turn better predict the rate of aggregation and snow development. A systematic way to determine the aspect ratio of the aggregate was developed, which takes into account the expected falling orientations, overlap of each monomer, and any contact angle that may form through so-called constrained randomization. Distributions were used to obtain the most frequent aspect ratio, major axis, and minor axis of aggregated particles with respect to the monomer aspect ratio. Simulations were completed using the Ice Particle and Aggregate Simulator (IPAS), a model that uses predefined three-dimensional geometries, (e.g., hexagonal prisms) to simulate ice crystal aggregation and allows for variation in crystal size, shape, number, and falling orientation. In this study, after collection in a theoretical grid space, detailed information is extracted from the particles to determine the properties of aggregates. It was found that almost all monomer aspect ratios aggregate to less extreme aggregate aspect ratios at nearly the same rate. Newly formed aggregate properties are amenable to implementation into more sophisticated bulk microphysical models designed to predict and evolve particle properties, which is crucial in realistically evolving cloud ice mass distribution and for representing the collection process.

54 ENVIRONMENTAL SCIENCES↗