Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LOOPS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

M-H loop tracer based on digital signal processing for low frequency characterization of extremely thin magnetic wires

A high-sensitivity ac hysteresis loop tracer has been developed to measure the low frequency hysteresis loop of soft magnetic materials. It has been applied successfully to characterize straight pieces of amorphous glass-covered microwires with metallic nucleus down to 1.5 {mu}m thick. Based on the electromagnetic induction law, the proposed design is extremely simple and exploits the capabilities of commercially available data acquisition cards together with digital signal processing in order to achieve high-sensitivity without the need of expensive analog equipment.

36 MATERIALS SCIENCE↗

Quantifying interlayer exchange coupling via layer-resolved hysteresis loops in antiferromagnetically coupled manganite/nickelate superlattices.

In superlattices made of a half metallic ferromagnet La{sub 2/3}Ba{sub 1/3}MnO{sub 3}(LBMO) and a metallic paramagnet LaNiO{sub 3}(LNO), the field dependence of the LBMO magnetization was studied using depth- and element-sensitive x-ray resonant magnetic scattering measurements. The superlattices have ten bilayers of LBMO and LNO, and the LBMO layers were antiferromagnetically coupled across LNO spacer layers. From the x-ray measurements, the magnetic hysteresis loop of each LBMO layer was obtained, and subsequently the obtained layer-resolved LBMO hysteresis loops were utilized to determine the interlayer exchange coupling.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Runaway-loss induced negative and positive loop voltage spikes in the Aditya Tokamak

Negative spikes followed by positive ones in the loop voltage signal during the discharge are observed in the Aditya Tokamak [S. B. Bhatt et al., Indian J. Pure Appl. Phys. 27, 710 (1989)]. These spikes are always accompanied by hard x-ray bursts caused by sudden loss of runaway electrons. The observed growth of m=3 mode seemed responsible for the losses of localized beams of runaway electrons (E{sub {gamma}{approx}1}-5 MeV) from the plasma region around q=3 magnetic surface. The movement of these runaway electrons during their extraction from inside the plasma induces both positive and negative electric fields at those locations. In this paper, a one-dimensional toroidal electric field diffusion model is used to estimate the induced electric field at the plasma boundary, which matches quite well with the observed spikes in loop voltage in both magnitude as well as its temporal evolution.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hadronic Matrix Elements with Heavy Quarks: The Charm-Loop Effect in B{yields}K{sup (*)}l{sup +}l{sup -}

I present the summary of our recent work on the long-distance effect in B{yields}K{sup (*)}l{sup +}l{sup -}, generated by the four-quark operators with charmed quarks. In addition to the factorized c-barc loop, the soft-gluon emission from the loop is calculated in the framework of light-cone OPE, applying light-cone QCD sum rules. The resulting contribution of this effect to the B{yields}K{sup (*)}l{sup +}l{sup -}, decay amplitude is cast in a form of the correction to the leading Wilson coefficient C{sub 9}.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Wave propagation and noncollisional heating in neutral loop and helicon discharges

Heating mechanisms in two types of magnetized low pressure rf (13.56 MHz) discharges are investigated: a helicon discharge and a neutral loop discharge. Radial B-dot probe measurements demonstrate that the neutral loop discharge is sustained by helicon waves as well. Axial B-dot probe measurements reveal standing wave and beat patterns depending on the dc magnetic field strength and plasma density. In modes showing a strong wave damping, the plasma refractive index attains values around 100, leading to electron-wave interactions. In strongly damped modes, the radial plasma density profiles are mainly determined by power absorption of the propagating helicon wave, whereas in weakly damped modes, inductive coupling dominates. Furthermore, an azimuthal diamagnetic drift is identified. Measurements of the helicon wave phase demonstrate that initial plane wave fronts are bent during their axial propagation due to the inhomogeneous density profile. A developed analytical standing wave model including Landau damping reproduces very well the damping of the axial helicon wave field. This comparison underlines the theory whereupon Landau damping of electrons traveling along the field lines at speeds close to the helicon phase velocity is the main damping mechanism in both discharges.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Diamagnetic loop measurement in Korea Superconducting Tokamak Advanced Research machine

Diamagnetic loop (DL), which consists of two poloidal loops inside the vacuum vessel, is used to measure the diamagnetic flux during a plasma discharge in the Korea Superconducting Tokamak Advanced Research (KSTAR) machine. The vacuum fluxes in the DL signal can be compensated up to 0.1 mWb by using the coefficients, which are obtained from experimental investigations, in the vacuum flux measurements during vacuum shots under same operational conditions of magnetic coils for plasma experiment in the KSTAR machine. The maximum error in the diamagnetic flux measurement due to the errors of the coefficients was estimated as {approx}0.22 mWb. From the diamagnetic flux measurements for the ohmically heated circular plasmas in the KSTAR machine, the stored energy agrees well with the estimated kinetic energy within the discrepancy of 25%. When the electron cyclotron heating, the neutral beam injection, and the ion cyclotron resonance heating are added to the ohmically heated limiter plasmas, the additional heating effects can be clearly observed from the increase of the stored energy evaluated in the DL measurement.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

On the relevance of magnetohydrodynamic pumping in solar coronal loop simulation experiments

A magnetohydrodynamic pumping mechanism was proposed by Bellan [Phys. Plasmas 10, 1999 (2003)] to explain the formation of highly collimated plasma-filled magnetic flux tubes in certain solar coronal loop simulation experiments. In this paper, measurements on such an experiment are compared to the predictions of Bellan's pumping and collimation model. Significant discrepancies between theoretical implications and experimental observations have prompted more elaborate investigations by making use of pertinent modifications of the experimental device. On the basis of these studies, it is concluded that the proposed MHD pumping mechanism does not play a crucial role for the formation and temporal evolution of the arched plasma structures that are generated in the coronal loop simulation experiments under consideration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Classical trajectory Monte Carlo code for simulating ion beam focusing or defocusing with magnetic elements modeled as current loops or current lines

A computational tool is described that can be used for designing magnetic focusing or defocusing systems. A fully three-dimensional classical trajectory Monte Carlo simulation has been developed. Ion trajectories are simulated in the presence of magnetic elements that can be modeled as any combination of current loops and current lines. Each current loop or line may be located anywhere in the system and oriented along any of the three coordinate axes. The configuration need not be axisymmetric. The solutions are obtained using normalized parameters, which can be used for easily scaling the results. Examples are provided of the utility of the code.

43 PARTICLE ACCELERATORS↗

Dry dilution refrigerator with He-4 precool loop

He-3/He-4 dilution refrigerators (DR) are very common in sub-Kelvin temperature research. We describe a pulse tube precooled DR where a separate He-4 circuit condenses the He-3 of the dilution loop. Whereas in our previous work the dilution circuit and the He-4 circuit were separate, we show how the two circuits can be combined. Originally, the He-4 loop with a base temperature of ∼ 1 K was installed to make an additional cooling power of up to 100 mW available to cool cold amplifiers and electrical lines. In the new design, the dilution circuit is run through a heat exchanger in the vessel of the He-4 circuit so condensation of the He-3 stream of the DR is done by the He-4 stage. A much reduced condensation time (factor of 2) of the He-3/He-4 gas mixture at the beginning of an experiment is achieved. A compressor is no longer needed with the DR as the condensation pressure remains below atmospheric pressure at all times; thus the risk of losing expensive He-3 gas is small. The performance of the DR has been improved compared to previous work: The base temperature of the mixing chamber at a small He-3 flow rate is now 4.1 mK; at the highest He-3 flow rate of 1.2 mmol/s this temperature increases to 13 mK. Mixing chamber temperatures were measured with a cerium magnesium nitrate (CMN) thermometer which was calibrated with a superconducting fixed point device.

42 ENGINEERING↗

Simulations of magnetic hysteresis loops at high temperatures

The kinetic Monte-Carlo algorithm as well as standard micromagnetics are used to simulate MH loops of high anisotropy magnetic recording media at both short and long time scales over a wide range of temperatures relevant to heat-assisted magnetic recording. Microscopic parameters, common to both methods, were determined by fitting to experimental data on single-layer FePt-based media that uses the Magneto-Optic Kerr effect with a slow sweep rate of 700 Oe/s. Saturation moment, uniaxial anisotropy, and exchange constants are given an intrinsic temperature dependence based on published atomistic simulations of FePt grains with an effective Curie temperature of 680 K. Our results show good agreement between micromagnetics and kinetic Monte Carlo results over a wide range of sweep rates. Loops at the slow experimental sweep rates are found to become more square-shaped, with an increasing slope, as temperature increases from 300 K. These effects also occur at higher sweep rates, typical of recording speeds, but are much less pronounced. These results demonstrate the need for accurate determination of intrinsic thermal properties of future recording media as input to micromagnetic models as well as the sensitivity of the switching behavior of thin magnetic films to applied field sweep rates at higher temperatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Whistler wave radiation from a pulsed loop antenna located in a cylindrical duct with enhanced plasma density

Pulsed radiation from a loop antenna located in a cylindrical duct with enhanced plasma density is studied. The radiated energy and its distribution over the spatial and frequency spectra of the excited waves are derived and analyzed as functions of the antenna and duct parameters. Numerical results referring to the case where the frequency spectrum of the antenna current is concentrated in the whistler range are reported. It is shown that under ionospheric conditions, the presence of an artificial duct with enhanced density can lead to a significant increase in the energy radiated from a pulsed loop antenna compared with the case where the same source is immersed in the surrounding uniform magnetoplasma. The results obtained can be useful in planning active ionospheric experiments with pulsed electromagnetic sources operated in the presence of artificial field-aligned plasma density irregularities that are capable of guiding whistler waves.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The propagation characteristics of electromagnetic waves through plasma in the near-field region of low-frequency loop antenna

A high-speed vehicle flying through the atmosphere between 100 and 20 km may suffer from a “communication blackout.” In this paper, a low frequency system with an on-board loop antenna to receive signals is presented as a potential blackout mitigation method. Because the plasma sheath is in the near-field region of the loop antenna, the traditional scattering matrix method that is developed for the far-field region may overestimate the electromagnetic (EM) wave's attenuation. To estimate the EM wave's attenuation in the near-field region, EM interference (EMI) shielding theory is introduced. Experiments are conducted, and the results verify the EMI shielding theory's effectiveness. Simulations are also conducted with different plasma parameters, and the results obtained show that the EM wave's attenuation in the near-field region is far below than that in the far-field region. The EM wave's attenuation increases with the increase in electron density and decreases with the increase in collision frequency. The higher the frequency, the larger is the EM wave's attenuation. During the entire re-entry phase of a RAM-C module, the EM wave's attenuations are below 10 dB for EM waves with a frequency of 1 MHz and below 1 dB for EM waves with a frequency of 100 kHz. Therefore, the low frequency systems (e.g., Loran-C) may provide a way to transmit some key information to high-speed vehicles even during the communication “blackout” period.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Loop dynamics of thymidine diphosphate-rhamnose 3'-O-methyltransferase (CalS11), an enzyme in calicheamicin biosynthesis

Structure analysis and ensemble refinement of the apo-structure of thymidine diphosphate (TDP)-rhamnose 3'-O-methyltransferase reveal a gate for substrate entry and product release. TDP-rhamnose 3'-O-methyltransferase (CalS11) catalyses a 3'-O-methylation of TDP-rhamnose, an intermediate in the biosynthesis of enediyne antitumor antibiotic calicheamicin. CalS11 operates at the sugar nucleotide stage prior to glycosylation step. Here, we present the crystal structure of the apo form of CalS11 at 1.89 Å resolution. We propose that the L2 loop functions as a gate facilitating and/or providing specificity for substrate entry or promoting product release. Ensemble refinement analysis slightly improves the crystallographic refinement statistics and furthermore provides a compelling way to visualize the dynamic model of loop L2, supporting the understanding of its proposed role in catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An experimental study on the performance of closed loop pulsating heat pipe (CLPHP) with methanol as a working fluid

Thermal control is an important topic for thermal management of small electrical and electronic devices. Closed loop pulsating heat pipe (CLPHP) arises as the best solution for thermal control. The aim of this experimental study is to search a CLPHP of better thermal performance for cooling different electrical and electronic devices. In this experiment, methanol is used as working fluid. The effect of using methanol as a working fluid is studied on thermal performance in different filling ratios and angles of inclination. A copper capillary tube is used where the inner diameter is 2 mm,outer diameter is 2.5 mm and 250 mm long. The CLPHP has 8 loops where the evaporation section is 50 mm, adiabatic section is 120 mm and condensation section is 80 mm. The experiment is done using FR of 40%-70% with 10% of interval and angles of inclination 0° (vertical), 30°, 45°, 60° varying heat input. The results are compared on the basis of evaporator temperature, condenser temperature and their differences, thermal resistance, heat transfer co-efficient, power input and pulsating time. The results demonstrate the effect of methanol in different filling ratios and angles of inclination. M ethanol shows better performance at 30° inclination with 40% FR.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ferroelectric-like hysteresis loop originated from non-ferroelectric effects

Piezoresponse force microscopy (PFM) has provided advanced nanoscale understanding and analysis of ferroelectric and piezoelectric properties. In PFM-based studies, electromechanical strain induced by the converse piezoelectric effect is probed and analyzed as a PFM response. However, electromechanical strain can also arise from several non-piezoelectric origins that may lead to a misinterpretation of the observed response. Among them, electrostatic interaction can significantly affect the PFM response. Nonetheless, previous studies explored solely the influence of electrostatic interaction on the PFM response under the situation accompanied with polarization switching. Here, we show the influence of the electrostatic interaction in the absence of polarization switching by using unipolar voltage sweep. The obtained results reveal that the electromechanical neutralization between piezoresponse of polarization and electrostatic interaction plays a crucial role in the observed ferroelectric-like hysteresis loop despite the absence of polarization switching. Furthermore, our work can provide a basic guideline for the correct interpretation of the hysteresis loop in PFM-based studies.

36 MATERIALS SCIENCE↗

Guided search for desired functional responses via Bayesian optimization of generative model: Hysteresis loop shape engineering in ferroelectrics

Advances in theoretical modeling across multiple disciplines have yielded generative models capable of high veracity in predicting macroscopic functional responses of materials emerging as a result of complex non-local interactions. Correspondingly, of interest is the inverse problem of finding the model parameter that will yield desired macroscopic responses, such as stress–strain curves, ferroelectric hysteresis loops, etc. Here, we suggest and implement Gaussian process based methods that allow to effectively sample the degenerate parameter space of a complex non-local model to output regions of parameter space which yield desired functionalities. In this work, we discuss the specific adaptation of the acquisition function and sampling function to make the process efficient and balance the efficient exploration of parameter space for multiple possible minima and exploitation to densely sample the regions of interest where target behaviors are optimized. Additionally, this approach is illustrated via the hysteresis loop engineering in ferroelectric materials but can be adapted to other functionalities and generative models.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Loop SBS oscillator on a stationary nonlinear refractive index grating

A loop SBS oscillator is studied, in which pump radiation coupled out from a nonlinear medium is directed backward to the medium. To increase the interaction length, a light guide is used. The feedback is obtained on a stationary nonlinear refractive index grating produced by the pump waves. The signal generated at the Stokes frequency in the loop propagates in the direction opposite to the pump and is amplified due to the classical backward SBS. Such an oscillator can be treated as a distributed feedback oscillator produced by the pump waves themselves. (nonlinear optical phenomena)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗