Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LASER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85
All sourcesNASA NTRSDOE OSTI
DOE OSTI2011

Conversion efficiency and spectral broadening of the K-{alpha} line emitted from planar titanium targets irradiated with ultra-short laser pulses of high intensity

A study of the conversion efficiency and line shape of the K-{alpha} x-ray line radiation from a planar titanium target irradiated by an ultra-short laser pulse is performed. The conversion efficiency and spectral broadening are studied as a function of laser intensity (5 x 10{sup 16}-10{sup 18} W cm{sup -2}), laser pulse duration (45 fs-800 fs), and laser fluence (2 x 10{sup 3}-4.2 x 10{sup 4} J cm{sup -2}). The K-{alpha}{sub 1} line (4510 eV) is observed to be broadened (up to {approx}9 eV), predominantly towards the higher energy side and strongly depends on the laser fluence rather than on laser intensity. The reason for the spectral broadening is attributed to K-{alpha} emission in warm dense plasma. The role of hot electrons and direct laser heating on spectral broadening is outlined. In addition to this, our observations indicates that the presence of pre-plasma strongly contribute to the observed broadening through the inner-shell transitions in multiply charged titanium ions in the pre-plasma. The appropriate laser irradiation parameters to achieve high conversion efficiency and minimum spectral width of the K-{alpha} radiation are identified. The study is important, since the control of the spectral profile is of general interest for diffraction or scattering experiments in view of its potential in increasing temporal resolution.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Transmission Geometry Laser Ablation into a Non-Contact Liquid Vortex Capture Probe for Mass Spectrometry Imaging

RATIONALE: Capture of material from a laser ablation plume into a continuous flow stream of solvent provides the means for uninterrupted sampling, transport and ionization of collected material for coupling with mass spectral analysis. Reported here is the use of vertically aligned transmission geometry laser ablation in combination with a new non-contact liquid vortex capture probe coupled with electrospray ionization for spot sampling and chemical imaging with mass spectrometry. Methods: A vertically aligned continuous flow liquid vortex capture probe was positioned directly underneath a sample surface in a transmission geometry laser ablation (355 nm, 10 Hz, 7 ns pulse width) setup to capture into solution the ablated material. The outlet of the vortex probe was coupled to the Turbo V ion source of an AB SCIEX TripleTOF 5600+ mass spectrometer. System operation and performance metrics were tested using inked patterns and thin tissue sections. Glass slides and slides designed especially for laser capture microdissection, viz., DIRECTOR slides and PEN 1.0 (polyethylene naphthalate) membrane slides, were used as sample substrates. Results: The estimated capture efficiency of laser ablated material was 24%, which was enabled by the use of a probe with large liquid surface area (~ 2.8 mm2) and with gravity to help direct ablated material vertically down towards the probe. The swirling vortex action of the liquid surface potentially enhanced capture and dissolution of not only particulates, but also gaseous products of the laser ablation. The use of DIRECTOR slides and PEN 1.0 (polyethylene naphthalate) membrane slides as sample substrates enabled effective ablation of a wide range of sample types (basic blue 7, polypropylene glycol, insulin and cyctochrome c) without photodamage using a UV laser. Imaging resolution of about 6 m was demonstrated for stamped ink on DIRECTOR slides based on the ability to distinguish features present both in the optical and in the chemical image. This imaging resolution was 20 times better than the previous best reported results with laser ablation/liquid sample capture mass spectrometry imaging. Using thin sections of brain tissue the chemical image of a selected lipid was obtained with an estimated imaging resolution of about 50 um. Conclusions: A vertically aligned, transmission geometry laser ablation liquid vortex capture probe, electrospray ionization mass spectrometry system provides an effective means for spatially resolved spot sampling and imaging with mass spectrometry.

DIRECTOR slides↗
DOE OSTI2018

Corrosion Inhibition of Cold-rolled Low Carbon Steel with Pulse Fiber Laser Ablation in Water

This study aims at the use of a fiber laser for modifying the surface properties of cold-rolled low carbon steel via a pulse laser ablation technique in water. The effect on the corrosion behavior of the fiber laser-treated metal surface was investigated in NaCl and HCl environments. Electrochemical tests showed significant improvement in the corrosion resistance of the laser-treated sample in NaCl, with an increase in open-circuit potential (OCP) from − 0.65 to − 0.60 V and an inhibition efficiency of 89.22% as obtained from the impedance study. Such improvement was less significant in an acidic environment. Lower corrosion rates of 20.9 mpy and 5.819 × 10{sup 3} mpy were obtained for the laser-treated samples in neutral and acidic electrolytes, respectively, than the corrosion rates obtained for the as-received samples (33.2 mpy and 11.98 × 10{sup 3} mpy). Morphological analysis indicated a passive film built by spherical grains of regular size on the metal surface after laser treatment. The corrosion inhibition effects in NaCl were evident by the nonexistence of the common corrosion products of lepidocrocite and crystalline structures that were seen on as-received samples; only polyhedral crystals with micrograins grown on them were seen covering the laser-treated surface. Therefore, the laser treatment using a fiber laser source improved the corrosion resistance of cold-rolled low carbon steel.

36 MATERIALS SCIENCE↗
DOE OSTI2017

A Simple Method for Improving the Spatial Resolution in Infrared Laser Ablation Mass Spectrometry Imaging

In mass spectrometry imaging of tissues, the size of structures that can be distinguished is determined by the spatial resolution of the imaging technique. Here, the spatial resolution of IR laser ablation is markedly improved by increasing the distance between the laser and the focusing lens. As the distance between the laser and the lens is increased from 1 to 18 m, the ablation spot size decreases from 440 to 44 μm. This way, only the collimated center of the divergent laser beam is directed on the focusing lens, which results in better focusing of the beam. Part of the laser energy is lost at longer distance, but this is compensated by focusing of the radiation to a smaller area on the sample surface. The long distance can also be achieved by a set of mirrors, between which the radiation travels before it is directed to the focusing lens and the sample. This method for improving the spatial resolution can be utilized in mass spectrometry imaging of tissues by techniques that utilize IR laser ablation, such as laser ablation electrospray ionization, laser ablation atmospheric pressure photoionization, and matrix-assisted laser desorption electrospray ionization. .

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2019

Surface chemistry and composition-induced variation of laser interference-based surface treatment of Al alloys

A key limitation for the use of aluminum alloys in multi-material structural components is effective surface cleaning and texturing techniques to improve the quality of structural joints. In this study, the surface and sub-surface chemistries are investigated for a novel surface treatment method using laser interferometry produced by two beams of a pulsed Nd:YAG laser. Surfaces of AA 5128 aluminum alloy were treated using a two-beam laser interference setup, enabling the structuring of the surface at length scales much less than that of the laser beam. Periodic and patterned surface structures were created by the interference power profile through ablation of deposits and debris and melting and re-solidification of the near-surface region during laser-treatment. Chemical changes to the Al alloy surface induced by laser treatment were examined in detail in this study using both x-ray photoelectron spectroscopy (XPS) and scanning Auger microanalysis (SAM) as a function of number of interfering laser shots. XPS surface analysis indicates that this laser technique is effective at cleaning aluminum surfaces. Furthermore, SAM data indicated that there is a compositional-induced variation of Mg due to laser-interference as Mg-rich areas were found in periodic interference-structured ridges.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coupling laser physics to radiation-hydrodynamics

In order to accurately model implosion hydrodynamics in a radiation-hydrodynamics code, it is essential to include accurate accounting for energy deposition physics. In inertial confinement fusion (ICF), where capsules are driven by lasers or laser-driven x-rays, energy deposition profiles and energy transport have a strong impact on the development and evolution of capsule dynamics and hydrodynamic instabilities. Nevertheless, accurately modeling laser beam propagation in radiation-hydrodynamics codes presents unique challenges associated with disparate resolution requirements, the potential to seed spurious noise in highly unstable systems, and computational expense. We discuss a new method for coupling laser ray-tracing physics to a radiation hydrodynamics code, developed in the process of implementing the Mazinisin laser ray-trace into the xRAGE radiation hydrodynamics code. In contrast to previous approaches, in which laser ray-tracing is performed on the radiation-hydrodynamics mesh, our method involves a mesh generation and evolution strategy that addresses the unique requirements of the laser ray-trace in a separate mesh, enabling performance enhancements and strategies to reduce noise seeded by the discretization of beams into computational rays. In addition, we have employed several methods to ensure that spurious mesh imprinting is minimized. These involved optimizing the laser and radiation-hydrodynamics meshes as well as interpolation between them and requires the use of an exact initialization method for the radiation-hydrodynamics mesh. Furthermore, these techniques have enabled efficient computation of laser-driven implosions and other experiments with minimal introduction of spurious noise.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Effect of initial γ -irradiation on infrared laser ablation of poly(vinyl alcohol) studied by infrared spectroscopy

We report the effect of initial γ-irradiation of poly(vinyl alcohol) (PVA) on the kinetics of polymer ablation under CO 2 laser irradiation was studied using infra-red spectroscopy. The rate of laser ablation rapidly decreases with increasing time of laser ablation up to 10 s. Initial γ-irradiation of a dose up to 100 kGy reduces the rate of the laser ablation, just like the effect of laser exposure. The number of OH and CH groups decrease in PVA both with laser irradiation and with γ-irradiation. The number of OH groups decreases more under laser irradiation. Unsaturated bonds are formed in γ–irradiated PVA on the surface of the crater formed by laser ablation of the polymer that has undergone radiolysis. Increasing the dose of initial γ-irradiation from 100 to 2300 kGy leads to an increase in the intensity of the IR bands of the unsaturated bonds. The number of IR bands in the spectra of the laser ablation crater of PVA does not change with the dose of initial γ-irradiation. A dose of radiolysis of 3500 kGy significantly changes the IR spectra of both the ablation crater and the coating formed from the ablation products. Many bands characteristic for PVA are no longer present and the intensities of bands corresponding to unsaturated bonds are increased. A computational model for loss of water and ketone formation was developed for PVA and PVA including a diol using G3(MP2). The highest activation energy barrier step in the decomposition reaction was formation of the enol species and water was shown to catalyze all decomposition steps.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Laser lift-off scribing of the CZTSe thin-film solar cells at different pulse durations

Here, the transition to fully sized solar modules requires additional three-step laser structuring processes to preserve small-scale cell efficiencies over the large areas. The adjacent cell isolation (the P3 scribe) was found to be the most sensitive process in the case of laser induced damage. The laser induced layer lift-off mechanism seems to be a very attractive process for the P3 patterning, since almost all the laser affected material is removed by mechanical spallation. However, a laser induced layer spallation behavior together with scribe electrical validation under the different laser pulse durations was not investigated extensively in the past. Therefore, we report our novel results on the P2 and P3 laser lift-off processing of the Cu 2 ZnSn(S, Se 4 ) (CZTSe) thin-film solar cells covering the pulse duration range from 300 fs to 60 ps. Shorter sub-ps pulses enabled us to process smaller P2 and P3 craters, although the lift-off threshold fluences were higher compared to the longer ps pulses. In the case of the layer lift-off, the laser radiation had to penetrate through the layer stack down to the CZTSe/Mo interface. At shorter sub-ps pulses, the nonlinear effects triggered absorption of the laser radiation in the bulk of the material, resulting in increased damage of the CZTSe layer. The Raman measurements confirmed the CZTSe surface stoichiometry changes for shorter pulses. Furthermore, shorter pulses induced higher electrical conductivity of a scribe, resulting in lower photo-electrical efficiency during the mini-module simulation. In the case of the P3 lift-off scribing, the 10 ps pulses were more favorable than shorter femtosecond pulses.

14 SOLAR ENERGY↗
DOE OSTI2017

Laser ablation of sub-10 nm silver nanoparticles

Laser ablation of silver nanoparticles (NPs) was studied with laser post-ionization (LPI) time-of-flight mass spectrometry (TOF MS). Silver NPs containing ~15 000 Ag atoms (4 nm radius) were deposited by soft landing (energy 3 eV/atom) onto indium tin oxide (ITO)/glass substrates. Laser ablation was performed using frequency-doubled Ti:sapphire nanosecond pulsed laser irradiation at three different wavelengths (371, 401, and 421 nm), whereas for post-ionization, pulses from an F 2 laser were used. Laser fluences and time delay dependencies of Ag and In signals were obtained. Using these data, the temperature of the desorption source as well as its time duration were calculated. It was found that the peak temperature of NPs was above their melting point and they cooled down slowly, with temperature decay time of several hundreds of nanoseconds. This anomalous behavior was explained based on a model where the semiconducting ITO substrate is initially transparent to the desorption laser radiation but starts to adsorb it due to the temperature increase arising from heat exchange with NPs. Poor heat conduction in the ITO film creates conditions for long-lived hot spots on the surface and initiates further optical damage of the substrate. No difference in the ablation process due to plasmon resonance was detected, likely due to thermal expansion and melting of NPs during laser irradiation, which then broadens the plasmon absorption band enough to cover all wavelengths used. Here, these results clearly demonstrate that the process of NP interaction with laser radiation is governed not only by initial optical and thermophysical parameters of NPs and the surrounding media, but also by their alteration due to temperature increases during the irradiation process.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Vacuum laser acceleration of super-ponderomotive electrons using relativistic transparency injection

Abstract Intense lasers can accelerate electrons to very high energy over a short distance. Such compact accelerators have several potential applications including fast ignition, high energy physics, and radiography. Among the various schemes of laser-based electron acceleration, vacuum laser acceleration has the merits of super-high acceleration gradient and great simplicity. Yet its realization has been difficult because injecting free electrons into the fast-oscillating laser field is not trivial. Here we demonstrate free-electron injection and subsequent vacuum laser acceleration of electrons up to 20 MeV using the relativistic transparency effect. When a high-contrast intense laser drives a thin solid foil, electrons from the dense opaque plasma are first accelerated to near-light speed by the standing laser wave in front of the solid foil and subsequently injected into the transmitted laser field as the opaque plasma becomes relativistically transparent. It is possible to further optimize the electron injection/acceleration by manipulating the laser polarization, incident angle, and temporal pulse shaping. Our result also sheds light on the fundamental relativistic transparency process, crucial for producing secondary particle and light sources.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2011

Reflection of femtosecond laser light in multipulse ablation of metals

The shot-to-shot reflectance of high-intensity laser light is studied as a function of both the number of laser shots and laser fluence in multipulse ablation of a metal when the irradiated surface undergoes structural changes from an initially smooth surface to a deep crater. Our study shows that the reflectance of the irradiated surface significantly decreases due to the high intensity of laser pulses and the laser-induced surface structures in ablation regimes typically used for femtosecond laser processing of materials. The high-intensity effect dominates in the reflection reduction at low numbers of laser shots when laser-induced surface structures do not cause the reflectance to decrease noticeably. With increasing the number of laser shots, the structural effect comes into play, and both high-intensity and structural effects quickly reduce the reflectance of the sample to a low value.

36 MATERIALS SCIENCE↗
DOE OSTI2012

Molecular dynamic studies on anisotropic explosion of laser irradiated Xe cluster

A three dimensional molecular dynamic model is used to investigate the dynamics of Xe clusters of various radii irradiated by laser of moderate intensities ({approx}10{sup 14}-10{sup 16}W/cm{sup 2}). The FWHM pulse duration of the laser is varied from few laser cycles to hundreds of femtosecond. For cluster of radius 50 A irradiated by a laser of 170 fs pulse duration, it is observed that ion yield is more along the direction of laser polarization than perpendicular to it. This trend reverses (more ions are emitted along the direction perpendicular to laser polarization than parallel to it) when laser pulses of few cycles are used. This reversal of anisotropy is explained on the basis of spatial shielding of ions due to the oscillating inner electron cloud along direction of laser electric field. The nature of anisotropy remains same with variations in laser intensity and cluster size.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2013

Enhanced photocatalytic efficiency in zirconia buffered n-NiO/p-NiO single crystalline heterostructures by nanosecond laser treatment

We report the formation of NiO based single crystalline p-n junctions with enhanced photocatalytic activity induced by pulsed laser irradiation. The NiO epilayers were grown on Si(001) substrates buffered with cubic yttria-stabilized zirconia (c-YSZ) by using pulsed laser deposition. The NiO/c-YSZ/Si heterostructures were subsequently laser treated by 5 pulses of KrF excimer laser (pulse duration = 25 Multiplication-Sign 10{sup -9} s) at lower energies. Microstructural studies, conducted by X-ray diffraction ({theta}-2{theta} and {phi} techniques) and high resolution transmission electron microscope, showed a cube-on-cube epitaxial relationship at the c-YSZ/Si interface; the epitaxial relationship across the NiO/c-YSZ interface was established as NiO<111 > Double-Vertical-Line Double-Vertical-Line c-YSZ<001> and in-plane NiO<110> Double-Vertical-Line Double-Vertical-Line c-YSZ<100>. Electron microscopy studies showed that the interface between the laser annealed and the pristine region as well as the NiO/c-YSZ interface was atomically sharp and crystallographically continuous. The formation of point defects, namely oxygen vacancies and NiO, due to the coupling of the laser photons with the NiO epilayers was confirmed by XPS. The p-type electrical characteristics of the pristine NiO epilayers turned to an n-type behavior and the electrical conductivity was increased by one order of magnitude after laser treatment. Photocatalytic activity of the pristine (p-NiO/c-YSZ/Si) and the laser-annealed (n-NiO/p-NiO/c-YSZ/Si) heterostructures were assessed by measuring the decomposition rate of 4-chlorophenol under UV light. The photocatalytic reaction rate constants were determined to be 0.0059 and 0.0092 min{sup -1} for the as-deposited and the laser-treated samples, respectively. The enhanced photocatalytic efficiency was attributed to the suppressed charge carrier recombination in the NiO based p-n junctions and higher electrical conductivity. Besides, the oxygen vacancies ease the adsorption of 4-chlorophenol, hydroxyl, and water molecules to the surface. Thus, n-NiO/p-NiO single crystalline catalysts can be introduced as a potent candidate to remediate the environmental pollution.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2014

Catastrophic nanosecond laser induced damage in the bulk of potassium titanyl phosphate crystals

Due to its high effective nonlinearity and the possibility to produce periodically poled crystals, potassium titanyl phosphate (KTiOPO{sub 4}, KTP) is still one of the economically important nonlinear optical materials. In this overview article, we present a large study on catastrophic nanosecond laser induced damage in this material and the very similar RbTiOPO{sub 4} (RTP). Several different systematic studies are included: multiple pulse laser damage, multi-wavelength laser damage in KTP, damage resistance anisotropy, and variations of the laser damage thresholds for RTP crystals of different qualities. All measurements were carried out in comparable experimental conditions using a 1064 nm Q-switched laser and some were repeated at 532 nm. After summarizing the experimental results, we detail the proposed model for laser damage in this material and discuss the experimental results in this context. According to the model, nanosecond laser damage is caused by light-induced generation of transient laser-damage precursors which subsequently provide free electrons that are heated by the same nanosecond pulse. We also present a stimulated Raman scattering measurement and confront slightly different models to the experimental data. Finally, the physical nature of the transient damage precursors is discussed and similarities and differences to laser damage in other crystals are pointed out.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2014

Laser stimulation can activate autophagy in HeLa cells

For decades, lasers have been a daily tool in most biological research for fluorescent excitation by confocal or multiphoton microscopy. More than 20 years ago, cell photodamage caused by intense laser stimulation was noticed by generating reactive oxygen species, which was then thought as the main damage effect by photons. In this study, we show that laser stimulation can induce autophagy, an important cell lysosomal pathway responding to immune stimulation and starvation, without any biochemical treatment. Two different types of laser stimulations are found to be capable of activating autophagy: continuous scanning by continuous-wave visible lasers and a short-time flash of femtosecond laser irradiation. The autophagy generation is independent from wavelength, power, and scanning duration of the visible lasers. In contrast, the power of femtosecond laser is very critical to autophagy because the multiphoton excited Ca{sup 2+} dominates autophagy signaling. In general, we show here the different mechanisms of autophagy generation by such laser stimulation, which correspond to confocal microscopy and cell surgery, respectively. Those results can help further understanding of photodamage and autophagy signaling.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Use of the Hugoniot Elastic Limit in Laser Shockwave Experiments to Relate Velocity Measurements

---The Idaho National Laboratory (INL) has been developing a Laser Shock system to characterize interface strength in plate fuel for research reactors around the world [1]. This work is in support of the Unites states High Performance Research Reactor program whose goal is to reduce the risk of proliferation of weapons grade fuel while maintaining reactor performance. The INL has been working with National Research Council Canada (NRC) on this project for the last five years. ---One of the concerns of the project is the difficulty of calibrating and standardizing the laser shock technique. The generation of the stress wave by the laser impinging on the plate surface is complex, with amplitude and shape dependence on numerous factors relating to the temporal and spatial distribution of power in the laser spot, surface treatment, and material properties of the plate. Thus the resulting back-face surface velocity, which is used to measure the time-varying stress field within the plate, is difficult to reproduce across different measurement systems. A technique that can generate or indicate a known shock intensity independent of the generating conditions would be valuable and allow us to directly compare results from different systems. ---A Laser Shock round robin test between the system at NRC and the INL was conducted. The goal of the round robin was to determine if there was any bias between the two systems. During the analysis of the data, it was noted that the Hugoniot Elastic Limit (HEL) was consistent within both system data sets independent of the laser power used. An analytical study under development supports that the HEL in metals could be a robust and simple benchmark to compare stresses generated by different laser shock systems. The HEL is a material property that should be insensitive to differences in the shock laser and surface preparation which enhances the reliability of the resulting HEL velocity measurement. 1. J. M. Lacy, J. A. Smith and B. H. Rabin, "Developing a Laser Shockwave Model for Characterizing Diffusion Bonded Interfaces," The 41st Annual Review of Progress in Quantitative Nondestructive Evaluation," Boise, ID, U.S.A., July 2014.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Accuracy of the time-averaged ponderomotive approximation for laser-plasma accelerator modeling

Reliable modeling of laser-plasma accelerators, where a short and intense laser pulse propagates in an underdense plasma over long distances, is a computationally challenging task. This is due to the great disparity among the scales involved in the modeling, ranging from the micrometer scale of the laser wavelength to, for instance, the meter scale of the laser-plasma interaction length for a multi-GeV-class laser-plasma accelerator. To reduce such imbalance, the time-averaged ponderomotive approximation may be used, where the plasma particle dynamics is analytically averaged over the laser frequency, and only spatiotemporal scales associated with the laser envelope are retained in the calculations, resulting in significant computational savings. Here, we characterize the accuracy and robustness of the time-averaged ponderomotive approximation for a range of laser parameters of interest for present and future laser-plasma accelerators, and we show that the error introduced by the averaging process is small in all relevant cases.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Electron energy gain due to a laser frequency modulation experienced by electron during betatron motion

Direct laser acceleration of electrons is an important energy deposition mechanism for laser-irradiated plasmas that is particularly effective at relativistic laser intensities in the presence of quasi-static laser-driven plasma electric and magnetic fields. These radial electric and azimuthal magnetic fields provide transverse electron confinement by inducing betatron oscillations of forward-moving electrons undergoing laser acceleration. Electrons are said to experience a betatron resonance when the frequency of betatron oscillations matches the average frequency of the laser field oscillations at the electron position. In this paper, we show that the modulation of the laser frequency as seen by an electron performing betatron oscillations can be another important mechanism for net energy gain that is qualitatively different from the betatron resonance. Specifically, we show that the frequency modulation experienced by the electron can lead to net energy gain in the regime where the laser field performs three oscillations per betatron oscillation. There is no net energy gain in this regime without the modulation because the energy gain is fully compensated by the energy loss. The modulation slows down the laser oscillation near transverse stopping points, increasing the time interval during which the electron gains energy and making it possible to achieve net energy gain.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗