Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLAME”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Effects of repetitive pulsing on multi-kHz planar laser-induced incandescence imaging in laminar and turbulent flames

Planar laser-induced incandescence (LII) imaging is reported at repetition rates up to 100 kHz using a burst-mode laser system to enable studies of soot formation dynamics in highly turbulent flames. Furthermore, to quantify the accuracy and uncertainty of relative soot volume fraction measurements, the temporal evolution of the LII field in laminar and turbulent flames is examined at various laser operating conditions. Under high-speed repetitive probing, it is found that LII signals are sensitive to changes in soot physical characteristics when operating at high laser fluences within the soot vaporization regime. For these laser conditions, strong planar LII signals are observed at measurement rates up to 100 kHz but are primarily useful for qualitative tracking of soot structure dynamics. However, LII signals collected at lower fluences allow sequential planar measurements of the relative soot volume fraction with a sufficient signal-to-noise ratio at repetition rates of 10–50 kHz. Finally, guidelines for identifying and avoiding the onset of repetitive probe effects in the LII signals are discussed, along with other potential sources of measurement error and uncertainty.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Development of Criteria for Flashback Propensity in Jet Flames for High Hydrogen Content and Natural Gas Type Fuels

Due to increasingly stringent air quality requirements stationary power gas turbines have moved to lean-premixed operation, which reduces pollutant emissions but can result in flashback. Curtailing flashback can be difficult with hydrocarbon fuels and becomes even more challenging when hydrogen is used as the fuel. In fact, flashback is a key operability issue associated with low emission combustion of high hydrogen content fuels. Flashback can cause serious damage to the premixer hardware. Hence, design tools to predict flashback propensity are of interest. Such a design tool has been developed based on the data gathered by experimental study to predict boundary layer flashback using non-dimensional parameters. The flashback propensity of a premixed jet flame has been studied experimentally. Boundary layer flashback has been investigated under turbulent flow conditions at elevated pressures and temperatures (i.e. 3 atm to 8 atm and 300 K to 500 K). The data presented in this study are for hydrogen fuel at various Reynolds numbers, which are representative of practical gas turbine premixer conditions and are significantly higher than results currently available in the literature. Three burner heads constructed of different materials (stainless steel, copper, and zirconia ceramic) were used to evaluate the effect of tip temperature, a parameter found previously to be an important factor in triggering flashback. This study characterizes flashback systematically by developing a comprehensive non-dimensional model which takes into account all effective parameters in boundary layer flashback propensity. The model was optimized for new data and captures the behavior of the new results well. Further, comparison of the model with the single existing study of high pressure jet flame flashback also indicates good agreement. The model developed using the high pressure test rig is able to predict flashback tendencies for a commercial gas turbine engine and can thus serve as a design tool for identifying when flashback is likely to occur for a given geometry and condition.

03 NATURAL GAS↗

A Flame Spray Process for Cathode Materials Manufacturing for Lithium Ion Batteries

Flame (combustion) processes are the most economic ones to produce fine powders and have been used to produce pigment titanium oxide and fused silica in large volumes. In this work a flame spray pyrolysis (FSP) process has been developed to make metal oxide powders for the positive electrode materials at low cost. In particular, the work was focused on making metal oxides of NMC materials with stoichiometric compositions and desired morphologies. Our FSP is a green chemical process employing low cost biomass precursors for the battery material manufacturing. The detailed results of the synthesis, characterization, and battery testing of the NMC powder materials will be presented.

25 ENERGY STORAGE↗

Nanostructured Powders Made from Flame Spray Pyrolysis for Li-Ion Cathode

Flame processes are the most economic ones to produce fine powders and have been used to produce pigment titanium oxide and fused silica in large volumes. In this work a flame spray pyrolysis (FSP) process is used to make positive electrode materials for Li-ion battery, which is made of complex metal oxide powders, such as Li(Ni1/3Mn1/3Co1/3)O2. In particular, the work was focused on making the NMC materials with stoichiometric compositions and desired morphologies. During the pyrolysis process different morphologies can be formed, involving often powders with primary nanoparticles. Such nanostructures were found to have affected the battery performance. Detailed results of the synthesis, characterization, and battery testing of the NMC powder materials will be presented.

25 ENERGY STORAGE↗

Steady Laminar Flame for 1-Step Thermal Decomposition Model of PBX 9501

We have recently developed a new 1-step thermal decomposition model of PBX 9501 high explosive. In this report, we examine the behavior of the model in 1-D steady laminar flame calculations. In particular, the dependencies of the steady laminar flame velocity on initial pressure, thermal conductivies and parameters of the thermal decomposition model are investigated. The results of our numerical calculations are compared to available experimental data.

42 ENGINEERING↗

Heat transfer through a box beam from an impinging hydrogen flame

An analysis was performed to determine whether a hydrogen jet flame impinging on a tunnel ceiling composed of multiple prestressed steel reinforced concrete box beams could result in permanent damage to the tunnel. The lower layer of the concrete box beam was modeled to determine whether heat reaches the steel reinforcing bars and whether spalling could occur. Heat transfer analysis shows that the temperature remains constant at the location of the steel reinforcing bars after 1.3 minutes of impingement and reaches a maximum of 130°C after 5 minutes. However, assuming a constant impingement for 5 minutes is an over estimation due the existing fire model which includes conservative assumptions. Explosive spalling may occur at a thin layer (~0.05 in. at 50 seconds, 0.1 in. at 5 minutes) at the bottom surface of the concrete box beam, but the steel reinforcing bars will not be exposed to the hydrogen flame.

42 ENGINEERING↗

Evaluation of flame propagation of retrofit energy efficient wall assemblies

Leveraging safety science experience and industry relationships, UL Solutions and the International Association of Fire Fighters (IAFF) initiated a joint project in 2022 under an agreement with the US Department of Energy to evaluate the flame propagation of retrofit energy efficient wall assemblies. A draft of the protocol from the ASTM work was used to test and comparatively study various retrofit energy efficient designs to gain a better understanding of their fire behavior. The goals of this study were as follows: Develop an understanding of fire propagation across new, cost effective, and energy efficient exterior retrofit wall assemblies. Refine the flame propagation draft test method for exterior wall assemblies based on ASTM E2707. Identify conditions that create fire propagation hazards in exterior wall assemblies and educate the fire service on the findings.

42 ENGINEERING↗

Predictive Modeling of NOx Emissions from Lean Direct Injection of Hydrogen and Hydrogen/Natural Gas Blends Using Flame Imaging and Machine Learning

This research paper explores the use of machine learning to relate images of flame structure and luminosity to measured NOx emissions. Images of reactions produced by 16 aero-engine derived injectors for a ground-based turbine operated on a range of fuel compositions, air pressure drops, preheat temperatures and adiabatic flame temperatures were captured and postprocessed. The experimental investigations were conducted under atmospheric conditions, capturing CO, NO and NOx emissions data and OH* chemiluminescence images from 27 test conditions. The injector geometry and test conditions were based on a statistically designed test plan. These results were first analyzed using the traditional analysis approach of analysis of variance (ANOVA). The statistically based test plan yielded 432 data points, leading to a correlation for NOx emissions as a function of injector geometry, test conditions and imaging responses, with 70.2% accuracy. As an alternative approach to predicting emissions using imaging diagnostics as well as injector geometry and test conditions, a random forest machine learning algorithm was also applied to the data and was able to achieve an accuracy of 82.6%. This study offers insights into the factors influencing emissions in ground-based turbines while emphasizing the potential of machine learning algorithms in constructing predictive models for complex systems.

08 HYDROGEN↗

Quantification of biogenic volatile organic compounds with a flame ionization detector using the effective carbon number concept

Biogenic volatile organic compounds (BVOCs) are emitted into the atmosphere by plants and include isoprene, monoterpenes, sesquiterpenes, and their oxygenated derivatives. These BVOCs are among the principal factors influencing the oxidative capacity of the atmosphere in forested regions. BVOC emission rates are often measured by collecting samples onto adsorptive cartridges in the field and then transporting these samples to the laboratory for chromatographic analysis. One of the most commonly used detectors in chromatographic analysis is the flame ionization detector (FID). For quantitative analysis with an FID, relative response factors may be estimated using the effective carbon number (ECN) concept. The purpose of this study was to determine the ECN for a variety of terpenoid compounds to enable improved quantification of BVOC measurements. A dynamic dilution system was developed to make quantitative gas standards of VOCs with mixing ratios from 20–55 ppb. For each experiment using this system, one terpene standard was co-injected with an internal reference, n-octane, and analyzed via an automated cryofocusing system interfaced to a gas chromatograph flame ionization detector and mass spectrometer (GC/MS/FID). The ECNs of 16 compounds (14 BVOCs) were evaluated with this approach, with each test compound analyzed at least three times. The difference between the actual carbon number and measured ECN ranged from -24% to -2%. Furthermore, the difference between theoretical ECN and measured ECN ranged from -22% to 9%. Measured ECN values were within 10% of theoretical ECN values for most terpenoid compounds.

47 OTHER INSTRUMENTATION↗

Flame zone of a composite propellant expanded by a laser source

Technique scales flame structure linearly with gas kinetic mean free path, which increases two to three orders of magnitude as pressure decreases like amount. Kinetic and transport time scales expand in proportion so that regression rates for laser-induced flames are two to three orders of magnitude slower.

Friedman, R.↗

Flame resistant elastic elastomeric fibers

Development of materials to improve flame resistance of elastic elastomeric fibers is discussed. Two approaches, synthesis of polyether based urethanes and modification of synthesized urethanes with flame ratardant additives, are described. Specific applications of both techniques are presented.

Howarth, J. T.↗

Measurement of temperature profiles in flames by emission-absorption spectroscopy

An investigation was conducted to explore the use of infrared and ultraviolet emission-absorption spectroscopy for determination of temperature profiles in flames. Spectral radiances and absorptances were measured in the 2.7-micron H2O band and the 3064-A OH band in H2/O2 flames for several temperature profiles which were directly measured by a sodium line-reversal technique. The temperature profiles, determined by inversion of the infrared and ultraviolet spectra, showed an average disagreement with line-reversal measurements of 50 K for the infrared and 200 K for the ultraviolet at a temperature of 2600 K. The reasons for these discrepancies are discussed in some detail.

Simmons, F. S.↗

Pressure waves generated by steady flames.

Analysis of pressure waves that can be generated by clouds of explosive gas mixtures in a free atmosphere which is initially at a uniform state. The treatment is restricted only to the final stage of constant flame velocity when the flowfield is self-similar. By the introduction of reduced blast-wave parameters as phase-plane coordinates, the problem is resolved into the determination of the appropriate integral curves on this plane. Results, including space profiles of gasdynamic parameters, have been computed for a specific case of a hydrocarbon-air mixture characterized by a specific heat ratio of 1.3, sound speed at NTP of 345 m/sec, and volumetric expansion ratio corresponding to constant pressure deflagration of 7. Maximum overpressure ratios that can be generated by such flames in point-and line-symmetrical waves range from .00053, for the lower bound in the burning speed, up to 6 for the deflagration, while, for the average speeds of 5 to 10 m/sec, they are at a level of 0.05 to 0.10.

Kuhl, A. L.↗