Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Diffusion rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Evaluation of transport conditions during physical vapor transport growth of opto-electronic crystals

Transport conditions were evaluated during the vapor phase growth of mercurous chloride crystals in a closed tube. Experimentally observed growth rates were much smaller than those calculated by the Hertz-Knudsen (H-K) equation. The Arrhenius behavior of growth rate with the temperature was used to derive the sticking coefficient. A one-dimensional diffusion model was used to calculate the total mass flux and was compared with the condensing flux. It was predicted that growth occurred in the convecto-diffusive range.

Singh, N. B.↗
NASA NTRS1990

Analysis of Pt/SnO(sub x) during catalysis of CO oxidation

Temperature-programmed reduction using 6kPaH2 suggests that a sample consisting of 3 percent Pt supported directly on SnO2 is, under conditions of catalysis of CO oxidation used here, best represented as 3 percent Pt/SnO sub x, since the support is likely to partially reduced, probably in the vicinity of the metal/oxide interface. Catalytic measurements at 421 to 424 K show that this 3 percent Pt/SnO sub x is significantly more active per unit area of Pt than 6 percent Pt/SiO2 in catalyzing the oxidation of CO. In situ micro-FTIR reveals that while the latter has predominantly linearly bound CO on the surface under reaction conditions, the Pt/SnO sub x also has a species absorbing at 2168 cm(exp -1) which may be CO upon Pt in a positive oxidation state or weakly chemisorbed CO on zero-valent Pt. This may be directly involved in the low temperature oxidation of CO on the Pt/SnO sub x, since being weakly held the activation energy for its surface diffusion to the metal/oxide interface will be low; such mobile species could allow the high rates of surface transport and an increase in the fraction of the surface over which the CO oxidation occurs. FTIR also reveals carbonate-type species on the P/SnO sub c surface.

Sermon, Paul A.↗
NASA NTRS1989

Ground evaluation of seeding an in-flight wingtip vortex using infrared imaging flow visualization technique

An experimental simulation of an in-flight wingtip vortical flow visualization technique uses infrared imaging to observe strong and concentrated vortices. This experiment is phase 1 of a two-phase infrared evaluation program. The system includes a vortex generator (model 320 Vortec Vortex Tube) which generates the required vortex. The mouth of the unit is mounted close to the free end of a half-inch diameter, sixteen and a half foot long stainless steel tubing (sized after tubing currently installed in the wings of an experimental Beechcraft Sundowner 180 aircraft). Dichloro difluoromethane (Freon-12) is entrained into the generated vortex. A breakdown of the vortices is indicated by the rapid diffusion and the resulting pattern is tracked using the infrared imager and video systems. Flow rates (volume and mass) are estimated at the laboratory and proposed flight conditions. The nominal flight altitude is expected to be 2500 feet.

Akinyanju, Ted↗
NASA NTRS1990

Stability of dendritic arrays

An approximate method for studying steady-state properties and linear stability of the dendritic arrays that are formed in directional solidification of alloys is proposed. This analysis is valid at high growth rates where the primary spacing between dendrites is larger than the velocity-dependent solutal diffusion length. A neutral stability boundary is computed and it is found that, in the situations where the results should be valid, the experimental data of Somboonsuk, et al. (1984) lie in the stable region, well away from the boundary.

Warren, James A.↗
NASA NTRS1990

Lifetime studies of high power rhodium/tungsten and molybdenum electrodes for application to AMTEC (alkali metal thermal-to-electric converter)

A detailed and fundamental model for the electrochemical behavior of AMTEC electrodes is developed which can aid in interpreting the processes which occur during prolonged operation of these electrodes. Because the sintering and grain growth of metal particles is also a well-understood phenomenon, the changes in electrode performance which accompany its morphological evolution may be anticipated and modeled. The grain growth rate observed for porous Mo AMTEC electrodes is significantly higher than that predicted from surface diffusion data obtained at higher temperatures and incorporated into the grain growth model. The grain growth observed under AMTEC conditions is also somewhat higher than that measured for Mo films on BASE (beta-alumina solid electrolyte) substrates in vacuum or at similar temperatures. Results of modeling indicate that thin Mo electrodes may show significant performance degradation for extended operation (greater than 10,000 h) at higher operating temperatures (greater than 1150 K), whereas W/Rh and W/Pt electrodes are expected to show adequate performance at 1200 K for lifetimes greater than 10,000 h. It is pointed out that current collection grids and leads must consist of refractory metals such as Mo and W which do not accelerate sintering or metal migration.

Williams, R. M.↗
NASA NTRS2000

Assessment of Remote Sensing Technologies for Location of Hydrogen and Helium Leaks

The objective of this initial phase of this research effort is to: 1) Evaluate remote sensing technologies for location of leaks of gaseous molecular hydrogen (H2) and gaseous helium (He) in air, for space transportation applications; and 2) Develop a diffusion model that predicts concentration of H2 or He gas as a function of leak rate and distance from the leak.

Sellar, R. Glenn↗
NASA NTRS2011

Magnetic Reconnection in a Compressible MHD Plasma

Using steady-state resistive MHD, magnetic reconnection is reinvestigated for conditions of high resistivity/low magnetic Reynolds number, when the thickness of the diffusion region is no longer small compared to its length. Implicit expressions for the reconnection rate and other reconnection parameters are derived based on the requirements of mass, momentum, and energy conservation. These expressions are solved via simple iterative procedures. Implications specifically for low Reynolds number/high resistivity are being discussed

Hesse, Michael↗
NASA NTRS2018

Relative Sputtering Rates of FeS, MgS, and Mg Silicates: Implications for ISM Gas Phase Depletions of Rock-Forming Elements

Astronomical measurements of S abundances in the diffuse interstellar medium (ISM) indicate ionized S is a dominant species with little (< 5%) S residing in grains (e.g. Jenkins 2009). This is an enigmatic result, given that abundant Fe-sulfide grains are observed in dust around pre- and post-main sequence stars and are also observed as major components of primitive meteoritic and cometary samples. These disparate observations suggest that the lifetime of sulfide grains in the ISM is short because of destruction processes. Our previous work has shown that FeS and MgS retain their crystallinity and do not amorphize during radiation processing, whereas enstatite and forsterite are readily amorphized. We have extended this study to measure the relative sputtering rates of FeS and MgS compared to enstatite and forsterite. Irradiation of FeS with 4 keV He+ results in preferential sputtering of S and the formation of a thin 2-3 nm, compact Fe metal layer that armors the surface. The zone of S loss extends to a depth of ~8-10 nm below the exposed surface. Despite this S loss, the FeS retains its crystallinity and shows no sign of incipient amorphization. Irradiation of FeS with 5kV Ga+ in a focused ion beam (FIB) instrument resulted in preferential sputtering of S and the formation of a 5-8-nm thick surface layer of nanophase Fe metal. X-ray mapping shows that the zone of S sputtering extends to a depth of nearly 20 nm, but there is no evidence for FeS amorphization, consistent with our previous work. The irradiation experiments show that the relative sputtering rate of FeS and MgS are much higher than olivine or enstatite. Sputtering experiments utilizing 30 kV and 5 kV Ga ions in the FIB produced volume loss in troilite that was ~4X greater than in enstatite or forsterite. The sputter yield under these conditions is such that for every Si atom sputtered from enstatite, ~14 S atoms are sputtered from FeS. We have performed similar sputtering experiments on Fe-bearing niningerite (MgS) and co-existing enstatite from the ALH 84170 EH3 chondrite. MgS also sputters much more rapidly than enstatite with a relative Si:S sputter yield of 1:8. For MgS, sulfur is highly depleted at the surface and the S-depletion zone extends to a depth of ~15 nm (using 5 kV Ga+). There is a corresponding zone of Mg and especially Fe enrichment that extends from 5 to ~10 nm below the surface, respectively. The dominant grain destruction mechanism in the ISM is sputtering from passage of supernova-generated shock waves. This process also results in the amorphization of crystalline silicates in the ISM. Our results indicate that FeS and MgS grains produced in evolved stars and injected into the ISM will be destroyed more rapidly than crystalline silicates. This process may account for the lack of significant depletion of S from the gas phase in the ISM. However, rare nanophase FeS grains occur as inclusions in circumstellar amorphous silicate grains found in comet dust particles analyzed in the laboratory. These results show that a finite amount of S in the ISM is sequestered in solid grains.

SPUTTERING RATES↗
NASA NTRS1996

Ignition Delay Associated with a Strained Strip

Ignition processes associated with two adjacent fuel-oxidizer interferences bounding a strained fuel strip are explored here using single-step activation energy asymptotics. Calculations are made for constant as well as temporally decaying strain fields. There possible models of ignition are determined: one in which the two interfaces ignite independently as diffusion flames; one in which the two interfaces ignite dependently and in which ignition occurs to form a single , premixed flame at very high strain rates before ignition is completely prevented. In contrast to a single, isolated interface in which ignition can be prevented by overmatching heat production with heat convection due to strain, ignition of a strained fuel strip can also be prevented if the finite extend of fuel is diluted by oxidizer more quickly than heat production can cause a positive feedback thermal runaway. These behaviors are dependent on the relative sizes of timescales associated with species and heat diffusion, with convection due to strain, and with the chemical reaction. The result here indicate that adjacent, strained species interfaces may ignite quite differently in nature from ignition of a single, strained intrface and that their interdependence should be considered as the interfaces are brought closer together in complex strain fields. Critical strain rates leading to complete ignition delay are found to be considerably smaller for the fuel strip than those for single interfaces as the fuel strip is made thin in comparison to diffusion and chemical length scales.

Gerk, T. J.↗
DOE OSTI2020

Surface Amorphization of Vanadium Dioxide (B) for K-ion Battery

Given the merits of low cost, fast ionic transport in electrolyte, and high operating voltage, potassium ion batteries (PIBs) are promising alternatives to lithium-ion batteries. However, developing suitable electrode materials that can reversibly accommodate large potassium ions is a great challenge. In this paper, guided by density functional theory (DFT) calculations, it is demonstrated that the strategy of interfacial engineering via surface amorphization of VO 2 (B) nanorods (SA-VO 2 ), which results in the formation of a crystalline core/amorphous shell heterostructure, enables superior K + storage performance in terms of large capacity, outstanding rate capability, and long cycle stability working as an anode for PIBs. DFT calculations reveal that the created crystalline/amorphous heterointerface in SA-VO 2 can substantially lower the surface energy, narrow the band gap, and reduce the K + diffusion barrier of VO 2 (B). These conditions enable enhanced K + storage capacity and rapid K + /electron transfer, which result in large capacity and outstanding rate capability. Using in situ X-ray diffraction and in situ transmission electron microscopy complemented by ex situ microscopic and spectroscopic techniques, it is unveiled that the superior cycling stability originates from the excellent phase reversibility with negligible strain response and robust mechanical behavior of SA-VO 2 upon (de)potassiation.

25 ENERGY STORAGE↗
NASA NTRS1971

Electron pitch-angle diffusion driven by oblique whistler-mode turbulence.

A general description of cyclotron harmonic resonant pitch-angle scattering is presented. Quasi-linear diffusion coefficients are prescribed in terms of the wave normal distribution of plasma wave energy. Numerical computations are performed for the specific case of relativistic electrons interacting with a band of low frequency whistler-mode turbulence. A parametric treatment of the wave energy distribution permits normalized diffusion coefficients to be presented graphically solely as a function of the electron pitch-angle. The diffusion coefficients generally decrease with increasing cyclotron harmonic number. Higher harmonic diffusion is insignificant at very small electron pitch-angles, but becomes increasingly important as the pitch-angle increases. One thus expected the rate of pitch-angle scattering to decrease with increasing electron energy, since the resonant value of the latter varies proportionately with harmonic number. This indicates that, in mirror-type magnet field geometrics, such as the earth's radiation belts, the diffusion losses of high energy electrons are likely to be appreciably slower than those at low energy.

Lyons, L. R.↗
NASA NTRS1979

Effect of pressure on structure and NO sub X formation in CO-air diffusion flames

A study was made of nitric oxide formation in a laminar CO-air diffusion flame over a pressure range from 1 to 50 atm. The carbon monoxide (CO) issued from a 3.06 mm diameter port coaxially into a coflowing stream of air confined within a 20.5 mm diameter chimney. Nitric oxide concentrations from the flame were measured at two carbon monoxide (fuel) flow rates: 73 standard cubic/min and 146 sccm. Comparison of the present data with data in the literature for a methane-air diffusion flame shows that for flames of comparable flame height (8 to 10 mm) and pseudoequivalence ratio (0.162), the molar emission index of a CO-air flame is significantly greater than that of a methane-air flame.

Maahs, H. G.↗
NASA NTRS1987

Gamma-ray constraints on Na-22 yields in nova explosions

The longitudinal distribution of diffuse 1.275 MeV emission produced by the decay of interstellar Na-22 generated by a limited class of energetic novae-accreting ONeMg white dwarfs is modeled. The probability distributions for the locations of disk novae are derived as functions of Galactocentric cylindrical coordinates. The occurrence rate for novae of all classes in the Galactic disk is about 30/yr. An occurrence rate of about 16/yr is found for spheroid novae of all classes. By comparing these simulation results with HEAO 3 upper limits on diffuse 1.275 MeV emission, upper limits of (3-5.6) x 10 to the -7th solar mass are determined for the mean Na-22 yield for energetic novae generated by accreting ONeMg white dwarfs. These Na-22 limits constrain future models of explosive nucleosynthesis in energetic nova explosions.

Higdon, J. C.↗
DOE OSTI2020

Generalized hydrodynamic analysis of transport through a finite open nanopore for two-component single-file systems

Single-file diffusion (SFD) in finite open nanopores is characterized by nonzero spatially varying tracer diffusion coefficients within a generalized hydrodynamic description. This contrasts with infinite SFD systems where tracer diffusivity vanishes. In standard tracer counterpermeation (TCP) analysis, two reservoirs, each containing a different species, are connected to opposite ends of a finite pore. Here, we implement an extended TCP analysis to allow the two reservoirs to contain slightly different mixtures of the two species. Then, determination of diffusion fluxes through the pore allows extraction of diffusion coefficients for near-constant partial concentrations of the two species. This analysis is applied for a lattice-gas model describing two-component SFD through a finite linear pore represented by a one-dimensional array of cells. Two types of particles, A and B, can hop only to adjacent empty cells with generally different rates, $h_A$ and $h_B$. Particles are noninteracting other than exclusion of multiple cell occupancy. Results reveal generalized hydrodynamic tracer diffusion coefficients which adopt small values inversely proportional to pore length in the pore center, but which are strongly enhanced near pore openings.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Cation Disordered Anti-Perovskite Cathode Materials with Enhanced Lithium Diffusion and Suppressed Phase Transition

Recently, a new family of anti-perovskite Li 2 TMSO was discovered as promising cathode materials for Li-ion batteries (LIBs) with superiorities in high specific capacity, low cost, and environmental friendliness. However, the applications of these anti-perovskite materials meet severe challenges in the cyclability and rate performance. In this work, a cation-disordered anti-perovskite type solid solution Li 2 Fe 1– x Mn x SO (LFMSO, x = 0, 0.2, 0.5) with excellent electrochemical performance is reported. On the basis of comprehensive structural characterizations, the role of the cation disordering in LFMSO is clarified. In comparison with Li 2 FeSO (LFSO), the reduced Li-ion diffusion barrier and the increased Li-rich octahedral configurations in LFMSO with higher configurational entropy imply the facilitated long-range Li-ion diffusion and the suppressed phase transition, which favor the high-rate capability and cycling stability. In addition, the large lattice distortion and Coulombic interaction between the anions and cations lead to the breathing of the unit cell during charge/discharge. The variation of the unit cell volume decreases to 2.5% upon Li-ion delithiation. A superstructure is observed in LFMSO for the first time. These findings help to pave the way for the research and development of novel cathode materials for the next generation LIBs.

25 ENERGY STORAGE↗
DOE OSTI2023

An Analytic Formula for Entraining CAPE in Midlatitude Storm Environments

Abstract This article introduces an analytic formula for entraining convective available potential energy (ECAPE) with an entrainment rate that is determined directly from an environmental sounding, rather than prescribed by the formula user. Entrainment is connected to the background environment using an eddy diffusivity approximation for lateral mixing, updraft geometry assumptions, and mass continuity. These approximations result in a direct correspondence between the storm-relative flow and the updraft radius and an inverse scaling between the updraft radius squared and entrainment rate. The aforementioned concepts, combined with the assumption of adiabatic conservation of moist static energy, yield an explicit analytic equation for ECAPE that depends entirely on state variables in an atmospheric profile and a few constant parameters with values that are established in past literature. Using a simplified Bernoulli-like equation, the ECAPE formula is modified to account for updraft enhancement via kinetic energy extracted from the cloud’s background environment. CAPE and ECAPE can be viewed as predictors of the maximum vertical velocity w max in an updraft. Hence, these formulas are evaluated using w max from past numerical modeling studies. Both of the new formulas improve predictions of w max substantially over commonly used diagnostic parameters, including undiluted CAPE and ECAPE with a constant prescribed entrainment rate. The formula that incorporates environmental kinetic energy contribution to the updraft correctly predicts instances of exceedance of by w max , and provides a conceptual explanation for why such exceedance is rare among past simulations. These formulas are potentially useful in nowcasting and forecasting thunderstorms and as thunderstorm proxies in climate change studies. Significance Statement Substantial mixing occurs between the upward-moving air currents in thunderstorms (updrafts) and the surrounding comparatively dry environmental air, through a process called entrainment. Entrainment controls thunderstorm intensity via its diluting effect on the buoyancy of air within updrafts. A challenge to representing entrainment in forecasting and predictions of the intensity of updrafts in future climates is to determine how much entrainment will occur in a given thunderstorm environment without a computationally expensive high-resolution simulation. To address this gap, this article derives a new formula that computes entrainment from the properties of a single environmental profile. This formula is shown to predict updraft vertical velocity more accurately than past diagnostics, and can be used in forecasting and climate prediction to improve predictions of thunderstorm behavior and impacts.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1981

Energetic oxygen and sulfur ions in the Jovian magnetosphere

Observations of 1 to 20 MeV/nuc oxygen, sodium, and sulfur ions in the Jovian magnetosphere are reported. Measurements made by the cosmic ray subsystem on Voyager 1 and 2 were used to calculate abundances and energy spectra in the region from 5 to 20 Jovian radii. The phase space density of the oxygen ions calculated from the spectra has a positive radial gradient between 6 and 17 Jovian radii, indicating an inward diffusive flow. The diffusion coefficient upper limit at 9 Jovian radii is approximately 10 to the -5 power/s. This limit, combined with the analysis of Voyager plasma observations by Siscoe et al.1981, implies an upper limit to the mass loading rate near Io of approximately 10 to the 28th power ions/s. The energetic oxygen lifetime is within an order of magnitude of the strong pitch-angle diffusion lifetime in this region, with the largest total number of particles lost between 7.5 and 12.5 Jovian radii. It is shown that the losses are not due to geometric absorption by Io, absorption by dust grains, or energy loss in the plasma of the inner magnetosphere, and it is therefore postulated that the primary loss mechanism is pitch-angle scattering into the loss cone.

Gehrels, N.↗
DOE OSTI2024

Effect of microalloying additions on microstructural evolution and thermal stability in cast Al-Ni alloys

Enhancement of thermal stability in Al-Ni alloys through microalloying with slow-diffusing elements, specifically Zr, has been previously reported which is attributed to Zr segregation at the Al/Al 3 Ni interface. In this study, we explore the influence of microalloying Al-Ni alloys with Zr, Ti, V, and Fe on microstructural evolution, hardness, and electrical and thermal conductivity across a range of heat-treatment temperatures from 300 to 450 °C. The distribution of microalloying elements and precipitates after heat treatment is characterized using atom probe tomography (APT). Our investigation confirms Zr segregation to the Al/Al 3 Ni interface, while similar interfacial segregation is absent with the addition of Ti, V, and Fe. Additionally, our analysis of the Al 3 Ni microfiber morphology reveals that their coarsening and spheroidization rates are similar with and without interfacial segregation; thus, retaining the fiber reinforcement through interfacial segregation of slow diffusing elements may not be an effective strategy. Precipitation of L1 2 nanoparticles was found to be the dominant mechanism affecting enhanced hardness and electrical conductivity in Al-Ni-Zr alloys, attributed to precipitation strengthening and solute depletion, respectively. Similar precipitation was not observed for additions of Ti, V, and Fe following heat treatment. We provide a thermodynamic explanation for this limitation. Furthermore, the findings of this study suggest that an effective approach for designing Al-Ni alloys should involve prioritizing microalloying elements to maximize L1 2 precipitation and minimize solute content in the FCC-Al matrix post heat treatment, rather than focusing on Al/Al3Ni interfacial segregation.

36 MATERIALS SCIENCE↗