Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data Analytics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

In-Flight Characterization of the Electromagnetic Environment Inside an Airliner

In 1995, the NASA Langley Research Center conducted a series of experimental measurements that characterized the electromagnetic environment (EME) inside a Boeing 757 airliner while in flight, Measurements were made of the electromagnetic energy coupled into a commercially configured aircraft as it was flown in close proximity to ground-based radio frequency (RF) transmitters operating at approximately 26, 173. and 430 MHz. The goal of this experiment was to collect data for the verification of analytical predictions of the internal aircraft response to an external stimulus. This paper describes the experiment, presents the data collected by it, and discusses techniques used to compute both the magnitude of the electric field illuminating the aircraft and its direction of propagation relative to a coordinate system fixed to the aircraft. The latter is determined from Global Positioning System (GPS) and aircraft Inertial Reference Unit (IRU) data. The paper concludes with an examination of the shielding effectiveness of the test aircraft. as determined by comparison of' the measured internal EME and computed external EME.

Moeller, Karl J.↗
NASA NTRS2003

Material Damping Experiments at Cryogenic Temperatures

A unique experimental facility has been designed to measure damping of materials at cryogenic temperatures. The test facility pays special attention to removing other sources of damping in the measurement by avoiding frictional interfaces, decoupling the test specimen from the support system, and by using a non-contacting measurement device; Damping data is obtained for materials (AI, GrEp, Be, Fused Quartz), strain amplitudes (less than 10-6 ppm), frequencies (20Hz-330Hz) and temperatures (20K-293K) relevant to future precision optical space missions. The test data shows a significant decrease in viscous damping at cryogenic temperatures and can be as low as 10-4%, but the amount of the damping decrease is a function of frequency and material. Contrary to the other materials whose damping monotonically decreased with temperature, damping of Fused Quartz increased substantially at cryo, after reaching a minimum at around l50 K. The damping is also shown to be insensitive to strain for low strain levels. At room temperatures, the test data correlates well to the analytical predictions of the Zener damping model. Discrepancies at cryogenic temperatures between the model predictions and the test data are observed.

cryogenic↗
DOE OSTI2024

DECOVALEX-2023: Task C Final Report

The Full-scale Emplacement (FE) heater experiment at the Mont Terri Underground Rock Laboratory (URL) was designed and conducted by Nagra to replicate an emplacement tunnel of Nagra’s reference repository design at 1:1 scale. Alongside testing the technical feasibility of constructing disposal tunnels, emplacing waste containers in the tunnels and then backfilling them, the main goals of the FE experiment are (1) to obtain a better understanding of the coupled effects of induced thermo-hydro-mechanical (THM) processes that may occur and (2) to validate existing coupled THM models (Müller et al., 2017). A key aspect of ensuring safety for repositories located in low-permeability rock involves minimizing any damage to the rock itself, thereby preserving its integrity and promoting a stable environment Amongst a number of processes that could damage the rock is the increase in pore pressure due to thermal loading caused by heat emitted from the waste. To reduce the potential damage of the rock, it is important to analyse the evolution of heat over time due to the heat load of the containers and assess possible consequences by coupled THM models. The aim of Task C of DECOVALEX-2023 was to build 3D numerical models of the FE experiment, focussing in particular on the heating induced pore pressure change in the Opalinus Clay. Data from a large number of sensors were available from the FE experiment for model comparison. These sensors measured temperature and relative humidity in the bentonite around the heaters, and temperature, pressure and displacement/strain in the surrounding Opalinus clay. Data were available from the start of excavation (April 2012) up to August 2020 for most sensors (more than 5 years from the start of heating in December 2014). To fulfil the overall aim of the task, the work was broken down into a number of steps, starting with simpler models to build confidence in each team’s approach and then moving to more complex models that better represent the FE experiment. Step 0 consisted of 2D benchmark models, gradually increasing the number of processes that are represented from thermal (T) only models in Step 0a, to coupled thermal hydraulic (TH) models in Step 0b with a representation of changing porosity, to coupled thermo-hydro-mechanical (THM) models in Step 0c, where porosity changes are calculated by the mechanical model. A detailed specification of processes, parameters, initial and boundary conditions was provided for this step, with the ambition that all teams would work towards close agreement in their model results, thus building confidence in the model implementations. vi It was not straightforward to achieve agreement between the teams, so additional steps (Step 0b2, 0b3, 0c2, 0c3) were added along with derivation of some analytical solutions against which the models could be compared. The reasons for the differences between teams were investigated and found to be caused primarily by different conceptual model assumptions (including temperature dependence of the thermal expansion of water), different model formulations (including porosity evolution) and differences in modelled domain sizes, boundary conditions and grid discretisation. This demonstrates that comparisons between multiple modelling teams and/or comparison with analytical results and experimental data are highly beneficial in providing an indication of uncertainty in model predictions. At the conclusion of Step 0, almost all teams had achieved a close agreement in model results and those that had not achieved an agreement knew the reason for this. Step 1 moved from 2D models to 3D models of the FE experiment without adding technical features like shotcrete or EDZ, and only considering the heating phase. Initially the 3D model was tightly specified to continue to build confidence in the model implementations (Step 1a). The results of Step 1a were compared to the data from the FE-experiment without the teams seeing the data. The teams were then provided with a sub-set of the data from the FE-experiment and invited to consider how best to use the large dataset for model comparison (Step 1b). Teams were then asked to use the data provided to calibrate their models, only changing material property values rather than adding features or processes to their models (Step 1c). In Step 1, teams were asked to only model the heating phase of the experiment, so pressure in the Opalinus Clay was reported as change in pressure since the initial conditions were specified rather than modelled. The change from 2D to 3D models was accompanied by an increase in the dispersion of results between the teams. Some of this was resolved during the task, but some remained and is potentially due to model discretisation. Calibration of parameters was useful in improving the fit of the models to the data but the remaining differences indicated that the models were missing features or processes. In Step 2, the teams were asked to update their models with additional features and processes as well as calibrating parameters to try and improve the fit of the models to the data. Teams were encouraged to represent ventilation of the open FE tunnel prior to backfilling with heaters and bentonite and in Step 2, the absolute pressure in the Opalinus Clay was compared between the teams. Teams took different approaches, but there was consideration of adding shotcrete and an EDZ into the model, representing stress change during excavation and different approaches to modelling ventilation of the FE tunnel. Overall, the documented results showed a very good agreement for temperature. The results for porewater pressure evolution showed a significant improvement for most teams compared to Step 1c with a good agreement to the measurements for several teams whereas some teams overpredicted the pressure increase and others overpredicted the drainage effect especially for the sensors close to the heater. Step 3 was an opportunity for teams to use the models developed in Step 1 and Step 2 to make predictions about the temperature and pressure changes that will be expected at the FE experiment over the next few years in light of the planned changes in thermal output of the heaters.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Side-by-Side Comparison of Subhourly Clipping Models

Over the past several years there have been numerous attempts at quantifying the inherent power clipping of inverters due to subhourly irradiance variability that is not captured in hourly PV performance models. Different models have been proposed to correct for these clipping losses in PV performance estimates, including matrix lookup models, distribution modeling of the PV power performance within a given hour, and machine learning methods. To date, there have been few comprehensive quantitative comparisons of these inverter clipping correction modeling approaches to evaluate the effectiveness of these approaches in predicting the actual behavior of PV system inverter clipping. In this study, we perform such a comparison, evaluating the Allen and Walker correction loss modeling approaches recently implemented in the System Advisor Model (SAM) against clipping losses modeled with 1-minute climate data. These comparisons were performed across a variety of climate locations and inverter loading ratios to thoroughly analyze the effectiveness of these modeling approaches relative to each other. Results from this analysis reveal that both clipping correction approaches improve annual energy accuracy to within 2% of 1-minute modeled energy yield. The two models predict annual clipping loss more accurately than simple hourly power limit clipping, with the Allen method typically being slightly more accurate at typical ILR values and the Walker method often being slightly more accurate at high ILR values The models can improve accuracy over the status quo clipping approach up to 3 percentage points in systems with ILR of 2.0, showing the importance of this modeling factor in energy yield estimates.

accuracy↗
DOE OSTI2020

Real Time Effective Impedance Estimation for Power System State Estimation

Here, we introduce two tools-the Effective Impedance State Estimator (EISE), and the Real Time Effective Impedance Estimator (RTEIE). The EISE is novel in that it is an entirely data-driven state estimator, and does not require a network model. Thus, the EISE is well suited for applications in which an accurate network model is not available. Instead of using a network impedance model, the EISE uses an effective impedance network model that is learned online by the RTEIE. The RTEIE recursively estimates the effective impedance network model using phasor measurement unit (PMU) measurements. The mathematical reasoning for using an effective impedance model, rather than a full network impedance model, is given. The recursive estimation framework allows the RTEIE to take the entire history of phasor measurements into account to produce a model estimate, while still adjusting to changes in the network impedance due to external factors such as topology changes and temperature. The merits of the RTEIE and EISE are demonstrated by comparing the accuracy of the EISE with a conventional state estimator on a toy network.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2023

Tutorial: Lessons Learned for Behavior Analysts from Data Scientists

Big data is a computing term used to refer to large and complex data sets, typically consisting of terabytes or more of diverse data that is produced rapidly. The analysis of such complex data sets requires advanced analysis techniques with the capacity to identify patterns and abstract meanings from the vast data. The field of data science combines computer science with mathematics/statistics and leverages artificial intelligence, in particular machine learning, to analyze big data. This field holds great promise for behavior analysis, where both clinical and research studies produce large volumes of diverse data at a rapid pace (i.e., big data). This article presents basic lessons for the behavior analytic researchers and clinicians regarding integration of data science into the field of behavior analysis. We provide guidance on how to collect, protect, and process the data, while highlighting the importance of collaborating with data scientists to select a proper machine learning model that aligns with the project goals and develop models with input from human experts. Here, we hope this serves as a guide to support the behavior analysts interested in the field of data science to advance their practice or research, and helps them avoid some common pitfalls.

42 ENGINEERING↗
NASA NTRS1985

Three-dimensional inviscid analysis of radial turbine flow and a limited comparison with experimental data

The three-dimensional inviscid DENTON code is used to analyze flow through a radial-inflow turbine rotor. Experimental data from the rotor are compared with analytical results obtained by using the code. The experimental data available for comparison are the radial distributions of circumferentially averaged values of absolute flow angle and total pressure downstream of the rotor exit. The computed rotor-exit flow angles are generally underturned relative to the experimental values, which reflect the boundary-layer separation at the trailing edge and the development of wakes downstream of the rotor. The experimental rotor is designed for a higher-than-optimum work factor of 1.126 resulting in a nonoptimum positive incidence and causing a region of rapid flow adjustment and large velocity gradients. For this experimental rotor, the computed radial distribution of rotor-exit to turbine-inlet total pressure ratios are underpredicted due to the errors in the finite-difference approximations in the regions of rapid flow adjustment, and due to using the relatively coarser grids in the middle of the blade region where the flow passage is highly three-dimensional. Additional results obtained from the three-dimensional inviscid computation are also presented, but without comparison due to the lack of experimental data. These include quasi-secondary velocity vectors on cross-channel surfaces, velocity components on the meridional and blade-to-blade surfaces, and blade surface loading diagrams. Computed results show the evolution of a passage vortex and large streamline deviations from the computational streamwise grid lines. Experience gained from applying the code to a radial turbine geometry is also discussed.

Choo, Y. K.↗
NASA NTRS1985

Three-dimensional inviscid analysis of radial-turbine flow and a limited comparison with experimental data

The three-dimensional inviscid DENTON code is used to analyze flow through a radial-inflow turbine rotor. Experimental data from the rotor are compared with analytical results obtained by using the code. The experimental data available for comparison are the radial distributions of circumferentially averaged values of absolute flow angle and total pressure downstream of the rotor exit. The computed rotor-exit flow angles are generally underturned relative to the experimental values, which reflect the boundary-layer separation at the trailing edge and the development of wakes downstream of the rotor. The experimental rotor is designed for a higher-than-optimum work factor of 1.126 resulting in a nonoptimum positive incidence and causing a region of rapid flow adjustment and large velocity gradients. For this experimental rotor, the computed radial distribution of rotor-exit to turbine-inlet total pressure ratios are underpredicted due to the errors in the finite-difference approximations in the regions of rapid flow adjustment, and due to using the relatively coarser grids in the middle of the blade region where the flow passage is highly three-dimensional. Additional results obtained from the three-dimensional inviscid computation are also presented, but without comparison due to the lack of experimental data. These include quasi-secondary velocity vectors on cross-channel surfaces, velocity components on the meridional and blade-to-blade surfaces, and blade surface loading diagrams. Computed results show the evolution of a passage vortex and large streamline deviations from the computational streamwise grid lines. Experience gained from applying the code to a radial turbine geometry is also discussed.

Choo, Y. K.↗
NASA NTRS1988

Evaluation of the international reference ionosphere with the large AE-C and DE2 data bases

Empirical models such as the International Reference Ionosphere (IRI) are synthesized from large data bases. They can be viewed as analytical tools to facilitate accessing information stored in the data banks. However, in establishing the models, one has to apply smoothing and averaging procedures that in effect reduce the original information content. This study evaluates the agreement between the data base and the model at two opposite extremes of time resolution. Electron densities and temperatures in the altitude range of 300 to 400 km predicted by the IRI and measured by the AE-C and DE 2 satellites on the level of individual orbits as well as on the level of mission averages are compared. Whereas the averages show excellent agreement, the comparison for individual measurements indicates the limitations of empirical models.

Bilitza, D.↗
NASA NTRS2012

A Peculiar Class of Debris Disks from Herschel/DUNES: A Steep Fall Off in the Far Infrared

Context. The existence of debris disks around old main sequence stars is usually explained by continuous replenishment of small dust grains through collisions from a reservoir of larger objects. Aims. We present photometric data of debris disks around HIP 103389 (HD199260), HIP 100350 (HN Peg, HD206860), and HIP 114948 (HD 219482), obtained in the context of our Herschel Open TIme Key Program DUNES (DUst around NEarby Stars). Methods. We used Herschel/PACS to detect the thermal emission of the three debris disks with a 30 sigma sensitivity of a few mJy at l00 micron and 160 micron. In addition, we obtained Herschel/PACS photometric data at 70 micron for HIP 103389. These observations are complemented by a large variety of optical to far-infrared photometric data. Two different approaches are applied to reduce the Herschel data to investigate the impact of data reduction on the photometry. We fit analytical models to the available spectral energy distribution (SED) data using the fitting method of simulated therma1 annealing as well as a classical grid search method. Results. The SEDs of the three disks potentially exhibit an unusually steep decrease at wavelengths >= 70 micron. We investigate the significance of the peculiar shape of these SEDs and the impact on models of the disks provided it is real. Using grain compositions that have been applied successfully for modeling of many other debris disks, our modeling reveals that such a steep decrease of the SEDs in the long wavelength regime is inconsistent with a power-law exponent of the grain size distribution -3.5 expected from a standard equilibrium collisional cascade. In contrast, a steep grain size distribution or, alternatively an upper grain size in the range of few tens of micrometers are implied. This suggests that a very distinct range of grain sizes would dominate the thermal. emission of such disks. However, we demonstrate that the understanding of the data of faint sources obtained with Herschel is still incomplete and that the significance of our results depends on the version of the data reduction pipeline used. Conclusions. A new mechanism to produce the dust in the presented debris disks, deviations from the conditions required for a standard equilibrium collisional cascade (grain size exponent of -3.5), and/or significantly different dust properties would be necessary to explain the potentially steep SED shape of the three debris disks presented.

Ertel, S.↗
NASA NTRSDate not supplied

Biological Research and Space Health Enabled by Machine Learning to Support Deep Space Missions

A key science goal of the NASA “Moon to Mars” campaign is to understand how biology responds to the Lunar, Martian, and deep space environments in order to advance fundamental knowledge, reduce risk, and support safe, productive human space missions. Through the powerful emerging approaches of artificial intelligence (AI) and machine learning (ML), a paradigm shift has begun in biomedical science and engineered astronaut health systems, to enable Earth independence and autonomy of mission operations. Here we present an overview of AI/ML architecture to support deep space mission goals, developed with leaders in the field. First, we focus on the fundamental biological research that supports our understanding of physiological responses to spaceflight, and we describe current efforts to support AI/ML research including data standardization and data engineering through maximally open and FAIR (findable, accessible, interoperable, reusable) databases and the generation of AI-ready datasets for reuse and analysis. We also discuss remote data management frameworks for research data as well as environmental and health data that are generated during deep space missions. We highlight several research projects that leverage data standardization and management for fundamental biological discovery to uncover the complex effects of space travel on living systems. Next, we provide an overview of cutting-edge AI/ML approaches that can be integrated to support remote monitoring and analysis during deep space missions, including generative models and large language models to learn the underlying biomedical patterns and predict outcomes or answer questions during off world medical scenarios. We also describe current AI/ML methods to support this research and monitoring through automated cloud-based labs which enable limited human intervention and closed-loop experimentation in remote settings. These labs could support mission autonomy by analyzing environmental data streams, and would be facilitated through in situ analytics capabilities to avoid sending large raw data files through low bandwidth communications. Finally, in the context of deep space missions with limited communications or access to medical advice from Earth, we describe a solution for integrated, real-time mission biomonitoring across hierarchical levels from continuous environmental monitoring, to wearables and point-of-care devices, to molecular and physiological monitoring. We introduce a precision space health system that will ensure that the future of space health is predictive, preventative, participatory and personalized.

artificial intelligence↗
DOE OSTI2024

Data for Root Exudation Links Root Traits to Soil Functioning in Agroecosystems

Root exudation is a key process for plant nutrient acquisition, but the controls on root exudation and its relationship to soil C and N processes in agroecosystems are unclear. We hypothesized that root exudation rates would be related to root morphological traits, N fertilization, and soil moisture. We also anticipated that root exudation would be correlated with bulk soil enzyme activity. Root exudation, root traits, and bulk soil extracellular enzyme activity were assessed in maize (Zea mays L.), soybean (Glycine max (L.) Merr.), biomass sorghum (Sorghum bicolor (L.) Moench), giant miscanthus (Miscanthus × giganteus), and switchgrass (Panicum virgatum L.). Measurements were taken in situ during two growing seasons with contrasting precipitation regimes, and N fertilization rate was varied in sorghum during one year. Specific root exudation (per unit root surface area) was negatively related to root diameter and was generally higher in annuals than perennials. Sorghum N fertilization did not affect root exudation rates, and soil moisture regime had no effect on annual root exudation rates within maize, sorghum, and miscanthus. Specific root exudation was negatively related to bulk soil C- and N-degrading soil enzyme activities. Intrinsic plant characteristics appeared more important than environmental variables in controlling in situ root exudation rates. The relationships between root diameter, root exudation, and soil C and N processes link root morphological traits to soil functions and demonstrate the potential tradeoffs among plant nutrient acquisition strategies in agroecosystems.

Biomass Analytics↗
DOE OSTI2021

Data from Genotype-Environment-Management Interactions in Biomass Yield and Feedstock Composition of Photoperiod-Sensitive Energy Sorghum

Recently introduced photoperiod-sensitive (PS) biomass sorghum ( Sorghum bicolor L. Moench) needs to be investigated for yield potential under different cultivation environments with reasonable nitrogen (N) inputs. The objectives of this study were to (1) evaluate the biomass yield and feedstock quality of four sorghum hybrids with different levels of PS ranging from very PS (VPS) hybrids and to moderate PS (MPS) hybrids, and (2) determine the optimal N inputs (0~168 kg N ha−1) under four environments: combinations of both temperate (Urbana, IL) and subtropical (College Station, TX) regions during 2018 and 2019. Compared to TX, the PS sorghums in central IL showed higher yield potential and steady feedstock production with an extended day length and with less precipitation variability, especially for the VPS hybrids. The mean dry matter (DM) yields of VPS hybrids were 20.5 Mg DM ha−1 and 17.7 Mg DM ha−1 in IL and TX, respectively. The highest N use efficiency occurred at a low N rate of 56 kg N ha−1 by improving approximately 33 kg DM ha−1 per 1.0 kg N ha−1 input. Approximately 70% of the PS sorghum biomass can be utilized for biofuel production, consisting of 58-65% of the cell-wall components and 4-11% of the soluble sugar. This study demonstrated that the rainfed temperate area (e.g., IL) has a great potential for the sustainable cultivation of PS energy sorghum due to their observed high yield potential, stable production, and low N requirements.

Biomass Analytics↗
NASA NTRS1992

Heat pipe performance experiment

The objective of the heat pipe performance experiment is to answer questions about how heat pipe performance in space differs from heat pipe performance on the ground. This part of the experiment will attempt to account for the following: (1) gravity domination in ground testing; (2) surface tension domination in a microgravity environment; and (3) the effects of underfill and overfill. The secondary objective of the experiment is to obtain quantitative data for axial groove and porous wick heat pipes in a microgravity environment for comparison with the following: (1) analytical models; (2) ground test data; and (3) existing flight data.

Fleischman, George↗
NASA NTRS2015

From Pixels to Planets

The Kepler Mission was launched in 2009 as NASAs first mission capable of finding Earth-size planets in the habitable zone of Sun-like stars. Its telescope consists of a 1.5-m primary mirror and a 0.95-m aperture. The 42 charge-coupled devices in its focal plane are read out every half hour, compressed, and then downlinked monthly. After four years, the second of four reaction wheels failed, ending the original mission. Back on earth, the Science Operations Center developed the Science Pipeline to analyze about 200,000 target stars in Keplers field of view, looking for evidence of periodic dimming suggesting that one or more planets had crossed the face of its host star. The Pipeline comprises several steps, from pixel-level calibration, through noise and artifact removal, to detection of transit-like signals and the construction of a suite of diagnostic tests to guard against false positives. The Kepler Science Pipeline consists of a pipeline infrastructure written in the Java programming language, which marshals data input to and output from MATLAB applications that are executed as external processes. The pipeline modules, which underwent continuous development and refinement even after data started arriving, employ several analytic techniques, many developed for the Kepler Project. Because of the large number of targets, the large amount of data per target and the complexity of the pipeline algorithms, the processing demands are daunting. Some pipeline modules require days to weeks to process all of their targets, even when run on NASA's 128-node Pleiades supercomputer. The software developers are still seeking ways to increase the throughput. To date, the Kepler project has discovered more than 4000 planetary candidates, of which more than 1000 have been independently confirmed or validated to be exoplanets. Funding for this mission is provided by NASAs Science Mission Directorate.

supercomputers↗
NASA NTRS1995

Using object-oriented analysis to design a multi-mission ground data system

This paper describes an analytical approach and descriptive methodology that is adapted from Object-Oriented Analysis (OOA) techniques. The technique is described and then used to communicate key issues of system logical architecture. The essence of the approach is to limit the analysis to only service objects, with the idea of providing a direct mapping from the design to a client-server implementation. Key perspectives on the system, such as user interaction, data flow and management, service interfaces, hardware configuration, and system and data integrity are covered. A significant advantage of this service-oriented approach is that it permits mapping all of these different perspectives on the system onto a single common substrate. This services substrate is readily represented diagramatically, thus making details of the overall design much more accessible.

Shames, Peter↗
DOE OSTI2024

Data for Optimizing Bioenergy Sorghum Productivity and Nutrient Removal in Illinois: Impact of Nitrogen Fertilization Under Diverse Marginal Conditions

Bioenergy sorghum ( Sorghum bicolor L. Moench) is a promising crop for contributing to the United States bioenergy supply. However, the varying limitations of the marginal lands targeted for its cultivation present a management challenge. This two-year study aimed to investigate how the limitations associated with marginal cropland impact the effects of nitrogen fertilization on the yield of bioenergy sorghum and the uptake of 11 macro- (N, P, K, Ca, Mg, and S) and micronutrients (Fe, Mn, Zn, Cu, and B). The study contrasted prime cropland in central Illinois (Urbana) with three marginal cropland sites in southern (Ewing) and central Illinois (Fairbury and Pesotum). These marginal cropland sites are characterized by varying limitations, including low soil fertility (P and K limitations), leaching and erosion, and flooding, respectively. Four nitrogen rates (0, 56, 112, and 168 kg N ha−1) were tested under eight environments. The average yields and ranges of sorghum biomass were 20.2 (17.0–23.2) Mg ha−1 in Urbana, 18.1 (13.1–19.8) Mg ha−1 in Ewing, 13.8 (9.0–17.3) Mg ha−1 in Fairbury, and 23.3 (14.6–33.0) Mg ha−1 in Pesotum. Optimal N rates were 56 N in Pesotum and 112 N in Urbana, Ewing, and Fairbury. Tissue macronutrient contents in Urbana were generally higher than in the marginal croplands, while micronutrient contents did not show discernible trends. Increasing N rate generally correlated with the macronutrient removal except in Ewing. Comparable sorghum biomass yields were observed between prime and marginal croplands (averaging 18.3 Mg ha−1), but optimal N rates varied between 56 N and 112 N. This suggests that yield gaps can be narrowed by applying the optimal N rates for the respective locations. However, increased removals of macronutrients, especially P and K, with increasing yields indicate the need to revise fertilizer recommendations, particularly for soils deficient in these nutrients. Our study suggests that while sorghum production on marginal cropland is feasible, N management needs to be adapted to the unique limitations associated with various types of marginal cropland.

Biomass Analytics↗
NASA NTRS1987

The effects of inlet turbulence and rotor/stator interactions on the aerodynamics and heat transfer of a large-scale rotating turbine model. Part 4: Aerodynamic data tabulation

A combined experimental and analytical program was conducted to examine the effects of inlet turbulence and airfoil heat transfer. The experimental portion of the study was conducted in a large-scale (approx. 5X engine), ambient temperature, rotating turbine model configured in both single-stage and stage-and-a-half arrangements. Heat transfer measurements were obtained using low-conductivity airfoils with miniature thermocouples welded to a thin, electrically heated surface skin. Heat transfer data were acquired for various combinations of low or high inlet turbulence intensity, flow coefficient, first stator-rotor axial spacing, Reynolds number and relative circumferential position of the first and second stators. Aerodynamic measurements obtained include distributions of the mean and fluctuating velocities at the turbine inlet and, for each airfoil row, midspan airfoil surface pressures and circumferential distributions of the downstream steady state pressures and fluctuating velocities. Results include airfoil heat transfer predictions produced using existing 2-D boundary layer computation schemes and an examination of solutions of the unsteady boundary layer equations.

Dring, R. P.↗