Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AUGMENTATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Advanced augmentor-wing research

Results of research on advanced augmentors are discussed. Research concerned with performance indicated that: (1) augmentors with lobe-type nozzles give higher thrust augmentation than those with slot-type primary nozzles; (2) the thrust of augmentor wings at forward speed is greater than that of internally blown flaps for the speed range of interest; and (3) the optimum augmentor geometry at forward speed may be different from the optimum static geometry. Analysis of augmentor-wing data shows that the data may be correlated by accounting for the augmentation and entrainment in defining a net thrust coefficient.

Aiken, T. N.↗
NASA NTRS1973

Suppression of flutter

An active aerodynamic control system to control flutter over a large range of oscillatory frequencies is described. The system is not affected by mass, stiffness, elastic axis, or center of gravity location of the system, mode of vibration, or Mach number. The system consists of one or more pairs of leading edge and trailing edge hinged or deformable control surfaces, each pair operated in concert by a stability augmentation system. Torsion and bending motions are sensed and converted by the stability augmentation system into leading and trailing edge control surface deflections which produce lift forces and pitching moments to suppress flutter.

Nissim, E.↗
NASA NTRS1973

Summary of stability and control characteristics of the XB-70 airplane

The stability and control characteristics of the XB-70 airplane were evaluated for Mach numbers up to 3.0 and altitudes up to 21,300 meters (70,000 feet). The airplane's inherent longitudinal characteristics proved to be generally satisfactory. In the lateral-directional modes, the airplane was characterized by light wheel forces, low static directional stability beyond approximately 2 deg of sideslip, adverse yaw response to aileron inputs throughout the entire Mach number range, and negative effective dihedral with wingtips full down. At subsonic Mach numbers, with the flight augmentation control system off, the light wheel forces and adverse yaw response to aileron inputs caused the pilots to minimize use of the ailerons. At supersonic Mach numbers, with the augmentation system off, the adverse yaw due to aileron and the negative effective dihedral were conducive to pilot-induced oscillations.

Wolowicz, C. H.↗
NASA NTRS1972

Advanced augmentor-wing research

Results of research on advanced augmentors are discussed. Research concerned with performance has indicated that: (1) augmentors with lobe-type nozzles give higher thrust augmentation than those with slot-type primary nozzles, (2) the thrust of augmentor wings at forward speed is greater than that of internally blown flaps for the speed range of interest, and (3) the optimum augmentor geometry at forward speed may be different from the optimum static geometry. Analysis of augmentor-wing data has shown that the data may be correlated by accounting for the augmentation and entrainment in defining a net thrust coefficient.

Aiken, T. N.↗
NASA NTRS1972

Simulator evaluation of the flying qualities of externally blown flap and augmentor wing transport configurations

Concurrent simulations of powered-lift STOL transport aircraft having either an externally blown flap configuration or an augmentor wing configuration were conducted. The following types of simulators of varying sophistication were used: (1) a simple fixed-base simulation with a simple visual display, (2) a more complex fixed-base simulation using a realistic transport cockpit and a high-quality visual display, and (3) a six-degree-of-freedom motion simulator that had a realistic transport cockpit and a sophisticated visual display. The unaugmented flying qualities determined from these simulations were rated as unacceptable for both the externally blown flap and augmentor wing configurations. The longitudinal, lateral-directional, and single-engine-failure characteristics were rated satisfactory with extensive augmentation, including pitch and roll command systems, flight-path (or speed) augmentation, turn coordination, and effective yaw damping. However, the flare and landing characteristics from any approach glide-path angle in excess of 4 deg were rated as unsatisfactory but acceptable.

Kier, D. A.↗
NASA NTRS1973

Wind tunnel investigation of a large-scale upper surface blown-flap transport model having two engines

An investigation has been conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an upper surface blowing flap system that would augment lift. The model had a 25 deg swept wing of aspect ratio 7.89 and two turbofan engines with the engine centerline located at 0.256 of the wing semispan. The lift of the flap system was augmented by turbofan exhaust impingement on the Coanda surface. Results were obtained for several flap deflections and engine nozzle configurations at jet momentum coefficients from 0 to 4.0. Three-component longitudinal data are presented with two engines operating. Limited longitudinal and lateral data are presented with an engine out. In addition, limited exhaust and flap pressure data are presented.

Aoyagi, K.↗
NASA NTRS1973

Study of control system effectiveness in alleviating vortex wake upsets.

The problem of an airplane being upset by encountering the vortex wake of a large transport on takeoff or landing is currently receiving considerable attention. This paper describes the technique and results of a study to assess the effectiveness of automatic control systems in alleviating vortex wake upsets. A six-degree-of-freedom nonlinear digital simulation was used for this purpose. The analysis included establishing the disturbance input due to penetrating a vortex wake from an arbitrary position and angle. Simulations were computed for both a general aviation airplane and a commercial jet transport. Dynamic responses were obtained for the penetrating aircraft with no augmentation and with various command augmentation systems. The results of this preliminary study indicate that it is feasible to use an automatic control system to alleviate vortex encounter upsets.

Johnson, W. A.↗
NASA NTRS1973

Experimental study on optimization parameters of a supersonic jet ejector thrust augmentor.

The experimental data were aimed at obtaining the effect of jet mixing, the effective length/diameter of the ejector tube, the entrance length shape factor, the shape loading, and the optimum primary jet location. The total augmented thrust is proportional to the diameter of the ejector. The data show that for a practical design the entrance lip shape and the stream lines around the lip are also important in order to optimize the percentage augmentation.

Cheng, D. Y.↗
NASA NTRS1973

Aerodynamic and noise measurements on a quasi-two dimensional augmentor wing model with lobe-type nozzles

An investigation was made of the static, wind-on aerodynamic and static noise characteristics of an augmentor wing having lobe type nozzles. The study was made in the Ames 7-by 10-Foot No. 1 Wind Tunnel using a small-scale, quasi-two-dimensional model. Several configurations of lobe nozzles as well as a normal slot nozzle were tested. Results indicate that lobe nozzles offer improved static and wind-on aerodynamics and reduced static noise relative to slot nozzles. Best wind-on performance was obtained when the tertiary gap was closed even though the static thrust augmentation was maximum with the gap open. Static thrust augmentation, wind-on lift and drag, and static noise directivity are presented as well as typical static and wind-on exit velocity profiles, surface pressure distributions and noise spectrums. The data are presented with limited discussion.

Aiken, T. N.↗
NASA NTRS1974

HFL-10 lifting body flight control system characteristics and operational experience

A flight evaluation was made of the mechanical hydraulic flight control system and the electrohydraulic stability augmentation system installed in the HL-10 lifting body research vehicle. Flight tests performed in the speed range from landing to a Mach number of 1.86 and the altitude range from 697 meters (2300 feet) to 27,550 meters (90,300 feet) were supplemented by ground tests to identify and correct structural resonance and limit-cycle problems. Severe limit-cycle and control sensitivity problems were encountered during the first flight. Stability augmentation system structural resonance electronic filters were modified to correct the limit-cycle problem. Several changes were made to control stick gearing to solve the control sensitivity problem. Satisfactory controllability was achieved by using a nonlinear system. A limit-cycle problem due to hydraulic fluid contamination was encountered during the first powered flight, but the problem did not recur after preflight operations were improved.

Painter, W. D.↗
NASA NTRS1974

Filament winding S-glass/polyimide resin composite processing studies

The work performed in selecting a TRW A-type polyimide resin that would be suitable for fabrication of filament wound reinforced plastic structures is described. Several different formulations were evaluated after which the P105AC formulation was selected as the most promising. Procedures then were developed for preparing P105AC/S-glass roving prepreg and for fabricating filament wound structural composites. Composites were fabricated and then tested in order to obtain tensile and shear strength information. Small, closed-end cylindrical pressure vessels then were fabricated using a stainless steel liner and end fittings with a P105AC/S-glass polar wound overwrap. These pressure vessels were cured in an air circulating oven without augmented pressure. It is concluded that the P105AC resin system is suitable for filament winding; that low void content, high strength composites are obtained by the filament winding process; and that augmented pressure is not required to effect the fabrication of filament wound P105AC composites.

Vaughan, R. W.↗
NASA NTRS1973

Space shuttle heat pipe thermal control systems

Heat pipe (HP) thermal control systems designed for possible space shuttle applications were built and tested under this program. They are: (1) a HP augmented cold rail, (2) a HP/phase change material (PCM) modular heat sink and (3) a HP radiating panel for compartment temperature control. The HP augmented cold rail is similar to a standard two-passage fluid cold rail except that it contains an integral, centrally located HP throughout its length. The central HP core helps to increase the local power density capability by spreading concentrated heat inputs over the entire rail. The HP/PCM modular heat sink system consists of a diode HP connected in series to a standard HP that has a PCM canister attached to its mid-section. It is designed to connect a heat source to a structural heat sink during normal operation, and to automatically decouple from it and sink to the PCM whenever structural temperatures are too high. The HP radiating panel is designed to conductively couple the panel feeder HPs directly to a fluid line that serves as a source of waste heat. It is a simple strap-on type of system that requires no internal or external line modifications to distribute the heat to a large radiating area.

Alario, J.↗
NASA NTRS1974

A predictive pilot model for STOL aircraft landing

An optimal control approach has been used to model pilot performance during STOL flare and landing. The model is used to predict pilot landing performance for three STOL configurations, each having a different level of automatic control augmentation. Model predictions are compared with flight simulator data. It is concluded that the model can be effective design tool for studying analytically the effects of display modifications, different stability augmentation systems, and proposed changes in the landing area geometry.

Kleinman, D. L.↗
NASA NTRS1974

Aerodynamic and acoustic performance of ejectors for engine-under-the-wing concepts

Subsonic thrust augmentation, exhaust plume velocity contours and acoustic characteristics of a small-scale, 6-tube mixer nozzle with ejector were obtained with and without a wing. Thrust augmentation up to 30 percent was achieved. Aerodynamic results showed that at a given location, greater downstream velocities are obtained with an ejector than with the baseline nozzle. Ejectors reduce high frequency noise; however, low frequency noise amplification also occurs. Acoustic reflections off the wing increase the noise level to a ground observer. With an ejector, the acoustic benefits of forward velocity may be significantly reduced compared with the baseline nozzle.

Vonglahn, U.↗
NASA NTRS1974

Advanced supersonic technology propulsion system study

This study had the objectives of determining the most promising conventional and variable cycle engine types; the effect of design cruise Mach number (2.2, 2.7 and 3.2) on a commercial supersonic transport; effect of advanced engine technology on the choice of engine cycle; and effect of utilizing hydrogen as the engine fuel. The technology required for the engines was defined, and the levels of development to ensure availability of this technology in advanced aircraft propulsion systems were assessed. No clearcut best conventional or variable cycle engine was identified. The dry bypass turbojet and the duct burning turbofans were initially selected as the best conventional engines, but later results, utilizing augmentation at takeoff, added the mixed-flow augmented turbofan as a promising contender. The modulating air flow, three-rotor variable cycle engine identified the performance features desired from VCE concepts (elimination of inlet drag and reduction in afterbody drag), but was a very heavy and complex engine.

Szeliga, R.↗
NASA NTRS1974

TRW A-type polyimide resin for filament winding

Studies were conducted to select a TRW A-type polyimide resin that would be suitable for fabrication of filament wound reinforced plastics structures. Several different formulations were evaluated after which the P105AC formulation was selected as the most promising. Procedures were developed for preparing P105AC/S-glass roving prepreg and for fabricating filament wound structural composites. Composites were fabricated and then tested in order to obtain tensile and shear strength information. Small, closed-end cylindrical pressure vessels then were fabricated using a stainless steel liner and end-fittings with a P105AC/S-glass polar-wound overwrap. These pressure vessels were cured in an air circulating oven without augmented pressure. It was concluded upon completion of this study that the P105AC resin system is suitable for filament winding; that low void content, high strength composites are obtained by the filament winding process; and that augmented pressure is not required to effect the fabrication of filament wound P105AC composites.

Vaughan, R. W.↗
NASA NTRS1974

Aerodynamic and acoustic performance of ejectors for engine-under-the-wing concepts

Subsonic thrust augmentation, exhaust plume velocity contours and acoustic characteristics of a small-scale, 6-tube mixer nozzle with ejector were obtained with and without a wing. Thrust augmentation up to 30 percent was achieved. Aerodynamic results showed that at a given location, greater downstream velocities are obtained with an ejector than with the baseline nozzle. Ejectors reduce high frequency noise; however, low-frequency noise amplification also occurs. Acoustic reflections off the wing increase the noise level to a ground observer. With an ejector, the acoustic benefits of forward velocity may be significantly reduced compared with the baseline nozzle.

Von Glahn, U.↗
NASA NTRS1974

Aerodynamics of jet flap and rotating cylinder flap STOL concepts

The aerodynamic effectiveness of various propulsive lift concepts to provide for the low speed performance and control required for short takeoff and landing aircraft is discussed. The importance of the interrelationship between the propulsion system and aerodynamic components of the aircraft is stressed. The relative effectiveness of different lift concepts was evaluated through static and wind tunnel tests of various aerodynamic models and propulsion components, simulations of aircraft, and in some cases, flight testing of research aircraft incorporating the concepts under study. Results of large scale tests of lift augmentation devices are presented. The results of flight tests of STOL research aircraft with augmented jet flaps and rotating cylinder flaps are presented to show the steeper approach flight paths at low forward speeds.

Cook, W. L.↗