Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Characterization of hydrogen-plasma interactions with photoresist, silicon, and silicon nitride surfaces

For the 45 nm technology node and beyond, a major challenge is to achieve reasonably high photoresist ash rates while minimizing the loss of the silicon (Si) substrate and its nitride (Si{sub 3}N{sub 4}). Accordingly, an objective of this work is to characterize the photoresist strip rate under varying conditions of H{sub 2} plasma and the effects of these conditions on Si and Si{sub 3}N{sub 4} etch rates. In addition, we discuss in detail the fundamental mechanisms of the reactions between H atoms and the above substrates and successfully reconcile the process trends obtained with the reaction mechanisms. In this work, photoresist, Si, and Si{sub 3}N{sub 4} films were exposed to downstream pure-H{sub 2} discharges and their removal rates were characterized by ellipsometry as a function of the following parameters: substrate temperature, reactor pressure, H{sub 2} flow rate, and source power. The authors found that the H{sub 2}-based dry ash and Si{sub 3}N{sub 4} etch are both thermally activated reactions, evidenced by the steady increase in etch rate as a function of temperature, with activation energies of {approx}5.0 and {approx}2.7 kcal/mol, respectively. The Si substrate exhibits a rather unique behavior where the etch rate increases initially to a maximum, which occurs at {approx}40 deg. C, and then decreases upon a further increase in temperature. The decrease in the Si etch rate at higher temperatures is attributed to the activation of competing side reactions that consume the chemisorbed H atoms on the Si surface, which then suppresses the Si-etch step. The photoresist and Si{sub 3}N{sub 4} removal rates increase initially with increasing pressure, reaching maxima at {approx}800 and 2000 mTorr, respectively, beyond which the removal rates drop with increasing pressure. The initial increase in removal rate at the low-pressure regime is attributed to the increased atomic-hydrogen density, whereas the decrease in ash rate at the high-pressure regime could be attributed to the recombination of H atoms that could occur by various mechanisms. At temperatures where the reaction rates are relatively fast, the photoresist and Si removal rates both increase continuously with the H{sub 2} flow rate, indicating that both reactions are in the supply-limited regime. For the range of process conditions explored here, we find that the etch rates of Si are generally much higher than those for Si{sub 3}N{sub 4} with Si:Si{sub 3}N{sub 4} etch-rate ratios that vary from 25 to >>520. Based on the process trends obtained here, we have identified a process window--high temperature and intermediate pressure--that attains relatively high photoresist ash rates and low Si and Si{sub 3}N{sub 4} etch rates.

36 MATERIALS SCIENCE↗

Characterization of Atomic and Electronic Structures of Electrochemically Active SOFC Cathode Surfaces

The objective of this project is to gain a fundamental understanding of the oxygen-reduction mechanism on mixed conducting cathode materials by means of quantum-chemical calculations coupled with direct experimental measurements, such as vibrational spectroscopy. We have made progress in the elucidation of the mechanisms of oxygen reduction of perovkite-type cathode materials for SOFCs using these quantum chemical calculations. We established computational framework for predicting properties such as oxygen diffusivity and reaction rate constants for adsorption, incorporation, and TPB reactions, and formulated predictions for LSM- and LSC-based cathode materials. We have also further developed Raman spectroscopy as well as SERS as a characterization tool for SOFC cathode materials. Raman spectroscopy was used to detect chemical changes in the cathode from operation conditions, and SERS was used to probe for pertinent adsorbed species in oxygen reduction. However, much work on the subject of unraveling oxygen reduction for SOFC cathodes remains to be done.

30 DIRECT ENERGY CONVERSION↗

Earthquake detection in a simulated lunar regolith using distributed acoustic sensing

Current models of inner lunar geology have largely been inferred from the seismic experiments and observations performed during the Apollo missions that comprised a relatively small number of seismic instruments. Refining constraints on fundamental lunar relationships such as crust-mantle and mantle-core boundaries in the future will require seismic arrays spanning larger epicentral distances. A promising technology for installing dense seismic arrays with minimal human effort is distributed acoustic sensing (DAS), an approach that allows a single length of fiber optic cable to act as hundreds or thousands of sensors when coupled with a DAS interrogator. While terrestrial uses of DAS technology for seismic monitoring rely on burying the cable to maximize fidelity of seismic signal transmission to the fiber, digging meters of trench to bury optical fiber on lunar or planetary surfaces is logistically infeasible. To evaluate DAS signal attenuation due to surface deployment of cable in lunar regolith, we completed earthquake detection analyses that evaluated the sensitivity of an optic-fiber DAS system to seismic signals at different burial depths. We deployed a single-mode fiber in a 10-m open-bottom wooden box filled with a lunar regolith simulant (LRS) with fiber buried at different depths within the LRS and recorded signals for four regional and local earthquakes. The results were used to identify and evaluate signal attenuation in surface-deployed fiber compared to buried fiber in the LRS. Burial depth responses to active-source signals were also evaluated similar to previous studies characterizing DAS sensitivity of surface-deployed fiber. Atmospheric noise was minimal as the cable was deployed in an indoor environment; however, where observed, atmospheric and anthropogenic noise was filtered out using the same bandpass filtering used to identify earthquake events. We found that signal attenuation of the surface-deployed fiber compared to buried fiber was relatively high in active-source experiments but was not consistently observed in earthquake signals. That burial depth is not highly correlated to attenuation of the observed earthquake signals indicates that in a noise-limited environment, placing DAS-interrogated fiber directly at the regolith surface may be a promising deployment strategy to consider for sensing remote seismic signals during lunar exploration.

58 GEOSCIENCES↗

Influence of copper and aluminum substitution on high-temperature oxidation of the FeCoCrNiMn “Cantor” alloy

In this study, the oxidation behavior of FeCoCrNiMn (HEA + Mn) is compared to three modified HEAs manufactured by substituting Mn with Al, Cu, or Al + Cu. Oxidation tests were conducted between 600°C and 800°C for up to 500 h in synthetic air. Substitution of Mn leads to a significant improvement in the oxidation resistance for the three modified HEAs. For FeCoCrNiCu (HEA + Cu), a local attack of a Cu-rich phase was observed, leading to the formation of CuO blisters on the surface. The FeCoCrNiAl (HEA + Al) alloy was characterized by the formation of a thin Al 2 O 3 surface layer for all temperatures. However, for the HEA + Al alloy the formation of AlN was observed after 300 h at 800°C, leading to a partial breakdown of the protective scale. FeCoCrNiCuAl (HEA + Cu + Al) by far showed the best oxidation resistance, characterized by the formation of a highly protective Al 2 O 3 scale that effectively inhibited nitrogen penetration into the metal subsurface and local attack of the Cu-rich phase.

36 MATERIALS SCIENCE↗

Laser Powder Bed Fusion Additive Manufacture Nb1Zr Development

Next generation fission and fusion nuclear reactors require materials that can withstand operating temperatures greater than 500 °C, neutron irradiation doses of up to 200 displacements per atom (dpa), and potentially corrosive coolants such as the alkali liquid metals sodium, lithium, and NaK (Na33K eutectic alloy). Refractory alloys, such as Nb1Zr (Nb-1wt%Zr) and Molybdenum alloy TZM (Mo-0.5wt%Ti-0.08wt%Zr) have been traditionally considered viable candidates for advanced fission and fusion reactor concepts. However, it is relatively difficult to generate complex geometries of interest from these alloys using traditional manufacturing methods. In addition, there needs to be a concentrated effort to address refractory metal challenges at elevated temperature operation. In order to generate complex geometries of interest, modern manufacturing techniques are considered to increase the technological readiness level (TRL), cost-effectiveness, and schedule savings. This work focused on the continued development of laser powder bed fusion (L-PBF) additive manufacturing (AM) to improve both design flexibility, evaluate microstructure and properties, and ultimately accelerate the TRL and qualification of these processes and alloys for components to potentially be put into service. Niobium alloy Nb1Zr was identified through a down-selection process outlined in previous reports as a candidate to develop in L-PBF AM. Historically, Nb1Zr had been explored for high temperature fast spectrum fission reactors for both terrestrial and space applications. Molybdenum alloy TZM has also been considered for these reactor concepts due to exceptional high-temperature strength, creep resistance, and stability under irradiation. L-PBF AM of TZM has previously been investigated at LANL under the Microreactor program, NASA, ORNL, and in academia. However, due to the crack prone nature of TZM, L-PBF AM of TZM resulted in significant microcracking and additional development is required to pursue viable maturation. Other AM methods have been found to be more successful in printing TZM, and those alternatives approaches are discussed in this effort. The efforts detailed in this report focused on continued development of Nb1Zr through L-PBF and development of TZM via L-PBF and electron powder bed fusion (E-PBF). The objective of this work was to further the development of these AM techniques for the chosen refractory alloys, elucidating and addressing associated challenges through characterization of several demonstration builds. At LANL, Nb1Zr builds were completed using an EOS M290 and M400 machines, and a refractory alloy-dedicated L-PBF system, the Xact Metal XM200G, was installed. The XM200G primary purpose was to do the Nb1Zr parameter development process; however, due to difficulties associated with the machine installation and qualification process, it was decided to pivot development to the larger M400 and M290 machines. Although the supply of Nb1Zr powder was limited, it was sufficient to generate sub-scale metallographic specimens for the purpose of parameter development. This was first accomplished on the EOS M400 then the M290 due to machine schedule availability. Further development of TZM has been initiated at the University of Texas El Paso (UTEP) under contract with LANL to use both a heated build envelope L-PBF machine and E-PBF machine that have been found in the literature to mitigate microcracking. UTEP was provided with TZM powder and build plates to support parallel TZM parameter development across both machines. As part of the contract, UTEP will also be conducting microstructural characterization once optimized process parameters have been identified. The optimized process parameters for each machine will be used to generate a series of metallographic, mechanical, and surface finish specimens for subsequent characterization and testing. In the next section, we provide a detailed discussion of the methodology used for investigating the feasibility of leveraging these alloys for use in advanced reactor applications.

36 MATERIALS SCIENCE↗

Nanoengineered field induced charge separation membranes and methods of manufacture thereof

A device according to one embodiment includes a porous membrane having a surface charge and pore configuration characterized by a double layer overlap effect being present in pores of the membrane. A device according to another embodiment includes a porous membrane having a surface charge in pores thereof sufficient to impart anion or cation selectivity in the pores. Additional devices, systems and methods are also presented.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Evaluation of Bentonite Engineered Barrier Performance under Repository Conditions

Nuclear energy has been an important source of power throughout the world for several decades, but with that power comes substantial amounts of waste. The USA alone is projected to produce 77,100 MTHM (34,700 MCi) of commercial spent fuel by the year 2020. There has been a growing sense of urgency to determine a method of disposal for all types of nuclear waste. Underground storage has been proposed as the safest means of long term storage and disposal by both the Academy of Sciences and the Blue Ribbon Commission with a focus on deep geologic disposal. Because deep geological repositories (DGR) pose as the safest method of disposal due to the isolation of the waste and the low-permeability of the surrounding material, it is crucial to understand the science behind these repositories. Many scientists have concern with DGRs because of all the unanswered scientific questions. With a global inventory of 300,000 MTHM, it is imperative to understand how DGRs will retain the nuclear waste over a time span of up to a projected 1 million years. Because of the amount of nuclear waste increases each year, there is an inherent need to study the viability of a repository in order to begin implementation of that repository. Based on the half-lives of each radionuclide in nuclear waste, after approximately 100 years of storage, the heat production from the decay of radionuclides becomes dominated by the long-lived actinides. Because the decay of the nuclear waste results in an elevated temperature within the canister, That mixed with water intrusion can corrode the canister and allow radionuclides to leach into the surrounding environment. In an effort to retain these radionuclides within the repositories, most all deep geologic repository designs incorporate an engineered multi-barrier approach. Once the radionuclides begin to leach out of the canisters, the next barrier to retain them is a layer of compacted clay such as a smectite. A mechanistic understanding of mobility at elevated temperatures is crucial in order to evaluate the performance of the engineered clay barrier system within a deep geological repository. Because the clay barrier is compacted so tightly, the only method of mobility for radionuclides is through molecular diffusion. Assessing the factors that affect the rates at which various radionuclides will diffuse through these clays is important in the performance assessment of the repository system as a whole. Neptunium-237 has been identified as a major actinide of concern for long term storage, dominating the radioactivity emitted from the waste between 10,000 to 100,000 years of storage. Under oxidizing conditions, this radionuclide exists mainly as Np(V). In this oxidation state, the neptunium exists chemically as the NpO{sub 2}{sup +} ion which exhibits enhanced mobility characteristics such as high solubility and low affinity for sorption to surfaces. Because of this, {sup 237}Np(V) has been identified as the most mobile radionuclide in nuclear waste and thus a major radionuclide of concern, motivating research into the mobility of {sup 237}Np(V) through the compacted clay barrier. Bentonite is one of the most common backfill materials used in repositories. This clayey rock's main constituent is the mineral Na-montmorillonite [(Ca{sub 0.06}Na{sub 0.14}K{sub 0.05})(Al{sub 1.57}Fe{sup 3+} {sub 0.17}Mg{sub 0.25})(Al{sub 0.04}Si{sub 3.96}O{sub 10} - (OH){sub 2})] which gives this material the advantageous properties required for a repository such as a high swelling capacity. Because of this high affinity for absorbing water, montmorillonite is the ideal candidate for backfill material in a deep geological repository. Adsorption of radionuclides onto the surface of the compacted clay is a major mechanism for retardation of mobility. Because diffusion and adsorption are integrated into this process, it is important to characterize Np adsorption onto the surface of compacted montmorillonite. Previous studies have quantified the adsorption of Np onto montmorillonite at variable ionic strengths and temperatures. Furthermore, several studies have focused on the diffusion of Np through compacted clay, but no other studies have determined diffusion coefficients at elevated temperatures of up to 80 deg. C. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Predicting Surface Clustering at Ambient Conditions from Thermodynamic Data

Scanning tunneling microscopy (STM) has proved to be a prime tool to characterize the atomic structure of crystal surfaces under UHV conditions. With the development of high-pressure scanning tunneling microscopy (HP-STM), the scope of this technique has been largely extended, as new structures were found to occur under gas phase chemical potentials achieved under ambient conditions. Particularly interesting is the substantial restructuring of initially flat and stable surfaces into new orientations by formation of nanoclusters. Here we discuss the possible generality of this phenomenon by analyzing cases where atomically flat surfaces of certain transition metals undergo such changes in the presence of CO at room temperature (RT) while some remain unchanged. From our analysis we argue that such changes can be predicted from thermodynamic data published in the literature, particularly from the difference in adsorption energy on low-and high-coordination sites, like terrace and step sites, which can be obtained from thermal desorption spectroscopy (TDS) measurements, and possibly also from theoretical calculations. Finally, for the vicinal surfaces with high Miller indices, changes in the repulsive elastic interactions between the ordered steps due to adsorbates may also play an important role.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Silicon Solid Electrolyte Interphase (SEI) of Lithium Ion Battery Characterized by Microscopy and Spectroscopy

The surface reactions of electrolytes with a silicon anode in lithium ion cells have been investigated. The investigation utilizes two novel techniques that are enabled by the use of binder-free silicon (BF-Si) nanoparticle anodes. The first method, transmission electron microscopy with energy dispersive X-ray spectroscopy, allows straightforward analysis of the BF-Si solid electrolyte interphase (SEI). The second method utilizes multi-nuclear magnetic resonance spectroscopy of D2O extracts from the cycled anodes. The TEM and NMR data are complemented by XPS and FTIR data, which are routinely used for SEI studies. Coin cells (BF-Si/Li) were cycled in electrolytes containing LiPF6 salt and ethylene carbonate or fluoroethylene carbonate solvent. Capacity retention was significantly better for cells cycled with LiPF6/FEC electrolyte than for cells cycled with LiPF6/EC electrolyte. Our unique combination of techniques establishes that for LiPF6/EC electrolyte the BF-Si SEI continuously grows during the first 20 cycles and the SEI becomes integrated with the BF-Si nanoparticles. The SEI predominantly contains lithium ethylene dicarbonate, LiF, and LixSiOy. BF-Si electrodes cycled with LiPF6/FEC electrolyte have a different behavior; the BF-Si nanoparticles remain relatively distinct from the SEI. The SEI predominantly contains LiF, LixSiOy, and an insoluble polymeric species.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Moessbauer Characterization of Magnetite/Polyaniline Magnetic Nanocomposite

Aniline surface coated Fe{sub 3}O{sub 4} nanoparticles have been successfully synthesized by UV irradiation varying the time and the acid media (HCl, HNO{sub 3}, or H{sub 2}SO{sub 4}). The synthesized material represents a promising platform for application in nerve regeneration. XRD patterns are consistent with the crystalline structure of magnetite. Nevertheless, for UV irradiation times longer than 2 h, extra XRD lines reveal the presence of goethite. The mean crystallite size of uncoated particles is estimated to be 25.4 nm, meanwhile that size is reduced to 19.9 nm for the UV irradiated sample in HCl medium for 4 h. Moessbauer spectra of uncoated nanoparticles reveal the occurrence of thermal relaxation at room temperature, while the 77 K-Moessbauer spectrum suggests the occurrence of electron localization effects similar to that expected in bulk magnetite. The Mossbauer spectra of UV irradiated sample in HCl medium during 4 h, confirms the presence of the goethite phase. For this sample, the thermal relaxation is more evident, since the room temperature spectrum shows larger spectral area for the nonmagnetic component due to the smaller crystallite size. Meanwhile, the 77 K-Moessbauer spectrum suggests the absence of the electron localization effect above 77 K.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Development of New Experimental Methods for Correlated Operando Surface/Gas Characterization

The predictive understanding of catalytic surface reactions requires accurate microkinetic models, and while decades of work has been devoted to the elucidation of the reaction steps in these models, many open questions remain. One key issue is a lack of approaches enabling the local spatially resolved assessment of catalytic activity over a surface. In this report, we detail efforts to develop a new diagnostic approach to solve this problem. The approach is based upon laser resonance enhanced multiphoton ionization of reaction products emitted into the gas phase followed by spatially resolved imaging of the resultant ions or electrons. Ion imaging is pursued with a velocity-selected spatially resolved ion imaging microscope, while electron imaging was attempted in a low energy electron microscope. Successful demonstration of the ion imaging microscope coupled with the development of transport simulations shows promise for a revolutionary new tool to assess local catalytic activity

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Designing Antifouling and Antimicrobial Interfaces: Structural Characterization using CryoEM, Automated Microscopy, and AI Image Segmentation

The design of functionalized surfaces for interactions with biological systems is critical across sectors such as healthcare, energy, and agriculture. Tailoring materials for specific applications, such as antifouling and antimicrobial surfaces, demands a comprehensive understanding of topology and chemistry across multiple length and time scales on both biological and materials systems. This work presents the development and characterization of nanostructured surfaces with controlled topographies and chemistries that enhance bacterial membrane disruption, reduce biofilm formation, and improve antimicrobial and antifouling capabilities. Two specific use cases will be presented - the use of cellulose nanocrystals (CNCs) for bacterial growth inhibition and the development of antifouling surfaces to prevent protein and bacterial adsorption [1-4]. By leveraging large language models (LLMs) for image segmentation and training [5], we enable automated analysis of terabyte-scale cryogenic electron microscopy (cryoEM) datasets. This analysis provides statistical insights into the biotic/abiotic interface and facilitates automated electron microscopy experiments to mitigate time and dose. The integration of cryogenic electron tomography (cryoET) and cryogenic focused ion beam (cryoFIB) milling enables high-resolution, near-native-state imaging and 3D reconstructions of bio/material interfaces [6]. Orthogonal characterization techniques and computational modeling further enhances our understanding, offering a robust platform for the design and optimization of next-generation functional surfaces [7].

Williams, Alexis [ORNL] (ORCID:0000000252835822)↗

Nanoscale imaging of alteration layers of corroded international simple glass particles using ToF-SIMS

Glass particles with dimensions typically ranging from tens to hundreds of microns are often used in glass corrosion research in order to accelerate testing. Two-dimensional and three-dimensional nanoscale imaging techniques are badly needed to characterize the alteration layers at the surfaces of these corroded glass particles. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) can provide a lateral resolution as low as ~100 nm, and, compared to other imaging techniques, is sensitive to elements lighter than carbon. In this work, we used ToF-SIMS to characterize the alteration layers of corroded international simple glass (ISG) particles. At most particle surfaces, inhomogeneous or no alteration layers were observed, indicating that the thickness of the alterations layers may be too thin to be observable by ToF-SIMS imaging. Relatively thick (e.g., 1-10 microns) alteration layers were inhomogeneously distributed at a small portion of surfaces. More interestingly, some large-size (tens of microns) glass particles were fully altered. Above observations suggest that weak attachment and the defects on ISG particle surfaces play an important role in ISG glass corrosion.

alteration layer↗

Nanostructured Magnetic Materials (Final Technical Progress Report)

This report describes progress made during the final phase of our DOE-funded program on Nanostructured Magnetic Materials. This period was quite productive, resulting in the submission of three papers and presentation of three talks at international conferences and three seminars at research institutions. Our DOE-funded research efforts were directed toward studies of magnetism at surfaces and interfaces in high-quality, well-characterized materials prepared by Molecular Beam Epitaxy (MBE) and sputtering. We have an exceptionally well-equipped laboratory for these studies, with: Thin film preparation equipment; Characterization equipment; Equipment to study magnetic properties of surfaces and ultra-thin magnetic films and interfaces in multi-layers and superlattices.

36 MATERIALS SCIENCE↗

Surface roughness scattering of electrons in bulk mosfets

Surface-roughness scattering of electrons at the Si-SiO 2 interface is a very important consideration when analyzing Si metal-oxide-semiconductor field-effect transistors (MOSFETs). Scattering reduces the mobility of the electrons and degrades the device performance. 250-nm and 50-nm bulk MOSFETs were simulated with varying device parameters and mesh sizes in order to compare the effects of surface-roughness scattering in multiple devices. The simulation framework includes the ensemble Monte Carlo method used to solve the Boltzmann transport equation coupled with a successive over-relaxation method used to solve the two-dimensional Poisson's equation. Four methods for simulating the surface-roughness scattering of electrons were implemented on both devices and compared: the constant specularity parameter, the momentum-dependent specularity parameter, and the real-space-roughness method with both uniform and varying electric fields. The specularity parameter is the probability of an electron scattering speculariy from a rough surface. It can be chosen as a constant, characterizing partially diffuse scattering of all electrons from the surface the same way, or it can be momentum dependent, where the size of rms roughness and the normal component of the electron wave number determine the probability of electron-momentum randomization. The real-space rough surface method uses the rms roughness height and correlation length of an actual MOSFET to simulate a rough interface. Due to their charge, electrons scatter from the electric field and not directly from the surface. If the electric field is kept uniform, the electrons do not perceive the roughness and scatter as if from a at surface. However, if the field is allowed to vary, the electrons scatter from the varying electric field as they would in a MOSFET. These methods were implemented for both the 50-nm and 250-nm MOSFETs, and using the rms roughness heights and correlation lengths for real devices. The current-voltage and mobility-electric field curves were plotted for each method on the two devices and compared. The conclusion is that the specularity-parameter methods are valuable as simple models for relatively smooth interfaces. However, they have limitations, as they cannot accurately describe the drastic reduction in the current and the electron mobility that occur in MOSFETs with very rough Si-SiO 2 interfaces.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Coming Closer to High Frequency Gravitational Wave Detection With MAGO

In the last years, low frequency gravitational waves (GWs) have been consistently measured by the LIGOVirgo collaboration, but little to no attention has been paid to higher frequencies GWs in the range of 10 kHz to 100 MHz, at which confirmation for current theories or even new physics could be hidden. The MAGO 2.0 project aims at filling this gap in the parameter space using superconducting radio-frequency (SRF) cavities. Exploiting the excellent Q-factors of these resonators, we plan to detect tiny harmonic deformations induced by GWs which change the boundary conditions of the oscillating electromagnetic field. We present the results of the first cold tests ran at DESY and FNAL using the cavity prototype built 20 years ago at the end of the MAGO collaboration, characterizing the RF spectrum, Q-factor and surface resistance. Additionally we introduce the mechanical vibration spectrum characterization and the RF response of the cavity with the injection of a “fake GW” signal using piezoelectric actuators.

Marconato, Giovanni [Hamburg U.]↗

Behavior of Au Species in Au/Fe 2 O 3 Catalysts Characterized by Novel In Situ Heating Techniques and Aberration-Corrected STEM Imaging

The recent advent of a novel design of in situ heating technology for electron microscopes has permitted unprecedented control of elevated temperature studies of catalytic materials, particularly when coupled with the sub- ngstr m imaging performance of a modern aberration-corrected scanning transmission electron microscope (STEM). In using micro-electro-mechanical-systems (MEMS)-based Aduro heating chips from Protochips, Inc. (Raleigh, NC, USA) it allows nearly instantaneous heating and cooling of catalyst powders, while avoiding the effects of temperature ramping as experienced with standard heating stages. The heating technology also provides stable operation limited only by the inherent drift in the microscope stage, thus allowing full image resolution to be achieved even at elevated temperatures. Our study details the use of both the high X-Y spatial resolution in both dark-field and simultaneous bright-field imaging, along with the high resolution in Z (depth sectioning) provided by the large probe incidence semiangle in the aberration-corrected instrument, to characterize the evolution of microstructure in a commercial Au/Fe 2 O 3 water-gas shift catalyst during elevated temperature treatment. The phenomenon of Au diffusion to the surface of hematite support particles to form discrete crystalline Au nanoparticles in the 1-2 nm size range, after a prior leaching treatment to remove surface Au species has been characterized.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Flow pattern and void fraction characterization in nitrogen/water flows through a diamond-type triply periodic minimal surface lattice

Here, this study presents, to the authors knowledge, the first experimental investigation on the void fraction and flow patterns in two-phase flows through a diamond-type Triply Periodic Minimal Surface (TPMS) lattice. An additively manufactured TPMS structure was tested under upward co-current flow of a water/nitrogen mixture. Superficial velocities varied for a total of 42 test conditions (gas: 0.01–2.4 m/s; liquid: 0.01–2.4 m/s; mass flux: 20–2370 kg/m 2 ·s). High-speed video and X-ray imaging enabled time-averaged void fraction measurements and identified six distinct flow regimes which were used to develop a flow pattern map. Comparison of the void fraction data with correlations from literature demonstrated the Rouhani and Axelsson (1970) [49] correlation modified by Steiner (1993) [52] provided the best agreement, which was improved with empirically fit coefficients. This approach predicted the void fraction with errors < ±20% for 64% of the data, with a mean absolute percent deviation (MAPD) of 23%. The measured frictional pressure drop was compared to correlations from literature which captured the observed trends but did not provide good accuracy. The best agreement was found after optimizing the empirical coefficients of the Muller-Steinhagen & Heck (1986) [56] correlation; this approach captured 33% of the data within ±20% with a MAPD of 46% over the full range and captured 71% of the data within ±20% a MAPD of 13.3% at mass fluxes >1100 kg/m 2 -s. These results provide foundational insight into TPMS two-phase flow behavior and inform modeling and design of advanced heat exchange components incorporating TPMS geometries.

42 - ENGINEERING↗