Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “functional performance testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Graphical method for predicting life of a rocket thrust chamber with half-hard zirconium-copper liner and electroformed nickel closeout

A method for estimating the life of a regeneratively cooled rocket thrust chamber was developed and is based on the hot-gas wall temperature and the temperature difference between the hot-gas wall and the outside surface of the closeout. This method permits a quick estimate of the life of a thrust chamber when design changes or test-cycle variations are considered. Strain range and life are presented graphically as functions of these temperature parameters for a typical high-performance rocket thrust chamber with a half-hard zirconium-copper liner and an electroformed nickel closeout.

Kasper, H. J.↗
NASA NTRS1978

Automated solar-cell-array assembly machine

Continuous-feeding machine automatically bonds solar cells to printed-circuit substrate. In completed machine, cells move to test station where electrical characteristics could be checked. If performance of cell is below specifications, that cell is marked and removed. All machine functions are synchronized by electronics located within unit. It may help to lower costs in future solar-cell production.

Costogue, E. N.↗
NASA NTRS1978

Continuous Czochralski Growth. Silicon Sheet Growth Development of the Large Area Silicon Sheet Task of the Low Cost Silicon Solar Array Project

The JPL Continuous Czochralski Growth Facility is now essentially complete and is functional. In this reporting period, a silicon lump recharging device was designed, and a prototype was built which performed well in simulated recharge tests. The large chamber (designed to accommodate a 14-inch hot zone) was put into operation initially with the standard hot zone in order to compare performance with previous experience. Some modifications were made to the hot zones in the larger chamber due to considerably larger radiative heat losses. Several short (one-ingot) runs were performed and four continuous runs were attempted. The largest continuous run lasted 64 hours and produced 57 kilograms of ingot.

Merz, F.↗
NASA NTRS1977

Non-parametric PCM to ADM conversion

An all-digital technique to convert pulse code modulated (PCM) signals into adaptive delta modulation (ADM) format is presented. The converter developed is shown to be independent of the statistical parameters of the encoded signal and can be constructed with only standard digital hardware. The structure of the converter is simple enough to be fabricated on a large scale integrated circuit where the advantages of reliability and cost can be optimized. A concise evaluation of this PCM to ADM translation technique is presented and several converters are simulated on a digital computer. A family of performance curves is given which displays the signal-to-noise ratio for sinusoidal test signals subjected to the conversion process, as a function of input signal power for several ratios of ADM rate to Nyquist rate.

Locicero, J. L.↗
NASA NTRS1980

Characterization of silicon-gate CMOS/SOS integrated circuits processed with ion implantation

The double layer metallization technology applied on p type silicon gate CMOS/SOS integrated circuits is described. A smooth metal surface was obtained by using the 2% Si-sputtered Al. More than 10% probe yield was achieved on solar cell controller circuit TCS136 (or MSFC-SC101). Reliability tests were performed on 15 arrays at 150 C. Only three arrays failed during the burn in, and 18 arrays out of 22 functioning arrays maintained the leakage current below 100 milli-A. Analysis indicates that this technology will be a viable process if the metal short circuit problem between the two metals can be reduced.

Woo, D. S.↗
NASA NTRS1981

Evaluation of the Williams-type model for barley yields in North Dakota and Minnesota

The Williams-type yield model is based on multiple regression analysis of historial time series data at CRD level pooled to regional level (groups of similar CRDs). Basic variables considered in the analysis include USDA yield, monthly mean temperature, monthly precipitation, soil texture and topographic information, and variables derived from these. Technologic trend is represented by piecewise linear and/or quadratic functions of year. Indicators of yield reliability obtained from a ten-year bootstrap test (1970-1979) demonstrate that biases are small and performance based on root mean square appears to be acceptable for the intended AgRISTARS large area applications. The model is objective, adequate, timely, simple, and not costly. It consideres scientific knowledge on a broad scale but not in detail, and does not provide a good current measure of modeled yield reliability.

Barnett, T. L.↗
NASA NTRS1981

Evaluation of the CEAS model for barley yields in North Dakota and Minnesota

The CEAS yield model is based upon multiple regression analysis at the CRD and state levels. For the historical time series, yield is regressed on a set of variables derived from monthly mean temperature and monthly precipitation. Technological trend is represented by piecewise linear and/or quadriatic functions of year. Indicators of yield reliability obtained from a ten-year bootstrap test (1970-79) demonstrated that biases are small and performance as indicated by the root mean square errors are acceptable for intended application, however, model response for individual years particularly unusual years, is not very reliable and shows some large errors. The model is objective, adequate, timely, simple and not costly. It considers scientific knowledge on a broad scale but not in detail, and does not provide a good current measure of modeled yield reliability.

Barnett, T. L.↗
NASA NTRS1984

Development of dynamic simulation of TF34-GE-100 turbofan engine with post-stall capability

This paper describes the development of a hybrid computer simulation of a TF34-GE-100 turbofan engine with post-stall capability. The simulation operates in real-time and will be used to test and evaluate stall recovery control modes for this engine. The simulation calculations are performed by an analog computer with a peripheral multivariable function generation unit used for computing bivariate functions. Tabular listings of a simulation variables are obtained by interfacing to a digital computer and using a custom software package for data collection and display.

Krosel, S. M.↗
NASA NTRS1984

Development of dynamic simulation of TF34-GE-100 turbofan engine with post-stall capability

This paper describes the development of a hybrid computer simulation of a TF34-GE-100 turbofan engine with post-stall capability. The simulation operates in real-time and will be used to test and evaluate stall recovery control modes for this engine. The simulation calculations are performed by an analog computer with a peripheral multivariable function generation unit used for computing bivariate functions. Tabular listings of simulation variables are obtained by interfacing to a digital computer and using a custom software package for data collection and display.

Krosel, S. M.↗
NASA NTRS1985

Development of an Organic Rankine-Cycle power module for a small community solar thermal power experiment

An organic Rankine-cycle (ORC) power module was developed for use in a multimodule solar power plant to be built and operated in a small community. Many successful components and subsystems, including the reciever, power conversion subsystem, energy transport subsystem, and control subsystem, were tested. Tests were performed on a complete power module using a test bed concentrator in place of the proposed concentrator. All major single-module program functional objectives were met and the multimodule operation presented no apparent problems. The hermetically sealed, self-contained, ORC power conversion unit subsequently successfully completed a 300-hour endurance run with no evidence of wear or operating problems.

Kiceniuk, T.↗
NASA NTRS1985

Systems approach to software fault tolerance

Computing systems are employed for aerospace applications with high reliability requirements. In order to provide the needed reliability, it was necessary to make use of computing systems with fault-tolerance characteristics. Traditionally, fault tolerance is achieved through the use of hardware redundance. However, fault-tolerant techniques based on suitable software design considerations have also been developed. The present paper is concerned with the major issues arising in the context of an application of fault-tolerant software techniques to dynamic systems. Attention is given to fault-tolerant flight software, software component stability, system stability with fault-tolerant software, the preservation of functional performance, N-version vs. recovery blocks in flight software, systems-based software, static and dynamic models, static and dynamic consistency tests, and recovery block initialization.

Caglayan, A. K.↗
NASA NTRS1986

Real-time simulator for helicopter rotor wind-tunnel operations

This paper describes the elements and operation of a simulator that is being used to train operators of the Rotor Test Apparatus (RTA) in the large-scale 40- by 80-Foot Wind Tunnel at Ames Research Center. The simulator, named TUTOR (for Tunnel Utilization Trainer with Operating Rotor) duplicates the controls of the rotor and its dynamic behavior, as well as the wind-tunnel controls. The simulation software uses a preexisting blade-element model of a four-bladed rotor with flapping and lead-lag degrees of freedom. Equations were developed for all hardware and controls of the RTA and of the wind tunnel that are normally required to perform a wind-tunnel test of a helicopter rotor. The simulator hardware consists of consoles designed to have the same appearance and functions as those in the control room of the 40- by 80-Foot Wind Tunnel, allowing input from three operators who normally establish the required operating conditions during a test run. Normal operating procedures can be practiced, as well as simulated emergencies such as rotor power failure.

Talbot, P. D.↗
NASA NTRS1987

Full-scale thrust reverser testing in an altitude facility

A two-dimensional convergent-divergent exhaust nozzle designed and fabricated by Pratt and Whitney Aircraft was installed on a PW1128 turbofan engine and tested during thrust reverser operation in an altitude facility at NASA Lewis Research Center. A unique collection system was used to capture the thrust reverser exhaust gas and transport it to the primary exhaust collector. Tests were conducted at three flight conditions with varying amounts of thrust reverse at each condition. Some reverser exhaust gas spillage by the collection system was encountered but engine performance was unaffected at all flight conditions tested. Based on the results of this test program, the feasibility of altitude testing of advanced multi-function exhaust nozzle systems has been demonstrated.

Mehalic, Charles M.↗
NASA NTRS1991

Probabilistic methods for rotordynamics analysis

This paper summarizes the development of the methods and a computer program to compute the probability of instability of dynamic systems that can be represented by a system of second-order ordinary linear differential equations. Two instability criteria based upon the eigenvalues or Routh-Hurwitz test functions are investigated. Computational methods based on a fast probability integration concept and an efficient adaptive importance sampling method are proposed to perform efficient probabilistic analysis. A numerical example is provided to demonstrate the methods.

Wu, Y.-T.↗
NASA NTRS1991

Validation of an expert system intended for research in distributed artificial intelligence

The expert system discussed in this paper is designed to function as a testbed for research on cooperating expert systems. Cooperating expert systems are members of an organization which dictates the manner in which the expert systems will interact when solving a problem. The Blackbox Expert described in this paper has been constructed using the C Language Integrated Production System (CLIPS), C++, and X windowing environment. CLIPS is embedded in a C++ program which provides objects that are used to maintain the state of the Blackbox puzzle. These objects are accessed by CLIPS rules through user-defined functions calls. The performance of the Blackbox Expert is validated by experimentation. A group of people are asked to solve a set of test cases for the Blackbox puzzle. A metric has been devised which evaluates the 'correctness' of a solution proposed for a test case of Blackbox. Using this metric and the solutions proposed by the humans, each person receives a rating for their ability to solve the Blackbox puzzle. The Blackbox Expert solves the same set of test cases and is assigned a rating for its ability. Then the rating obtained by the Blackbox Expert is compared with the ratings of the people, thus establishing the skill level of our expert system.

Grossner, C.↗
NASA NTRS1996

Development of a Wafer Positioning System for the Sandia Extreme Ultraviolet Lithography Tool

A wafer positioning system was recently developed by Sandia National Laboratories for an Extreme Ultraviolet Lithography (EUVL) tool. The system, which utilizes a magnetically levitated fine stage to provide ultra-precise positioning in all six degrees of freedom, incorporates technological improvements resulting from four years of prototype development. This paper describes the design, implementation, and functional capability of the system. Specifics regarding control system electronics, including software and control algorithm structure, as well as performance design goals and test results are presented. Potential system enhancements, some of which are in process, are also discussed.

Wronosky, John B.↗
NASA NTRS1998

EOS/AMSU: A Blackbody Spacecraft Test Targets Operation and Maintenance Manual

This report describes the spacecraft test targets and readout console as described in section 5.3.3 of the performance specification S-480-80. The spacecraft targets are to be used to provide a well-known radiometric reference for testing the functionality of the AMSU-A instruments at the spacecraft contractor's facility.

Source record↗
NASA NTRS2005

SQL-RAMS

SQL-RAMS (where "SQL" signifies Structured Query Language and "RAMS" signifies Rocketdyne Automated Management System) is a successor to the legacy version of RAMS a computer program used to manage all work, nonconformance, corrective action, and configuration management on rocket engines and ground support equipment at Stennis Space Center. The legacy version resided in the FileMaker Pro software system and was constructed in modules that could act as stand-alone programs. There was little or no integration among modules. Because of limitations on file-management capabilities in FileMaker Pro, and because of difficulty of integration of FileMaker Pro with other software systems for exchange of data using such industry standards as SQL, the legacy version of RAMS proved to be limited, and working to circumvent its limitations too time-consuming. In contrast, SQL-RAMS is an integrated SQL-server-based program that supports all data-exchange software industry standards. Whereas in the legacy version, it was necessary to access individual modules to gain insight to a particular work-status documents, SQL-RAMS provides access through a single-screen presentation of core modules. In addition, SQL-RAMS enable rapid and efficient filtering of displayed statuses by predefined categories and test numbers. SQL-RAMS is rich in functionality and encompasses significant improvements over the legacy system. It provides users the ability to perform many tasks which in the past required administrator intervention. Additionally many of the design limitations have been corrected allowing for a robust application that is user centric.

Alfaro, Victor O.↗