Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “feature engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Revolutionary Vertical Lift Technology Lift + Cruise Concept Vehicle Powertrain Dynamic Model

The Lift + Cruise (L+C) is one of several Revolutionary Vertical Lift Technology (RVLT) concept aircraft identified by NASA to investigate Urban Air Mobility (UAM) requirements. This six-passenger vehicle has a conventional tube-and-wing configuration, but with eight lift rotors (four on each wing) and a pusher rotor on the tail. This arrangement allows it to take off and land vertically as well as fly like an airplane. This report presents a novel dynamic model of the L+C powertrain built using the Toolbox for the Modeling and Analysis of Thermodynamic Systems (T-MATS) and the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), both of which are NASA-developed toolboxes, and together are capable of modeling hybrid-electric powertrain architectures. This research effort models the complex behavior of the powertrain at the mechanical timescale (15 to 20 ms). The model consists of a turboshaft engine, generator, direct current bus, energy storage management system, gearboxes, and electric propulsor systems coupled together to create a dynamic model that mimics the operation of the multidomain powertrain. Two control algorithms, designed to equalize the power consumed to the power produced, are compared to assess their practicality: (1) independent proportional-integral (PI) control and (2) linear quadratic integral regulator (LQIR) control. Simulation results highlight the key features present in the model and demonstrate its operation under the two control schemes.

revolutionary vertical lift technology↗
NASA NTRS1970

Elastohydrodynamic lubrication

The history of this relatively new topic in tribology is presented, and attention is drawn to the significant theoretical and experimental developments. The position of elastohydrodynamics in the spectrum of lubrication regimes is discussed, and the essential features of elastohydrodynamic contacts are described. Attention is focused upon film thickness calculations and measurements since this represents one of the most important and best charted fields within the subject, but friction and the distribution of pressure are also considered. Transition from hydrodynamic to elastohydrodynamic and boundary lubrication conditions is considered, and attention is drawn to the importance of the ratio of film thickness/surface roughness. A number of successful engineering applications of elastohydrodynamics are noted, and the present trends in research are outlined.

Dowson, D.↗
NASA NTRS2000

Analytical and Computational Aspects of Collaborative Optimization

Bilevel problem formulations have received considerable attention as an approach to multidisciplinary optimization in engineering. We examine the analytical and computational properties of one such approach, collaborative optimization. The resulting system-level optimization problems suffer from inherent computational difficulties due to the bilevel nature of the method. Most notably, it is impossible to characterize and hence identify solutions of the system-level problems because the standard first-order conditions for solutions of constrained optimization problems do not hold. The analytical features of the system-level problem make it difficult to apply conventional nonlinear programming algorithms. Simple examples illustrate the analysis and the algorithmic consequences for optimization methods. We conclude with additional observations on the practical implications of the analytical and computational properties of collaborative optimization.

Alexandrov, Natalia M.↗
NASA NTRS2007

Smart Payload Development for High Data Rate Instrument Systems

This slide presentation reviews the development of smart payloads instruments systems with high data rates. On-board computation has become a bottleneck for advanced science instrument and engineering capabilities. In order to improve the computation capability on board, smart payloads have been proposed. A smart payload is a Localized instrument, that can offload the flight processor of extensive computing cycles, simplify the interfaces, and minimize the dependency of the instrument on the flight system. This has been proposed for the Mars mission, Mars Atmospheric Trace Molecule Spectroscopy (MATMOS). The design of this system is discussed; the features of the Virtex-4, are discussed, and the technical approach is reviewed. The proposed Hybrid Field Programmable Gate Array (FPGA) technology has been shown to deliver breakthrough performance by tightly coupling hardware and software. Smart Payload designs for instruments such as MATMOS can meet science data return requirements with more competitive use of available on-board resources and can provide algorithm acceleration in hardware leading to implementation of better (more advanced) algorithms in on-board systems for improved science data return

Virtex-4↗
NASA NTRS2019

Progress Towards Modeling the Mars Science Laboratory PICA-NuSil Heatshield

The data collected by the Mars Science Laboratory (MSL) Entry, Descent and Landing Instrumentation, MEDLI, have become an established reference to assess the performance of engineering models of the Phenolic Impregnated Carbon Ablator (PICA) and to validate hypersonic computational fluid dynamics (CFD) tools for entry systems. MEDLI measurements are also extensively used as validation reference for current developments of high-fidelity material response models for PICA. So large has been the scientific output and impact of MEDLI that a follow-up instrumentation suite MEDLI2 is underway for the upcoming Mars 2020 mission.A feature neglected thus far in the modeling of the MSL heatshield, is the presence of a silicone-based room temperature vulcanizing coating designated NuSil CV-1144-0. NuSil was used to coat the entire MSL heatshield, including the MEDLI plugs, to mitigate the spread of phenolic dust from PICA, and limit contamination during clean room operations. NuSil CV-1144-0 is a space grade siloxane copolymer, designed as an oxygen protection barrier for extreme low temperature environment.Assessments conducted during MSL development demonstrated that the presence of NuSil had no adverse effect on the performance of PICA. However, evidence from ground testing of PICA-NuSil (PICA-N) models in the HyMETS arc-jet test facility suggests that the silicone changes the high temperature response of PICA. It is therefore critical to assess the importance of modeling the coating in ongoing code validation efforts.

Bessire, Brody K.↗
NASA NTRSDate not supplied

Distributed Thrust Takeoff for the NASA X-57 Mod IV Flight Demonstrator

The Mod IV configuration of the X-57 flight demonstrator concept featured two forms of distributed electric propulsion—one cruise propulsor at each wingtip for primary propulsion that enabled favorable interaction with the wingtip vortex, and six high-lift propulsors distributed along the leading edge of each wing to enhance low-speed flight characteristics. The power system that fed these propulsors was arranged in two independent power buses. This unique arrangement did not lend itself to traditional “one engine inoperative” methods for determining performance after a critical failure in the propulsion system. Several potential failure scenarios were identified as potential “critical loss of thrust” events, and experiments that included pilot-in-the-loop simulation with the project test pilots were conducted to determine if these events would result in adequate handling and performance. Prior research showed that a total failure of one of the cruise motors during takeoff or initial climb could result in unacceptable performance for a traditional full-power takeoff. A new technique dubbed Distributed Thrust Takeoff (DiTTo) was developed to reduce the impact of the thrust asymmetry and total loss of thrust that could occur in any of the critical loss of thrust scenarios. The results showed that adequate performance and handling qualities could be achieved in each of the critical failure scenarios when using the DiTTo technique.

Distributed Propulsion, Electric Propulsion, Criti↗
NASA NTRSDate not supplied

Distributed Thrust Takeoff for the NASA X-57 Mod IV Flight Demonstrator

The Mod IV configuration of the X-57 flight demonstrator concept featured two forms of distributed electric propulsion—one cruise propulsor at each wingtip for primary propulsion that enabled favorable interaction with the wingtip vortex, and six high-lift propulsors distributed along the leading edge of each wing to enhance low-speed flight characteristics. The power system that fed these propulsors was arranged in two independent power buses. This unique arrangement did not lend itself to traditional “one engine inoperative” methods for determining performance after a critical failure in the propulsion system. Several potential failure scenarios were identified as potential “critical loss of thrust” events, and experiments that included pilot-in-the-loop simulation with the project test pilots were conducted to determine if these events would result in adequate handling and performance. Prior research showed that a total failure of one of the cruise motors during takeoff or initial climb could result in unacceptable performance for a traditional full-power takeoff. A new technique dubbed Distributed Thrust Takeoff (DiTTo) was developed to reduce the impact of the thrust asymmetry and total loss of thrust that could occur in any of the critical loss of thrust scenarios. The results showed that adequate performance and handling qualities could be achieved in each of the critical failure scenarios when using the DiTTo technique.

Distributed Propulsion↗
NASA NTRS2006

Letting The NASA Press Engine Work For You

You have an amazing result based on NASA data or a NASA Mission; you have written your seminal paper and submitted it to your favorite journal. You believe it has press potential and maybe you've even gotten help from your PR folks in writing a press release. Now you would really like NASA to issue this as a press release. But how do you do that? This presentation will illustrate the steps required to engage NASA in helping promote your story. What are NASA's requirements for newsworthiness? Should your news be released as a web feature story or in the local media? Does your news rise to the level of a full-blown press conference or will it be a media teleconference? How do you obtain approval for a NASA press event? Once your result is scheduled to be issued as a press release, how can you improve your chances of getting the best possible coverage for your story? I will discuss the NASA press process and suggest how to consider factors like timing, working with your collaborating institutions in an efficient way, and not letting the cat out of the bag until the press event.

Weaver, Kimberly↗
NASA NTRS1985

Cryogenic propellant management: Integration of design, performance and operational requirements

The integration of the design features of the Shuttle elements into a cryogenic propellant management system is described. The implementation and verification of the design/operational changes resulting from design deficiencies and/or element incompatibilities encountered subsequent to the critical design reviews are emphasized. Major topics include: subsystem designs to provide liquid oxygen (LO2) tank pressure stabilization, LO2 facility vent for ice prevention, liquid hydrogen (LH2) feedline high point bleed, pogo suppression on the Space Shuttle Main Engine (SSME), LO2 low level cutoff, Orbiter/engine propellant dump, and LO2 main feedline helium injection for geyser prevention.

Worlund, A. L.↗
NASA NTRS1999

High-Energy Space Propulsion Based on Magnetized Target Fusion

A conceptual study is made to explore the feasibility of applying magnetized target fusion (MTF) to space propulsion for omniplanetary travel. Plasma-jet driven MTF not only is highly amenable to space propulsion, but also has a number of very attractive features for this application: 1) The pulsed fusion scheme provides in situ a very dense hydrogenous liner capable of moderating the neutrons, converting more than 97% of the neutron energy into charged particle energy of the fusion plasma available for propulsion. 2) The fusion yield per pulse can be maintained at an attractively low level (< 1 GJ) despite a respectable gain in excess of 70. A compact, low-weight engine is the result. An engine with a jet power of 25 GW, a thrust of 66 kN, and a specific impulse of 77,000 s, can be achieved with an overall engine mass of about 41 metric tons, with a specific power density of 605 kW/kg, and a specific thrust density of 1.6 N/kg. The engine is rep-rated at 40 Hz to provide this power and thrust level. At a practical rep-rate limit of 200 Hz, the engine can deliver 128 GW jet power and 340 kN of thrust, at specific power and thrust density of 1,141 kW/kg and 3 N/kg respectively. 3) It is possible to operate the magnetic nozzle as a magnetic flux compression generator in this scheme, while attaining a high nozzle efficiency of 80% in converting the spherically radial momentum of the fusion plasma to an axial impulse. 4) A small fraction of the electrical energy generated from the flux compression is used directly to recharge the capacitor bank and other energy storage equipment, without the use of a highvoltage DC power supply. A separate electrical generator is not necessary. 5) Due to the simplicity of the electrical circuit and the components, involving mainly inductors, capacitors, and plasma guns, which are connected directly to each other without any intermediate equipment, a high rep-rate (with a maximum of 200 Hz) appears practicable. 6) All fusion related components are within the current state of the art for pulsed power technology. Experimental facilities with the required pulsed power capabilities already exist. 7) The scheme does not require prefabricated fuel target and liner hardware in any esoteric form or state. All necessary fuel and liner material are introduced into the engine in the form of ordinary matter in gaseous state at room temperature, greatly simplifying their handling on board. They are delivered into the fusion reaction chamber in a completely standoff manner.

Thio, Y. C. F.↗
NASA NTRS2000

A Flight Training Simulator for Instructing the Helicopter Autorotation Maneuver (Enhanced Version)

Autorotation is a maneuver that permits a safe helicopter landing when the engine loses power. A catastrophe may occur if the pilot's control inputs are incorrect, insufficient, excessive, or poorly timed. Due to the danger involved, full-touchdown autorotations are very rarely practiced. Because in-flight autorotation training is risky, time-consuming, and expensive, the objective of the project was to develop the first helicopter flight simulator expressly designed to train students in this critical maneuver. A central feature of the project was the inclusion of an enhanced version of the Pilot-Rotorcraft Intelligent Symbology Management Simulator (PRISMS), a virtual-reality system developed by Anacapa Sciences and Thought Wave. A task analysis was performed to identify the procedural steps in the autorotation, to inventory the information needed to support student task performance, to identify typical errors, and to structure the simulator's practice environment. The system provides immediate knowledge of results, extensive practice of perceptual-motor skills, part-task training, and augmented cueing in a realistic cockpit environment. Additional work, described in this report, extended the capabilities of the simulator in three areas: 1. Incorporation of visual training aids to assist the student in learning the proper appearance of the visual scene when the maneuver is being properly performed; 2. Introduction of the requirement to land at a particular spot, as opposed to the wide, flat open field initially used, and development of appropriate metrics of success; and 3. Inclusion of wind speed and wind direction settings (and random variability settings) to add a more realistic challenge in "hitting the spot."

Rogers, Steven P.↗
NASA NTRSDate not supplied

Understanding the Durability of SiC Based Ceramic Matrix Composites (CMCs) for Gas Turbine Engine Hot Section Components

Silicon carbide fiber reinforced silicon carbide ceramic matrix composites (SiCf/SiC-CMCs) are being used in the fabrication of gas turbine engine hot section components due to their light weight and excellent thermal and chemical stabilities at high-temperature. These superior properties enable significant enhancements in engine efficiency and reduced fuel burn, emissions, and cooling requirements. In support of NASA’s Aeronautics Mission under various programs at Glenn Research Center, different types of composites have been developed and assessed for a high temperature (2700 °F) SiCf/SiC CMC system for turbine engine applications. These composites have creep-resistant SiC fibers, advanced 3D weaves, 2700 °F-capable hybrid SiC matrices, and durable environmental barrier coatings (EBCs). These efforts have resulted in improvements in the overall CMC thermomechanical and environmental durability. In order to study the role of different constituents and processing variables, a single fiber tow CVI (chemical vapor infiltration) SiC/SiC mini-composite can be considered the basic architectural feature of woven and laminate SiC/SiC CMCs. Moreover, the mini-composite mechanical and tensile creep damage behavior represents the creep behavior of 0° fiber tows in the axial loading direction of a macro-composite or component. In addition, a large number of mini-composite samples can be fabricated at relatively low cost within a short time, which makes them attractive for obtaining a robust set of experimental data and studying constituent behavior. In this presentation, the mini-composite approach to study damage mechanisms that limit CMC life in extreme environments including exposure to steam will be presented. The effects of constituent type and volume fraction on the CMC durability, which will help influence CMC design, will be discussed.

Ceramic Matrix Composites (CMCs)↗
NASA NTRS2023

New Retropropulsion Concept with NTAC Power for Mars Entry

Since the initial deployments of probes, orbiters, and rovers on Mars, there have been many ideas and concepts on how to perform an entry, descent, and landing (EDL) process efficiently and safely through the Martian atmosphere to place payloads onto the surface of Mars. Among the missions sent to perform EDL on Mars, only roughly sixty percent of the missions have been successful. The 5 minutes to 20 minutes of communication gap due to long-range telecommunications to Earth, described as seven minutes of terror, add to the complexity of EDL missions to Mars. As the payloads have become larger, the method of EDL has become more complex. To place an automobile-size science rover on the Martian surface requires the use of retrorockets mounted on a Sky Crane during the final subsonic stage of EDL. Larger payloads will require more propellant and more and/or larger retropropulsion engines during the earlier supersonic stage of EDL. The Sky Crane concept may not be scalable for these larger payloads and during supersonic flight; hence, new approaches are sought. A new power technology invented at NASA called Nuclear Thermionic Avalanche Cell (NTAC) may offer an additional solution. Powered by NTAC, the newly invented retropropulsion concept would ingest carbon dioxide gas, heat it up and blast it out as a new feature of the EDL process. NTAC would be reusable as a primary power source for payloads such as excavators, three-dimensional (3D) printers, or mobile equipment for mining, construction, and additive manufacturing tasks. Since NTAC would need to be landed with its host payload or as a standalone power package, assessing its ability to assist in its own EDL seems reasonable. The purpose of this Technical Memorandum (TM) is to examine the performance of NTAC in the context of EDL at Mars for motivating studies for integrating NTAC into future Mars mission architectures.

Mars entry↗
NASA NTRS1978

Application of advanced high speed turboprop technology to future civil short-haul transport aircraft design

With an overall goal of defining the needs and requirements for short-haul transport aircraft research and development, the objective of this paper is to determine the performance and noise impact of short-haul transport aircraft designed with an advanced turboprop propulsion system. This propulsion system features high-speed propellers that have more blades and reduced diameters. Aircraft are designed for short and medium field lengths; mission block fuel and direct operating costs (DOC) are used as performance measures. The propeller diameter was optimized to minimize DOC. Two methods are employed to estimate the weight of the acoustic treatment needed to reduce interior noise to an acceptable level. Results show decreasing gross weight, block fuel, DOC, engine size, and optimum propfan diameter with increasing field length. The choice of acoustic treatment method has a significant effect on the aircraft design.

Conlon, J. A.↗
NASA NTRS1986

Development of a numerical procedure to map a general 3-d body onto a near-circle

Conformal mapping is a classical technique utilized for solving problems in aerodynamics and hydrodynamics. Conformal mapping is utilized in the construction of grids around airfoils, engine inlets and other aircraft configurations. These shapes are transformed onto a near-circle image for which the equations of fluid motion are discretized on the mapped plane and solved numerically by utilizing the appropriate techniques. In comparison to other grid-generation techniques such as algerbraic or differential type, conformal mapping offers an analytical and accurate form even if the grid deformation is large. One of the most appealing features is that the grid can be constrained to remain orthogonal to the body after the transformation. Hence, the grid is suitable for analyzing the supersonic flow past a blunt object. The associated shock as a coordinate surface adjusts its position in the course of computation until convergence is reached. The present work applied conformal mapping to 3-D bodies with no axis of symmetry such as the Aerobraking Flight Experiment (AFE) vehicle, transforming the AFE shape onto a near-circle image. A numerical procedure and code are used to generate grids around the AFE body.

Hommel, M. J.↗
NASA NTRS1986

Fiber-reinforced superalloy composites provide an added performance edge

Fiber reinforcements are being explored as a means to increasing the performance of superalloys past 980 C. Fiber-reinforced superalloys (FRS), particularly tungsten FRS (TFRS) are candidate materials for rocket-engine turbopump blades for advanced Shuttle engines and in airbreathing and other rocket engines. Refractory metal wires are the reinforcement of choice due to tolerance to fiber/matrix interactions. W alloy fibers have a maximum tensile strength of 2165 MPa at 1095 C and a 100 hr creep rupture strength at stresses up to 1400 MPa. A TFRS has the potential of a service temperature 110 C over the strongest superalloy. Manufacturing processes being evaluated to realize the FRS components are summarized, together with design features which will be introduced in turbine blades to take advantage of the FRS materials and to extend their surface life.

Petrasek, D. W.↗
NASA NTRS1988

Liquid rocket booster integration study. Volume 1: Executive summary

The impacts of introducing liquid rocket booster engines (LRB) into the Space Transportation System (STS)/Kennedy Space Center (KSC) launch environment are identified and evaluated. Proposed ground systems configurations are presented along with a launch site requirements summary. Prelaunch processing scenarios are described and the required facility modifications and new facility requirements are analyzed. Flight vehicle design recommendations to enhance launch processing are discussed. Processing approaches to integrate LRB with existing STS launch operations are evaluated. The key features and significance of launch site transition to a new STS configuration in parallel with ongoing launch activities are enumerated. This volume is the executive summary of the five volume series.

Source record↗
NASA NTRS1988

Liquid Rocket Booster Integration Study. Volume 2: Study synopsis

The impacts of introducing liquid rocket booster engines (LRB) into the Space Transportation System (STS)/Kennedy Space Center (KSC) launch environment are identified and evaluated. Proposed ground systems configurations are presented along with a launch site requirements summary. Prelaunch processing scenarios are described and the required facility modifications and new facility requirements are analyzed. Flight vehicle design recommendations to enhance launch processing are discussed. Processing approaches to integrate LRB with existing STS launch operations are evaluated. The key features and significance of launch site transition to a new STS configuration in parallel with ongoing launch activities are enumerated. This volume is the study summary of the five volume series.

Source record↗