Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrolyte additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Polynomial Expressions for Estimating Elastic Constants From the Resonance of Circular Plates

Two approaches were taken to make convenient spread sheet calculations of elastic constants from resonance data and the tables in ASTM C1259 and E1876: polynomials were fit to the tables; and an automated spread sheet interpolation routine was generated. To compare the approaches, the resonant frequencies of circular plates made of glass, hardened maraging steel, alpha silicon carbide, silicon nitride, tungsten carbide, tape cast NiO-YSZ, and zinc selenide were measured. The elastic constants, as calculated via the polynomials and linear interpolation of the tabular data in ASTM C1259 and E1876, were found comparable for engineering purposes, with the differences typically being less than 0.5 percent. Calculation of additional v values at t/R between 0 and 0.2 would allow better curve fits. This is not necessary for common engineering purposes, however, it might benefit the testing of emerging thin structures such as fuel cell electrolytes, gas conversion membranes, and coatings when Poisson s ratio is less than 0.15 and high precision is needed.

Salem, Jonathan A.↗

Steady-State Pool Boiling in Sea Water

Boiling heat transfer has attracted broad attention because of its high efficiency of heat removal and many possible applications, such as nuclear safety issues. From the lessons learned from the Fukushima Daiichi accident in Japan in 2011, Taiwan Power Company proposed an 'Ultimate Response Guideline' to ensure that there is sufficient water which can be injected into the core and prevent the core from being uncovered. However, if the core uncovered accident really happens, one still needs to continuously inject water into the core to keep the situation from getting worse. This is so called the 'quenching process'. Usually, a nuclear power plant is located near the bank of river or coast, so it is easy to get river or sea water as water resources during an emergency condition. Sea and deionized water (DI water) show significantly different performance during the quenching process. Hsu et al. conducted quenching experiments using different metal spheres (stainless steel 304 and zircaloy 702) initially at 1000 deg. C in deionized water and sea water to compare their difference. Their results indicated that sea water demonstrates a more rapid quenching process due to the suppression of film boiling, the zeta-potential between the hot surface and sea water and other effects prevent the formation of the vapor blanket. Lee et al. also studied quenching process by a reflooding method. They reported the rapid quenching time in sea water is due to higher boiling point and easily top quenching by sea salt solution. Despite the fact that better quenching performance has been observed in sea water, more fundamental experiments must be carried out to investigate basic boiling phenomena in sea water. For the past few years, many researchers studied steady boiling behavior based on pool boiling experiments. The parameters that may affect heat transfer coefficient include nucleation site density, wettability, surface tension, etc. Jamialahmadi et al. selected sodium sulfate (high solubility in water) and calcium sulfate (low solubility in water) solution as testing liquids with rod heaters used. They discovered sparingly soluble salts with inversed solubility may deposit on the heating surface and block heat transfer to bulk liquid. However, the addition of highly soluble salts may reduce heat transfer coefficient at modest heat flux but increase slightly at high heat flux. A few years later, Jamialahmadi et al. suggested the decrease in heat transfer coefficient of electrolyte solution has to do with the mass transfer in the liquid phase and developed a model with high accuracy. For nuclear safety, the use of sea water as an alternative emergency coolant, more basic physical phenomena of boiling in sea water must be investigated. The present work conducts pool boiling of sea water by using a platinum wire and compares with that in deionized water.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Effects of fluorinated solvents on electrolyte solvation structures and electrode/electrolyte interphases for lithium metal batteries

Electrolyte is very critical to the performance of the high-voltage lithium (Li) metal battery (LMB), which is one of the most attractive candidates for the next generation high-density energy storage systems. Electrolyte formulation and structure determine the physical properties of the electrolytes and their interfacial chemistries on the electrode surfaces. Localized high-concentration electrolytes (LHCEs) outperform state-of-the-art carbonate electrolytes in many aspects in LMBs due to their unique solvation structure. Types of fluorinated co-solvents used in LHCEs are investigated here in searching for the most suitable diluent for high concentration electrolytes (HCEs). Non-solvating solvents (including fluorinated ethers, fluorinated borate and fluorinated orthoformate) added in HCEs enable the formation of LHCEs with high-concentration solvation structures. However, low solvating fluorinated carbonate will coordinate with Li+ ions and form a second solvation shell or a pseudo-LHCE which diminishes the benefits of LHCE. In addition, it is evident that the diluent has significant influence on the electrode/electrolyte interphases (EEIs) beyond retaining the high-concentration solvation structures. Diluent molecules surrounding the high-concentration clusters could accelerate or decelerate the anion decomposition through co-participation of diluent decomposition in the EEI formation. The varied interphase features lead to significantly different battery-performance. This study points out the importance of diluents and their synergetic effects with the conductive salt and the solvating solvent in designing LHCEs. These systematic comparisons and fundamental insights into LHCEs using different types of fluorinated solvents can guide further development of advanced electrolytes for high-voltage LMBs.

Cao, Xia↗

All-Solid-State Batteries Using Rationally Designed Garnet Electrolyte Frameworks

Functioning bulk-type all-solid-state batteries in a practical form factor with composite positive electrodes, using Al-substituted Li 7 La 3 Zr 2 O 12 (LLZO) as the solid electrolyte, have been demonstrated for the first time. The devices incorporate bilayers composed of dense LLZO membranes and porous LLZO scaffolds infiltrated with LiNi 0.6 Mn 0.2 Co 0.2 O 2 and other components as positive electrodes, combined with lithium anodes. The porous scaffolds are prepared using an easily scaled freeze-tape-casting method. The unidirectional pores of the scaffold facilitate infiltration of cathode components and shorten lithium ion diffusion path lengths, while the addition of a soft ionically conductive solid to the scaffold ensures good contact among the components.

25 ENERGY STORAGE↗

Synthesis and characterization of 2D molybdenum carbide (MXene)

Large scale synthesis and delamination of 2D Mo 2 CT x (where T is a surface termination group) has been achieved by selectively etching gallium from the recently discovered nanolaminated, ternary transition metal carbide Mo 2 Ga 2 C. Different synthesis and delamination routes result in different flake morphologies. The resistivity of free-standing Mo 2 CT x films increases by an order of magnitude as the temperature is reduced from 300 to 10 K, suggesting semiconductor-like behavior of this MXene, in contrast to Ti 3 C 2 T x which exhibits metallic behavior. At 10 K, the magnetoresistance is positive. Additionally, changes in electronic transport are observed upon annealing of the films. When 2 μm thick films are tested as electrodes in supercapacitors, capacitances as high as 700 F cm –3 in a 1 m sulfuric acid electrolyte and high capacity retention for at least 10,000 cycles at 10 A g –1 are obtained. Free-standing Mo 2 CT x films, with ≈8 wt% carbon nanotubes, perform well when tested as an electrode material for Li-ions, especially at high rates. In conclusion, at 20 and 131 C cycling rates, stable reversible capacities of 250 and 76 mAh g –1 , respectively, are achieved for over 1000 cycles.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Sulfonated Diels–Alder Poly(Phenylene)s in Membrane Electrode Assemblies for Fuel Cells

The transition to environmentally sustainable materials in fuel cells requires alternatives to persistent polyfluoroalkyl substances (PFAS) like Nafion. This study investigates the performance-limiting factors of membrane electrode assemblies (MEAs) utilizing sulfonated Diels–Alder poly(phenylene)s (sDAPPs) as PFAS-free polymer electrolytes. Among the configurations evaluated, the greatest performance loss occurred when sDAPP is used as the cathode binder, primarily due to phenyl group adsorption on catalyst surfaces, which reduces oxygen reduction reaction activity and impedes oxygen transport. Additional performance degradation arises from membrane-electrode interfacial incompatibility and insufficient ionomer hydrophobicity. By addressing ionomer adsorption and improving interfacial contact, an sDAPP-based cathode achieved a current density of 1.57 A cm −2 at 0.6 V under fully humidified H 2 /air conditions at 80 °C and 150 kPa abs . These results offer key insights for advancing high-performance, PFAS-free fuel cell technologies.

08 HYDROGEN↗

Anode‐Free Lithium–Sulfur Cells Enabled by Rationally Tuning Lithium Polysulfide Molecules

Abstract The two major barriers of practical lithium–sulfur batteries are the poor reversibility of lithium‐metal anode and sluggish kinetics of sulfur cathode. Here, we report a simple yet cogent, molecular tailoring approach for lithium polysulfides, enabling a synergistic enhancement of anode reversibility and cathode kinetics. We show that SnI 4 coordinates with lithium polysulfides to form soluble complexes, resulting in a Li 2 SnS 3 ‐rich anode interphase layer. As Li 2 SnS 3 is stable against parasitic reactions and has a lower ionic resistance over cycling, the Li plating/stripping efficiency is greatly improved. In addition, the formation of soluble complexes between SnI 4 and lithium polysulfides play a non‐negligible role in suppressing the clustering behavior of lithium polysulfide molecules, resulting in a significant enhancement in sulfur conversion kinetics under lean electrolyte conditions. The synergistic improvement is validated in anode‐free, lean‐electrolyte pouch cells with a Li 2 S cathode that displays capacity retention of 78 % after 100 cycles.

Ren, Yuxun↗

Electrochemical-driven green recovery of lithium, graphite and cathode from lithium-ion batteries using water

The expected exponential increase in consumption of lithium-ion batteries (LIBs) would pose a unique challenge to the availability of near-critical resources like lithium and graphite in the upcoming decade. In this work, we present a lithium recovery process that utilizes a degradation mechanism, i.e., lithium plating, as a tool to concentrate metallic lithium at the anode/separator interface for convenient extraction at room temperature – using only water. Electrochemical characterization of fast charged (1–6 C) LIBs yielded a maximum capacity fade of 50% over ten cycles. The lithium plating was confirmed via voltage plateau analysis, coulombic efficiency, and DC resistance measurements. A maximum lithium plating condition was observed to exist between 4C and 5C, thereby limiting the energy consumption in the extraction process. Post-mortem film thickness measurement showed an incrementing film deposition with a maximum of 35 µm thickness. SEM and XPS analysis confirmed increasing concentration of a dense dendritic metallic lithium deposition on the anode/separator interface with C-rate. A green recovery process was adopted to extract the concentrated metallic lithium using distilled water. The lithium from the plated film, solid/electrolyte interface (SEI), electrolyte, anode, and cathode, was extracted as salts. A 37% improvement in lithium recoverability was achieved with fast charging under ambient conditions. XPS analysis showed ~92% of lithium yield with no residual lithium in the graphite. In addition, the battery-grade graphite was recovered with 97% purity after heat treatment of the washed anode film, and concentrated transition metals oxides in the cathode to 93% purity for convenient extraction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-Capacity Organic Radical Mediated Phosphorus Anode for Sodium-Based Redox Flow Batteries

An innovative approach to improve the energy density of redox flow batteries (RFBs) through electrochemically mediated reactions is demonstrated. Soluble anion radical species (biphenyl and pyrene) mediate reversible sodium storage in a red phosphorus (P) anode located in an external packed bed reactor in the absence of binders or conductive additives. Because the anion radical species can be recycled several times through the cell stack during a single charge/discharge cycle, a mediated RFB effectively decouples the battery’s energy density from the redox species’ solubility in the electrolyte. The present study demonstrates the highest capacity reported to date for a mediated anode (up to 800 mAh/gP via reversible formation of Na x P). Finally, this approach represents a paradigm shift in the field and can conceivably achieve energy densities exceeding 200 Wh/kg, which is ~10 times greater than that of conventional RFBs (e.g., 25 Wh/kg for an aqueous vanadium system).

25 ENERGY STORAGE↗

Durable and self-hydrating tungsten carbide-based composite polymer electrolyte membrane fuel cells

Proton conductivity of the polymer electrolyte membranes in fuel cells dictates their performance and requires sufficient water management. Here, we report a simple, scalable method to produce well-dispersed transition metal carbide nanoparticles. We demonstrate that these, when added as an additive to the proton exchange Nafion membrane, provide significant enhancement in power density and durability over 100 hours, surpassing both the baseline Nafion and platinum-containing recast Nafion membranes. Using focused ion beam/scanning electron microscope tomography reveals the key membrane degradation mechanism. Density functional theory exposes that OH• and H• radicals adsorb more strongly from solution and reactions producing OH• are significantly more endergonic on tungsten carbide than on platinum. Consequently, tungsten carbide may be a promising catalyst in self-hydrating crossover gases while retarding desorption of and capturing free radicals formed at the cathode, resulting in enhanced membrane durability.

30 DIRECT ENERGY CONVERSION↗

Experimental Determination and Thermodynamic Modeling of Electrical Conductivity of SRS Waste Tank Supernate

SRS High Level Waste Tank Farm personnel rely on conductivity probes for detection of incipient overflow conditions in waste tanks. Minimal information is available concerning the sensitivity that must be achieved such that that liquid detection is assured. Overly sensitive electronics results in numerous nuisance alarms for these safety-related instruments. In order to determine the minimum sensitivity required of the probe, Tank Farm Engineering personnel need adequate conductivity data to improve the existing designs. Little or no measurements of liquid waste conductivity exist; however, the liquid phase of the waste consists of inorganic electrolytes for which the conductivity may be calculated. Savannah River Remediation (SRR) Tank Farm Facility Engineering requested SRNL to determine the conductivity of the supernate resident in SRS waste Tank 40 experimentally as well as computationally. In addition, SRNL was requested to develop a correlation, if possible, that would be generally applicable to liquid waste resident in SRS waste tanks. A waste sample from Tank 40 was analyzed for composition and electrical conductivity as shown in Table 4-6, Table 4-7, and Table 4-9. The conductivity for undiluted Tank 40 sample was 0.087 S/cm. The accuracy of OLI Analyzer™ was determined using available literature data. Overall, 95% of computed estimates of electrical conductivity are within ±15% of literature values for component concentrations from 0 to 15 M and temperatures from 0 to 125 °C. Though the computational results are generally in good agreement with the measured data, a small portion of literature data deviates as much as ±76%. A simplified model was created that can be used readily to estimate electrical conductivity of waste solution in computer spreadsheets. The variability of this simplified approach deviates up to 140% from measured values. Generally, this model can be applied to estimate the conductivity within a factor of two. The comparison of the simplified model to pure component literature data suggests that the simplified model will tend to under estimate the electrical conductivity. Comparison of the computed Tank 40 conductivity with the measured conductivity shows good agreement within the range of deviation identified based on pure component literature data.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

2022 American Conference on Neutron Scattering (ACNS 2022)

The 11th American Conference on Neutron Scattering (ACNS 2022) will be held on June 5-9, 2022, in Boulder, CO. The Conference will provide essential information on the breadth and depth of current neutron-related research worldwide. Hosted by the Neutron Scattering Society of America, this year’s Conference will feature a combination of invited and contributed talks, poster sessions, and tutorials. Topics of the conference are: Advances in Neutron Facilities, Instrumentation and Software: Developments in sources, instrumentation, sample environments and control software. Hard Condensed Matter: Magnetism, correlated metals, quantum/topological materials, superconductors, ferroelectrics, multiferroics, glasses, and disorder phenomena. Submissions outlining examples of neutron scattering in industrial and engineering applications involving hard condensed matter systems are also encouraged. Soft Matter: Neutron studies of soft materials and related fields including in situ and in operando studies. Polymers, surfactants, emulsions, gels, nanoparticles, colloidal suspensions and more. Submissions of computational studies or applications of machine learning beneficial to neutron scattering experiments, as well as examples of neutron scattering in industrial and engineering applications are strongly encouraged. Biology, Biophysics and Biotechnology: Neutron studies of biological and biologically relevant systems. Proteins, bio membranes, biological assemblies, natural materials, nucleic acids, drug-delivery platforms and biomedical systems. Submissions of computational studies or applications of machine learning beneficial to biological neutron scattering experiments, as well as examples of neutron scattering in applied research involving biological systems, are strongly encouraged. Materials Chemistry and Energy: Neutron-based studies of functional materials and materials for energy applications. Examples include porous materials such as metal organic frameworks (MOFs), zeolites; phosphors; novel pigments; electrolytes; catalysts; ionic conductors/cathode materials; photovoltaic materials (hybrid perovskites); thermoelectrics; magnetocalorics/electrocalorics. Structural Materials and Engineering: Neutron scattering studies of materials and engineering processes including structural materials, concrete and metals, as well as engineering processes including combustion, corrosion, additive manufacturing, and others. Neutron Physics: Fundamental physical studies of the neutron and related areas. Emerging Applications in Neutron Scattering: Machine Learning and Data Science: Advances in computing power have contributed to rapidly evolving machine learning and data science fields that can be leveraged to the benefit of the neutron scattering community. The purpose of this session is to highlight recent advances in machine learning and data science and to serve as the foundation of a parallel data and computation track highlighting computation advances and applications in neutron scattering throughout the conference.

36 MATERIALS SCIENCE↗

Mathematical Analysis of High-Temperature Co-electrolysis of CO2 and O2 Production in a Closed-Loop Atmosphere Revitalization System

NASA has been evaluating two closed-loop atmosphere revitalization architectures based on Sabatier and Bosch carbon dioxide, CO2, reduction technologies. The CO2 and steam, H2O, co-electrolysis process is another option that NASA has investigated. Utilizing recent advances in the fuel cell technology sector, the Idaho National Laboratory, INL, has developed a CO2 and H2O co-electrolysis process to produce oxygen and syngas (carbon monoxide, CO and hydrogen, H2 mixture) for terrestrial (energy production) application. The technology is a combined process that involves steam electrolysis, CO2 electrolysis, and the reverse water gas shift (RWGS) reaction. A number of process models have been developed and analyzed to determine the theoretical power required to recover oxygen, O2, in each case. These models include the current Sabatier and Bosch technologies and combinations of those processes with high-temperature co-electrolysis. The cases of constant CO2 supply and constant O2 production were evaluated. In addition, a process model of the hydrogenation process with co-electrolysis was developed and compared. Sabatier processes require the least amount of energy input per kg of oxygen produced. If co-electrolysis replaces solid polymer electrolyte (SPE) electrolysis within the Sabatier architecture, the power requirement is reduced by over 10%, but only if heat recuperation is used. Sabatier processes, however, require external water to achieve the lower power results. Under conditions of constant incoming carbon dioxide flow, the Sabatier architectures require more power than the other architectures. The Bosch, Boudouard with co-electrolysis, and the hydrogenation with co-electrolysis processes require little or no external water. The Bosch and hydrogenation processes produce water within their reactors, which aids in reducing the power requirement for electrolysis. The Boudouard with co-electrolysis process has a higher electrolysis power requirement because carbon dioxide is split instead of water, which has a lower heat of formation. Hydrogenation with co-electrolysis offers the best overall power performance for two reasons: it requires no external water, and it produces its own water, which reduces the power requirement for co-electrolysis.

08 HYDROGEN↗

Human Research Program Human Health Countermeasures Element Cardiovascular Risks Standing Review Panel (SRP)

The Cardiovascular Risk Standing Review Panel (SRP) evaluated several cardiovascular risks associated with space flight along with the ongoing and emerging plans to study these issues and potentially propose and/or develop countermeasures. The areas of focus included: 1) The risk of cardiac rhythm problems during prolonged space flight, and 2) Issues related to the risk of orthostatic intolerance during re-exposure to gravity. An emerging area of concern is radiation associated vascular injury. The risk of cardiac rhythm disturbances has emerged based on case reports only. No systematic study of this risk has been published. However, concerns about this risk are heightened by the age range of astronauts, the structural changes in the heart that occur during space flight, and the potential shifts in fluids and electrolytes. The current plan is to use prolonged Holter monitor EKG records made as part of the "Integrated Cardiovascular SMO" in space to determine more about the frequency and magnitude of this problem and to link this data to complementary data from the nutrition group on electrolytes. The SRP was supportive of this approach. The SRP also felt that any data related to cardiovascular risk in space should be better coordinated with the medical screening data that all astronauts undergo at regular intervals. Additionally, while there are potential privacy issues related to this suggestion, many of the current barriers to better coordination of experimental and clinical data appear to reflect longstanding cultural traditions at NASA that need rethinking. The risk of orthostatic intolerance during re-exposure to gravity was seen by the SRP as an area supported by a wealth of published physiological evidence. The SRP also felt that moving forward with the planned approach to countermeasures was reasonable and that extensive additional hypothesis testing on the physiology of orthostatic intolerance was not needed at this time. There was support for developing ground based models of limited (e.g. 1/6 th) G environments on Earth that generated a number of ideas for consideration by NASA investigators.

Joyner, Michael↗

Rod/Coil Block Copolyimides for Ion-Conducting Membranes

Rod/coil block copolyimides that exhibit high levels of ionic conduction can be made into diverse products, including dimensionally stable solid electrolyte membranes that function well over wide temperature ranges in fuel cells and in lithium-ion electrochemical cells. These rod/coil block copolyimides were invented to overcome the limitations of polymers now used to make such membranes. They could also be useful in other electrochemical and perhaps some optical applications, as described below. The membranes of amorphous polyethylene oxide (PEO) now used in lithium-ion cells have acceptably large ionic conductivities only at temperatures above 60 C, precluding use in what would otherwise be many potential applications at lower temperatures. PEO is difficult to process, and, except at the highest molecular weights it is not very dimensionally stable. It would be desirable to operate fuel cells at temperatures above 80 C to take advantage of better kinetics of redox reactions and to reduce contamination of catalysts. Unfortunately, proton-conduction performance of a typical perfluorosulfonic polymer membrane now used as a solid electrolyte in a fuel cell decreases with increasing temperature above 80 C because of loss of water from within the membrane. The loss of water has been attributed to the hydrophobic nature of the polymer backbone. In addition, perfluorosulfonic polymers are expensive and are not sufficiently stable for long-term use. Rod/coil block copolyimides are so named because each molecule of such a polymer comprises short polyimide rod segments alternating with flexible polyether coil segments (see figure). The rods and coils can be linear, branched, or mixtures of linear and branched. A unique feature of these polymers is that the rods and coils are highly incompatible, giving rise to a phase separation with a high degree of ordering that creates nanoscale channels in which ions can travel freely. The conduction of ions can occur in the coil phase, the rod phase, or both phases.

Meador, Mary Ann B.↗

Ionic Liquid-Enhanced Interfaces to Boost Reactive C O2 Capture

The addition of ionic liquids (ILs) to a mixture containing a molecular solvent and other ionic species can induce the heterogeneous redistribution of cations and anions at the gas–liquid interface. This nonuniform redistribution of cations and anions driven by the differences in the solvophilicity of ions can improve the thermophysical and interfacial properties of such mixtures, creating a local chemical environment that is conducive to some reactions. In this work, ILs are added to a mixture of potassium hydroxide (KOH) and ethylene glycol (EG), used as a reactive absorbent and electrolyte in the migration-assisted moisture-gradient (MAMG) process for CO 2 capture. Molecular dynamics (MD) simulations are employed to probe into the effects of complex ion–ion and ion–solvent interactions and to examine the chemical composition at the gas–liquid interface. A total of 12 systems are investigated using molecular simulations to identify trends in the performance of IL additives based on the choice of cation, anion, and IL concentration. The cation effects are studied using IL additives based on 1-ethyl-3-methylimidazolium ([EMIM] + ) and 1-butyl-3-methylimidazolium ([BMIM] + ), while the impact of anions is examined using additives based on dicyanamide [DCA] − , triflate [TfO] − , bistriflimide [NTf 2 ] − , and hexafluorophosphate [PF 6 ] − anions, respectively. The influence of the IL concentration is also evaluated at molar concentrations between 1% and 4%. The simulation results indicate that the use of IL additives can affect the physical CO 2 solubility, surface tension, and the localization of CO 2 around the [OH] − ions at the gas–liquid interface. It is also evident that the choice of cations, anions, and IL concentration determines the extent to which the IL additives impact the local physicochemical properties. Physical dissolution, diffusive transport, and interaction with [OH] − are critical intermediate steps toward reactive CO 2 capture using a liquid absorbent. Hence, the improvement in one or more of these properties, aided by IL additives, is expected to improve the overall CO 2 capture performance. Experiments reaffirmed the impact of IL additives on CO 2 capture performance and the sensitivity to the choice of the cation, anion, and concentration of the IL additive.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗