Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dissolving”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Final Research Performance Report - Small Molecular Associative Carbon Dioxide (CO 2 ) Thickeners for Improved Mobility Control

The initial objective of this project was to promote the application of a CO 2 thickener for improved mobility control during CO 2 EOR based on solubility tests, viscosity tests, and core floods. Ultimately, it was demonstrated that the CO 2 -soluble polymeric thickeners are much better suited for use a CO 2 -soluble conformance control agents for diverting the flow of CO 2 away from thief zones. Our team generated several effective small molecule CO 2 thickeners with ARPA-e funding. Unfortunately, none of these small molecule thickeners could dissolve in CO 2 without the addition of unacceptably large amounts of hexane or toluene as a co-solvent Therefore none were viable candidates for the core flooding studies associated with NETL award. Therefore during the entire core flood testing program associated with this NETL award, our team used only the most promising polymeric CO 2 thickener, a polyfluoroacrylate (PFA). In order to produce an environmentally benign polymer, the monomer used to make the new polymers used in this study was a fluoroacrylate that contains only six fluorinated carbons. We verified CO 2 solubility with a phase behavior cell. The thickening potential of all polymer samples was substantiated with a falling ball viscometer and a falling cylinder viscometer at Pitt. Two different viscometers were used to determine the increase in CO 2 viscosity that could be achieved via the dissolution of PFA. Praxair, which has an interest in thickening CO 2 for pilot EOR projects and for waterless hydraulic fracturing, agreed to measure the viscosity of CO 2 -PFA solutions at no cost to the project. Falling cylinder viscometery was conducted at Pitt in our windowed high pressure phase behavior cell. Both apparatuses indicated that at very low shear rates the CO 2 viscosity increased by a factor of roughly 3.5 when 1wt% PFA was dissolved in the CO 2 2. Our team also planned thickener concentrations and compositions at Pitt for the core tests that were conducted at Special Core Analysis Laboratories, Inc., (SCAL) in Midland, TX, where the ability for PFA to reduce CO 2 mobility in a core was then tested. During the beginning of these tests, the PFA polymer was then shown to impart reasonable improvements in mobility control during the SCAL core tests; as the CO 2 -PFA solution displaced CO 2 from the core at a constant volumetric flow rate, the pressure drop increased as expected. However, as the test progressed, there was clear and surprising evidence of dramatic reductions in core permeability due to PFA adsorption, especially for sandstones. For example, as the CO 2 -PFA solution displaced pure CO 2 from sandstone and limestone cores, the pressure drop increased by factors of multiple hundreds to over a thousand. It was subsequently demonstrated that the PFA injected into the core either (a) adsorbed strongly and irreversibly onto the rock surfaces, (b) deposited/precipitated within the rock, thereby blocking pores in a manner that could be dislodged by large changes in flow rate or flow direction, or (c) remained in solution and passed completely through the core. The loss of PFA to the porous media and the unacceptably large increases in pressure drop both indicated that PFA was inappropriate for CO 2 EOR mobility control, where thickener adsorption must be minimized and mobility reductions of only 10-100-fold are typically required. However, we realized that because the CO 2 -PFA solution could greatly reduce the permeability of porous media, it could serve as a near wellbore conformance control agent for blocking “thief zones”, where adsorption is acceptable and dramatic increases in pressure drop are desirable. These effects were more dramatic for sandstone than for limestone. Therefore, these PFA fluoroacrylate polymers can serve as a CO 2 -soluble conformance control agent for CO 2 -EOR, especially in sandstone formations. This injection of a single phase solution of CO 2 -PFA for permeability reduction is (to the best of our knowledge) the first report of a CO 2 -soluble conformance control additive. We also demonstrated that the optimal strategy for using CO 2 -PFA solutions for conformance control is analogous to the application of water-based polymeric gels; the CO 2 -PFA solution should first be injected only in an isolated thief zone to induce dramatic reductions in permeability only in that thief zone, and then CO 2 should be injected into all of the zones. Finally, it was noted that given the propensity of PFA to adsorb onto sandstone, the adsorption of PFA from CO 2 -PFA solutions onto cement surfaces promote the sealing of extremely fine cracks in casing cement.

02 PETROLEUM↗

Mark-18A Ion Exchange Raffinate Management Strategy & Processing Recommendations

It is desired to recover Cm-244 through Cm-248 from dissolved Mark-18A targets following anion exchange processing to remove the Pu. The Cm will be sent to Oak Ridge National Laboratory (ORNL) for additional R&D. Approximately 5-8 L per quarter of a Mark-18A target will have undergone anion exchange treatment and will contain Cm. A significant portion of this volume of anion exchange raffinate solution is dissolved fission products not desired to be recovered which could be sent to waste. To reduce the amount of material being sent to ORNL, a waste and volume minimization strategy was developed and is described in this report.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Design and Test Plan for an Integrated Iodine Scrubber and Polishing Bed System

The capture and subsequent immobilization of four regulated volatile radionuclides ( 3 H, 14 C, 85 Kr, and 129 I) and relevant semivolatile species from the off-gas streams of a used nuclear fuel (UNF) reprocessing facility has been a topic of significant research interest on the part of the US Department of Energy and other international organizations. Significant research and development has been conducted over the past decade. In 2016 an initial engineering evaluation and design of the off-gas abatement systems required for a hypothetical 1000 t/yr UNF reprocessing facility treating 5 yr–cooled, 60 GWd/tIHM UNF was completed. One of the key findings of that report was that the consumption rate of silver-based iodine sorbents in the dissolver off-gas primary iodine capture bed is very high and may warrant the evaluation of alternative methods to capture the bulk of the iodine that could significantly reduce the associated frequent remote handing of the iodine filter beds. This report is intended to describe the design of an experimental system that can be used to examine the use of aqueous scrubbing to remove the bulk of the iodine from the dissolver off-gas stream prior to a silver-based solid sorbent that would be used to provide the final iodine capture or polishing step. This report also provides a description of the initial series of tests that are proposed for this system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Performance of Silver-Exchanged Mordenite and Silver-Functionalized Silica-Aerogel Under Vessel Off-gas Conditions

US regulations 40 CFR 61, 40 CFR 190, and 10 CFR 20 govern release limits for volatile radionuclides contained in the gaseous effluents of used nuclear fuel (UNF) reprocessing facilities. Of the four volatile radionuclides that are restricted by the release limits ( 3 H, 14 C, 85 Kr, and 129 I) 129 I will require the greatest degree of abatement. Previous studies have shown that overall plant decontamination factor (DF) for 129 I must, at minimum, exceed 1,000 to meet regulatory requirements. Iodine-containing off-gas will be present in the dissolver off-gas, the cell off-gas, the vessel off-gas (VOG), the waste off-gas, and the shear off-gas. The VOG will most likely contain 1%–5% of the total iodine at part per billion (ppb) concentrations. A number of studies have examined iodine abatement from the dissolver off-gas, which contains greater than 95% of the iodine inventory of the plant, but very few have examined the recovery of iodine from the VOG stream. Reduced silver-exchanged mordenite (Ag 0 Z) has been considered a promising iodine sorbent for use in UNF reprocessing plants, but recent efforts have identified silver-functionalized silica-aerogel (AgAerogel) as a potential alternative. The testing reported here reflects a substantial increase in the body of work available on iodine adsorption by both silver sorbents under prototypical VOG conditions. Both I2 and methyl iodide (CH 3 I) adsorption tests have been conducted with Ag 0 Z and AgAerogel at a range of concentrations up to 1,000 ppb. These experiments were performed with two specific aims: (1) to assess the effect of iodine concentration on its adsorption by the sorbent and (2) to compare the performance of Ag 0 Z and AgAerogel in the removal of iodine from a prototypical VOG stream.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Multifunctional cement for geothermal wells

This report compiles the work of BNL in support of Thermal Shock Resistant Cement evaluations (TSRC) by Schlumberger. BNL has worked on the formulation of thermal-shock resistant cement since 2011. All the materials on the blend including publications and presentations are in public domain and were sent to Schlumberger for review prior the beginning of the evaluations. Initial efforts focused on achieving long and controlled thickening time of TSRC at 85°C in thickening time tests in a pressurized consistometer. Since the results of BNL set control were not reproduced by Schlumberger technical feedback on Schlumberger testing was among the main efforts of the BNL team in the beginning of the collaboration. When it became clear that the main reason of results deviation was the difference in the mode of retarder addition (dry-blended at BNL and pre-dissolved at Schlumberger) the efforts shifted to the possible decrease in the cost of the formulation by changing concentrations and nature of the alkali activator as well as evaluating performance of more economical formulations with calcium-aluminate cement, Secar #51, Secar #71 and Ciment Fondu, suggested by Schlumberger based on communications with Kerneos (supplier of calcium aluminate cements). Another piece of information obtained by Schlumberger from Kerneos that prompted evaluations of different calcium-aluminate cements in the composition of TSRC was the fact that originally used Secar#80 contains some performance-improving additives that may interfere with the set control and rheological properties of the slurries. In summary, the report contains the following information: 1. Review of the setting behavior of TSRC slurries prepared by dry-blending TA powder or pre dissolving it in mix water in calorimetric tests at 85°C; 2. Results of evaluation of different alkali activators for improved compressive strength development and cost reduction; 3. Results of evaluation of Secar #51, 71 and cement Fondu as an alternative to Secar #80 in TSRC formulation – thermal shock tests and phases’ analyses of set cement; 4. A brief discussion of early-compressive-strength-development test conditions appropriate for geothermal wells.

15 GEOTHERMAL ENERGY↗

Multifunctional Cement for Geothermal Wells

This report compiles the work of BNL in support of Thermal Shock Resistant Cement evaluations (TSRC) by Schlumberger. BNL has worked on the formulation of thermal-shock resistant cement since 2011. All the materials on the blend including publications and presentations are in public domain and were sent to Schlumberger for review prior the beginning of the evaluations. Initial efforts focused on achieving long and controlled thickening time of TSRC at 85°C in thickening time tests in a pressurized consistometer. Since the results of BNL set control were not reproduced by Schlumberger technical feedback on Schlumberger testing was among the main efforts of the BNL team in the beginning of the collaboration. When it became clear that the main reason of results deviation was the difference in the mode of retarder addition (dry-blended at BNL and pre-dissolved at Schlumberger) the efforts shifted to the possible decrease in the cost of the formulation by changing concentrations and nature of the alkali activator as well as evaluating performance of more economical formulations with calcium-aluminate cement, Secar #51, Secar #71 and Ciment Fondu, suggested by Schlumberger based on communications with Kerneos (supplier of calcium aluminate cements). Another piece of information obtained by Schlumberger from Kerneos that prompted evaluations of different calcium-aluminate cements in the composition of TSRC was the fact that originally used Secar#80 contains some performance-improving additives that may interfere with the set control and rheological properties of the slurries. In summary, the report contains the following information: 1. Review of the setting behavior of TSRC slurries prepared by dry-blending TA powder or pre dissolving it in mix water in calorimetric tests at 85°C; 2. Results of evaluation of different alkali activators for improved compressive strength development and cost reduction; 3. Results of evaluation of Secar #51, 71 and cement Fondu as an alternative to Secar #80 in TSRC formulation – thermal shock tests and phases’ analyses of set cement; 4. A brief discussion of early-compressive-strength-development test conditions appropriate for geothermal wells.

36 MATERIALS SCIENCE↗

Mechanisms for Methane Transport and Hydrate Accumulation in Coarse-Grained Reservoirs

The distribution of natural methane hydrate within high saturation reservoirs and mechanisms that control the migration of methane are an active area of research. In this project, we studied methane migration mechanisms and associated hydrate accumulation rates in coarse-grained sands of the Terrebonne Basin, located in Walker Ridge Block 313 (WR313), northern Gulf of Mexico. Hydrate in this area is distributed heterogeneously within ~900 m of methane hydrate stability zone, in both thick (10-25 m) and thin (< 3 m) sand layers, and in units of subvertical hydrate-filled fractures. We investigated hydrate formation from diffusively and advectively supplied methane using one-, two-, and three-dimensional basin modeling with inputs from well log and seismic data. The hydrate accumulations at WR313 can mostly be explained by short, diffusive migration of methane as well as short-range advective transport of methane from clays into neighboring coarser-grained layers. This is likely enhanced by small-scale lithologic variations, including local microbial methanogenesis in interbedded clays. Furthermore, our work shows overpressure in clay sediments surrounding sand reservoirs may enhance short-range diffusive migration. Long-range migration of dissolved methane and gas mainly influence hydrate saturation right at the base of the hydrate stability zone, although the dissolved phase can be channeled upwards along sands by compaction-driven flow. Capillary effects can allow gas bubbles to migrate appreciable distances above the predicted base of gas hydrate stability, possibly reaching a few tens of meters into the hydrate stability zone. Recycling methane from hydrate buried beneath the base of the hydrate stability zone can concentrate hydrate at large saturations within a few tens of meters of the base of hydrate stability.

58 GEOSCIENCES↗

DOE/DOT Crude Oil Characterization Research Study, Task 2 Test Report on Evaluating Crude Oil Sampling and Analysis Methods, Revision 1 - Winter Sampling

The Crude Oil Characterization Research Study is designed to evaluate whether crude oils currently transported in North America, including those produced from “tight” formations, exhibit physical or chemical properties that are distinct from conventional crudes, and how these properties associate with combustion hazards that may be realized during transportation and handling. The current report presents results from Task 2, investigating which commercially available methods can accurately and reproducibly collect and analyze crude oils for vapor pressure and composition, including dissolved gases. This issue, Revision 1 – Winter Sampling, incorporates additional seasonal data and compositional analysis results that have become available since publication of a prior report, SAND2017-12482, released in December 2017. Both reports compare performance of commercially available methods to that of a well-established mobile laboratory system that currently serves as the baseline instrument system for the U.S. Strategic Petroleum Reserve Crude Oil Vapor Pressure Program. The experimental matrix evaluates the performance of selected methods for (i) capturing, transporting, and delivering hydrocarbon fluid samples from the field to the analysis laboratory, coupled with (ii) analyzing for properties related to composition and volatility of the oil, including vapor pressure, gas-oil ratio, and dissolved gases and light hydrocarbons. Several combinations of sample capture and analysis were observed to perform well in both summer and winter sampling environments, though conditions apply that need to be considered carefully for given applications. Methods that perform well from Task 2 will then be utilized in subsequent Task 3 (combustion studies) and Task 4 (compositional analyses of multiple crude types), to be addressed in subsequent reports.

02 PETROLEUM↗

Low Temperature Aluminum Dissolution (LTAD) Real Waste Testing of the November 2017 Tank 51 Slurry Sample

Low Temperature Aluminum Dissolution (LTAD) will be performed on Tank 51 sludge prior to sending Sludge Batch 10 to the Defense Waste Processing Facility (DWPF), such that a sizable fraction of the insoluble aluminum will be dissolved and removed. During LTAD, the free hydroxide concentration and temperature of the sludge slurry are both raised, resulting in significantly increased aluminum solubility, which facilitates aluminum removal via decanting of the liquid phase. This Research and Development task will provide input information regarding the expected gas generation rates under the bounding temperature and free hydroxide conditions of the upcoming Tank 51 LTAD evolution. It will also provide information on the expected fraction of insoluble aluminum that will dissolve as a function of temperature and time, as well as the expected chemical and phys ical properties of the Tank 51 sludge slurry, prior to and following the LTAD operations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

2017 Annual Reuse Report for the Idaho National Laboratory Site's Advanced Test Reactor Complex Cold Waste Ponds

This report describes conditions and information, as required by the state of Idaho, Department of Environmental Quality Reuse Permit I-161-02, for the Advanced Test Reactor Complex Cold Waste Ponds located at Idaho National Laboratory from November 1, 2016–October 31, 2017. The effective date of Reuse Permit I-161-02 is November 20, 2014 with an expiration date of November 19, 2019. A permit modification, I-161-02: Modification 1, became effective March 7, 2017. The modification incorporated clarification to the delivery of analytical reports and chain of custody forms. This report contains the following information: • Facility and system description • Permit required effluent monitoring data and loading rates • Permit required groundwater monitoring data • Status of compliance activities • Issues • Discussion of the facility’s environmental impacts. During the 2017 permit year, 234.05 million gallons of wastewater were discharged to the Cold Waste Ponds which is below the maximum annual permit limit of 375 million gallons. Sulfate and total dissolved solids concentrations continue to remain highest in well USGS-065, which is the closest downgradient well to the Cold Waste Ponds. As shown by the groundwater sampling data, sulfate and total dissolved solids concentrations decrease rapidly as the distance downgradient from the Cold Waste Ponds increases. The concentrations of all permit-required parameters were below their respective groundwater quality standard levels (IDAPA 58.01.11) for all six groundwater monitoring wells. There was one noncompliance with the Reuse Permit during the 2017 permit year. Approximately 600 gallons of cooling water was discharged to ground surface outside of the designated application site. DEQ was notified of the noncompliance.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Status of Metallic Structural Materials for Molten Salt Reactors

In the US and around the world, significant interest surrounds development and deployment of nuclear systems using molten salts to transfer heat. Several configurations are being explored, including the use of fluoride salts either as the primary coolant of a reactor with solid fuel or with the fissile material dissolved in the salt. Molten Salt Reactors (MSRs) with fluoride salt typically have a thermal neutron spectrum. There are also fast-spectrum reactors that could use chloride salts to transfer heat. As a result of operation of the Molten Salt Reactor Experiment (MSRE) at Oak Ridge National Laboratory during the 1960s, a system with uranium fuel dissolved in a fluoride-salt medium is the most well-established technology. A nickel alloy with about 6%Cr and molybdenum as a solid solution strengthening agent was developed and deployed for all structural applications in this reactor. The alloy was commercialized as Hastelloy N. During these experiments and in post-decommissioning characterization of material behavior, it was determined that the most significant challenges for structural materials are embrittlement, from helium introduced by transmutation of Ni, and corrosion and grain boundary embrittlement from the fission product tellurium. The MSRE had an outlet temperature of approximately 650°C. The mechanical properties of Hastelloy N are not sufficient to support long-term operation of an MSR above this temperature. Qualification of a material for use in the ASME Boiler and Pressure Vessel Code, Section III, “Rules for Construction of Nuclear Facility Components,” Division 5, “High Temperature Reactors,” will facilitate licensing with the Nuclear Regulatory Commission. Hastelloy N has not been qualified for use in nuclear construction, and significant additional characterization would be required for Code qualification. Given that this alloy is susceptible to He embrittlement and has limited high-temperature strength, it is not recommended that Code qualification be pursued. Instead, it is recommended that a systematic development program be initiated to develop new nickel alloys that contain a fine, stable dispersion of intermetallic particles to trap He at the interface between the matrix and particle and with increased solid solution strengthening from addition of refractory elements. Extensive screening of attractive alloy compositions for elevated temperature strength, microstructural stability, weldability, and resistance to He embrittlement (characterized using ion implantation) will lead to an alloy down-selection for commercialization and Code qualification.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sodium Freezing and Remelting Tests in FY 2018

In FY 2017 and FY 2018, a total of thirteen tests were successfully performed in the Sodium Freezing and Remelting test facility. Each new test was carefully designed based upon the results and findings of the previous test to investigate the effects of different factors on the sodium freezing phenomena, including dissolved Ar cover gas versus vacuum, test section cooling rate during freezing, different freezing patterns (e.g., from the free surfaces inward toward the center versus from the center toward the free surfaces), and Ar cover gas pressure. The freezing results were found to depend upon a combination of phenomena. As more tests were conducted and lessons learned, the conduct of the tests improved. In particular, the last three experiments, Tests 11 through 13, may be singled out as providing representative data under well controlled conditions. The maximum stresses arising from sodium freezing are measured to be quite mild. In the tests, a maximum strain change of 60 radial micro strains was measured, equivalent to a stress/negative pressure of 77 psi. This mild maximum stress is thought to reflect the low yield stress of solid sodium near the freezing temperature. Evidence for yielding of solid sodium is provided by the visual observation of a depression in the frozen sodium free surface inside of the sodium reservoir in one test. It is thought that contraction of sodium in the test section during freezing pulled downward on the frozen sodium at the free surface creating the depression. The authors are not aware of any data for the yield stress of solid sodium or the stress versus strain behavior of solid sodium (sodium is not a structural material). It is thus not possible to directly compare with the solid sodium yield strength. However, stress versus strain data at different temperatures up to the freezing temperature are available for solid lithium which is also a alkali metal and has a low yield strength similar to the maximum stresses determined from the Sodium Freezing and Remelting tests providing support for the interpretation of the results in terms of yielding of solid sodium. This is a good result for Sodium-Cooled Fast Reactors and sodium facilities. The maximum stress due to frozen sodium pulling inward upon a structural wall wetted by sodium and to which the sodium adheres will be limited by the low sodium yield stress. Argon has a significant solubility in sodium. Cavitation due to nucleation of dissolved argon can offset the effects of sodium thermal contraction and alleviate the formation of stress/negative pressure. This is also a good result for Sodium-Cooled Fast Reactors and sodium facilities that operate with an argon cover gas. In the tests, it was found that due to the cavitation, the maximum measured strain change during sodium freezing was limited to 10 axial micro strains, or equivalently 55 psi of negative pressure.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Multiscale Modeling of CO 2 Migration and Trapping in Fractured Reservoirs with Validation by Model Comparison and Real-Site Applications (Final Technical Report)

This report documents the accomplishments achieved during the project titled “Multiscale Modeling of CO 2 Migration and Trapping in Fractured Reservoirs with Validation by Model Comparison and Real-Site Applications” funded by the US Department of Energy, Office of Fossil Energy. The objectives of the project were to develop modeling capabilities for predicting CO 2 and brine migration in fractured reservoirs during geologic carbon storage and to investigate the feasibility of carbon storage in fractured reservoirs using the newly developed modeling capabilities. To achieve these objectives new mass transfer functions were developed to adapt existing dual-continuum approaches – a commonly used approach in hydrocarbon reservoir modeling – to the CO 2 -brine system. In the dual-continuum approach the undisturbed rock matrix and the fractures are modeled as two separate continua, which are coupled through mass exchange of CO 2 and brine between the two continua. Mass transfer functions represent the mass exchange between fractures and the rock matrix, without requiring highly resolved numerical grids of individual fractures, thus allowing large modeling domains relevant to geologic carbon storage questions (tens of meters to hundreds of kilometers). Mass transfer functions for the exchange of both free-phase CO 2 and brine between fractures and rock matrix were developed for both the injection phase and the post-injection phase. During the injection phase the fractures are filled with CO 2 , while the rock matrix is initially filled with brine. Therefore, a mass transfer function was developed that is based on vertical displacement of brine by CO 2 in the rock matrix due to gravitational forces. Once CO 2 injection ceases and CO 2 migrates away from the direct vicinity of the injection site, the fractures will begin to re-fill with brine, while the rock matrix will have high CO 2 saturations. For these conditions a mass transfer functions was developed that is based on spontaneous imbibition, as the pore spaces in the rock matrix are much smaller than in the fractures. For formations with low permeability or high capillary entry pressure of the rock matrix, free-phase CO 2 may not be able to enter the rock matrix. However, free-phase CO 2 at the interface between fractures and rock matrix can dissolve into brine resident in the rock matrix. Therefore, additional mass transfer functions were developed based on aqueous-phase diffusion of CO 2 through the rock matrix. These mass transfer functions are based on existing solutions for diffusion and were expanded to be applicable to a variety of block shapes relevant to dual-continuum modeling. Implementations of the newly developed mass transfer functions showed that they give accurate results when compared to highly resolved models. In addition to developing new transfer functions, a new vertically-integrated dual-continuum modeling framework was developed. This development takes advantage of fast vertical segregation of CO 2 and brine in the fractures due to the density difference between CO 2 and brine and the high permeability of the fractures. Therefore, a vertically-integrated vertical equilibrium model for the fractures is coupled with a vertically-distributed model for the rock matrix. The newly developed approach significantly reduces the computational effort, but is only accurate for fracture permeabilities of 100 mD or higher. Finally, the newly developed models were applied to real and hypothetical geologic carbon storage sites to investigate the feasibility of using fractured reservoirs for carbon storage. The general results were, that storage of CO 2 – both as free-phase and dissolved – is feasible, but that storage capacities are likely lower than in unfractured systems. While the high permeability of the fractures reduces the injection pressure (or permits higher injection rates), fast migration of CO 2 may limit the overall storage volume, because CO 2 may escape laterally with not enough of the rock matrix being swept for effective storage.

20 FOSSIL-FUELED POWER PLANTS↗

Final Report: Development of High Light Output Plastic Scintillating and Wavelength-Shifting Fibers

Scintillating plastic optical fibers have increasingly been used as radiation detectors in nuclear and high energy physics research since they were first made in 1965. It is proposed to make fibers which are at least a factor of 2 brighter and thereby improve detection efficiency, spatial resolution and energy resolution. When radiation strikes existing plastic scintillator only the singlet excited states rather than the triplet excited states are used to produce scintillation light. This means only 25% of the deposited energy is available to produce scintillation light. Utilization of phosphorescent molecules should therefore drastically improve the light output. This process has been called “triplet harvesting” and has been successfully demonstrated in improving the light output of “Organic Light Emitting Diodes, OLEDs”. The objective of this proposal is to produce a bright scintillating fiber using triplet harvesting and a light output time constant of a few nanoseconds. In addition, an increase in the light containment will be achieved by using a new low refractive index cladding material. In Phase 1, polystyrene plastic material will be used. Organo-metallic phosphorescent and conventional dyes will be dissolved in the plastic to demonstrate both the desired brightness and fast decay time. Photophysical properties will be measured. Scintillating fiber will be made. Commercial benefits of this new material include providing improved detection of rare events such as the HIGGS BOSON at the billion dollar high energy facilities. and monitoring stored radioactive material. The new material will also play an important role in making improved imaging detection facilities for protecting civilians and facilities against CBRN-E threats. In addition, the resolution will be improved for medical brachytherapy. The results of selected organic dyes dissolved in a polystyrene matrix performing as scintillating samples are presented. The proposed organo-metallic phosphorescent dyes were not used due to lengthy synthesis times and cost. Rather, an attempt was made to harvest triplet energy from polystyrene using appropriately wavelength-matched dyes. Samples studied include films and blocks. Fibers were not manufactured as a suitable set of dyes was not determined.

07 ISOTOPE AND RADIATION SOURCES↗

Plasmonics-Enhanced Photocatalysis for Water Decontamination

We have successfully shown up to 5x enhancement in reaction rate of photocatalytic decomposition of an organic chemical (methyl orange) dissolved in water, by incorporating a layer of aluminum (Al) plasmonic nanostructures on top of a titanium dioxide (TiO 2 ) thin film photocatalyst. The whole sample is immersed in the solution and illuminated with ultraviolet (UV) light. The plasmonics-induced electromagnetic field enhancement drastically increases photo-absorption and electron-hole pair generation at the catalyst surface, thereby enhancing the redox reactions at the catalyst-water interface that break the dissolved organics into non-toxic by-products such as carbon dioxide (CO 2 ). Our results demonstrate that it is indeed feasible to use plasmonics to enhance photochemical reactions. With further optimized plasmonics design and improved fabrication methodology, simulation results suggest rate enhancement factor of over 20x is possible.

36 MATERIALS SCIENCE↗

Biochemical Characterization of the Influences of Pump-and-Treat Remediation on Aquifer Conditions on the Central Plateau of the Hanford Site

The aim of this research was to quantify and characterize the organic carbon present in the subsurface on the Hanford site, specifically where groundwater pump-and-treat (P&T) operations are currently taking place. The primary purpose of P&T is to remediate groundwater contaminants, however water treatment can alter subsurface conditions by introducing a low, but consistent supply of organic carbon to the subsurface. These inputs have not been characterized and the consequences therein have not been considered prior. Approximately 40 L of groundwater from the P&T facility was processed by stepwise ultra-filtration for carbon characterization. Groundwater was first filtered to remove particulate organic carbon (POC) and colloids (operationally defined as > 0.2 µm) and subsequently, two size fractions of dissolved organic carbon (DOC, operationally defined as <0.2 µm), the > 10 kDa fraction and the >5 kDa fraction. POC was analyzed via X-Ray powder Diffraction (XRD) for structural and phase characterization of groundwater particulates. Dissolved organic carbon (10 kDa fraction) was quantified using a total carbon analyzer (NPOC, non-particulate organic carbon) and the chemical character of this carbon further defined by specific UV absorption and Fourier-Transform Ion Cyclotron Resonance - Mass Spectrometry (FTICR-MS). This detailed analysis of groundwater carbon reveals how P&T operations are affecting subsurface nutrient dynamics, which in turn could have a positive feedback on natural attenuation pathways in the 200W contaminant plume at the Hanford Site.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

2020 State of the Science Report, Chapter 7: Changes in Oceanographic Systems Associated with Marine Renewable Energy Devices

Oceanographic processes define the marine environment: the flow of water determines the concentrations of dissolved gases and nutrients, transports sediments, and maintains the habitats and water quality that support marine organisms and healthy ecosystems. Important physical processes in the ocean include, but are not limited to, tidal circulation and basin flushing, wave action, local and basin-scale ocean currents, temperature and salinity gradients, sediment transport forming and shaping coastlines, and the exchange of heat and dissolved gases at the air-water interface. Harnessing energy with marine renewable energy (MRE) devices has the potential to affect these processes in both the nearfield (within a few device lengths) and the farfield (farther from the device, from the scale of multiple devices to the scale of an enclosed basin) by removing energy from the system, changing natural flow patterns around devices, and/or decreasing wave heights. https://tethys.pnnl.gov/publications/state-of-the-science-2020-chapter-7-oceanographic-systems

54 ENVIRONMENTAL SCIENCES↗

Reduced Neutralization Feasibility Study for H-Canyon Accelerated Basin De- Inventory (ABD) Program

An alternative approach to Spent Nuclear Fuel (SNF) and Nuclear Material Processing was developed for future H-Canyon (HCAN) and L-Area operations that involves a paradigm shift from current HCAN, Concentrate, Storage, and Transfer Facility (CSTF), and Defense Waste Processing Facility (DWPF) operations. The alternative, referred to as Accelerated Basin De-inventory (ABD), requires that all Domestic and Foreign Research Reactor SNF currently at the Savannah River Site (SRS) will be dissolved, stored, and then transferred to CSTF without recovery of Highly Enriched Uranium (HEU). Concentrated nitric acid is utilized to dissolve aluminum spent nuclear fuel (ASNF) in HCAN. The vessels and piping in HCAN are fabricated from 304L stainless steel and are ideally suited to handle the acidic waste stream. However, as the waste is transferred to the CSTF and DWPF, it will contact the carbon steel waste tanks in CSTF. In order to prevent corrosion of the carbon steel, the acidic waste is neutralized (i.e., pH adjusted over 11) by the addition of sodium hydroxide (NaOH). The NaOH is added until the final solution contains 1.2 M excess -OH. Additionally, if the waste is not neutralized to a pH greater than 11, then aluminum hydroxide (Al(OH) 3 ) would form, and solids may form in the piping as it is transferred to CSTF. This document presents an analysis of the influence of reducing the excess caustic that is added to the neutralization tanks on the corrosion protection scheme primarily for the CSTF waste tanks. The implications to HCAN and DWPF were also assessed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗