Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “discretization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

A modified model parametrization algorithm for solving a special type of heat and mass transfer systems

A new method for solving nonlinear heat and mass transfer design tasks was considered. Systems using the Number of Transfer Units (NTU) method are a special type of mathematical model of heat and mass exchangers. It was observed, that the NTU models in a form of differential-algebraic equations (DAEs) cannot be directly solved with higher values of NTU. The requirements for consistent initial conditions, as well as numerical limitations of DAEs solvers, result, that the solution to the considered design problems that cannot be obtained by a classical direct shooting procedure. To overcome the presented difficulties, the αDAE model optimization algorithm was adjusted for solving NTU-based models. The new approach consists of 3 main steps: 1) task discretization by a multiple-shooting approach, 2) design an appropriate function $f_{NTU}$(α) to effectively influence the variability of the state variables described by dynamical relations, 3) the iterative numerical optimization algorithm for the new parametrized system. Moreover, computations can be performed by a chosen numerical optimization approach, which can be communicated with an available outer procedure for solving differential-algebraic equations. The presented algorithm was implemented and applied to solve the design task with the NTU model of a counter-flow exchanger. Here, the new approach was used to modify the system dynamics to influence the difficulty of the considered problem. Finally, the presented method enabled failure-free numerical computations for the higher values of the NTU parameter.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Transmission-distribution long-term volt-var planning considering reactive power support capability of distributed PV

High penetration of grid-edge, inverter-based photovoltaic (PV) can cause significant voltage fluctuations not only at the distribution but also at the sub-transmission levels due to PV output intermittency. Traditional reactive power planning approaches do not consider intermittency, nor the possibility of coordinating the control of existing and future volt-ampere reactive resources. This paper proposes a reactive power planning tool for sub-transmission systems to mitigate voltage violations and fluctuations caused by high PV penetration and intermittency with a minimum investment cost. The planning tool coordinates with an optimization-based volt-var operational tool for: a) modeling the coordination of all existing var assets in both sub-transmission and distribution systems to reduce the need of new equipment, and b)selecting a set of scenarios with voltage violations, derived from PV intermittency c) testing the final investment decision. The tool obtains an investment need for each intermittency scenario with a proposed optimal power-flow framework with efficient techniques to handle a high number of discrete variables. Two options are provided for final planning decision: i) a conservative direct combination of investment need solutions and ii) a machine learning-based selection of representative investment needs at most time steps. The final investment decision options are verified using a realistic large-scale sub-transmission system and 5-minute PV and load data. The results show a significant voltage performance improvement with a lower investment cost for additional var equipment compared to conventional approaches.

14 SOLAR ENERGY↗
DOE OSTI2020

Multi-physics modeling of injected nanoparticles effect on remediation of CO 2 leakage through cracks

One potential risk in CO 2 sequestration is the leakage of carbon dioxide, which can result in contamination of underground water, creating potential threats to existing ecosystems. The common leakage pathway is through the pre-existing fractures or discontinuities within cement in the wellbore, incurred by the environmental conditions imposed on the cement. Injecting nanoparticles into pre-existing cracks is one of the most recently proposed ideas for mitigating fracture propagation in cement CO 2 sequestration. To demonstrate the feasibility of this new technology, a numerical approach was taken in this work, as it is challenging to investigate it in a laboratory setting. We proposed a coupled ALE (Arbitrary Lagrangian–Eulerian)–DEM (Discrete Element Method)–peridynamic modeling strategy within the LS-Dyna package to investigate the intertwined interaction among the CO 2 fluid flow, native fluid (e.g., brine), particle clusters, and cracks within the cement. The numerical results demonstrate that injected nanoparticles can effectively reduce the pressure exerted on the crack surface. Accordingly, the potential fracture propagation at the crack tip would be reduced compared to corresponding cases without nanoparticels as pressurized by fluid flow. This result verifies the effectiveness of proposed nanoparticle injection technology. Finally, using this established modeling strategy, the effect of filling particles on the fracture mitigation for different crack geometries (e.g. particle cluster patterns, aspect ratio of crack aperture and length) and CO 2 reservoir pressure are examined. The result shows that injected particles successfully reduce the fracture propagation in these scenarios.

42 ENGINEERING↗
DOE OSTI2021

Inference of Rock Flow and Mechanical Properties from Injection-Induced Microseismic Events During Geologic CO 2 Storage

Monitoring microseismic activities during CO 2 injection into geologic formations is important for ensuring the safety of the storage operations. The resulting data provide insight into the response of the storage formation to CO 2 injection and can be used to infer the underlying rock flow and mechanical properties. In this paper, assimilation of microseismic data is performed for dynamic characterization of the storage formation by using a stochastic simulation model to forecast the microseismic response of a geologic formation during CO 2 injection. Two modeling approaches are adopted to predict the space-time distribution of the injection-induced microseismicity. The first model is based on pore pressure relaxation assumption, while the second model uses coupled flow and geomechanics simulation to establish the complex physical relation between the storage formation properties and the corresponding microseismic responses during CO 2 injection. The stochastic predictive models in each case are used in ensemble data assimilation frameworks to estimate rock properties from the observed microseismic data. Two data assimilation methods are considered: (i) a new ensemble-based stochastic point process filter (EnPPF) that can directly integrate discrete microseismic events, and (ii) a variant of ensemble smoother, known as the ensemble smoother with multiple data assimilation (ES-MDA), which requires continuous representation of microseismic events for assimilation. The two methods are successfully applied to a geologically realistic model of the Farnsworth Field in Texas, with complex geologic flow units and interacting fault systems.

42 ENGINEERING↗
DOE OSTI2022

Development of lean, efficient, and fast physics-framed deep-learning-based proxy models for subsurface carbon storage

In this work, we present deep-learning-based surrogate models for CCUS developed with four different algorithms and a physics-framed two-phase flow problem involving displacement of water by CO 2 . The deep-learning models were trained using 3D datasets describing the pressure plume, CO 2 saturation plume, and water extraction rate generated by numerical simulation. The hyperparameters defining the architecture of the neural networks were optimized to determine the slimmest network size and training parameters that give the most efficient performance at the least training cost. To develop a robust model that closely mimics the governing physical laws, the discretized form of the two-phase fluid transport equation was used to formulate the supervised deep-learning task. The algorithms investigated in this study predicted the data to above 95% accuracy, with the multi-layer perceptron model demonstrating the best performance by balancing training speed, prediction time, and prediction accuracy with lean network capacity. Furthermore, the surrogate models simultaneously predict reservoir pressure and CO 2 saturation in every grid block, including the surface well extraction rate and bottomhole pressure, at all simulation times for a given static model realization in just a few seconds on a standard desktop computer. A key outcome of this study is that limits can be placed on network design parameters to avoid over designing neural networks, with associated efficiencies in training and prediction times. This is very useful because large volumes of data may be generated in CCUS projects and over-design of neural network architectures imposes penalties that are antithetical to the goal of near-real time forecasting.

58 GEOSCIENCES↗
DOE OSTI2020

CFD-DEM and PR-DNS studies of low-temperature densely packed beds

Over the past few decades, granular media is gaining attention as a viable option for heat transfer fluids (HTFs). Several research efforts are studying the use of particle-based heat transfer fluids in a wide variety of applications. With this motivation, the current work focusses on analyzing the different heat transfer mechanisms in low-temperature mono-sized densely packed granular media. To study the heat transfer behavior of granular media at different scales, the current work employs a two-way coupled computational strategy. The motion of particles is solved using the Discrete Element Method (DEM) and the interstitial air is solved using a Finite-Volume (CFD) approach. The Open-Source library CFDEM Coupling® is used in the current study to join the Finite Volume PISO solver of OpenFOAM® and the DEM solver of LIGGGHTS®. Typically, particle-particle contact conduction and particle-air convection are the most popular closure models. But recent research identified a different heat transfer phenomenon in packed beds that cannot be identified by conduction or convection models. While closure models were developed to implement this on a CFD-DEM framework, they did not capture the effect of intra-particulate thermal gradients on this phenomenon. Hence the current work also employs Particle-Resolved Direct Numerical Simulations (PR-DNS) to gain valuable insights allowing for the modification of existing models. A new closure model is then proposed here and is implemented in the CFD-DEM framework. This model provides key insights into the different heat transfer mechanism of packed beds.

42 ENGINEERING↗
DOE OSTI2020

Quantitative assessment of eddy viscosity rans models for turbulent mixed convection in a differentially heated plane channel

Turbulent mixed convection between two vertical, infinite parallel plates at different temperatures is studied using various two-equation turbulence models. The numerical simulations are performed at a turbulent Reynolds number of Re τ = 150 and a Grashof number of Gr = 9.6 × 10 5 . Comparisons are made against the highly trusted DNS results. Consistent with the DNS approach, the current simulations are performed using constant properties and the Boussinesq approximation to predict the influence of buoyancy. Previous studies have provided assessments of two-equation turbulence models for various scenarios, but often rely on a qualitative “eye” test in order to determine the most appropriate model to predict a given flow. This study aims to provide a new form of quantitative assessment that accounts for both the physics captured by the turbulence model as well as the magnitude of the system response quantities (SRQ) using a modified symmetric mean absolute percent error (SMAPE) method. This method is designed to be approachable to researchers at any level and can be applied to system response quantities from multiple research fields. Uncertainty quantification is also performed to determine the discretization error for each turbulence model. Recommendations are made as to which turbulence models best capture the physics – hydrodynamically and thermally – using both local and global validation metrics. Lastly, a sensitivity analysis is performed on the damping functions used in the most accurate models. This underpins the potential of model developments and adjustments most worth pursuing for buoyant flows. Finally, this framework provides a more physics-based comparative analysis of the selected turbulence models.

42 ENGINEERING↗
DOE OSTI2021

Microbubble dynamics and heat transfer in boiling droplets

Dissipating large heat fluxes from a surface is critically important in numerous industrial and natural applications. Boiling based spray cooling and surface texturing are two of the most promising methods being investigated to address this problem. Although our understanding on these topics has significantly improved over past decades, critical gaps remain in the knowledgebase stymieing the realization of their full potential. As an example, while bubble growth in pool boiling have been investigated in detail, comparatively little is known about how the bubbles evolve inside boiling drops. In the present work, we have investigated for the first time, the microbubble dynamics inside water droplets boiling on superhydrophilic textured substrates using high-speed X-ray phase contrast imaging (XRPCI). Our observations show that the transient bubble density variation follows similar characteristics irrespective of the texture spacing at a given surface temperature. For an example microstructure, we found that the number of discrete bubbles on the surface decreases as temperature is increased although their growth rate increases. Here, we observe that bubble growth is highly non-uniform during the lifetime of a drop on the surface. Initially, bubbles grow under diffusion-limited regime, but at later times they grow as ~t 1.45 due to combined effects of coalescence and evaporation. In some conditions, we found that bubbles shrink dramatically af- ter the initial growth spurt presumably due to severe quenching of the surface, and migration of bubbles on the surface. Using the bubble sizes, for the first time we analyzed the heat flux removed by a single bubble and also by all the bubbles at a given time. We find that the highest dissipation through latent- heat component (~600 W/cm 2 ) occurs just in the beginning and thereafter it decreases. We expect that our findings and the analysis would guide further work on the topic and will aid in the overarching goal of engineering surfaces that are more efficient in boiling heat transfer.

42 ENGINEERING↗
DOE OSTI2021

A fast reduced model for a shell-and-tube based latent heat thermal energy storage heat exchanger and its application for cost optimal design by nonlinear programming

Numerical simulation of latent heat thermal energy storage (LHTES) systems plays a fundamental role in studying the physical process and guiding the engineering design. Discretization of the PDEs describing the nonlinear solidification/melting process of phase change materials (PCMs) leads to a large-scale complex dynamics system, where the system behavior depends on a set of parameters. In a design setting, repeated model evaluations are required over the set of parameters results in significant computational burden. In this paper, an explicit analytic solution was built for the propagation of the solidification front in a cylindrical coordinate. The analytic solution approach is further employed to develop a low computational reduced model (RM) as a module for a shell-and-tube based LHTES heat exchanger. The levelized Cost of Energy (LCOE) is used as a design metric and the RM model is used to apply system-level constraints in the nonlinear programming formulation that facilitates efficient global optimal design of the PCM properties, flow conditions and tube geometries. The use of LCOE as the design metric prevents over design of the heat transfer rate and also establishes a fair ground for evaluation of different thermal storage technologies and their integrated applications with other systems. Optimal results showed that a higher effectiveness results in a higher LCOE; the velocity of the HTF and the length of the channel are highly correlated with each other; both larger PCM latent energy and conductivity result in lower LCOE.

25 ENERGY STORAGE↗
DOE OSTI2022

Experimental measurements and mathematical modeling of cold plate for aviation thermal management

Herein, this study, which has been motivated by the recent applications of the cold plate device in aviation thermal management, reports on physics-based mathematical models derived from the conservation laws of mass, momentum, and energy, and empiricism-based models. One of the objectives of the present work is to report on an elaborate and successful experimental work carried out on an additively manufactured device for the purpose of rigorously validating the numerical predictions. The excellent agreement between the numerical predictions and measured performance provides much needed confidence in the implementation, in the software package, of the offset-strip fin passage correlations, as well as in the software implementation of user-defined wavy fin correlations for aerospace heat exchangers and cold plates operating with ram air at Reynolds numbers below 8000. The contributions of this work can also be found in the development of a new and accurate thermal-hydraulic analysis procedure, referred to in this paper as plate-fin analogy. Results from this procedure are compared with those from thermal resistance network. The comparative study in this paper of the bulk and discrete enthalpy flux method is also new, as is the relative assessment of four off-set strip fin thermal-hydraulic models.

42 ENGINEERING↗
DOE OSTI2023

Bayesian optimal experimental design for constitutive model calibration

Computational simulation is increasingly relied upon for high/consequence engineering decisions, which necessitates a high confidence in the calibration of and predictions from complex material models. However, the calibration and validation of material models is often a discrete, multi-stage process that is decoupled from material characterization activities, which means the data collected does not always align with the data that is needed. To address this issue, an integrated workflow for delivering an enhanced characterization and calibration procedure—Interlaced Characterization and Calibration (ICC)—is introduced and demonstrated. Further, this framework leverages Bayesian optimal experimental design (BOED), which creates a line of communication between model calibration needs and data collection capabilities in order to optimize the information content gathered from the experiments for model calibration. Eventually, the ICC framework will be used in quasi real-time to actively control experiments of complex specimens for the calibration of a high-fidelity material model. This work presents the critical first piece of algorithm development and a demonstration in determining the optimal load path of a cruciform specimen with simulated data. Calibration results, obtained via Bayesian inference, from the integrated ICC approach are compared to calibrations performed by choosing the load path a priori based on human intuition, as is traditionally done. The calibration results are communicated through parameter uncertainties which are propagated to the model output space (i.e. stress–strain). In these exemplar problems, data generated within the ICC framework resulted in calibrated model parameters with reduced measures of uncertainty compared to the traditional approaches.

42 ENGINEERING↗
DOE OSTI2020

Development of a CPU/GPU portable software library for Lagrangian–Eulerian simulations of liquid sprays

The Lagrangian–Eulerian method is widely used for simulations of fuel sprays in turbulent combustion because of the advantage of treating the spray droplets as discrete points. One challenge of the Lagrangian–Eulerian method is the intense computational requirement when tracking the large number of Lagrangian particles needed for high fidelity. We have developed a performance-portable library, Grit, to track the Lagrangian particles in parallel on central processing unit (CPU) and graphics processing unit (GPU) accelerated high performance computing (HPC) architectures. Grit is a C++ library which employs Message Passing Interface (MPI) for distributed memory parallelism and Kokkos programming model for on-node shared memory parallelism with performance portability across different architectures of GPUs and multi-core/manycore CPUs. The parallel algorithms, key parallel kernels, and their performances on the pre-exascale supercomputer, Summit, are presented. Grit is coupled with a direct numerical simulation (DNS) solver, S3D, for multiphase simulations. A conservative formulation has been developed and implemented in Grit for phase coupling with thermodynamic consistency. The formulation separates the conservation of mass, momentum and energy from the physical models to prevent accidental violation of conservation laws due to inconsistent models. The formulation also enforces consistent definitions of enthalpies of the fuel for both phases and the latent heat of evaporation. Finally, simulations of turbulent particle-laden flow and the evaporation of dilute turbulent spray jet are performed to verify the software implementation, and to demonstrate the scalability of Grit for large-scale multiphase simulations.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Thermodynamic Analysis of Nano-Electrospray Induced Gas Jets

Nano-electrospray (nES) produces a plume of charged liquid droplets which have drag interactions with the surrounding gas after they are emitted from a source capillary. The resulting induced gas flow has often been considered unimportant, but we have demonstrated that a gas microjet of significant velocity up to 10s of m/s can be produced. In this work we present a thermodynamic framework that enables analysis of gas jet generation from electrosprays and introduce the important metrics for such analysis, effectiveness (a measure of momentum transfer from the electrosprayed aerosol to gas) and efficiency (a measure of energy conversion from electrical energy generating the electrospray to gas kinetic energy). This analytical framework is applicable to any two-phase flows consisting of discrete conservative-force-driven particles which exchange momentum with an inert, otherwise quiescent fluid medium to yield a co-flowing two-phase jet. Here, we apply this framework to sprays of water from nano-electrospray emitters to demonstrate that increasing the applied electrical potential difference, increasing liquid mass flowrate, and decreasing droplet size all can increase electrospray induced gas jet strength, but only the latter two do so while also increasing the momentum transfer effectiveness and energy conversion efficiency.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

CFD unified approach under Eulerian–Lagrangian framework for methanol and gasoline direct injection sprays in evaporative and flash boiling conditions

Innovative synthetic fuels for advanced propulsion systems, such as methanol and ammonia, and synthetic blended fuels (E00, E10, and E30), known for their high volatility, are often injected directly into combustion chambers. It follows that Eulerian–Lagrangian spray models need to accurately capture the spray collapse as a consequence of flash boiling onset and be capable of proficiently handling the preferential evaporation of multi-component fuels in evaporative scenarios. So, we performed the assessment of an Eulerian–Lagrangian CFD code for simulating methanol and E00 gasoline blend sprays in both early and late injection conditions involving flash boiling conditions and preferential evaporation. The adoption of an effervescent breakup model and of a non-equilibrium phase transition model for the discrete phase allows the adoption of a setup that is almost completely free from specific constant tuning, especially for what concerns the breakup model. We validated the simulations using experimental PLV maps of methanol and E00 sprays issued from the ECN Spray M injector. The results highlight a significantly different morphology of the methanol spray compared to the E00 one under late injection conditions. Under stratified combustion, low-volatile fuels are likely to be ignited first, and the flame propagates toward the high-volatile fuels. In conclusion, the spray collapse was also correctly reproduced, inducing the presence of a low-pressure zone and modifying the spray morphology.

E00↗
DOE OSTI2020

Comparative modeling of the disregistry and Peierls stress for dissociated edge and screw dislocations in Al

Many elementary deformation processes in metals involve the motion of dislocations. The planes of glide and specific processes dislocations prefer depend heavily on their atomic core structures. Atomistic simulations are desirable for dislocation modeling but their application to even sub-micron scale problems is in general computationally costly. Accordingly, continuum-based approaches, such as the phase-field microelasticity, phase-field dislocation dynamics (PFDD), generalized Peierls–Nabarro (GPN) models, and the concurrent atomistic–continuum (CAC) method, have attracted increasing attention in the field of dislocation modeling because they well represent both short-range cores interactions and long-range stress fields of dislocations. To better understand their similarities and differences, it is useful to compare these methods in the context of benchmark simulations and predictions. In this paper, we apply the CAC method and different PFDD variants – one of them is equivalent to a GPN model – to simulate an extended (i.e., dissociated) dislocation in Al with initially pure edge or pure screw character in terms of the disregistry. CAC and discrete forms of PFDD are also employed to calculate the Peierls stress. By conducting comprehensive convergence studies, we quantify the dependence of these measures on time/grid resolution and simulation cell size. Several important but often overlooked differences between PFDD/GPN variants are clarified. In conclusion, our work sheds light on the advantages and limitations of each method, as well as the path towards enabling them to effectively model complex dislocation processes at larger length scales.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The effect of local chemical ordering on Frank-Read source activation in a refractory multi-principal element alloy

In this work, we investigate the operation of Frank-Read (FR) sources in a refractory multi-principal element alloy (MPEA). Simulations of discrete dislocation motion in MPEAs is enabled by the development of a phase field dislocation dynamics model that treats the atomic-scale fluctuations in lattice energies across the glide plane, present due to local ordering in the chemical composition within the nominally random MPEA atomic structure. We consider, through simulation, a range of length scales over which ordering occurs, varying from short-range lengths, a few times dislocation core width, to long-range lengths, an order of magnitude longer than the core. Characteristic of this body-centered cubic MPEA, the simulations also include screw/edge character dependence in glide resistance, as informed by atomic scale simulation. The critical stresses to activate the source for the same source size are found to be statistically distributed, as a direct consequence of the underlying variation in lattice energy. Furthermore, analysis of critical state for activating edge and screw FR sources in the MPEA reveals that FR source operation occurs via a two-step mechanism, involving athermal kink-pair formation, unlike the conventional FR source operation in a material with no composition fluctuations. This mechanism lowers the average critical stress required to activate the FR source and causes the statistical dispersion in critical stress to depend on the range of composition ordering. More importantly, it leads to a more severe dependence of source strength on FR source length than predicted by line tension alone.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Interaction of extended dislocations with nanovoid clusters

Voids of nanoscale dimensions in irradiated metals can act as obstacles to dislocation motion and cause strengthening. In this work, nanovoid strengthening and the influences of void size, void spacing and material properties, such as stacking fault energies, on dislocation bypass mechanisms are investigated using Phase Field Dislocation Dynamics, a three-dimensional mesoscale model that predicts the minimum energy pathway taken by discrete dislocations. A broad range of face centered cubic metals (copper, nickel, silver, rhodium, and platinum) and nanovoid sizes and spacings are treated, altogether spanning void size–to–dislocation stacking fault width ratios from less than unity to ten. Material γ-surfaces, calculated from ab initio methods, are input directly into the formulation. The analysis reveals that the critical bypass stress scales linearly with the linear void fraction, effective isotropic shear modulus, and ratio of the intrinsic to unstable stacking fault energies. With only a few exceptions, the critical stress is controlled by the stress required for the leading partial to impinge the voids (to move within range of the attractive image stress field of the void). When the void diameter is nearly an order of magnitude greater than the stacking fault width, the mechanism determining critical strength shifts to the stress for the dislocation to breakaway after partially cutting the void. Furthermore, this situation corresponds to that treated by line tension models and is realized here for Pt, with a sub-nanometer stacking fault width.

36 MATERIALS SCIENCE↗
DOE OSTI2021

An experimentally validated evaporative phase change heat transfer model for low mass flux applications using R134a in plate heat exchangers

Plate frame heat exchangers are common in liquid-coupled vapor compression systems due to their compactness and ease of maintenance. In some of these systems, the refrigerant within the evaporator can enter the heat exchanger as a subcooled liquid. As a result, the refrigerant passes through three different phases: single-phase liquid, two-phase fluid, and a superheated vapor. Unfortunately, there have been limited prior studies that have identified the best method to predict performance under these circumstances. Furthermore, previous investigations have not evaluated refrigerant evaporation in large industrial sized plate frame heat exchangers under conditions experienced in the present study experimental test facility, especially at mass fluxes below 7 kg m –2 s –1 . In the present investigation, a model was developed to predict the performance of plate and frame heat exchangers when the fluid enters as a subcooled liquid and exits as a superheated vapor. The model used full-sized plate heat exchanger geometry that was discretized into 20 sections to accurately capture local heat transfer and pressure drop effects. The model was validated using an R134a counter flow heat exchanger used in a turbo-compression cooling system test facility that had subcooled liquid entering the evaporator at low mass fluxes. A variety of empirical correlations were evaluated to determine what combination yielded the best predictive capability over the following range of conditions: 5.8 < G < 6.8 kg m –2 s –1 , 2 < q” < 2.8 kW m –2 , and 10 °C < T sat < 15 °C. When the correlations used a fixed control volume length in the heat flux calculation, the most accurate combination resulted in a mean absolute error of 5.5%. Finally, future studies can use the approach described here to optimize heat exchanger size and performance.

42 ENGINEERING↗