Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “controllable loads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Feasibility study of modern airships, phase 2. Volume 1: Heavy lift airship vehicle. Book 1: Overall study results

A Heavy Lift Airship combining buoyant lift derived from a conventional helium-filled non-rigid airship hull with propulsive lift derived from conventional helicopter rotors was investigated. The buoyant lift essentially offsets the empty weight of the vehicle; thus the rotor thrust is available for useful load and to maneuver and control the vehicle. Such a vehicle is capable of providing a quantum increase in current vertical lifting capability. Certain critical deficiencies of past airships are significantly minimized or eliminated.

Source record↗
NASA NTRS1976

Spin tests of a 1/20-scale model of the XP-39 airplane, 15 March 1939

The tests were performed to determine the spinning characteristics of a 1/20-scale model of the Bell XP-39 airplane. Effects of loading changes and of various control dispositions were studied. Subsequent tests were performed to determine the effect of a change in wing dihedral.

Donlan, C. J.↗
NASA NTRS1978

Symmetric voltage-controlled variable resistance

Feedback network makes resistance of field-effect transistor (FET) same for current flowing in either direction. It combines control voltage with source and load voltages to give symmetric current/voltage characteristics. Since circuit produces same magnitude output voltage for current flowing in either direction, it introduces no offset in presense of altering polarity signals. It is therefore ideal for sensor and effector circuits in servocontrol systems.

Vanelli, J. C.↗
NASA NTRS1977

Solid State Remote Power Controllers for high voltage DC distribution systems

Presently, hybrid Remote Power Controllers (RPC's) are in production and prototype units are available for systems utilizing 28VDC, 120VDC, 115VAC/400 Hz and 230VAC/400 Hz. This paper describes RPC development in a new area of application: HVDC distribution systems utilizing 270/300VDC. Two RPC current ratings, 1 amp and 2 amps, were selected for development as they are adequate to control 90% of projected system loads. The various aspects and trade-offs encountered in circuit development are discussed with special focus placed on the circuits that see the duress of the high dc potentials. The comprehensive evaluation tests are summarized which confirmed the RPC compliance with the specification and with system/load compatibility requirements. In addition, present technology status and new applications are summarized.

Billings, W. W.↗
NASA NTRS1978

Multitube turbojet noise-suppression studies using cross-correlation techniques

The noise-generating region of a suppressed turbojet exhaust is studied by cross-correlating static pressure fluctuations within the exhaust with far-field sound for Mach numbers up to 0.99, using a 31-tube nozzle having an area ratio of 3.1. Measurements made with an unsuppressed turbojet exhaust having an equivalent area ratio and operating under effectively equal thrust loads serve as the experimental control. Static pressure-level measurements, made with a calibrated high-temperature acoustically damped probe tube, show that noise suppression by multitube nozzles results from reduced turbulence levels. The maximum fluctuating static-pressure level in the unsuppressed turbojet exhaust is typically 5-6 dB higher than static-pressure levels in the suppressed exhaust under conditions of effectively equal static thrust. This suggests that the turbulence intensity in the multitube suppressor flow is reduced in excess of 20% compared with the unsuppressed jet exhaust.

Regan, D. R.↗
NASA NTRS1979

Interpretive computer simulator for the NASA Standard Spacecraft Computer-2 (NSSC-2)

An Interpretive Computer Simulator (ICS) for the NASA Standard Spacecraft Computer-II (NSSC-II) was developed as a code verification and testing tool for the Annular Suspension and Pointing System (ASPS) project. The simulator is written in the higher level language PASCAL and implented on the CDC CYBER series computer system. It is supported by a metal assembler, a linkage loader for the NSSC-II, and a utility library to meet the application requirements. The architectural design of the NSSC-II is that of an IBM System/360 (S/360) and supports all but four instructions of the S/360 standard instruction set. The structural design of the ICS is described with emphasis on the design differences between it and the NSSC-II hardware. The program flow is diagrammed, with the function of each procedure being defined; the instruction implementation is discussed in broad terms; and the instruction timings used in the ICS are listed. An example of the steps required to process an assembly level language program on the ICS is included. The example illustrates the control cards necessary to assemble, load, and execute assembly language code; the sample program to to be executed; the executable load module produced by the loader; and the resulting output produced by the ICS.

Smith, R. S.↗
NASA NTRS1979

Aircraft wake flow effect and horizontal tail buffet

As part of a program to investigate the fluctuating pressure distribution and response behavior of a fighter aircraft in transonic maneuver, an F-5A scale model has previously been tested in an 11-ft transonic wind tunnel. The model, with a number of static and dynamic pressure transducers imbedded in the lifting surfaces was tested at various angles of attack up to 16 deg. In this paper, test results of particular interest to wake flow and horizontal tail buffet are described. It is shown that the dynamic pressure data on the tail surface at the specified flight conditions serve to determine the local dynamic loads. They also influence the control performance of the aircraft under maneuver conditions where buffet is encountered. The data presented demonstrate a number of contributing factors that affect the tail dynamic pressures in the transonic regime.

Hwang, C.↗
NASA NTRS1982

Load Pulser Is Sparkless

Electronic load pulser uses silicon-controlled rectifier (SCR) and timer to open and close circuit periodically. It replaces a motor-driven mechanical switch, which causes sparks and is unsafe in hazardous environments. Device should find applications in chemical petroleum, and transportation industries.

Washburn, F. D.↗
NASA NTRS1981

Studies of some unconventional systems for solving various landing problems

Solutions to various landing problems were obtained through unconventional systems. The first, of these is the air cushion landing system, where efforts were concentrated on development of adequate braking and steering systems and an improved understanding of scaling laws and behavior. The second was concentrated on use of a wire brush skid as a drag producing device, which was shown to have good friction coefficients and reasonable wear rates at ground bearing pressures up to 689 kPa and forward speeds up to 80 km/hr. The third showed great promise in an active control landing gear where significant load reductions were possible during landing impact and subsequent rollout.

Leland, T. J.↗
NASA NTRS1981

Analytical performance prediction for large antennas

A linear mathematical modeling of the static and dynamic characteristics of a deployable offset wrap rib antenna was attempted using small motions in an effort to simulate the surface distortion resulting from thermal loading and transient oscillations from control. Both cyclic symmetry and model synthesis were used for parametric analysis. Although the ribs can be modeled as slender beams varying cross sections and equivalent linear material properties, the mesh poses a problem since its equivalent stress strain relations are highly nonlinear and sensitive to the biaxial prestressed state. Consequently, the macroscopic material properties were measured experimentally in the neighborhood of the design prestress. An equivalent tangent modulus technique was then adopted about this equilibrium state and assumed to be valid within a small range of incremental stresses.

El-Raheb, M.↗
NASA NTRS1981

In-flight structural dynamic characteristics of the XV-15 tilt rotor research aircraft

The XV-15 tilt rotor research aircraft has recently completed the contractor flight test program at the Bell Helicopter Textron Flight Research Center, Arlington, Texas. During these development and envelope expansion flights (60 flight hours, 140 flights), the aircraft has been tested up to a maximum true airspeed of 557 km/h (346 mph, 301 knts). Results of the structural characteristics obtained during this testing are presented. Included is a discussion concerning the rotor and airframe loads, natural frequency placements, airframe control system interaction, and wing-rotor-pylon aeroelastic stability. Measured data are compared with predicted values for many cases.

Bilger, J. M.↗
NASA NTRS1982

Structures: Propulsion interactions and requirements

The dynamics of the interaction of space structures and their propellant systems are outlined. Optimization for a platform type of space structure is discussed. Static and transient loads, propellant accelerations, tolerances, attitude control, and distributed thrust are considered.

Pengelley, C. D.↗
NASA NTRS1983

Development of a simplified procedure for rocket engine thrust chamber life prediction with creep

An analytical method for predicting engine thrust chamber life is developed. The method accounts for high pressure differentials and time-dependent creep effects both of which are significant in limiting the useful life of the shuttle main engine thrust chamber. The hot-gas-wall ligaments connecting adjacent cooling channels ribs and separating the coolant flow from the combustion gas are subjected to a high pressure induced primary stress superimposed on an alternating cyclic thermal strain field. The pressure load combined with strain-controlled cycling produces creep ratcheting and consequent bulging and thinning of these ligaments. This mechanism of creep-enhanced ratcheting is analyzed for determining the hot-gas-wall deformation and accumulated strain. Results are confirmed by inelastic finite element analysis. Fatigue and creep rupture damage as well as plastic tensile instability are evaluated as potential failure modes. It is demonstrated for the NARloy Z cases analyzed that when pressure differentials across the ligament are high, creep rupture damage is often the primary failure mode for the cycle times considered.

Badlani, M. L.↗
NASA NTRS1984

Aerospace Safety Advisory Panel

An assessment of NASA's safety performance for 1983 affirms that NASA Headquarters and Center management teams continue to hold the safety of manned flight to be their prime concern, and that essential effort and resources are allocated for maintaining safety in all of the development and operational programs. Those conclusions most worthy of NASA management concentration are given along with recommendations for action concerning; product quality and utility; space shuttle main engine; landing gear; logistics and management; orbiter structural loads, landing speed, and pitch control; the shuttle processing contractor; and the safety of flight operations. It appears that much needs to be done before the Space Transportation System can achieve the reliability necessary for safe, high rate, low cost operations.

Source record↗
NASA NTRS1986

CID overview

On December 1, 1984, NASA and the Federal Aviation Administration (FAA) conducted the first remotely piloted air-to-ground crash test of a transport category aircraft. The Full-Scale Transport Controlled Impact Demonstration (CID) was the culmination of 4 years of effort by the two agencies. NASA and the FAA had many objectives during the joint planning and execution of the Controlled Impact Demonstration. The structural loads experiment was very successful. Ninety-seven percent of the channels were active at impact. The data is still being assessed. Only a portion of the data is presented here; approximately 80 channels of data are available. Analysis of the remaining data is in progress. Interior photography was also very successful. One hundred percent of the cameras functioned. The film contains unique information on the development of fire and smoke in the interior of the aircraft. From a human tolerance point of view, the CID was simulation of a survivable crash.

Hayduk, R. J.↗
NASA NTRS1988

The use of the articulated total body model as a robot dynamics simulation tool

The Articulated Total Body (ATB) model is a computer sumulation program which was originally developed for the study of aircrew member dynamics during ejection from high-speed aircraft. This model is totally three-dimensional and is based on the rigid body dynamics of coupled systems which use Euler's equations of motion with constraint relations of the type employed in the Lagrange method. In this paper the use of the ATB model as a robot dynamics simulation tool is discussed and various simulations are demonstrated. For this purpose the ATB model has been modified to allow for the application of torques at the joints as functions of state variables of the system. Specifically, the motion of a robotic arm with six revolute articulations with joint torques prescribed as functions of angular displacement and angular velocity are demonstrated. The simulation procedures developed in this work may serve as valuable tools for analyzing robotic mechanisms, dynamic effects, joint load transmissions, feed-back control algorithms employed in the actuator control and end-effector trajectories.

Obergfell, Louise A.↗
NASA NTRS1989

Airframe/propulsion integration characteristics at transonic speeds

The aerodynamic characteristics for both single and twin-engine high-performance aircraft are significantly affected by shock induced flow interactions as well as other local flow interference effects which usually occur at transonic speeds. These adverse interactions can not only cause high drag, but also cause unusual aerodynamic loadings and/or severe stability and control problems. Many programs are under way to not only develop method for reducing the adverse effects, but also to develop an understanding of the basic flow conditions which are the primary contributors. It is anticipated that these programs will result in technologies which can reduce the aircraft cruise drag through improved integration as well as increase aircraft maneuverability through the application of thrust vectoring. Some of the primary integration problems for twin-engine aircraft at transonic speeds are identified, and several methods are demonstrated for reducing or eliminating the undersirable characteristics, while enhancing configuration effectiveness.

Henderson, William P.↗