Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “circuit optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

The integrated adjustment of chlorine substitution and two-dimensional side chain of low band gap polymers in organic solar cells

A series of conjugated T2 polymers (PBBF1-T2 and PBBCl1-T2), and T3 polymers (PBBF1-T3, PBBCl1-T3 and PBBCl2-T3) were synthesized using chlorinated/fluorinated benzothiadiazole (BT) and the two-dimensional benzo[1,2-b:4,5-b']dithiophene (BDT) units as the building blocks. When compared to the fluorinated polymer, the performance of the polymer photovoltaic devices showed that these chlorinated polymers gave extended optical absorption spectrum, and lower highest occupied molecular orbital (HOMO) energy levels. The introduction of chlorine atoms increases the twist angle between the polymer backbones, and led to a lower HOMO energy level and resulted in the increase of open circuit voltage (V oc) up to 0.84 V in PBBCl2-T3 based devices with a two chlorine substitution. However, the device based on PBBCl1-T3 with only one chlorine atom exhibited the best power conversion efficiency (PCE) which was as high as 6.87% with a V oc of 0.73 V, and this was about 10% higher than that of its fluorinated analogs. Here, this result indicated that the introduction of chlorine atoms into polymers is not only a simple route to synthesize a large amount of material and which avoids the tedious synthesis steps in widely used fluorinated polymers, but it is also a feasible and effective strategy to fine tune the energy level of polymer solar cell with optimized PCE. Furthermore, it is worth noting that the introduction of longer π-conjugation side chains could minimize the influence of chlorine substitution by reducing the twist angle between the polymer backbones, which would reduce the gap of V oc between the chlorinated polymers and their fluorinated analogs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Parameter Estimation and Model Validation of Nonlinear Dynamical Networks

In the performance period of this work under a DOE contract, the co-PIs, Philip Gill and Henry Abarbanel, developed new methods for statistical data assimilation for problems of DOE interest, including geophysical and biological problems. This included numerical optimization algorithms for variational principles, new parallel processing Monte Carlo routines for performing the path integrals of statistical data assimilation. These results have been summarized in the monograph: “Predicting the Future: Completing Models of Observed Complex Systems” by Henry Abarbanel, published by Spring-Verlag in June 2013. Additional results and details have appeared in the peer reviewed literature.

42 ENGINEERING↗

Probing Molecular‐Transport Properties using the Superconducting Proximity Effect

Molecular electronics research focuses on the study and application of molecular building blocks for the fabrication of nanoscale electronic devices, and on utilizing their self‐organization properties to achieve large‐scale electronic circuits. One of the key issues in molecular electronics is to identify the mechanism governing the electrical conductivity along the molecules. More specifically, the problem is to determine whether the junction behaves as a tunnel barrier, or the junction provides electron or hole conduction channels through the molecule. Due to the large energy gap between the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO), it is usually assumed in calculations that the molecule may contain only one conducting channel either for electrons or for holes. Experimentally, measurements using a local‐probe tip or a small gap between two metallic leads strongly depend on the nature of the linkage between the molecules and the contacts, which is hard to optimize. Here, a new approach is presented to study the electronic and transport properties of molecules using the superconducting proximity effect. Insight into these properties is gained by monitoring the modifications of the superconducting properties upon linking nanoparticles to a superconductor via the studied molecules.

Katzir, Eran↗

Implanted Silicon Resistor Layers for Efficient Terahertz Absorption

Broadband absorption structures are an essential component of large format bolometer arrays for imaging GHz and THz radiation. We have measured electrical and optical properties of implanted silicon resistor layers designed to be suitable for these absorbers. Implanted resistors offer a low-film-stress, buried absorber that is robust to longterm aging, temperature, and subsequent metals processing. Such an absorber layer is readily integrated with superconducting integrated circuits and standard micromachining as demonstrated by the SCUBA II array built by ROE/NIST (1). We present a complete characterization of these layers, demonstrating frequency regimes in which different recipes will be suitable for absorbers. Single layer thin film coatings have been demonstrated as effective absorbers at certain wavelengths including semimetal (2,3), thin metal (4), and patterned metal films (5,6). Astronomical instrument examples include the SHARC II instrument is imaging the submillimeter band using passivated Bi semimetal films and the HAWC instrument for SOFIA, which employs ultrathin metal films to span 1-3 THz. Patterned metal films on spiderweb bolometers have also been proposed for broadband detection. In each case, the absorber structure matches the impedance of free space for optimal absorption in the detector configuration (typically 157 Ohms per square for high absorption with a single or 377 Ohms per square in a resonant cavity or quarter wave backshort). Resonant structures with -20% bandwidth coupled to bolometers are also under development; stacks of such structures may take advantage of instruments imaging over a wide band. Each technique may enable effective absorbers in imagers. However, thin films tend to age, degrade or change during further processing, can be difficult to reproduce, and often exhibit an intrinsic granularity that creates complicated frequency dependence at THz frequencies. Thick metal films are more robust but the requirement for patterning can limit their absorption at THz frequencies and their heat capacity can be high. patterned absorber structures that offer low heat capacity, absence of aging, and uniform, predictable behavior at THz frequencies. We have correlated DC electrical and THz optical measurements of a series of implanted layers and studied their frequency dependence of optical absorption from .3 to 10 THz at cryogenic temperatures. We have modeled the optical response to determine the suitability of the implanted silicon resistor as a function of resistance in the range 10 Ohms/sq to 300 Ohms/sq.

Chervenak, J. A.↗

A Genetic Toolbox for Modulating the Expression of Heterologous Genes in the Cyanobacterium Synechocystis sp. PCC 6803

Cyanobacteria, genetic models for photosynthesis research for decades, have recently become attractive hosts for producing renewable fuels and chemicals, owing to their genetic tractability, relatively fast growth, and their ability to utilize sunlight, fix carbon dioxide, and in some cases, fix nitrogen. Despite significant advances, there is still an urgent demand for synthetic biology tools in order to effectively manipulate genetic circuits in cyanobacteria. In this study, we have compared a total of 17 natural and chimeric promoters, focusing on expression of the ethylene-forming enzyme (EFE) in the cyanobacterium Synechocystis sp. PCC 6803. We report the finding that the E. coli σ 70 promoter Ptrc is superior compared to the previously reported strong promoters, such as PcpcB and PpsbA, for the expression of EFE. In addition, we found that the EFE expression level was very sensitive to the 5'-untranslated region upstream of the open reading frame. A library of ribosome binding sites (RBSs) was rationally designed and was built and systematically characterized. We demonstrate a strategy complementary to the RBS prediction software to facilitate the rational design of an RBS library to optimize the gene expression in cyanobacteria. Our results show that the EFE expression level is dramatically enhanced through these synthetic biology tools and is no longer the rate-limiting step for cyanobacterial ethylene production. Furthermore, these systematically characterized promoters and the RBS design strategy can serve as useful tools to tune gene expression levels and to identify and mitigate metabolic bottlenecks in cyanobacteria.

09 BIOMASS FUELS↗

Design and application of ion-implanted polySi passivating contacts for interdigitated back contact c-Si solar cells

Ion-implanted passivating contacts based on poly-crystalline silicon (polySi) are enabled by tunneling oxide, optimized, and used to fabricate interdigitated back contact (IBC) solar cells. Both n-type (phosphorous doped) and p-type (boron doped) passivating contacts are fabricated by ion-implantation of intrinsic polySi layers deposited via low-pressure chemical vapor deposition and subsequently annealed. The impact of doping profile on the passivation quality of the polySi doped contacts is studied for both polarities. It was found that an excellent surface passivation could be obtained by confining as much as possible the implanted-and-activated dopants within the polySi layers. The doping profile in the polySi was controlled by modifying the polySi thickness, the energy and dose of ion-implantation, and the temperature and time of annealing. An implied open-circuit voltage of 721 mV for n-type and 692 mV for p-type passivating contacts was achieved. Besides the high passivating quality, the developed passivating contacts exhibit reasonable high conductivity (R{sub sh n-type} = 95 Ω/□ and R{sub sh p-type} = 120 Ω/□). An efficiency of 19.2% (V{sub oc} = 673 mV, J{sub sc} = 38.0 mA/cm{sup 2}, FF = 75.2%, and pseudo-FF = 83.2%) was achieved on a front-textured IBC solar cell with polySi passivating contacts as both back surface field and emitter. By improving the front-side passivation, a V{sub OC} of 696 mV was also measured.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Development of Lattice-Matched 1.7 eV GalnAsP Solar Cells Grown on GaAs by MOVPE

To advance the state-of-the-art in III-V multijunction solar cells towards high concentration efficiencies approaching 50%, development of a high-quality ~1.7 eV second junction solar cell is of key interest for integration in five or more junction devices. Quaternary GalnAsP solar cells grown lattice-matched on GaAs allows bandgap tunability in the range from 1.42 to 1.92 eV and offers an attractive Al-free alternative to conventional AlGaAs solar cells. In this work, we investigate the role of growth temperature towards understanding the optimal growth window for realizing high-quality GalnAsP alloys. We demonstrate bandgap tunability from 1.6 to 1.8 eV in GalnAsP alloys for compositions close to the miscibility gap, while still maintaining lattice-matched condition to GaAs. We perform an in-depth investigation to understand the impact of varying base thickness and doping concentration on the carrier collection and performance of these 1.7 eV GalnAsP solar cells. The photo-response of these cells is found to be very sensitive to p-type zinc dopant incorporation in the base layer. We demonstrate prototype 1.7 eV GalnAsP solar cell designs that leverage enhanced depletion width as an effective method to overcome this issue and boost long-wavelength carrier collection. Short-circuit current density (JSC) measured in field-aided devices were as high as 17.25 m A/cm2. The best GalnAsP solar cell in this study achieved an efficiency of 17.2% with a JSC of 17 m A/cm2 and a fill-factor of 86.4%. The corresponding open-circuit voltage (VOC) 1.7 eV measured on this cell represents the highest Voc reported for a 1.7 eV GalnAsP solar cell. These initial cell results are encouraging and highlight the potential of Al-free GalnAsP solar cells for integration in the next generation of III-V multijunction solar cells.

14 SOLAR ENERGY↗

Where Have All of the Electrons Gone? Understanding the Role of Alternative Electron Flow and O 2 Reduction in Balancing Cellular Redox (Final Technical Report)

An informed understanding of the fundamentals of light-driven electron transfer reactions in photoautotrophic organisms is necessary to enable improved photosynthetic efficiencies for the production of renewable fuels and novel biomaterials. To obtain high photosynthetic yields, light energy must be efficiently coupled to the fixation of CO 2 . Sub-optimal environmental conditions and metabolic routing (caused by blocks in biosynthetic routes) can severely impact the conversion of light energy to biomass and lead to reactive oxygen production, which in turn can cause cellular damage and productivity losses. Hence, plants, algae, and photosynthetic bacteria have evolved a network of alternative outlets to sustain the flow of photosynthetically derived-electrons. Our research was focused on the nature and integration of these outlets. The data obtained in this project will inform efforts to rationally engineer crop plants and algae to improve photosynthetic yields by enhancing electron transfer reactions to CO 2 reduction and targeted biomass accumulation. A major project research thrust was focused on identifying and quantifying the flow of photosynthetic reductant through electron transfer circuits that result in the light-dependent reduction of O 2 . New energy management strategies were identified that are used when normal carbon assimilation pathways are compromised due to nutrient deprivation, and/or by a reduction in starch synthesis/carbon storage, all conditions resulting in highly reduced intracellular redox pools. The green alga Chlamydomonas reinhardtii, and likely many other algae, have multiple O 2 -reducing pathways that play critical roles in maintaining cellular metabolic balance and scavenging electrons that could potentially cause cellular damage, which in some instances leads to reduced photosynthetic yields but increased fitness. We explored the activities of three essential outlets associated with Chlamydomonas reinhardtii photosynthetic electron transport: (1) reduction of O 2 to H 2 O through Flavodiiron proteins (FLVs) and (2) Plastid Terminal Oxidases (PTOX), and (3) the synthesis of starch. Real-time measurements of O 2 exchange demonstrated that FLVs immediately engage during dark to light transitions, allowing electron transport when the CBBC is not fully activated. Under these conditions, we quantified, for the first time, maximal FLV activity and its overall capacity to direct photosynthetic electrons towards O 2 reduction. However, when starch synthesis is compromised, a greater proportion of electrons is directed toward O 2 reduction through the FLVs, while PTOX, which is sensitive to the PQ pool redox state, is activated. This suggests, that starch synthesis has an important role in priming/regulating CBBC and electron transport. We also identified a biological ‘switch’ in the green alga Chlamydomonas reinhardtii that reversibly restricts photosynthetic electron transport (PET) at the cytochrome b 6 f complex when reductant and ATP generated by PET are in excess of the capacity of carbon metabolism to utilize these products; we specifically show a restriction at this switch when sta6 mutant cells, which cannot synthesize starch, are limited for nitrogen (growth inhibition) and subjected to a dark to light transition. This restriction causes diminished electron flow to PSI, which prevents PSI photodamage, and the plastid alternative oxidase (PTOX) becomes fully activated, serving as an electron valve that dissipates excitation energy absorbed by PSII, thereby lessening PSII photoinhibition. Furthermore, illumination of the cells following the dark acclimation gradually diminishes the restriction at the switch. Future engineering of these switches may allow more effective electron transfer to lipid (biofuel) pathways and diminish the number of electrons “wasted” in the reduction of O 2 to water. Lastly, we explored metabolic routing of electrons during algal fermentation and discovered multiple novel pathways that are activated when the preferred anoxic routes are blocked. These provide valuable products (e.g. lactate, glycerol) that can be used in broad portfolio of biotechnological applications.

59 BASIC BIOLOGICAL SCIENCES↗

AlInP-passivated III–V solar cells grown by dynamic hydride vapor-phase epitaxy

We report the development of AlInP-passivated solar cells grown by dynamic hydride vapor-phase epitaxy (D-HVPE) with AM1.5G efficiencies of 26.0% for single-junction (1J) GaAs cells and 28.0% for GaInP/GaAs (2J) tandems. We compare the device performance of solar cells passivated with AlInP versus control cells passivated with GaInP, which has already enabled near-unity carrier collection in GaAs solar cells. 1J devices passivated with either AlInP or GaInP have an identical open-circuit voltage (V OC ) of 1.06 V and long-wavelength current collection near 95%, indicating that both window materials provide a similar degree of passivation. Adding AlInP passivation to each solar cell structure improves the current collection by 1.3 and 1 mA/cm 2 for the 1J and 2J, respectively. The AlInP also results in a top cell V OC boost of ~40 mV relative to a tandem device passivated only by a thin, highly doped GaInP emitter. Secondary-ion mass spectrometry measurements indicate that although O and Si both incorporate in the AlInP window, they do not appear in the subsequently grown absorber layers and do not impact its ability to passivate the front surface. We expect that these achievements, along with continued optimization, will enable parity of hydride vapor-phase epitaxy (HVPE)-grown device efficiencies with state-of-the-art devices grown by other epitaxial methods in the near future.

14 SOLAR ENERGY↗

Effect of Rubidium Incorporation on the Structural, Electrical, and Photovoltaic Properties of Methylammonium Lead Iodide-Based Perovskite Solar Cells

We report the electrical properties of rubidium-incorporated methylammonium lead iodide ((Rb x MA 1-x )PbI 3 ) films and the photovoltaic performance of (Rb x MA 1-x )PbI 3 film-based p-i-n-type perovskite solar cells (PSCs). The incorporation of a small amount of Rb + (x = 0.05) increases both the open circuit voltage (V oc ) and the short circuit photocurrent density (J sc ) of the PSCs, leading to an improved power conversion efficiency (PCE). However, a high fraction of Rb + incorporation (x = 0.1 and 0.2) decreases the J sc and thus the PCE, which is attributed to the phase segregation of the single tetragonal perovskite phase to a MA-rich tetragonal perovskite phase and a RbPbI 3 orthorhombic phase at high Rb fractions. Conductive atomic force microscopic and admittance spectroscopic analyses reveal that the single-phase (Rb 0.05 MA 0.95 )PbI 3 film has a high electrical conductivity because of a reduced deep-level trap density. We also found that Rb substitution enhances the diode characteristics of the PSC, as evidenced by the reduced reverse saturation current (J 0 ). The optimized (Rb x MA 1-x )PbI 3 PSCs exhibited a PCE of 18.8% with negligible hysteresis in the photocurrent-voltage curve. The results from this work enhance the understanding of the effect of Rb incorporation into organic-inorganic hybrid halide perovskites and enable the exploration of Rb-incorporated mixed perovskites for various applications, such as solar cells, photodetectors, and light-emitting diodes.

14 SOLAR ENERGY↗

Development and Operation of a High Throughput Computer Hard Disk Drive Recycling Enterprise (CRADA NFE-16-05989)

The aim of this collaborative effort is to develop, construct and operate a high throughput computer hard disc drive (HDD) recycling system. Research conducted as part of the Critical Materials Institute (CMI), a Department of Energy (DOE) Energy Innovation Hub, has revealed the economic rationale and the necessary technology for a potentially viable HDD recycling enterprise. Moreover, the very notion of CMI is the development of replacement sources of rare earth critical materials that enable the U.S. to become less dependent on single source supplies. Focused on end-of-life (EOL) consumer products containing rare earth permanent magnets, this cooperative endeavor will develop, construct and operate a highly automated recycling process. Demonstrating economically viable recycling of high value products is largely an untapped resource in the U.S. Recycling HDDs to recover rare earth magnets and other valuable materials (e.g. aluminum, steel, printed circuit boards, copper, etc.) presents a new opportunity to satisfy U.S. demand for highly desirable commodities. The goal of this cooperative research and development agreement (CRADA) project is to create a commercial HDD recycling enterprise that changes the landscape of rare earth magnet material and magnet availability for U.S. manufacturers. Underpinning this primary goal is the development and demonstration of an economic HDD recycling process that provides a significant and alternative supply of rare earth magnets that is not dependent upon foreign sourcing. Oak Ridge National Laboratory (ORNL) has researched the technology options and down selected specific sub-process technologies based upon throughput and economic potential. The participant, however, brings significant process design, development and operational experience that may result in process improvement or optimization strategies that will be explored in collaboration with the contractor. The final outcome of this CRADA is a system/process for recycling large quantities of HDDs. The technology is available for commercial scale-up.

42 ENGINEERING↗

Simulated Impact of Shortened Strings in Commercial and Utility-Scale Photovoltaic Arrays

The deliberate removal of photovoltaic modules from a string can occur for various reasons encompassing maintenance, measurements, theft, or failure, reducing that string length relative to others when replacement modules are not available and there are not any viable alternative makes and models that could be inserted. This phenomenon, delineated in our prior experimentally validated research, manifests two significant effects: (1) a shift in the ideal maximum power point and (2) the induction of potentially substantial reverse currents in the shortened strings at open-circuit voltage, VOC. However, the scalability and asymptotic limits of these observed behaviors concerning array size remained undetermined. In this study, we elucidate the operational dynamics of such arrays by manipulating two mismatch-contributing variables in simulated arrays of up to 900 strings: the number of removed modules per string (indicative of the level of mismatch, ranging up to 5) and the quantity of shortened strings (1 to 60). Simulation outcomes underscore that mismatch severity impacts array operation more than the proportion of shortened strings. This research delves into the practical ramifications of operating with shortened strings, including implications for low-irradiance operation and the manifestation of deleterious reverse currents (>35 A in specific cases), emphasizing the need for careful array configuration for optimal performance and safety in these implementations.

Energy & Fuels↗

Magnetic flux distribution, quasiparticle spectroscopy, and quality factors in Nb films for superconducting qubits

Niobium is a practical material platform for superconducting microwave circuits; however, device-level performance can vary significantly depending on film growth and processing conditions. We compare three epitaxial Nb films grown on $c-$plane sapphire substrates under nominally identical conditions, except for the deposition temperature. To correlate internal quality factors, $Q_{\mathrm {i}}$, with material properties, we combine magneto-optical imaging of magnetic flux distribution with quasiparticle spectroscopy via measurements of the London penetration depth, $λ(T)$. In the low-$Q_{\mathrm i}$ film, there is a lesser ability to screen the magnetic field and an irregular temperature variation of $λ(T)$, implying the existence of localized in-gap states. High $Q_{\mathrm i}$ films show the opposite trend. We conclude that our measurements provide an efficient method for characterizing and optimizing superconducting films for quantum informatics applications.

Datta, Amlan [Ames Lab; Iowa State U.]↗

The ETROC2 as the Final Version for CMS Endcap Timing Layer (ETL) Upgrade

The ETROC (Endcap Timing Readout Chip) is being developed for the LGAD-based CMS Endcap Timing Layer (ETL) at HL-LHC. The ETL on each side of the interaction region will be instrumented with a two-disk system of MIP-sensitive LGAD (Low Gain Avalanche Diodes) silicon devices, read out by ETROCs for precision timing measurement with down to ~30 ps timing resolution per track. The ETROC is designed to handle a 16 x 16 pixel cell matrix, with each pixel being 1.3 mm x 1.3 mm to match the LGAD sensor pixel size. The front-end design for preamplifier and discriminator has been specifically optimized for the reduced LGAD signals, with enough flexibilities to meet the ETL specific needs for time resolution, power budget and radiation profile. The ETROC chip is implemented in a commercial 65nm CMOS process. Each channel consists of a preamplifier, a discriminator, a TDC used for TOA (Time Of Arrival) and TOT (Time Over Threshold) measurements, and a memory for data storage and readout. An in-pixel auto threshold calibration is included, along with a self-testing pattern generator. The TOT is used for time-walk correction of the TOA measurement. The detailed hit information (TOA and TOT) from each cell will be read out from a local circular buffer after each Level-1 Accept (about 1 MHz). In addition, a charge injection circuit is implemented to allow for testing and calibration. For more detailed monitoring of the signal pulses, waveform sampling circuits are included for one pixel. The clock distribution is based on a 16x16 H-tree design with a shielding structure to alleviate potential interference. The global peripheral circuits include a PLL, a phase shifter, an I2C slave controller, a fast control block, a global readout, and a data driver along with an efuse and temperature sensor. The ETROC builds event data frames for each L1A selected event and is also capable of providing L1 trigger information for user-defined delayed hits. The main design challenge is how to extract precision timing information from the small LGAD signals in the presence of high irradiation fluence, while keeping the power consumption and digital activity low. The ETL design goal for the time resolution of 50 ps per hit is required to achieve a 35 ps arrival time measurement for a MIP particle, which has its track registered in two ETL disk layers. The LGAD contribution is known to be about 30 ps, this means that the jitter from the ETROC has to be kept below 40 ps. The ETROC2 is the first full size full functionality prototype design fully compatible with the final chip specifications for CMS ETL and now becomes the final version. The ETROC2 chips have been extensively tested. We will present here new testing results including the bump bonding yield improvement study, the time walk correction (TWC) generality study with one pixel TWC applying to all pixels, the final SEU testing using both heavy ion and proton beam, more beam test studies including different sensors, and readiness for the ETROC2 production for CMS ETL upgrade.

Liu, Tiehui [Fermilab] (ORCID:0009000765225605)↗

Root-Raised Cosine Filter Implementation That Uses Canonical Signed Digits for High-Speed Digital Filter Applications

NASA Lewis Research Center's Space Communications Division has been investigating high-speed digital filters that can operate at a higher speed than those in current use for a digital modulator and demodulator (modem). Using the Canonical Signed Digits (CSD) number representation for filter coefficients is a very effective way to increase the filter's speed while reducing complexity in the digital filter hardware design. This approach is a good alternative to using an expensive parallel-processing design technique or custom, application-specific integrated circuits. Such integrated circuits may not be suitable for applications that require filter speeds faster than what application-specific integrated circuits digital signal processors can offer for a dedicated channel. When a communication channel is a dedicated, multiplication process--a costly, time-consuming process--it can be greatly simplified by a replacement of the filter coefficients with CSD numbers. A computer code written with the MATLAB software package runs the program and generates CSD-represented filter coefficients that are based on minimizing minimum mean square errors. Also, the Alta Group of Cadence's Signal Processing Workstation is used to simulate and analyze the CSD filter responses. The impulse response of the root-raised cosine filter that is used as a base model is defined. From this filter, a set of coefficients is sampled and stored in a file. For the all coefficients, the optimal CSD number for each coefficient is searched on the basis of the minimum-mean-square-errors criterion. Because the distribution of CSD numbers is not uniform, quantization errors tend to be bigger for coefficients greater than 1/2. To offset errors that occur in a region of coefficients between 1/2 to 1 and to better represent fractions with CSD numbers, an extra nonzero digit is allowed for any coefficients exceeding 1/2. This will greatly improve frequency response as well as intersymbol interference at the receiver. The frequency response of a set of collected CSD-represented filter coefficients was compared with the same filter that was conventionally implemented. Analyses show CSD-implemented filters perform as well as conventional filters. Comparison of eye diagrams and bit-error-rate curves between CSD filters and traditionally implemented filters are almost indistinguishable. However, filter complexity was reduced from almost 3.5 to 1 for CSD filters. Complete computer simulation results are available. In the near future, work will focus on building actual working digital filter hardware in a field programmable gate array (FPGA).

Kim, Heechul↗

Ultracompact 3D microfluidics for time-resolved structural biology

To advance microfluidic integration, we present the use of two-photon additive manufacturing to fold 2D channel layouts into compact free-form 3D fluidic circuits with nanometer precision. We demonstrate this technique by tailoring microfluidic nozzles and mixers for time-resolved structural biology at X-ray free-electron lasers (XFELs). We achieve submicron jets with speeds exceeding 160 ms -1 , which allows for the use of megahertz XFEL repetition rates. By integrating an additional orifice, we implement a low consumption flow-focusing nozzle, which is validated by solving a hemoglobin structure. Also, aberration-free in operando X-ray microtomography is introduced to study efficient equivolumetric millisecond mixing in channels with 3D features integrated into the nozzle. Such devices can be printed in minutes by locally adjusting print resolution during fabrication. This technology has the potential to permit ultracompact devices and performance improvements through 3D flow optimization in all fields of microfluidic engineering.

3-D reconstruction↗

X-ray Characterization of a Multichannel Smart-Pixel Array Detector

The Voxtel VX-798 is a prototype X-ray pixel array detector (PAD) featuring a silicon sensor photodiode array of 48 x 48 pixels, each 130 mu m x 130 mu m x 520 mu m thick, coupled to a CMOS readout application specific integrated circuit (ASIC). The first synchrotron X-ray characterization of this detector is presented, and its ability to selectively count individual X-rays within two independent arrival time windows, a programmable energy range, and localized to a single pixel is demonstrated. During our first trial run at Argonne National Laboratory's Advance Photon Source, the detector achieved a 60 ns gating time and 700 eV full width at half-maximum energy resolution in agreement with design parameters. Each pixel of the PAD holds two independent digital counters, and the discriminator for X-ray energy features both an upper and lower threshold to window the energy of interest discarding unwanted background. This smart-pixel technology allows energy and time resolution to be set and optimized in software. It is found that the detector linearity follows an isolated dead-time model, implying that megahertz count rates should be possible in each pixel. Measurement of the line and point spread functions showed negligible spatial blurring. When combined with the timing structure of the synchrotron storage ring, it is demonstrated that the area detector can perform both picosecond time-resolved X-ray diffraction and fluorescence spectroscopy measurements.

CMOS ASIC↗

Demonstration of Scaled-Production of Rare Earth Oxides and Critical Materials from U. S. Coal-Based Sources (Final Report)

The project objective was to demonstrate scaled production of high purity rare earth oxides (REO), nominally exceeding 90% grade, from coal refuse sources using innovative technologies that reduce cost and improve environmental outcomes relative to traditional rare earth processing technologies. The project utilized a critical material pilot plant constructed and tested as part of a previous U.S. Department of Energy project. Target performance criteria was a 50% reduction in production cost based on previous optimum values, 150% increase in recovery and greater than 2% concentrates of rare earth oxides, cobalt and manganese. Concentrate production goals were to produce a rare earth mix oxide product at a rate of 200 grams per day having a minimum purity of 50% as well as products of cobalt and manganese having a minimum purity of 2%. A previous pilot plant investigation identified acid cost as the major contributor to an operating cost that made the recovery of rare earth and other critical metals from bituminous coal sources economically challenging. As such, acid cost reduction was a major target using bio-oxidation reactors to produce sulfuric acid from naturally occurring coal pyrite. Based on laboratory data, a bio-oxidation circuit was designed for the pilot plant to produce 7.5 l/min of acid using two 11-m3 (3000 gallon) reactors equipped with 40 hp aerators for air dispersion. The pilot-scale tests revealed that acid concentration equivalent to as high as 1.0 M sulfuric acid could be continuously produced. However, the bio-acid contained exceptionally high iron concentrations, which complicated downstream processing of the pregnant leach solution (PLS). A TEA of the bio-oxidation circuit showed that production cost was approximately $0.13 per kg acid equivalent if produced using a four-day retention time in the reactors. This value represents a 48% reduction from that of purchased bulk sulfuric acid. Calcination (or roasting) studies were conducted on coarse refuse from West Kentucky No. 13 and Fire Clay coal seam sources. The test results revealed the potential to increase recovery by nearly 100% using temperatures between 500°C to 700°C with light REE recovery value being the most improved. Acid baking of the calcined products using sulfuric acid at 250°C increased heavy rare earth recovery from around 40% to 80% while decreasing the acid requirements by over 50%. The existing pilot plant was upgraded for the pilot scale demonstration of REE and CM recovery. The primary feedstocks were West Kentucky No.13 and heap leach pregnant leach solution (PLS) while a secondary feedstock was a lignite waste material from a construction sand operation. The pilot scale operation started with PLS generation through leaching followed by iron and aluminum removal, nominally at 3.3 and 4.5 pH, respectively. Leaching lixiviants used for the test were industrial grade sulfuric acid or bio-acid generated at the pilot scale facility. For most of the tests, the solid feed rate was 200 lb/hr whereas lixiviant was added at 2 gpm to provide an optimal residence time of 45 minutes. Following the contaminant removal step, several different process schematics were tested with the goal of maximizing REE recovery and purity. In the first test, direct processing of aluminum precipitation raffinate for REE recovery using oxalic acid at pH 1.5 was investigated. Overall REE recovery was approximately 45%. Unfortunately, elevated calcium content in the PLS significantly impacted the RE-Oxide product grade. Similarly, high calcium content decreased both the product purity and grades of CM products. As such, a new flowsheet was tested with the same initial process schematic but different precipitation stages for REEs and CMs at pH 6.0 and 9.0, respectively. It was noted that the overlapping precipitation behavior of Co, Ni and Zn with REEs limited the applicability of this process schematic. While this change increased the RE-Oxide grade from 36% in the first test to 87%, the loss of critical metals to the REE cake and bypass of the REEs to the CM cake significantly impacted the recovery of both REEs and CMs. Therefore, the modified process flowsheet combined oxalic acid precipitation stage raffinate and redissolved CM cake filtrate to maximize both the recovery and purity of the products. Consequently, a RE-Oxide product with 85% purity and CM cakes with over 19% Co, 38% Ni, 14% Zn and 9% Mn content were generated with significantly higher recoveries. While the modified process flowsheet improved recoveries and grades, elemental losses observed in separate precipitation and redissolution losses inspired the adaptation of a single precipitation stage at pH 9.0 for both REEs and CMs. This change was anticipated to maximize the REE recovery while minimizing the costs associated with separated redissolution and processing stages. As expected, REE recovery in this new circuit arrangement was over 56% with a product grade of over 87% RE-Oxide content. Similarly, Co, Ni, Mn, and Zn recoveries of 54%, 40%, 67%, and 66%, respectively, were achieved. Unfortunately, the elevated calcium content present in the solution due to its precipitation at pH 9.0 caused a decrease in the CM cake quality. Therefore, the final process flowsheet involved the addition of calcium oxalate precipitation following the oxalic acid precipitation stage, which effectively eliminated calcium contamination of the CM products. Finally, the pilot scale experiments conducted using bio-acid achieved comparable REE leaching recoveries to the conventional sulfuric acid leaching. Elevated iron concentration in the solution caused the co-precipitation of REEs with the iron and aluminum cake, resulting in the REE losses. Furthermore, elevated iron content bypassing the iron and aluminum precipitation stages contaminated the metal sulfide and manganese cake, respectively. A techno-economic analysis was performed based on a commercial facility capable of treating 500 tph of coal-based material. The production cost for West Kentucky No. 13 coarse refuse material ranged from approximately $500-$700/kg of total rare earth oxide whereas the lignite source had significantly lower production cost of $100-$300/kg. The significant difference in cost was due to the easier leaching characteristics of the lignite material and the higher feed concentrations. All process scenarios resulted in a negative net present value (NPV). For the lignite feedstock, laboratory REE leach recovery values were about 30% higher than the pilot plant data. Using the lab leach results, a positive net present value was achieved and the production cost decreased from $100-$300 $/kg to less than $150/kg of total REO.

01 COAL, LIGNITE, AND PEAT↗