Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “air conditioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Computational design aspects of a NASP nozzle/afterbody experiment

This paper highlights the influence of computational methods on design of a wind tunnel experiment which generically models the nozzle/afterbody flow field of the proposed National Aerospace Plane. The rectangular slot nozzle plume flow field is computed using a three-dimensional, upwind, implicit Navier-Stokes solver. Freestream Mach numbers of 5.3, 7.3, and 10 are investigated. Two-dimensional parametric studies of various Mach numbers, pressure ratios, and ramp angles are used to help determine model loads and afterbody ramp angle and length. It was found that the center of pressure on the ramp occurs at nearly the same location for all ramp angles and test conditions computed. Also, to prevent air liquefaction, it is suggested that a helium-air mixture be used as the jet gas for the highest Mach number test case.

Ruffin, Stephen M.↗

A two-dimensional adaptive-wall test section with ventilated walls in the Ames 2- by 2-foot transonic wind tunnel

The first tests conducted in the adaptive-wall test section of the Ames Research Center's 2- by 2-Foot Transonic Wind Tunnel are described. A procedure was demonstrated for reducing wall interference in transonic flow past a two-dimensional airfoil by actively controlling flow through the slotted walls of the test section. Flow through the walls was controlled by adjusting pressures in compartments of plenums above and below the test section. Wall interference was assessed by measuring (with a laser velocimeter) velocity distributions along a contour surrounding the model, and then checking those measurements for their compatibility with free-air far-field boundary conditions. Plenum pressures for minimum wall interference were determined from empirical influence coefficients. An NACA 0012 airfoil was tested at angles of attach of 0 and 2, and at Mach numbers between 0.70 and 0.85. In all cases the wall-setting procedure greatly reduced wall interference. Wall interference, however, was never completely eliminated, primarily because the effect of plenum pressure changes on the velocities along the contour could not be accurately predicted.

Schairer, Edward T.↗

On the use of external burning to reduce aerospace vehicle transonic drag

The external combustion of hydrogen to reduce the transonic drag of aerospace vehicles is currently being investigated. A preliminary analysis based on a constant pressure control volume is discussed. Results indicate that the specific impulse of the external burning process rivals that of a turbojet and depends on the severity of the initial base drag as well as on the Mach flight number and the equivalence ratio. A test program was conducted to investigate hydrogen-air flame stability at the conditions of interest and to demonstrate drag reduction on a simple expansion ramp. Initial test results are presented and compared with the control-volume analysis. The expansion ramp surface pressure coefficient showed little variation with fuel pressure and altitude, in disagreement with the analysis. Flame stability results were encouraging and indicate that stable combustion is possible over an adequate range of conditions. Facility interference and chemical kinetics phenomena that make interpretation of subscale ground test data difficult are discussed.

Trefny, Charles J.↗

On the use of external burning to reduce aerospace vehicle transonic drag

The external combustion of hydrogen to reduce the transonic drag of aerospace vehicles is currently being investigated. A preliminary analysis based on a constant pressure control volume is discussed. Results indicate that the specific impulse of the external burning process rivals that of a turbojet and depends on the severity of the initial base drag as well as on the Mach flight number and the equivalence ratio. A test program was conducted to investigate hydrogen-air flame stability at the conditions of interest and to demonstrate drag reduction on a simple expansion ramp. Initial test results are presented and compared with the control-volume analysis. The expansion ramp surface pressure coefficient showed little variation with fuel pressure and altitude, in disagreement with the analysis. Flame stability results were encouraging and indicate that stable combustion is possible over an adequate range of conditions. Facility interference and chemical kinetics phenomena that make interpretation of subscale ground test data difficult are discussed.

Trefny, Charles J.↗

Global changes in the 0-70 km thermal structure of the Mars atmosphere derived from 1975 to 1989 microwave CO spectra

J = 1 - 2 (C-12)O (230 GHz) and (C-13)O (220 GHz) spectra of Mars obtained during the particularly favorable opposition of Mars in 1988 are analyzed. A CO mixing ratio is derived for November 1988 which agrees with a determination from 1967 observations. It is demonstrated that if the mixing ratio of CO was not drastically different in early 1980 and early 1982, the low- to midlatitude average thermal structure of the Mars atmosphere at these times was consistent with clear-air radiative-convective equilibrium conditions. Mars atmospheric temperature profiles derived from (C-12)O spectra are also presented.

Clancy, R. Todd↗

A summary of XB-70 sonic boom signature data

A compilation is provided of measured sonic boom signature data derived from 39 supersonic flights (43 passes) of the XB-70 airplane over the Mach number range of 1.11 to 2.92 and an altitude range of 30500 to 70300 ft. These tables represent a convenient hard copy version of available electronic files which include over 300 digitized sonic boom signatures with their corresponding spectra. Also included in the electronic files is information regarding ground track position, aircraft operating conditions, and surface and upper air weather observations for each of the 43 supersonic passes. In addition to the sonic boom signature data, a description is also provided of the XB-70 data base that was placed on electronic files along with a description of the method used to scan and digitize the analog/oscillograph sonic boom signature time histories. Such information is intended to enhance the value and utilization of the electronic files.

Maglieri, Domenic J.↗

Transonic turbine blade cascade testing facility

NASA LeRC has designed and constructed a new state-of-the-art test facility. This facility, the Transonic Turbine Blade Cascade, is used to evaluate the aerodynamics and heat transfer characteristics of blade geometries for future turbine applications. The facility's capabilities make it unique: no other facility of its kind can combine the high degree of airflow turning, infinitely adjustable incidence angle, and high transonic flow rates. The facility air supply and exhaust pressures are controllable to 16.5 psia and 2 psia, respectively. The inlet air temperatures are at ambient conditions. The facility is equipped with a programmable logic controller with a capacity of 128 input/output channels. The data acquisition system is capable of scanning up to 1750 channels per sec. This paper discusses in detail the capabilities of the facility, overall facility design, instrumentation used in the facility, and the data acquisition system. Actual research data is not discussed.

Verhoff, Vincent G.↗

Two-dimensional adaptive-wall tests in the NASA Ames two- by two-foot transonic wind tunnel

The first tests conducted in the adaptive-wall test section of the Ames Research Center's 2- by 2-Foot Transonic Wind Tunnel are described. A procedure was demonstrated for reducing wall interference in transonic flow past a two-dimensional airfoil by actively controlling flow through the slotted walls of the test section. Flow through the walls was controlled by adjusting pressures in compartments of plenums above and below the test section. Wall interference was assessed by measuring (with a laser velocimeter) velocity distributions along a contour surrounding the model, and then checking those measurements for their compatibility with free-air far-field boundary conditions. Plenum pressures for minimum wall interference were determined from empirical influence coefficients. An NACA 0012 airfoil was tested at angles of attack of 0 and 2, and at Mach numbers between 0.70 and 0.85. In all cases the wall-setting procedure greatly reduced wall interference. Wall interference, however, was never completely eliminated, primarily because the effect of plenum pressure changes on the velocities along the contour could not be accurately predicted.

Schairer, Edward T.↗

Transonic turbine blade cascade testing facility

NASA LeRC has designed and constructed a new state-of-the-art test facility. This facility, the Transonic Turbine Blade Cascade, is used to evaluate the aerodynamics and heat transfer characteristics of blade geometries for future turbine applications. The facility's capabilities make it unique: no other facility of its kind can combine the high degree of airflow turning, infinitely adjustable incidence angle, and high transonic flow rates. The facility air supply and exhaust pressures are controllable to 16.5 psia and 2 psia, respectively. The inlet air temperatures are at ambient conditions. The facility is equipped with a programmable logic controller with a capacity of 128 input/output channels. The data acquisition system is capable of scanning up to 1750 channels per sec. This paper discusses in detail the capabilities of the facility, overall facility design, instrumentation used in the facility, and the data acquisition system. Actual research data is not discussed.

Verhoff, Vincent G.↗

Observing the advection of sea ice in the Weddell Sea using buoy and satellite passive microwave data

Data from four buoys tracked by Nimbus 6 and concurrent ice concentrations retrieved from Nimbus 7 scanning multichannel microwave radiometer data are used to investigate the progress and behavior of an area of sea ice as it drifts from the southwestern Weddell Sea. The overall drift characteristics and their relationship to ice edge displacement are examined within the framework of four zones. Three phases are identified in the large-scale behavior of the Weddell Sea ice cover, namely, a rapid equatorward and eastward advance, a quasi-equilibrium phase, and a period of rapid recession. Outbreaks of cold continental air alternate with incursions of relatively warm air from the north; warm conditions are recorded as far as 1200 km in from the ice edge in winter. Closed loops in the buoy trajectories, which are clockwise to the south of 63 deg S, reverse to become anticlockwise to the north. A coherence is observed in the response of the buoys to the passage of storms, even though the buoys separated by a distance of over 100 km.

Massom, Robert A.↗

Stagnation flowfield analysis for an aeroassisted vehicle

Hypersonic reactive flowfield results are presented for the flow about an axisymmetric representation of a three-dimensional aeroassisted vehicle using the viscous shock-layer (VSL) and Navier-Stokes (NS) equations for low- and high-altitude entry conditions, respectively. Solutions are limited to the stagnation region. The NS results have been obtained by employing the surface recombination boundary condition for an 11-species air model, whereas the VSL calculations are carried out by using a 5-species model. Three widely used surface recombination rate models are implemented with these two flowfield calculation procedures. The low-density (or high altitude) NS solutions are obtained with surface slip equations and compare quite well with the direct simulation Monte Carlo predictions. For higher densities (or lower altitudes), the no-slip VSL solutions are considered adequate. Results from this study highlight the effect of surface catalyticity on surface heating and electron number density.

Gupta, Roop N.↗

Interference Tests on NACA Pitot Tubes

In connection with the standardization of instruments used in the wind tunnel, this investigation was undertaken to determine the nature and magnitude of the errors inherent in the measurement of air speed by a pitot tube when the instrument is mounted close to some other body. The mounting of the instrument in proximity to some other body is so frequent in flight and in wind tunnel research that it seemed advisable to investigate thoroughly the magnitude of the possible errors caused by such proximity. The results of this investigation will facilitate comparisons of the errors due to interference which have been reduced to percentages of the air-speed readings obtained under conditions of no interference.

Reid, Elliott G↗

Effect of Fuel on Performance of a Single Combustor of an I-16 Turbojet Engine at Simulated Altitude Conditions

As part of a study of the effects of fuel composition on the combustor performance of a turbojet engine, an investigation was made in a single I-16 combustor with the standard I-16 injection nozzle, supplied by the engine manufacturer, at simulated altitude conditions. The 10 fuels investigated included hydrocarbons of the paraffin olefin, naphthene, and aromatic classes having a boiling range from 113 degrees to 655 degrees F. They were hot-acid octane, diisobutylene, methylcyclohexane, benzene, xylene, 62-octane gasoline, kerosene, solvent 2, and Diesel fuel oil. The fuels were tested at combustor conditions simulating I-16 turbojet operation at an altitude of 45,000 feet and at a rotor speed of 12,200 rpm. At these conditions the combustor-inlet air temperature, static pressure, and velocity were 60 degrees F., 12.3 inches of mercury absolute, and 112 feet per second respectively, and were held approximately constant for the investigation. The reproducibility of the data is shown by check runs taken each day during the investigation. The combustion in the exhaust elbow was visually observed for each fuel investigated.

Zettle, Eugene V↗

Investigation of a Rateau Supercharger for a 700-horsepower Airplane Engine

The Rateau supercharger investigated had, under normal operating conditions, an adiabatic efficiency of 52 percent, the CINA constant-pressure altitude being 6,240 m and the corresponding CINA compression ratio being 2.22. In order to understand the flow conditions in the supercharger, the air velocities at various points, the theoretical delivery heads and a few characteristics were calculated.

Oestrich, Hermann↗

XPS analysis of 440C steel surfaces lubricated with perfluoropolyethers under sliding conditions in high vacuum

This work presents the results of the X-Ray Photoelectron Spectroscopy (XPS) analysis of AISI 440C ball surfaces lubricated with perfluoropolyether (PFPE) oils after friction experiments under sliding conditions at high load in air and vacuum environments. The PFPE lubricants tested were Demnum S100, Fomblin Z-25, and Krytox 143AB. It was found that all the PFPE lubricants were degraded by sliding contact causing the formation of inorganic fluorides on the metallic surfaces and a layer of organic decomposition products. KRYTOX 143AB was the least reactive of the three lubricants tested. It was also found that metal fluoride formed at off-scar areas. This suggests the formation of reactive species, such as COF2 or R(sub f)COF, during sliding experiments, which can diffuse through the lubricant film and react with the metallic surfaces away from the contact region. Comparison of reference specimens before sliding with those that had undergone the sliding tests showed that the amount of non-degraded PFPE remaining on the surface of the balls after the sliding experiments was greater than that of the balls without sliding.

Herrera-Fierro, Pilar↗

Swivel Total-Temperature Probe

Improved probe designed to be mounted at wingtip of airplane and used for measuring total temperature of air when airplane flies at high angles of attack. Four fins and swivel mount enable probe to align itself aerodynamically with local flow of air. Thus, stagnated-flow condition needed for accurate measurement of total temperature achieved.

Moes, Tim↗

Non-linear resonance of fluids in a crystal growth cavity

In the microgravity environment, the effect of gravity on fluid motion is much reduced. Hence, secondary effects such as vibrations, jitters, surface tension, capillary effects, and electromagnetic forces become the dominant mechanism of fluid convection. Numerous studies have been conducted to investigate fluid behavior in microgravity with the ultimate goal of developing processes with minimal influence from convection. Industrial applications such as crystal growth from solidification of melt and protein growth for pharmatheutical application are just a few examples of the vast potential benefit that can be reaped from material processing in space. However, a space laboratory is not immune from all undesirable disturbances and it is imperative that such disturbances be well understood, quantifiable, and controlled. Non-uniform and transient accelerations such as vibrations, jitters, and impulsive accelerations exist as a result of crew activities, space vehicle maneuvering, and the operations of on-board equipment. Measurements conducted on-board a U.S. Spacelab showed the existence of vibrations in the frequency range of 1 to 100 Hz with a dominant mode of 17 Hz and harmonics of 54 Hz. The observed vibration is not limited to any coordinate plane but exists in all directions. Similar situation exists on-board the Russian MIR space station. Due to the large structure of its design, the future International Space Station will have its own characteristic vibration spectrum. It is well known that vibration can exert substantial influence on heat and mass transfer processes, thus hindering any attempts to achieve a diffusion-limited process. Experiments on vibration convection for a liquid-filled enclosure under one-g environment showed the existence of different flow regimes as vibration frequency and intensity changes. Results showed the existence of a resonant frequency, near which the enhancement is the strongest, and the existence of a high frequency asymptote. Numerical simulations of vibration convection have been conducted by Yurkov, Fu and Shieh, and by Wang. These analyses considered a two-dimensional air-filled cell under weightlessness condition and showed results similar to those of the experiments. It is not yet known whether resonance convection can be triggered by jitter alone or whether it requires the interaction of jitter with other convective forces in low gravity. An order of magnitude analysis, however, can be used to show the dependence of the resonance frequency on the fluid Prandtl number. Even though the onset of resonance convection may depend on other factors, results indicates that fluids with low Prandtl numbers are more susceptible to resonance than those with high Prandtl numbers. The current study is aimed at gaining additional insights to this problem using germanium as working fluid. Germanium was chosen for this analysis because of its common usage in solidification process and its relatively low Prandtl number (Pr = 0.02).

Wang, Francis C.↗

Failure Mechanisms During Isothermal Fatigue of SiC/Ti-24Al-11Nb Composites

Failure mechanisms during isothermal fatigue of unidirectional SiC/Ti-24Al-11Nb (at.%) composites have been determined by microstructural analysis of samples from tests interrupted prior to the end of life and from tests conducted to failure. Specimens from three regions of life were examined based on the maximum strain from a fatigue life diagram: Region 1 (high strain), Region 2 (mid-strain) and Region 3 (low strain). Crack lengths were also measured from interrupted samples and compared based on temperature (23-815 C), region of life and numbers of cycles. Region 1 was controlled by fiber-dominated failure. A transition zone was observed between Regions 1 and 2 due to competition between failure mechanisms. Failure in Region 2 was generally described as surface-initiated cracking with varying amounts of fiber bridging. However, the specific descriptions of crack propagation through the fibers and matrix varied with strain and temperature over this broad region. Region 3 exhibited endurance behaviour at 23 C with no cracking after lO(exp 6) cycles. However at 425 C, surface-initiated cracking was observed after 10(exp 6) cycles with fractured fibers in the crack wake. If endurance behaviour exists for conditions of isothermal fatigue in air at temperatures of greater than or equal to 425 C, it may only be found at very low strains and at greater than 10(exp 6) cycles.

Brindley, P. K.↗