Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Transonic calculations for a flexible supercritical wing and comparison with experiment

Pressure data measured on the flexible DAST ARW-2 wing are compared with results calculated using the transonic small perturbation code XTRAN3S. A brief description of the analysis is given and a recently-developed grid coordinate transformation is described. Calculations are presented for the rigid and flexible wing for Mach numbers from 0.60 to 0.90 and dynamic pressures from 0 to 1000 psf. Calculated and measured static pressures and wing deflections are compared, and calculated static aeroelastic trends are given. Attempts to calculate the transonic instability boundary of the wing are described.

Bennett, R. M.↗
NASA NTRS1985

An experimental investigation of propfan installations on an upswept supercritical wing at transonic Mach numbers

An investigation has been conducted in the Langley 16 Foot Transonic Tunnel to determine propfan installation and slipstream interference effects on an unswept supercritical wing. This data can be used for verification of existing and developing theoretical codes as well as giving an understanding of the flow interactions associated with propeller/nacelle/wing integration. The investigation was conducted over a Mach number range of 0.5 to 0.8 and at angles of attack from 0 deg to 3 deg. The propeller was powered by an air turbine simulator and the exhaust from the air turbine was used to simulate the exhaust from the propfan nacelle. Reynolds number based on wing chord varied from 3 to 4 million. Results indicate that the propfan causes an increase in the wing lift coefficient. It was found that most of the propeller induced swirl is recovered by the wing. The propeller slipstream also causes a large favorable leading edge suction peak on the upwash side and a smaller unfavorable decrease on the downwash side.

Bartlett, G. R.↗
NASA NTRS1985

Flight testing the fixed-wing configuration of the Rotor Systems Research Aircraft (RSRA)

The Rotor Systems Research Aircraft (RSRA) is a unique research aircraft designed to flight test advanced helicopter rotor system. Its principal flight test configuration is as a compound helicopter. The fixed wing configuration of the RSRA was primarily considered an energy fly-home mode in the event it became necessary to sever an unstable rotor system in flight. While it had always been planned to flight test the fixed wing configuration, the selection of the RSRA as the flight test bed for the X-wing rotor accelerated this schedule. This paper discusses the build-up to, and the test of, the RSRA fixed wing configuration. It is written primarily from the test pilot's perspective.

Hall, G. W.↗
NASA NTRS1985

An attached flow design of a noninterfering leading edge extension to a thick delta wing

The analytical procedure presented for leading edge extension (LEE) determination, in keeping with such design criteria as noninterference at the wing design point, is applied to thick delta wings. The LEE device thus defined is to be mounted on a wing along a dividing stream surface that is associated with an attached flow design lift coefficient greater than zero. The delta wing in question is of twisted and cambered type. It is demonstrated that span reductions for the candidate LEEs has the most detrimental effect on overall aerodynamic efficiency, irrespective of area or shape.

Ghaffari, F.↗
NASA NTRS1985

Unsteady transonic flow calculations for two-dimensional canard-wing configurations with aeroelastic applications

Unsteady transonic flow calculations for aerodynamically interfering airfoil configurations are performed as a first-step toward solving the three-dimensional canard-wing interaction problem. These calculations are performed by extending the XTRAN2L two-dimensional unsteady transonic small-disturbance code to include an additional airfoil. Unsteady transonic forces due to plunge and pitch motions of a two-dimensional canard and wing are presented. Results for a variety of canard-wing separation distances reveal the effects of aerodynamic interference on unsteady transonic airloads. Aeroelastic analyses employing these unsteady airloads demonstrate the effects of aerodynamic interference on aeroelastic stability and flutter. For the configurations studied, increases in wing flutter speed result with the inclusion of the aerodynamically interfering canard.

Batina, J. T.↗
NASA NTRS1985

Transonic calculations for a flexible supercritical wing and comparison with experiment

Pressure data measured on the flexible DAST ARW-2 wing are compared with results calculated using the transonic small perturbation code XTRAN3S. A brief description of the analysis is given and a recently developed grid coordinate transformation is described. Calculations are presented for the rigid and flexible wing for Mach numbers from 0.60 to 0.90 and dynamic pressures from 0 to 1000 psf. Calculated and measured static pressures and wing deflections are compared, and calculated static aeroelastic trends are given. Attempts to calculate the transonic instability boundary of the wing are described.

Bennett, R. M.↗
NASA NTRS1985

Assessment of preliminary prediction techniques for wing leading-edge vortex flows at supersonic speeds

A theoretical investigation of the aerodynamics of sharp leading-edge delta wings at supersonic speeds has been conducted. The primary objective of this was to determine the applicability of existing theoretical methods to predict wing leading-edge separated-flow characteristics at conditions conductive to high-lift supersonic flight. Predicted results from two modified linear-theory methods (LTSTAR and VORCAM) are compared with experimental data. Comparison of the two methods for uncambered wings revealed that the LTSTAR code is in much better agreement with experimentally measured vortex strength, vortex position, and total lifting characteristics than the VORCAM code. Selected analysis was also performed with an Euler code, SWINT. The results of this study indicated that the SWINT code was not well suited to the analysis of wings with separated flow at high lift and low supersonic speeds.

Wood, R. M.↗
NASA NTRS1985

Oblique wing ready for research aircraft

Performance features and possible design configurations for oblique wings which would lower the supersonic drag characteristics of fighter aircraft are described. The oblique shape reduces wave drag in proportion to the wing length, and can achieve reductions by factors of 4-16. Variable sweep would be accompanied by fuel pumping to maintain an acceptable center of gravity and tail loading. The lift forces remain balanced and thus remove fuselage loads considerations. Extra tail loading to handle longitudinal moments of center-of-lift shifts with variable sweep aircraft are also eliminated. However, oblique wings couple the roll, pitch and yaw axes and require digital controls to provide balancing forces. NASA has initiated a four phase design, construction and flight test program to examine the flight envelope of oblique wings on the F-8 aircraft.

Gregory, T.↗
NASA NTRS1985

The buffeting pressure field of a high-aspect-ratio swept wing

An experimental study of the fluctuating pressure field of a high-aspect-ratio swept transport-type wing model in transonic buffeting flow is examined. A high degree of similarity between the buffet-related features of the wing flowfield and 2-D transonic flowfields is indicated. At several spanwise stations, unsteady lift produced by the pressure fluctuations is evaluated and found to increase in intensity as local flow separation develops. Results show that although the wing does vibrate, the measured lift fluctuations are driving, and not driven by wing vibrations. The influence of tunnel-flow unsteadiness on the data is considered.

Roos, F. W.↗
NASA NTRS1985

Numerical solution of transonic wing flows using an Euler/Navier-Stokes zonal approach

Transonic flow fields about wing geometries are computed using an Euler/Navier-Stokes approach in which the flow field is divided into several zones. The grid zones immediately adjacent to the wing surface are suitably clustered and solved with the Navier-Stokes equations. Grid zones removed from the wing are less finely clustered and are solved with the Euler equations. Wind tunnel wall effects are easily and accurately modeled with the new grid-zoning algorithm because the wind tunnel grid is constructed as an exact subset of the corresponding free-air grid. Solutions are obtained that are in good agreement with experiment, including cases with significant wind tunnel wall effects and shock-induced separation on the upper wing surface.

Holst, T. L.↗
NASA NTRS1985

Pressure-distribution measurements on a transonic low-aspect ratio wing

Experimental surface pressure distributions and oil flow photographs are presented for a 0.90 m semispan model of NASA/Lockheed Wing C, a generic transonic, supercritical, low aspect ratio, highly 3-dimensional configuration. This wing was tested at the design angle of attack of 5 deg over a Mach number range from 0.25 to 0.96, and a Reynolds number range from 3.4 x 1,000,000 to 10 x 1,000,000. Pressures were measured with both the tunnel floor and ceiling suction slots open for most of the tests but taped closed for some tests to simulate solid walls. A comparison is made with the measured pressures from a small model in high Reynolds number facility and with predicted pressures using two three dimesional, transonic full potential flow wing codes: design code FLO22 (nonconservative) and TWING code (conservative). At the given design condition, a small region of flow separation occurred. At a Mach number of 0.82 the flow was unseparated and the surface flow angles were less than 10 deg, indicating that the boundary layer flow was not 3-D. Evidence indicate that wings that are optimized for mild shock waves and mild pressure recovery gradients generally have small 3-D boundary layer flow at design conditions for unseparated flow.

Keener, E. R.↗
NASA NTRS1986

Effects of wing modification on an aircraft's aerodynamic parameters as determined from flight data

A study of the effects of four wing-leading-edge modifications on a general aviation aircraft's stability and control parameters is presented. Flight data from the basic aircraft configuration and configurations with wing modifications are analyzed to determine each wing geometry's stability and control parameters. The parameter estimates and aerodynamic model forms are obtained using the stepwise regression and maximum likelihood techniques. The resulting parameter estimates and aerodynamic models are verified using vortex-lattice theory and by analysis of each model's ability to predict aircraft behavior. Comparisons of the stability and control derivative estimates from the basic wing and the four leading-edge modifications are accomplished so that the effects of each modification on aircraft stability and control derivatives can be determined.

Hess, R. A.↗
NASA NTRS1983

An aerodynamic analysis computer program and design notes for low speed wing flap systems

The expanded capabilities for analysis and design of low speed flap systems afforded by recent modifications of an existing computer program is described. The program provides for the simultaneous analysis of up to 25 pairs of leading-edge and trailing-edge flap deflection schedules. Among other new features of the program are a revised attainable thrust estimation method to provide more accurate predictions for low Mach numbers, and a choice of three options for estimation of leading-edge separation vortex flow effects. Comparison of program results with low speed experimental data for an arrow wing supersonic cruise configuration with leading-edge and trailing-edge flaps showed good agreement over most of the range of flap deflections. Other force data comparisons and an independent study of airfoil and wing pressure distributions indicated that wind-tunnel measurements of the aerodynamic performance of twisted and cambered wings and wings with leading-edge flaps can be very sensitive to Reynolds number effects.

Carlson, H. W.↗
NASA NTRS1986

Natural laminar flow flight experiments on a swept wing business jet-boundary layer stability analyses

The linear boundary layer stability analyses and their correlation with data of 18 cases from a natural laminar flow (NLF) flight test program using a Cessna Citation 3 business jet are described. The transition point varied from 5% to 35% chord for these conditions, and both upper and lower wing surfaces were included. Altitude varied from 10,000 to 43,000 ft and Mach number from 0.3 to 0.8. Four cases were at nonzero sideslip. Although there was much scatter in the results, the analyses of boundary layer stability at the 18 conditions led to the conclusion that crossflow instability was the primary cause of transition. However, the sideslip cases did show some interaction of crossflow and Tollmien-Schlichting disturbances. The lower surface showed much lower Tollmien-Schlichting amplification at transition than the upper surface, but similar crossflow amplifications. No relationship between Mach number and disturbance amplification at transition could be found. The quality of these results is open to question from questionable wing surface quality, inadequate density of transition sensors on the wing upper surface, and an unresolved pressure shift in the wing pressure data. The results of this study show the need for careful preparation for transition experiments. Preparation should include flow analyses of the test surface, boundary layer disturbance amplification analyses, and assurance of adequate surface quality in the test area. The placement of necessary instruments and usefulness of the resulting data could largely be determined during the pretest phase.

Rozendaal, R. A.↗
NASA NTRS1986

Loads calibrations of strain gage bridges on the DAST project Aeroelastic Research Wing (ARW-2)

Results from and details of the procedure used to calibrate strain gage bridges for measurements of wing structural loads, shear (V), bending moment (M), and torque (T), at three semispan stations on both the left and right semispans of the ARW-2 wing are presented. The ARW-2 wing has a reference area of 35 square feet, a span of 19 feet, an aspect ratio of 10.3, a midchord line sweepback angle of 25 degrees, and a taper ratio of 0.4. The ARW-2 wing was fabricated using aluminum spars and ribs covered with a fiberglass/honeycomb sandwich skin material. All strain gage bridges are mounted along with an estimate of their accuracy by means of a comparison of computed loads versus actual loads for three simulated flight conditions.

Eckstrom, C. V.↗
NASA NTRS1986

Analytical observations on the aerodynamics of a delta wing with leading edge flaps

The effect of a leading edge flap on the aerodynamics of a low aspect ratio delta wing is studied analytically. The separated flow field about the wing is represented by a simple vortex model composed of a conical straight vortex sheet and a concentrated vortex. The analysis is carried out in the cross flow plane by mapping the wing trace, by means of the Schwarz-Christoffel transformation into the real axis of the transformed plane. Particular attention is given to the influence of the angle of attack and flap deflection angle on lift and drag forces. Both lift and drag decrease with flap deflection, while the lift-to-drag ratioe increases. A simple coordinate transformation is used to obtain a closed form expression for the lift-to-drag ratio as a function of flap deflection. The main effect of leading edge flap deflection is a partial suppression of the separated flow on the leeside of the wing. Qualitative comparison with experiments is presented, showing agreement in the general trends.

Oh, S.↗
NASA NTRS1985

A theory for lateral wing-tip blowing

The concept of lateral blowing consists in utilizing thin jets of air, which are ejected in the spanwise direction from slots at the tips of straight and swept wings, or along the leading edges of delta wings, to generate aerodynamic forces without the assistance of deflecting solid surfaces. For weak intensities of blowing the so-generated forces could be used for roll and lateral control of aircraft. In this work a theory for this concept as applied to straight wings is presented, revealing the analytical relationship between blowing and aerodynamic forces. The approach is based on perturbing the span of an elliptically loaded wing. Scaling laws involving blowing intensity, aspect ratio, and angle of attack are derived and compared with experiments. It is concluded that this concept has potential as a novel roll and lateral control device.

Tavella, D.↗
NASA NTRS1986

Flight control system development and flight test experience with the F-111 mission adaptive wing aircraft

The wing on the NASA F-111 transonic aircraft technology airplane was modified to provide flexible leading and trailing edge flaps. This wing is known as the mission adaptive wing (MAW) because aerodynamic efficiency can be maintained at all speeds. Unlike a conventional wing, the MAW has no spoilers, external flap hinges, or fairings to break the smooth contour. The leading edge flaps and three-segment trailing edge flaps are controlled by a redundant fly-by-wire control system that features a dual digital primary system architecture providing roll and symmetric commands to the MAW control surfaces. A segregated analog backup system is provided in the event of a primary system failure. This paper discusses the design, development, testing, qualification, and flight test experience of the MAW primary and backup flight control systems.

Larson, R. R.↗