Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Shape”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Full Coverage Shaped Hole Film Cooling in an Accelerating Boundary Layer with High Free-Stream Turbulence

Full coverage shaped-hole film cooling and downstream heat transfer measurements have been acquired in the accelerating flows over a large cylindrical leading edge test surface. The shaped holes had an 8° lateral expansion angled at 30° to the surface with spanwise and streamwise spacings of 3 diameters. Measurements were conducted at four blowing ratios, two Reynolds numbers and six well documented turbulence conditions. Film cooling measurements were acquired over a four to one range in blowing ratio at the lower Reynolds number and at the two lower blowing ratios for the higher Reynolds number. The film cooling measurements were acquired at a coolant to free-stream density ratio of approximately 1.04. The flows were subjected to a low turbulence condition (Tu = 0.7%), two levels of turbulence for a smaller sized grid (Tu = 3.5%, and 7.9%), one turbulence level for a larger grid (8.1%), and two levels of turbulence generated using a mock aero-combustor (Tu = 9.3% and 13.7%). Turbulence level is shown to have a significant influence in mixing away film cooling coverage progressively as the flow develops in the streamwise direction. Effectiveness levels for the aero-combustor turbulence condition are reduced to as low as 20% of low turbulence values by the furthest downstream region. The film cooling discharge is located close to the leading edge with very thin and accelerating upstream boundary layers. Film cooling data at the lower Reynolds number, show that transitional flows have significantly improved effectiveness levels compared with turbulent flows. Downstream effectiveness levels are very similar to slot film cooling data taken at the same coolant flow rates over the same cylindrical test surface. However, slots perform significantly better in the near discharge region. These data are expected to be very useful in grounding computational predictions of full coverage shaped hole film cooling with elevated turbulence levels and acceleration. IR measurements were performed for the two lowest turbulence levels to document the spanwise variation in film cooling effectiveness and heat transfer.

20 FOSSIL-FUELED POWER PLANTS↗

Resistively heated shape memory polymer device

A resistively heated shape memory polymer device is made by providing a rod, sheet or substrate that includes a resistive medium. The rod, sheet or substrate is coated with a first shape memory polymer providing a coated intermediate unit. The coated intermediate unit is in turn coated with a conductive material providing a second intermediate unit. The second coated intermediate unit is in turn coated with an outer shape memory polymer. The rod, sheet or substrate is exposed and an electrical lead is attached to the rod, sheet or substrate. The conductive material is exposed and an electrical lead is attached to the conductive material.

36 MATERIALS SCIENCE↗

Post polymerization cure shape memory polymers

This invention relates to chemical polymer compositions, methods of synthesis, and fabrication methods for devices regarding polymers capable of displaying shape memory behavior (SMPs) and which can first be polymerized to a linear or branched polymeric structure, having thermoplastic properties, subsequently processed into a device through processes typical of polymer melts, solutions, and dispersions and then crossed linked to a shape memory thermoset polymer retaining the processed shape.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Resistively heated shape memory polymer device

A resistively heated shape memory polymer device is made by providing a rod, sheet or substrate that includes a resistive medium. The rod, sheet or substrate is coated with a first shape memory polymer providing a coated intermediate unit. The coated intermediate unit is in turn coated with a conductive material providing a second intermediate unit. The second coated intermediate unit is in turn coated with an outer shape memory polymer. The rod, sheet or substrate is exposed and an electrical lead is attached to the rod, sheet or substrate. The conductive material is exposed and an electrical lead is attached to the conductive material.

Marion, III, John E.↗

Plant-Based, Shape-Memory Material Could Replace Today’s Conductors

A novel approach that creates a renewable, leathery material—programmed to remember its shape—may offer a low-cost alternative to conventional conductors for applications in sensors and robotics. To make the bio-based, shape-memory material, Oak Ridge National Laboratory scientists streamlined a solvent-free process that mixes rubber with lignin—the by-product of woody plants used to make biofuels. They fashioned the leathery material into small strips and brushed on a thin layer of silver nanoparticles to activate electrical conductivity. The strips were stretched or curled and then frozen as part of the process to program the material to return to its intended shape, which occurs after the application of low heat. “The performance of this polymer can be tuned further,” said ORNL’s Amit Naskar. “Variant lignins can be used at different ratios, which determines the material’s pliability.” This research was sponsored by the Department of Energy’s Bioenergy Technologies Office.

15 GEOTHERMAL ENERGY↗

Multipactor Simulation in SC Elliptical Shape Cavities

Typically multipactor exists near equator region in elliptical shape superconductive cavities. If the multipactor power zone dose not coincide with operating power, it is often the cavity has to pass through it before it reaches operating leve l of field. Results of multipactor simulations for several shapes of elliptical cavity are presented. New shape, which significantly suppresses multipactor, is found.

43 PARTICLE ACCELERATORS↗

Momentum preserving film-cooling shaped holes

A system for cooling includes a surface to be cooled and at least one film-cooling hole within the surface for allowing a film cooling jet of coolant to reach the surface, each of the at least one film-cooling hole having a diameter. The at least one film-cooling hole is shaped to preserve momentum of the coolant and assist in preventing entrainment of the hot gases. A method of cooling a surface proximate hot gas includes providing coolant through a w-shaped film-cooling hole to form a cool film between the hot gas and the surface and preserving momentum of the coolant using the w-shaped film-cooling hole to assist in preventing entrainment of the hot gases.

Shih, Tom I-P↗

Resistively heated shape memory polymer device

A resistively heated shape memory polymer device is made by providing a rod, sheet or substrate that includes a resistive medium. The rod, sheet or substrate is coated with a first shape memory polymer providing a coated intermediate unit. The coated intermediate unit is in turn coated with a conductive material providing a second intermediate unit. The second coated intermediate unit is in turn coated with an outer shape memory polymer. The rod, sheet or substrate is exposed and an electrical lead is attached to the rod, sheet or substrate. The conductive material is exposed and an electrical lead is attached to the conductive material.

Marion, III, John E.↗

Glass or metal forming mold of adjustable shape

A system for shaping glass or metal sheets or panels for use in solar collectors or microwave antennae may include an oven and an adjustable mold. The adjustable mold may comprise a molding surface located within the oven. The molding surface may be coupled to position actuators located outside of the oven via coupling elements. A sheet or panel may be placed in the oven and heated until the sheet or panel softens and takes the shape of the molding surface. The molding surface may be adjusted to achieve different shapes for glass or metal sheets or panels.

42 ENGINEERING↗

Shaped cutting tool

A cutting tool for forming a finished part from a rotating workpiece includes a first cutting edge extending from a first end of the cutting tool, a second cutting edge extending from a second end of the cutting tool, and a shaping edge disposed between the first cutting edge and the second cutting edge. The first cutting edge is operable to remove a trailing end of the rotating workpiece and the second cutting edge is operable to remove a working portion of the rotating workpiece disposed between the trailing end and a leading end. The shaping edge is operable to shape the working portion of the rotating workpiece by advancing the cutting tool into the rotating workpiece until the first cutting edge removes the trailing end of the rotating workpiece and the second cutting edge removes the working portion of the rotating workpiece to form the finished part.

42 ENGINEERING↗

Vibrational sum frequency generation using shaped near infrared light

A vibrational sum frequency generation spectroscopy system with pulse shaping is provided. The pulse shaping provides tunable NIR-Shaped light pulses based on user input parameters which may be specified to customize the system for different experimental and testing conditions or needs.

42 ENGINEERING↗

Systems, devices and methods for communicating data over circularly pulse-shaped waveforms

Circularly pulse-shaped waveforms for communication systems are disclosed herein, including a single carrier modulation in which pulse-shaping is performed using a circular convolution by the transmitter for various modulation schemes. A transmitter, related method, and corresponding receiver are also disclosed for demodulation of the single carrier circularly pulse-shaped signal and data extraction.

42 ENGINEERING↗

A New Shape Optimization Approach for Lightweighting Electric Machines Inspired by Additive Manufacturing: Preprint

Minimizing the mass in electric machines while maintaining superior performance is a new requirement for the advancement of drivetrains used in wind energy and electric mobility. Topology optimization (TO) for lightweighting electric machines using traditional approaches typically explores a restricted design space allowed by standard parametrizable geometry and manufacturing, while advanced methods, such as cell-based density approaches, suffer from a lack of robust manufacturability constraints during the optimization process. To overcome these drawbacks, we explore a grid-independent, boundary TO where the outer shape of the magnet is parameterized using Bezier curves. We conduct a design of experiments (DOE) to study the effect of different magnet shapes on machine performance by varying the control points on the Bezier curves. A machine-learning-based surrogate model is constructed using the data from the DOE to quantify the relationship between the control points, air-gap torque, and mass. The control points are then optimized to maximize the torque density. The approach is used for minimizing electrical steel mass in the International Energy Agency (IEA) 15-MW radial flux direct-drive wind turbine generator. The free-form boundary TO resulted in smooth and concise shapes that can be easily additively manufactured with up to a 20-ton reduction in electrical steel mass.

additive manufacturing↗

Post polymerization cure shape memory polymers

This invention relates to chemical polymer compositions, methods of synthesis, and fabrication methods for devices regarding polymers capable of displaying shape memory behavior (SMPs) and which can first be polymerized to a linear or branched polymeric structure, having thermoplastic properties, subsequently processed into a device through processes typical of polymer melts, solutions, and dispersions and then crossed linked to a shape memory thermoset polymer retaining the processed shape.

Wilson, Thomas S.↗

Shaped cutting tool and method of use to efficiently form a finished part

A method of efficiently forming a finished part, the method includes providing a cutting tool having a first cutting edge extending from a first end of the cutting tool, a second cutting edge extending from a second end of the cutting tool, and a shaping edge disposed between the first cutting edge and the second cutting edge. The cutting tool is advanced into a rotating workpiece such that the first cutting edge removes a trailing end of the rotating workpiece, the shaping edge shapes a working portion of the rotating workpiece, and the second cutting edge removes the working portion of the rotating workpiece to form the finished part.

Ripley, Edward B.↗

Oak Ridge environmental information system (OREIS): formalizing the shapes of things on the Oak Ridge Reservation - 15393

As representations of object and area boundaries on Earth's surface, shapes are important components of geographic information system platforms. The US Department of Energy Office of Environmental Management in Oak Ridge, Tennessee recognizes the importance of shapes as boundary representations and has mandated the Oak Ridge Environmental Information System as the official repository of all geographic information system shapes related to CERCLA cleanup on the Oak Ridge Reservation. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Method of making an annular radioisotope target having a helical coil-shaped foil ribbon between cladding tubes

An annular radioisotope target and method therefor that includes an inner cladding tube and a helical coil-shaped foil ribbon disposed over the inner cladding tube. The helical coil-shaped foil ribbon has a first end, a second end, a first edge and a second edge. An outer cladding tube is disposed over the helical coil-shaped foil ribbon and inner cladding tube, and end caps are attached to the outer cladding tube and the inner cladding tube.

Ripley, Edward B.↗

Methods of forming near-net shape structures from non-stoichiometric oxides

A method of forming a near-net shape structure comprises forming a structure comprising non-stoichiometric metal oxide comprising at least one metal and less than a stoichiometric amount of oxygen, and electrochemically reducing the non-stoichiometric metal oxide in an electrochemical cell to form a structure having a near-net shape and comprising the at least one metal having less than about 1,500 ppm oxygen. Related methods of forming a non-stoichiometric metal oxide by sintering, annealing, or additive manufacturing, and forming a near-net shape structure from the non-stoichiometric metal oxide, as well as related electrochemical cells are also disclosed.

Tripathy, Prabhat K.↗