Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SIZE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Pore size distribution and methane equilibrium conditions at Walker Ridge Block 313, northern Gulf of Mexico

Coexistence of three methane phases (liquid (L), gas (G), hydrate (H)) in marine gas hydrate systems may occur according to in-situ pressure, temperature, salinity and pore size. In sediments with salinity close to seawater, a discrete zone of three-phase (3P) equilibrium may occur near the base of the regional hydrate stability zone (RHSZ) due to capillary effects. The existence of a 3P zone influences the location of the bottom-simulating reflection (BSR) and has implications for methane fluxes at the base of the RHSZ. We studied hydrate stability conditions in two wells, WR313-G and WR313-H, at Walker Ridge Block 313 in the northern Gulf of Mexico. We determined pore size distributions (PSD) by constructing a synthetic nuclear magnetic resonance (NMR) relaxation time distribution. Correlations were obtained by non-linear regression on NMR, gamma ray, and bulk density logs from well KC-151 at Keathley Canyon. The correlations enabled construction of relaxation time distributions for WR313-G and WR313-H, which were used to predict PSD through comparison with mercury injection capillary pressure measurements. With the computed PSD, L+H and L+G methane solubility was determined from in-situ pressure and temperature. The intersection of the L+G and L+H curves for various pore sizes allowed calculation of the depth range of the 3P equilibrium zone. As in previous studies at Blake Ridge and Hydrate Ridge, the top of the 3P zone moves upwards with increasing water depth and overlies the bulk 3P equilibrium depth. In clays at Walker Ridge, the predicted thickness of the 3P zone is approximately 35 m, but in coarse sands it is only a few meters due to the difference in absolute pore sizes and the width of the PSD. The thick 3P zone in the clays may explain in part why the BSR is only observed in the sand layers at Walker Ridge, although other factors may influence the presence or absence of a BSR.

Bihani, Abhishek↗

Cooperative storage of shared files in a parallel computing system with dynamic block size

Improved techniques are provided for parallel writing of data to a shared object in a parallel computing system. A method is provided for storing data generated by a plurality of parallel processes to a shared object in a parallel computing system. The method is performed by at least one of the processes and comprises: dynamically determining a block size for storing the data; exchanging a determined amount of the data with at least one additional process to achieve a block of the data having the dynamically determined block size; and writing the block of the data having the dynamically determined block size to a file system. The determined block size comprises, e.g., a total amount of the data to be stored divided by the number of parallel processes. The file system comprises, for example, a log structured virtual parallel file system, such as a Parallel Log-Structured File System (PLFS).

97 MATHEMATICS AND COMPUTING↗

Method for producing size selected particles

The invention provides a system for preparing specific sized particles, the system comprising a continuous stir tank reactor adapted to receive reactants; a centrifugal dispenser positioned downstream from the reactor and in fluid communication with the reactor; a particle separator positioned downstream of the dispenser; and a solution stream return conduit positioned between the separator and the reactor. Also provided is a method for preparing specific sized particles, the method comprising introducing reagent into a continuous stir reaction tank and allowing the reagents to react to produce product liquor containing particles; contacting the liquor particles with a centrifugal force for a time sufficient to generate particles of a predetermined size and morphology; and returning unused reagents and particles of a non-predetermined size to the tank.

36 MATERIALS SCIENCE↗

HIGH-ENERGY X-RAY PINHOLE CAMERA FOR HIGH-RESOLUTION ELECTRON BEAM SIZE MEASUREMENTS

The Advanced Photon Source (APS) is developing a multi-bend achromat (MBA) lattice based storage ring as the next major upgrade, featuring a 20-fold reduction in emittance. Combining the reduction of beta functions, the electron beam sizes at bend magnet sources may be reduced to reach 5 – 10 µm for 10% vertical coupling. The x-ray pinhole camera currently used for beam size monitoring will not be adequate for the new task. By increasing the operating photon energy to 120 – 200 keV, the pinhole camera’s resolution is expected to reach below 4 µm. The peak height of the pinhole image will be used to monitor relative changes of the beam sizes and enable the feedback control of the emittance. We present the simulation and the design of a beam size monitor for the APS storage ring.

Yang, B.↗

Synthesis of large surface area nano-sized BiVO{sub 4} by an EDTA-modified hydrothermal process and its enhanced visible photocatalytic activity

In this work, monoclinic scheelite-type BiVO{sub 4} nanoparticle with large surface area has been successfully synthesized, using Bi(NO{sub 3}){sub 3} and NH{sub 4}VO{sub 3} as raw materials, through a hydrothermal process in the presence of ethylene diamine tetraacetic acid (EDTA). It is demonstrated that the nanoparticle size of as-prepared BiVO{sub 4} becomes small by decreasing hydrothermal temperature, shortening hydrothermal reaction time and increasing EDTA amount used. The resulting BiVO{sub 4} nanoparticle with large surface area exhibits a good photocatalytic performance for degrading phenol solution as a model organic pollutant under visible illumination. The key of this method is the chelating role of EDTA group in the synthetic process that it can greatly control the concentration of Bi{sup 3+}, leading to the growth inhibition of BiVO{sub 4} crystallite. The work provides a route for the synthesis of Bi-containing nano-sized composite oxides with large surface area. - Graphical abstract: High visible active nano-sized BiVO{sub 4} photocatalyst with large surface area is successfully synthesized, which is attributed to the chelating role of EDTA group inhibiting the growth of BiVO{sub 4} crystallites. Highlights: > Monoclinic scheelite-type BiVO{sub 4} nanoparticle with large surface area has been synthesized by a hydrothermal process. > Key of this method is the chelating role of EDTA group inhibiting the growth of BiVO{sub 4} crystallites. > Resulting nano-sized BiVO{sub 4} exhibits a good photocatalytic activity for degrading phenol under visible illumination.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthetic methods for crystallite size control of bimetallic polyanionic battery compositions

Bimetallic polyanionic materials, such as silver vanadium phosphorus oxide (Ag 2 VO 2 PO 4 , SVOP), are promising cathode materials for Li batteries due in part to their large capacity and high current capability. A new synthesis of Ag 2 VO 2 PO 4 based on microwave heating is disclosed, where the reaction time is reduced by approximately 100 times relative to other reported methods, and the crystallite size is controlled via synthesis temperature, showing a linear positive correlation of crystallite size with temperature. Reaction times of an hour or less are sufficient to render phase-pure material after reaction at 50° C. to 180° C., significantly lower than the temperatures reported for other methods. Crystallite sizes between 42 nm and 60 nm are achieved by the novel method, smaller than by other methods. Silver/vanadium atomic ratios of 1.96 to 2.04 in the as-synthesized SVOP result and appear temperature-dependent. Notably, under galvanostatic reduction, the Ag 2 VO 2 PO 4 sample with the smallest crystallite size delivers the highest capacity and shows the highest loaded voltage.

Takeuchi, Kenneth J.↗

The Effect of Grain Size and Phosphorous-doping of Polycrystalline 3C-SiC on Infrared Reflectance Spectra

The effect of P-doping and grain size of polycrystalline 3C-SiC on the infrared reflectance spectra is reported. The relationship between grain size and full width at half maximum (FWHM) suggest that the behaviour of the 3C-SiC with the highest phosphorous doping level (of 1.2 x 10{sup 19} at. cm{sup -3}) is different from those with lower doping levels (< 6.6 x 10{sup 18} at. cm{sup -3}). It is also further demonstrated that the plasma resonance frequency (w{sub p}) is not influenced by the grain size.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Phonon properties of nanosized MnWO{sub 4} with different size and morphology

Highly hierarchical barlike and flowerlike MnWO{sub 4} microcrystals have been synthesized for the first time by a hydrothermal method, where ethanolamine (EA) and cetyltrimethylamonnium bromide (CTAB) play important roles in directing growth and self-assembly of these structures. The possible formation process has been proposed. In addition, platelike nanosized MnWO{sub 4} was also synthesized by annealing of a precursor obtained by coprecipitation method. The obtained samples were characterized by XRD, SEM, TEM, Raman and IR methods. Raman spectra showed relatively weak dependence on particle size and morphology of the particles. In contrast to this behavior, IR-active bands showed pronounced shifts and changes in relative intensities on particle size and the morphology. Origin of this behavior is discussed. - Graphical Abstract: SEM images of MnWO{sub 4} particles prepared by hydrothermal process at 150 deg. C (left panel) and 200 deg. C (right panel). Highlights: > Hydrothermal synthesis with ethanolamine enables growth of hierarchical nanosized MnWO{sub 4} particles. > Annealing of a precursor obtained by coprecipitation method enables growth of platelike MnWO{sub 4} nanoparticles. > Raman and IR spectra of MnWO{sub 4} nanoparticles depend on both size and morphology of the nanoparticles. > We discuss origin of this behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Size effect of added LaB{sub 6} particles on optical properties of LaB{sub 6}/Polymer composites

Modified LaB{sub 6} particles with sizes ranging from 50 nm to 400 nm were added into polymethyl methacrylate (PMMA) matrix in order to investigate the effect of added LaB{sub 6} particles on optical properties of LaB{sub 6}/PMMA composites. Method of in-situ polymerization was applied to prepare PMMA from raw material-methyl methacrylate (MMA), a process during which LaB{sub 6} particles were dispersed in MMA. Ultraviolet-visible-near infrared (UV-vis-NIR) absorption spectrum was used to study optical properties of the as-prepared materials. The difference in particle size could apparently affect the composites' absorption of visible light around wavelength of 600 nm. Added LaB{sub 6} particles with size of about 70 nm resulted in the best optical properties among these groups of composites. - Graphical abstract: 70 nm LaB{sub 6} particles resulted in the best performance on absorption of VIS and NIR, which could not be apparently achieved by LaB{sub 6} particles beyond nano-scale. Highlights: Black-Right-Pointing-Pointer LaB{sub 6}/PMMA composites were prepared using the method of in-situ polymerization. Black-Right-Pointing-Pointer LaB{sub 6} particles added in MMA prolonged the time needed for its pre-polymerization. Black-Right-Pointing-Pointer Nanosized LaB{sub 6} particles could obviously absorb much NIR but little VIS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ti particle-reinforced surface layers in Al: Effect of particle size on microstructure, hardness and wear

Two types of Ti particles are used in an ultrasonic impact peening (UIP) process to modify sub-surface layers of cp aluminium atomized, with an average size of approx. 20 {mu}m and milled (0.3-0.5 {mu}m). They are introduced into a zone of severe plastic deformation induced by UIP. The effect of Ti particles of different sizes on microstructure, phase composition, microhardness and wear resistance of sub-surface composite layers in aluminium is studied in this paper. The formed layers of a composite reinforced with smaller particles have a highly misoriented fine-grain microstructure of its matrix with a mean grain size of 200-400 nm, while reinforcement with larger particles results in relatively large Al grains (1-2 {mu}m). XRD, SEM, EDX and TEM studies confirm significantly higher particle/matrix bonding in the former case due to formation of a Ti{sub 3}Al interlayer around Ti particles with rough surface caused by milling. Different microstructures determine hardness and wear resistance of reinforced aluminium layers: while higher magnitudes of microhardness are observed for both composites (when compared with those of annealed and UIP-treated aluminium), the wear resistance is improved only in the case of reinforcement with small particles.

36 MATERIALS SCIENCE↗

Influence of particle size and water coverage on the thermodynamic properties of water confined on the surface of SnO2 cassiterite nanoparticles

Inelastic neutron scattering (INS) data for SnO2 nanoparticles of three different sizes and varying hydration levels are presented. Data were recorded on five nanoparticle samples that had the following compositions: 2 nm SnO2*0.82H2O, 6 nm SnO2*0.055H2O, 6 nm SnO2*0.095H2O, 20 nm SnO2*0.072H2O, and 20 nm SnO2*0.092H2O. The isochoric heat capacity and vibrational entropy values at 298 K for the water confined on the surface of these nanoparticles were calculated from the vibrational density of states that were extracted from the INS data. This study has shown that the hydration level of the SnO2 nanoparticles influences the thermodynamic properties of the water layers and, most importantly, that there appears to be a critical size limit for SnO2 between 2 and 6 nm below which the particle size also affects these properties and above which it does not. These results have been compared with those for isostructural rutile-TiO2 nanoparticles [TiO2*0.22H2O and TiO2*0.37H2O], which indicated that water on the surface of TiO2 nanoparticles is more tightly bound and experiences a greater degree of restricted motion with respect to water on the surface of SnO2 nanoparticles. This is believed to be a consequence of the difference in chemical composition, and hence surface properties, of these metal oxide nanoparticles.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

The influence of aluminum grain size on alumina nanoporous structure

An approach to control the interpore distances and nanopore diameters of 150-nm-thick thin aluminum films is reported here. The Al thin films were grown by sputtering on p-type silicon substrate and anodized with a conventional anodization process in a phosphoric acid solution. It was found that interpore distance and pore diameter are related to the aluminum grain size and can be controlled by annealing. The grain contours limit the sizes of alumina cells. This mechanism is valid for grain sizes supporting only one alumina cell and consequently only one pore.

36 MATERIALS SCIENCE↗

Grain size effect on the nonlinear dielectric properties of barium titanate ceramics

The nonlinear dielectric properties of dense BaTiO{sub 3} ceramics with grain size of 1 {mu}m-90 nm were investigated. In the finest ceramics, the permittivity reduces below 1000 and a remarkable nonhysteretic linear dc-tunability [{epsilon}(E)] is obtained at high field, above 40 kV/cm. The observed behavior was explained by considering the nanostructured ceramic as a composite formed by ferroelectric grains, whose nonlinearity is reducing, and by low-permittivity nonferroelectric grain boundaries, whose volume fraction increases when decreasing the grain size. Reducing the grain size in ferroelectric dense materials is an alternative route to accomplish the application requirements: nonhysteretic tunability and permittivity below 1000.

36 MATERIALS SCIENCE↗

Minimum feature size control in level set topology optimization via density fields

A level set topology optimization approach that uses an auxiliary density field to nucleate holes during the optimization process and achieves minimum feature size control in optimized designs is explored. The level set field determines the solid-void interface and the density field describes the distribution of a fictitious porous material using the solid isotropic material with penalization. These fields are governed by two sets of independent optimization variables which are initially coupled using a penalty for hole nucleation. The strength of the density field penalization and projection is gradually increased during the optimization process to promote a 0-1 density distribution. In addition, a second penalty regulates the evolution of the density field in the void phase. The treatment of the density field combined with the second penalty mitigate the appearance of small design features. The minimum feature size of optimized designs is controlled by the radius of the linear filter applied to the density optimization variables. The structural response is predicted by the extended finite element method, the sensitivities by the adjoint method, and the optimization variables are updated by a gradient-based optimization algorithm. Numerical examples investigate the robustness of this approach with respect to algorithmic parameters and mesh refinement. The results show the applicability of the combined density level set topology optimization approach for both optimal hole nucleation and for minimum feature size control in 2D and 3D. This comes, however, at the cost of a more complex problem formulation and additional computational cost due to an increased number of optimization variables.

42 ENGINEERING↗

French Sizing of Medical Devices is not Fit for Purpose

PurposeThe purpose of the study is to quantify the variation in the metric equivalent of French size in a range of medical devices, from various manufacturers, used in interventional radiology.MethodsThe labelling of a range of catheters, introducers, drains, balloons, stents, and endografts was examined. Products were chosen to achieve a broad range of French sizes from several manufacturers. To assess manufacturing accuracy, eight devices were selected for measurement using a laser micrometer. The external diameters of three specimens of each device were measured at centimeter intervals along the length of the device to ensure uniformity.ResultsA total of 200 labels of interventional radiology equipment were scrutinized. The results demonstrate a wide variation in the metric equivalent of French sizing. Labelled products can vary in diameter across the product range by up to 0.79 mm.The devices selected for measurement with the non-contact laser micrometer demonstrate acceptable manufacturing consistency. The external diameter differed by 0.05 mm on average.ConclusionsOur results demonstrate wide variation in the interpretation of the French scale by different manufacturers of medical devices. This has the potential to lead to problems using coaxial systems especially when the products are from different manufacturers. It is recommended that standard labelling should be employed by all manufacturers conveying specific details of the equipment. Given the wide variation in the interpretation of the French scale, our opinion is that this scale either needs to be abandoned or be strictly defined and followed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Crystallite-size dependency of the pressure and temperature response in nanoparticles of magnesia

We have carefully measured the hydrostatic compressibility and thermal expansion for a series of magnesia nanoparticles. We found a strong variance in these mechanical properties as crystallite size changed. For decreasing crystallite sizes, bulk modulus first increased, then reached a modest maximum of 165 GPa at an intermediate crystallite size of 14 nm, and then decreased thereafter to 77 GPa at 9 nm. Thermal expansion, meanwhile, decreased continuously to 70% of bulk value at 9 nm. These results are consistent to nano-ceria and together provide important insights into the thermal-mechanical structural properties of oxide nanoparticles.

36 MATERIALS SCIENCE↗

Effect of Zr Microalloying on Austenite Grain Size of Low-Carbon Steels

The effect of microalloying addition of Zr on the characteristics of inclusions and prior austenite grain sizes following a quench heat treatment has been investigated for two custom-made steels. The average size of particles in the Zr-containing steel is found to be the same as the Zr-free steel (0.49 μm). However, the number of smaller particles in the Zr-containing steel is much higher than the Zr-free steel. The inclusions in the Zr-containing steel are composed of ZrO{sub 2}-TiN-MnS, and inclusions in the Zr-free steel are consisted of TiOx-Ti(C,N). The average prior austenite grain size of the Zr-containing steel is consistently smaller than that of the Zr-free steel, due to a large number of fine oxide inclusions and Ti(C,N) precipitates, working to pin the austenite grain boundaries at temperatures up to 1673 K (1400 °C). The grain refinement mechanisms by inclusions through the addition of Zr are discussed via thermodynamic and kinetic calculations.

36 MATERIALS SCIENCE↗

Spall strength dependence on grain size and strain rate in tantalum

In this paper, we examine the effect of grain size on the dynamic failure tantalum during laser-shock compression and release and identify a significant effect of grain size on spall strength, which is opposite to the prediction of the Hall-Petch relationship because spall is primarily intergranular in both poly and nanocrystalline samples; thus, monocrystals have a higher spall strength than polycrystals, which, in turn, are stronger in tension than ultra-fine grain sized specimens. Post-shock characterization reveals ductile failure which evolves by void nucleation, growth, and coalescence. Whereas in the monocrystal the voids grow in the interior, nucleation is both intra and intergranular in the poly and ultra-fine-grained crystals. The fact that spall is primarily intergranular in both poly and nanocrystalline samples is strong evidence for higher growth rates of intergranular voids, which have a distinctly oblate spheroid shape in contrast with intragranular voids, which are more spherical. The length geometrically-necessary dislocations required to form a grain-boundary (intergranular) void is lower than that of grain-interior (intragranular) void with the same maximum diameter; thus, the energy required is lower. Consistent with prior literature and theory we also identify an increase with spall strength with strain rate from 6x10 6 to 5x10 7 s -1 . Molecular dynamics calculations agree with the experimental results and also predict grain-boundary separation in the spalling of polycrystals as well as an increase in spall strength with strain rate. Finally, an analytical model based on the kinetics of nucleation and growth of intra and intergranular voids and extending the Curran-Seaman-Shockey theory is applied which shows the competition between the two processes for polycrystals.

36 MATERIALS SCIENCE↗