Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Studies on the compositional dependent structural and electrical properties of CaTiO3-modified K0.5Na0.5NbO3 piezoelectric system

Lead-free piezoelectric ceramics of (1 − x)K0.5Na0.5NbO3-xCaTiO3 were fabricated, and their crystal structure, microstructure, and electrical properties were systematically studied. Rietveld refinement of the x-ray diffraction data and Raman spectroscopic analyses revealed a composition-dependent structural phase transition: three phase transitions, namely, from a pure orthorhombic phase for x ≤ 0.02 to a mixed phase of orthorhombic and tetragonal phases (0.03 ≤ x ≤ 0.08) and finally another mixed phase of tetragonal + cubic for x = 0.10 and 0.15 at room temperature (RT). The morphological study reveals a decrease in grain size along with a more uniform distribution of grains as the concentration of CaTiO3 (CT) increases; notably, a homogeneous distribution of grains is observed for x = 0.05. The temperature-dependent dielectric properties show two phase transitions, from orthorhombic to tetragonal (TO-T) and tetragonal to cubic (TC), for unmodified K0.5Na0.5NbO3 (KNN). However, both the phase transition temperatures (TO-T and TC) decrease, and the transition peaks broaden with an increase in CT substitution, and for x > 0.06, the TO-T shifted below RT. The broadening of the transition peak at TO-T may be due to the relaxation behavior. Among the prepared samples, the 5 mol. % CT-modified KNN shows the optimum electrical properties (d33 = 114 pC/N, ɛr = 412, and 2Pr = 15.25 μC/cm2) at RT. The enhanced electrical properties for x = 0.05 are due to the coexistence of orthorhombic and tetragonal phases, facilitating easy polarization rotation and flattening of the free energy profile. A phase diagram has been constructed based on the information gathered from the temperature-dependent dielectric measurements, RT x-ray diffraction, and Raman spectroscopy data and is discussed in detail.

Physics↗
DOE OSTI2018

Modification of eutectic Mg2Si in AlMg5Si2Mn alloy by pre-homogenization deformation treatment with different reduction conditions

Highlights: • PHD treatment was proposed to modify Mg{sub 2}Si morphology of extruded AlMg5Si2Mn alloy. • PHD treatment accelerated spheroidization of eutectic Mg{sub 2}Si in AlMg5Si2Mn alloy. • Tensile properties of AlMg5Si2Mn extrudates were improved by introduction of PHD. - Abstract: The effect of a novel pre-homogenization deformation (PHD) treatment on the microstructure and mechanical properties of extruded AlMg5Si2Mn alloy was investigated. By introducing the cold compression prior to homogenization treatment, the brittle and interconnected eutectic Mg{sub 2}Si phase in the as-cast AlMg5Si2Mn alloy transformed into fine and spherical particles uniformly dispersed in the aluminum matrix. As the amount of PHD increased, up to 10%, the size of the Mg{sub 2}Si particles decreased and their sphericity increased in the extruded samples, resulting in a gradual increase in both strength and elongation after heat treatment. The mechanical properties of the PHD-treated AlMg5Si2Mn extrudates were compared with those of materials prepared using various casting and deformation processes, and the potential application to wrought products was discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A deep learning and finite element approach for exploration of inverse structure–property designs of lightweight hybrid composites

Hybrid composites have important applications, such as high-performance and lightweight materials in aerospace and automotive industries. Hybrid composites utilize the synergy of diverse fillers to achieve desired material properties, but usually have more complicated microstructures. While topology optimization can optimize a particular property, designing hybrid composites for customized mechanical performances, e.g. full-range stress–strain curve, remains challenging. Here, a computational framework that integrated finite element analysis (FEA) and artificial intelligence (AI) methods of Conditional Generative Adversarial Networks (cGAN) deep learning and transfer learning was developed to establish inverse structure–property relationships and design tailor-made hybrid composites. Based on FEA-generated datasets of hybrid fiber-particle–matrix microstructures and their corresponding full-range stress–strain curves, a cGAN architecture was trained to generate tailored microstructures and establish structure–property relationships. Similarity in microstructural features and well-matched stress–strain curves based on the AI-generated composites were achieved. In conclusion, transfer learning was used to expand the pre-trained model for designing different materials systems.

Hybrid composites↗
DOE OSTI2025

Tensile Performance Sensitivity to Variations of Standard 17-4 PH Heat Treatments on LPBF-Produced Material

Standard heat treatments for metals of a particular composition are typically designed with the assumption of a conventional starting microstructure, such as that produced by casting or wrought processing. When applied to metals fabricated by Laser Powder Bed Fusion (LPBF) metal additive manufacturing (AM), these heat treatments can produce inconsistent performance due to the unique as-built microstructures. This study investigates how modifications to standard heat treatments for 17-4 PH steel influence the microstructure and mechanical properties of LPBF-fabricated material. Specimens were produced and subjected to varying solutionizing and homogenizing treatments followed by standard aging treatments. Microstructures were characterized using optical microscopy, Electron Backscatter Diffraction (EBSD), and X-ray diffraction (XRD), and mechanical properties were evaluated through uniaxial tensile testing. Based on these results, recommendations are provided for achieving improved wrought-like performance in LPBF 17-4 PH steel.

17-4 PH↗
DOE OSTI2018

Microstructure, Corrosion and Magnetic Behavior of an Aged Dual-Phase Stainless Steel

In the present work, the effect of the precipitation phenomena on corrosion and magnetic behavior of an aged dual-phase stainless steel was investigated. Aging treatment caused the precipitation of the σ phase, chromium carbides and secondary austenite, which was accompanied by the shifting of the δ/γ interfaces inside the δ ferrite grains. Aging between 700 and 850 °C strongly deteriorated the pitting corrosion resistance of the studied material. Magnetic investigation of the aged material using the vibration sample magnetic technique revealed the sensitivity of the intrinsic magnetic properties to the smallest microstructural change. This was confirmed by the Eddy current technique that led also to the evaluation of the aging-induced localized corrosion.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Additive manufacturing of soft magnetic high entropy alloys: A review

Additive manufacturing (AM) offers unique advantages in fabricating soft magnetic high-entropy alloys (HEAs), enabling precise control over material properties and the development of advanced components for applications such as magnetic cores, electric motors, and transformers. These HEAs exhibit superior magnetic performance, mechanical strength, and thermal stability, making them highly suitable for modern electronics applications. Here, this review explores the advancements in AM-processed soft magnetic HEAs, including ongoing research on process optimization, tailored microstructures, and enhanced magnetic properties. It emphasizes the importance of understanding the correlations between AM process parameters, resulting microstructures, and the soft magnetic properties of HEAs. By summarizing the state of the field, we provide insights into current progress and highlight future research trends, focusing on the potential for industrial adoption and advancements in this emerging area.

36 MATERIALS SCIENCE↗
NASA NTRS2004

Third-Generation TiAl Alloy Tested: Exhibits Promising Properties for Rotating Components

The Revolutionary Turbine Accelerator/Turbine-Based Combined Cycle (RTA/TBCC) Program for the next-generation launch vehicle has targeted gamma titanium aluminide as a potential compressor and structural material. Because of the high compressor inlet and exit temperatures, the TBCC engine requires higher temperature materials than conventional Ti alloys, and because of its stringent thrust-to-weight requirements, the engine requires low-density material to be utilized wherever possible. Third-generation gamma alloys offer higher temperature capability along with low density and high stiffness. A high-temperature, high-strength *-TiAl alloy with a high Nb-content (Gamma MET PX1) was selected for evaluation. The microstructure and mechanical properties of Gamma Met PX (GMPX) in both the as-extruded and a lamellar heat-treated condition and the influence of the microstructure on the tensile, creep, and fatigue properties were investigated in-house.

Draper, Susan L.↗
DOE OSTI2019

Bulk ultrafine grained/nanocrystalline metals via slow cooling

Cooling, nucleation, and phase growth are ubiquitous processes in nature. Effective control of nucleation and phase growth is of significance to yield refined microstructures with enhanced performance for materials. Recent studies reveal that ultrafine grained (UFG)/nanocrystalline metals exhibit extraordinary properties. However, conventional microstructure refinement methods, such as fast cooling and inoculation, have reached certain fundamental limits. It has been considered impossible to fabricate bulk UFG/nanocrystalline metals via slow cooling. Here, we report a new discovery that nanoparticles can refine metal grains to ultrafine/nanoscale by instilling a continuous nucleation and growth control mechanism during slow cooling. The bulk UFG/nanocrystalline metal with nanoparticles also reveals an unprecedented thermal stability. This method overcomes the grain refinement limits and may be extended to any other processes that involve cooling, nucleation, and phase growth for widespread applications.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Effects of Thermomechanical History on the Tensile Behavior of Nitinol Ribbon

Shape memory alloys (SMAs) have enormous potential for a wide variety of applications. A large body of work exists on the characterization of the microstructure and stress-strain behavior of these alloys, Nitinol (NiTi) in particular. However, many attributes of these materials are yet to be fully understood. Previous work at NASA Langley Research Center (LaRC) has included fabrication of hybrid composite specimens with embedded Nitinol actuators and modeling of their thermomechanical behavior. An intensive characterization effort has been undertaken to facilitate fundamental understanding of this alloy and to promote implementation of Nitinol in aerospace applications. Previous work revealed attributes of the Nitinol ribbon that were not easily rationalized with existing data in the literature. In particular, tensile behavior at ambient temperature showed significant dependence on the thermomechanical history prior to testing. The present work is focused on characterizing differences in the microstructure of Nitinol ribbons exposed to four different thermomechanical histories and correlation of the microstructure with tensile properties. Differential scanning calorimetry (DSC) and x-ray diffraction (XRD) analysis were employed to rationalize the microstructures present after exposure to various thermomechanical histories. Three of the Nitinol ribbon conditions were reversible upon heating (in the DSC) through the reverse transformation temperature (A(sub f) to transform the microstructure to austenite. However, the prior thermomechanical conditioning for the Nitinol ribbon that reflected the entire fabrication procedure (4% thermal cycle condition) was found to have an irreversible effect on the microstructure, as it remained unchanged after repeated complete thermal cycles. Tensile tests were conducted to determine the effect of prior thermomechancal conditioning on both the tensile behavior of the Nitinol ribbons and the stress state of the microstructure. The stress-strain behavior of the Nitinol actuators appears to be governed by the interplay between two major variables: namely, microstructural constituents such as the R-phase and the martensite; and the stress state of these constituents (whether twinned with low residual stresses, or detwinned with high residual stresses). The most significant difference in the stress-strain behavior of the four conditions, the critical stress required to achieve an initial stress plateau, was found to depend on both the amount and stress state (twinned or detwinned) of R-phase present in the initial microstructure. Thus, the effect of prior thermomechanical processing is critical to the resulting tensile behavior of the Nitinol actuator. For numerical modeling inputs one must take into account the entire fabrication process on the Nitinol actuator.

Lach, Cynthia L.↗
NASA NTRS1972

Factors affecting the strength of multipass low-alloy steel weld metal

The mechanical properties of multipass high-strength steel weld metals depend upon several factors, among the most important being: (1) The interaction between the alloy composition and weld metal cooling rate which determines the as-deposited microstructure; and (2) the thermal effects of subsequent passes on each underlying pass which alter the original microstructure. The bulk properties of a multipass weld are therefore governed by both the initial microstructure of each weld pass and its subsequent thermal history. Data obtained for a high strength low alloy steel weld metal confirmed that a simple correlation exists between mechanical properties and welding conditions if the latter are in turn correlated as weld cooling rate.

Krantz, B. M.↗
DOE OSTI2018

Effect of Ti on structure and soft magnetic properties of Si-rich Finemet-type nanocrystalline Fe73.5Cu1Nb3-xSi17.5B5Tix alloys

Highlights: • Substitution of Nb by Ti can reduce the T{sub x1} and enlarge the ΔT{sub x}. • Fe{sub 73.5}Cu{sub 1}Nb{sub 2}Si{sub 17.5}B{sub 5}Ti{sub 1} alloy exhibits high μ{sub i} of 18,000 and low H{sub c} of 0.54 Oe. • Magnetic properties were analysed in terms of the relationship between H{sub c} and μ{sub i}. • Soft magnetic properties will deteriorate when Nb is completely replaced by Ti. • The reasons of variation of permeability at high temperature were analyzed. - Abstract: Fe{sub 73.5}Cu{sub 1}Nb{sub 3-x}Si{sub 17.5}B{sub 5}Ti{sub x} (x = 0, 1, 2, 3) amorphous alloys were prepared by the single roller melt spinning method. The effects of Ti substitution for Nb on the crystallization behavior, microstructure and soft magnetic properties were investigated. Compared to the previously reported Finemet alloy, the onset primary crystallization temperature T{sub x1} becomes lower which has dropped from 803K to 758K. The crystallization temperature interval ΔT{sub x} increases from 468K to 488K as the x increases from 0 to 3. However, the Curie temperature of amorphous phase shows a downward tendency with the increase of Ti content. Compared to the previously reported Finemet alloy, the μ{sub i} increases obviously to more than 18,000 at x = 1, the H{sub c} decreases from 0.59 Oe to 0.54 Oe. When Ti replaces Nb completely, the optimum annealing temperature range for precipitating single soft magnetic phase is enlarged, but the permeability at room- and high-temperature is deteriorated, the reason of which was also analysed.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

High Temperature Thermal Barrier Coating Evaluation of Yttrium Aluminum Garnet for Gas Turbine Applications

The Solution Precursor Spray Process (SPPS) process has been shown to overcome the durability and property challenges of applying yttrium aluminum garnet (YAG) coating for high temperature thermal barrier coating (TBC) applications (1200°C+) but only limited testing has been performed in representative application environments. In this study, YAG coatings were developed to optimize microstructure and tailor properties for combustion components in an industrial gas turbine. Thermal conductivity, erosion resistance and furnace cycling durability were used to validate YAG properties against the standard yttria-stabilized zirconia coating (YSZ). Graded and multi-layered microstructures were applied to enhance performance while maintaining durability. Further YAG process development was required to replicate coating properties and optimize deposition on more complex fuel injector nozzle and combustion liner components. Rig testing of both components was performed and compared against the baseline YSZ coating validating the high temperature capability and lower thermal conductivity of the SPPS YAG coating. The components in both tests were cycled for a minimum of ten cycles with the fuel injector test targeting a higher operating temperature while the combustor liner operated at standard conditions. A development engine test is planned to further validate performance in a gas turbine engine of this promising material.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Investigation of structural and magnetic properties of rapidly-solidified iron-silicon alloys at ambient and elevated temperatures

In this work, we investigated the ambient temperature structural properties (~300 K) and the ambient and high temperature (up to 900 K) direct current (DC) magnetic properties of melt-spun Fe-x wt.% Si (x = 3, 5, & 8) alloys. The wheel surface speeds selected for the study were 30 m/s and 40 m/s. The thickness, width, lattice parameter, saturation magnetization (MS), and intrinsic coercivity (HCI) of the melt spun ribbons are presented and compared with data in the literature. The ribbons produced at the lower wheel surface speed (30 m/s) were continuous having relatively uniform edges compared to the ribbons produced at the higher wheel surface speed. The thickness and the width of the melt-spun ribbons ranged between ~15-60 μm and 500-800 μm, respectively. The x-ray diffraction spectra of the melt-spun ribbons indicated the presence of disordered α-phase, irrespective of the composition, and the wheel-surface speed. The lattice parameter decreased gradually as a function of increasing silicon content from ~0.2862 nm (Fe-3 wt.% Si) to ~0.2847 nm (Fe-8 wt.% Si). Wheel surface speed was not shown to have a significant effect on the magnetization, but primarily impacted the ribbon structure. A decreasing trend in the saturation magnetization was observed as a function of increased silicon content. The intrinsic coercivity of the melt-spun alloys ranged between ~50 to 200 A/m. Elevated temperature evaluation of the magnetization in the case of Fe-3 & 5 wt.% Si alloy ribbons was distinctly different from the Fe-8 wt.% Si alloy ribbons. The curves of the as-prepared Fe-3 wt.% Si and Fe-5 wt.% Si alloy ribbons were irreversible while that of Fe-8 wt.% Si was reversible. The MS for any of the combinations of wheel surface speed and composition decreased monotonically with the increase in temperature (from 300 – 900 K). The percentage decrease in MS from 300 K to 900 K for the Fe-3 wt.% Si and Fe-5 wt.% Si alloys was ~19-22 %, while the percentage decrease in the same temperature range for Fe-8 wt.% Si alloy was ~26-30 %. It appears that Fe-3 wt.% Si and Fe-5 wt.% Si alloys ribbons are primarily comprised of the α phase (disordered phase) with any minor constituents being beyond the detection limits of the studies performed, while the Fe-8 wt.% Si alloy ribbons are comprised of disordered and regions of short-range ordering.

Elevated Temperature↗
DOE OSTI2022

Evolution of carbide precipitates in Haynes® 282 superalloy processed by wire arc additive manufacturing

Precipitation hardening regulated with heat treatments is a critical technique for tuning the mechanical properties of Ni-based superalloys fabricated with additive manufacturing, where mechanical deformation is no longer viable for microstructural refinement. As one of the key precipitates, carbides prevail in the additively manufactured alloys, whose precipitation kinetics remain largely vague. This work studies the influence of heat treatments on the evolution of MC- and M 23 C 6 -type carbides within a Haynes® 282 superalloy prepared by wire arc additive manufacturing (WAAM). SEM-EDS analysis was performed to identify the evolution pathways of the carbides, and TEM and XRD characterizations were carried out to track the crystallographic features. The MC-type carbides are originally present in the as-printed alloy, which distribute uniformly across the whole material and remain largely unchanged in size during the heat treatments. By contrast, the incipiently non-existent M 23 C 6 -type carbides precipitate during an aging treatment at 1010 °C, which majorly extend along the grain boundaries as kinetically feasible sites. Further experimental and computational analysis confirms the enhancing effect of the M 23 C 6 -type carbides on the Vickers hardness. For the first time, this work revealed the evolution pathways of carbides within a Haynes® 282 superalloy prepared by WAAM, providing critical information for tunning the microstructure and mechanical properties. Finally, the carbide evolution kinetics established in this work can be potentially extended to other alloys prepared with WAAM, providing critical information to prevent mechanical failures associated with carbide coarsening.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Controlling Solvate Intermediate Growth for Phase-Pure Organic Lead Iodide Ruddlesden–Popper (C 4 H 9 NH 3 ) 2 (CH 3 NH 3 ) n -1 Pb n I 3 n +1 Perovskite Thin Films

The growth of Ruddlesden-Popper perovskite thin films is complicated by the existence of multiple crystallization pathways available to precursors in solution. During conventional thin film growth processes, such as spin-coating or blade-coating, solvents can evaporate too quickly to clearly resolve different reaction intermediates and products that form during crystallization. Here, we resolve multiple reaction products and intermediates that form during Ruddlesden-Popper phase growth by studying drop-cast precursor solutions in situ through the evolution of X-ray diffraction, photoluminescence, and optical micrographs over long timescales in a thin film geometry. We found that methylammonium-rich solvate intermediates play a crucial role in directing the bulk optical properties of the films, and form simultaneously with smaller regions of Ruddlesden-Popper phases during growth. The microstructure and optical properties of these sub-phases were characterized during growth and after annealing, revealing that discrepancies between thin film and single-crystal optical properties originate from solvate intermediates. These lower band-gap solvate-mediated minority phases dominate the optical emission spectrum by means of rapid energy migration, and contribute to sub-band-gap electronic states in photovoltaic devices. Processing routes to yield thin films with optical properties similar to single crystals of Ruddlesden-Popper phases were developed by tuning the precursor stoichiometry and deposition kinetics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Toward Optimizing Electrospun Nanofiber Fuel Cell Catalyst Layers: Polymer–Particle Interactions and Spinnability

We investigate the effect of the poly(acrylic acid) (PAA) carrier polymer concentration on the microstructure and rheological properties of catalyst inks for electrospun polymer–electrolyte membrane fuel-cell catalyst layers. Characterization of an ink microstructure using oscillatory shear rheology showed that the catalyst particles (platinum on carbon) are significantly agglomerated in the absence of PAA or an ionomer. Both the ionomer and PAA promoted the stability of the particles against agglomeration via electrosteric stabilization by adsorbing onto the particle surface. Increasing the PAA concentration increased the stability of the particles (or reduced the agglomerated structure) due to increasing PAA coverage onto the free surface area of the particles. However, beyond a certain increase in concentration, PAA was found to predominantly remain as an excess free polymer in the ink due to an insufficient free/available surface area on the particles for further PAA coverage. Extensional rheology measurements demonstrated that PAA enhances the extensional viscosities of the inks. Consequently, increasing the PAA concentration in the ink promoted the evolution of uniform nanofibers. However, beyond a certain concentration, a significant increase in the shear viscosities of the inks led to defective fiber morphologies because of the onset of flow instabilities. Electrochemical performance comparisons between catalyst layers with different PAA concentrations showed maximum performance at the PAA concentration that led to the least agglomerated structure of the catalyst, most uniform fiber morphologies, and low concentrations of free (non-adsorbing) PAA in the electrode. These results provide a rationale for optimization of electrospun catalyst nanofibers for both spinnability and electrochemical performance.

25 ENERGY STORAGE↗
DOE OSTI2018

Microstructure and Ratcheting Behavior of Additive Manufactured 4043 Aluminum Alloy

In this paper, 4043 aluminum alloy was printed using additive manufacturing (AM) with robot cold metal transfer (CMT) technology. The microstructure and mechanical properties of different parts, including the bottom, middle and upper portions of the printed AM 4043 aluminum alloy, were analyzed. Ratcheting tests were performed using an asymmetric load, and the tensile properties of the pre-ratcheting and un-ratcheted specimens were tested. The results indicate that the dendrites in the middle region are larger than those at the top and bottom regions and that the coarse microstructure associated with the interlayer junction resulted in the decline of the mechanical properties. The tensile strength of the AM specimens is 165 MPa, and the yield strength is 50 MPa. The printed 4043 aluminum alloy exhibits mechanical properties similar to those for conventional cast and welded aluminum alloys. The ratcheting behavior indicates that an increase in the mean stress or stress amplitude leads to an increase in the ratcheting strain, and the accumulation of ratcheting strain causes plastic damage to the materials. Pre-ratcheting behavior causes the tensile and yield strengths to increase compared to the behavior of the un-ratcheted specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Intercritical Annealing Time at Pearlite Dissolution Finish Temperature (Ac{sub 1f}) on Mechanical Properties of Low-Carbon Dual-Phase Steel

The effect of intercritical annealing at Ac{sub 1}, Ac{sub 1f}, and Ac{sub 3} temperatures followed by water quenching was studied on the microstructure and mechanical properties of a 0.035C-0.27Mn low-carbon steel. During short-term holding at Ac{sub 1} and Ac{sub 1f}, some pearlite remained after quenching and the yield-point phenomenon was still detectable, which was related to the formation of small amount of martensite inside pearlite colonies and on ferrite grain boundaries with marginal effect on the surrounding ferrite phase. By increasing holding time at Ac{sub 1f}, pearlite disappeared and DP microstructures were achieved with the disappearance of the yield-point phenomenon and the enhancement of the work-hardening capacity. At long holding times, however, the mechanical properties deteriorated mainly due to the coarsening of martensitic islands and disappearance of dynamic strain aging (Portevin–Le Chatelier) effect at room temperature.

36 MATERIALS SCIENCE↗