Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

P-Type Conduction of ZnO Thin Film by Codoping Technique

Aluminium and zinc target were co-sputtered on silicon (111) substrates using DC magnetron sputtering in the pure argon atmosphere. These films were then underwent the thermal annealing in different ratios of nitrogen and oxygen for 1 hour to form thin oxide films. P-type conduction in ZnO thin films have been realized by the Al-N codoping method, whereby the lowest resistivity of 3.41x10{sup -3} {omega}{center_dot}cm and the highest carrier concentration of 1.54x10{sup 22} cm{sup -3} was achieved for sample prepared at annealed temperature of 300 deg. C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural properties of nitrogenated amorphous carbon films: Influence of deposition temperature and radiofrequency discharge power

The structural properties of nitrogenated amorphous carbon deposited by radiofrequency magnetron sputtering of graphite in pure N{sub 2} plasma are investigated as a function of the substrate temperature and radiofrequency discharge power. The film composition is derived from x-ray photoemission spectroscopy, nuclear reaction analysis and elastic recoil detection measurements and the film microstructure is discussed using infrared, Raman, x-ray photoemission and near edge x-ray absorption fine structure spectroscopic results. At low deposition temperature and low radiofrequency power, the films are soft, porous, and easily contaminated with water vapor and other atmospheric components. The concentration of nitrogen in the films is very large for low deposition temperatures ({approx}33.6 at. % N at 150 deg. C) but decreases strongly when the synthesis temperature increases ({approx}15 at. % N at 450 deg. C). With increasing deposition temperature and discharge power values, the main observed effects in amorphous carbon nitride alloys are a loss of nitrogen atoms, a smaller hydrogen and oxygen contamination related to the film densification, an increased order of the aromatic sp{sup 2} phase, and a strong change in the nitrogen distribution within the carbon matrix. Structural changes are well correlated with modifications of the optical and transport properties.

36 MATERIALS SCIENCE↗

Granular L1{sub 0} FePt:TiO{sub 2} (001) nanocomposite thin films with 5 nm grains for high density magnetic recording

FePt:TiO{sub 2} (001) thin films were deposited on CrRu/MgO underlayers by dc magnetron cosputtering. The effects of TiO{sub 2} content on microstructure and magnetic properties of the epitaxial FePt (001) films were studied. Experimental results showed that even with 20 vol % TiO{sub 2} doping, FePt films could keep a (001) preferred orientation and perpendicular anisotropy. The FePt:TiO{sub 2} (001) film with 5 nm grain size, adjustable coercivity, and reduced exchange coupling was obtained by doping 20 vol % TiO{sub 2} into FePt film, showing great potential as low noise ultrahigh density perpendicular magnetic recording media.

36 MATERIALS SCIENCE↗

Growth and structural characterization of (0.2)Bi(Zn{sub 1/2}Ti{sub 1/2})O{sub 3}-(0.8)PbTiO{sub 3} epitaxial thin films by off-axis rf sputtering

We report the epitaxial growth of ferroelectric (0.2)Bi(Zn{sub 1/2}Ti{sub 1/2})O{sub 3}-(0.8)PbTiO{sub 3} thin films. Despite its high c/a ratio, the off-axis rf magnetron sputtering yields the epitaxial growth of high-quality thin films on (001) SrTiO{sub 3} substrates. The structural development of the film with increasing film thickness has been examined by using the synchrotron x-ray diffraction and x-ray reflectivity. The experimental results can be explained in terms of the strain relaxation process associated with the misfit dislocations between the thin film and the substrate.

36 MATERIALS SCIENCE↗

Local structure of indium oxynitride from x-ray absorption spectroscopy

Synchrotron x-ray absorption near edge structures (XANES) measurements of In L{sub 3} edge is used in conjunction with first principles calculations to characterize rf magnetron sputtered indium oxynitride at different O contents. Good agreement between the measured and the independently calculated spectra are obtained. Calculations show that the XANES spectra of this alloy are sensitive to the coordination numbers of the In atoms, i.e., fourfold for indium nitride-like structures and sixfold for indium oxide-like structures, but not to the substitution of nearest neighbor N by O or vice versa.

36 MATERIALS SCIENCE↗

Effect of thickness on structural, electrical, and electrochemical properties of platinum/titanium bilayer counterelectrode

To strengthen the adhesion of platinum layer to counterelectrodes of dye sensitized solar cells, titanium thin film has been utilized as adhesion layer between platinum and substrate [Wei et al., Appl. Phys. Lett. 90, 153122 (2007)]. In our study, platinum/titanium bilayer counterelectrodes were fabricated by magnetron sputtering. The structural, electrical, and electrochemical properties of the bilayer counterelectrode were studied by varying the thickness of both platinum and titanium layers. The influence of both electrochemical active surface and crystallite size on charge transfer resistance of the bilayer counterelectrode was explored. From these evaluations, it was found that the as-prepared titanium layer was almost amorphous, and intermetallic phase was formed between platinum and titanium layers. As expected, sheet resistance of the electrode decreased with the increase in deposition time of both platinum and titanium layers. Metal titanium was found to be inert in the catalyzing reduction in tri-iodide. With the increment of deposition time of platinum layers, charge transfer resistance of the electrode decreased quickly first, and then reached a plateau after which it changed slightly. This outcome differs from that reported before. Careful examination showed that such a behavior was related closely to the electrochemical active surface area of electrode and platinum crystallite size. For a given electrolyte, charge transfer resistance decreased with the increase in electrochemical active surface and increased with the increment of the latter. Thus, a competition was observed between the two factors, which supports the suggestion of former researchers.

36 MATERIALS SCIENCE↗

Epitaxial growth of aluminum nitride on AlGaN by reactive sputtering at low temperature

We report the synthesis of 1 {mu}m thick single crystalline aluminum nitride films by dc magnetron sputtering on AlGaN/GaN layer grown on sapphire substrate at low temperature (substrate temperature <250 deg. C). The microstructure of c-axis oriented AlN films deposited on Si (100) and AlGaN <0001> substrates was studied by x-ray diffraction, selected area electron diffraction, and transmission electron microscopy. The optimization of process parameters, involving low energetic ion bombardment on film surface (20-30 eV) during the growth, leads to an increase in the surface mobility and thus promotes AlN epitaxial growth on AlGaN substrate at 250 deg. C.

36 MATERIALS SCIENCE↗

Surface morphological evolution during annealing of epitaxial Cu(001) layers

Single crystal Cu(001) layers were grown on MgO(001) by ultrahigh vacuum magnetron sputtering at T{sub s}=100 deg. C. Quantitative surface morphological analyses by in situ scanning tunneling microscopy show that the surfaces exhibit self-affine mound structures with a scaling exponent of 0.82{+-}0.03 and a mound radius r{sub c} that increases from 31{+-}8 to 39{+-}6 nm for increasing layer thickness t=24-120 nm. In situ annealing at 200 and 300 deg. C leads to a thermodynamically driven mass transport that minimizes the surface step density, resulting in broader mounds and a smaller root mean square surface roughness {sigma}. This effect is most pronounced for t=24 nm, for which r{sub c} increases from 31{+-}8 to 70{+-}20 nm and {sigma} decreases from 1.3{+-}0.1 to 0.74{+-}0.08 nm, resulting in a decrease in the average surface slope from {chi}=7 deg. to 2 deg. and an increase in the average terrace width w{sub T} by more than a factor of 4. In contrast, w{sub T} increases by only 20% for t=120 nm. This remarkable difference between 'thin' and 'thick' layers is attributed to diverging surface morphological pathways during annealing: The strong smoothening for t=24 nm is due to a competitive coalescence process where some mounds grow laterally at the expense of their smaller neighbors, which die out. In contrast, the initially wider mounds of thicker layers (t=120 nm) combine to form a quasistable surface morphology that exhibits anisotropic mound structures, which limit mass transport and stabilize the surface step density.

36 MATERIALS SCIENCE↗

Epitaxial nanotwinned Cu films with high strength and high conductivity

We report on the synthesis of epitaxial (single-crystal-like), nanotwinned Cu films via magnetron sputtering. Increasing the deposition rate from 1 to 4 nm/s decreased the average twin lamellae spacing from 16 to 7 nm. These epitaxial nanotwinned Cu films exhibit significantly higher ratio of hardness to room temperature electrical resistivity than columnar grain (nanocrystalline), textured, nanotwinned Cu films.

36 MATERIALS SCIENCE↗

Large pyroelectric effect in undoped epitaxial Pb(Zr,Ti)O{sub 3} thin films on SrTiO{sub 3} substrates

We have studied pyroelectric and ferroelectric properties of Pb(Zr,Ti)O{sub 3} thin films grown epitaxially on SrTiO{sub 3}(001) substrates by rf magnetron sputtering. The pyroelectric coefficient was measured in the temperature range from 280 to 370 K using the Byer-Roundy method. Values as high as 48 nC/cm{sup 2} K have been obtained at 300 K. The PZT thin films exhibited a remanent polarization of 45-58 {mu}C/cm{sup 2}. The improved pyroelectric coefficient was attributed to a high crystalline quality of the films, as revealed by x-ray diffraction that showed only (001)-oriented perovskite PZT phase and a {omega}-rocking curve full width at half maximum value as low as 4.2 arc min for 300 nm thick films.

36 MATERIALS SCIENCE↗

The contribution of grain boundary barriers to the electrical conductivity of titanium oxide thin films

Titanium oxide thin films were prepared by reactive magnetron sputtering. The reactive gas pulsing process was implemented to control the oxygen injection in the deposition process and, consequently, to tune the oxygen concentration in the films from pure titanium to stoichiometric TiO{sub 2}, maintaining a homogeneous in-depth concentration. The electrical conductivity of the films was investigated as a function of the oxygen injection time, the metalloid concentration and temperature, in the range 90-600 K. The curved Arrhenius plots of the conductivity were examined taking into account the grain boundary limited transport model of Werner (J. H. Werner [Solid State Phenom. 37-38, 213 (1994)]). The grain barrier heights were found to depend significantly on the oxygen supplied into the deposition process and thus, on the oxygen-to-titanium atomic ratio in the films. The analysis as a function of temperature showed that the conduction mechanism in the coatings was not solely limited by the oxygen-to-titanium atomic ratio, but also by the grain boundary scattering.

36 MATERIALS SCIENCE↗

High performance indium gallium zinc oxide thin film transistors fabricated on polyethylene terephthalate substrates

High-performance amorphous ({alpha}-) InGaZnO-based thin film transistors (TFTs) were fabricated on flexible polyethylene terephthalate substrates coated with indium oxide (In{sub 2}O{sub 3}) films. The InGaZnO films were deposited by rf magnetron sputtering with the presence of O{sub 2} at room temperature. The n-type carrier concentration of InGaZnO film was {approx}2x10{sup 17} cm{sup -3}. The bottom-gate-type TFTs with SiO{sub 2} or SiN{sub x} gate dielectric operated in enhancement mode with good electrical characteristics: saturation mobility 11.5 cm{sup 2} V{sup -1} s{sup -1} for SiO{sub 2} and 12.1 cm{sup 2} V{sup -1} s{sup -1} for SiN{sub x} gate dielectrics and drain current on-to-off ratio >10{sup 5}. TFTs with SiN{sub x} gate dielectric exhibited better performance than those with SiO{sub 2}. This is attributed to the relatively high dielectric constant (i.e., high-k material) of SiN{sub x}. After more than 500 h aging time at room temperature, the saturation mobility of the TFTs with SiO{sub 2} gate dielectric was comparable to the as-fabricated value and the threshold voltage shift was 150 mV.

36 MATERIALS SCIENCE↗

Ferroelectric stripe domains in PbTiO{sub 3} thin films: Depolarization field and domain randomness

Observation of stripe domains in PbTiO{sub 3} thin films using standard x-ray diffraction analysis at room temperature is discussed. High-quality c-axis oriented thin films of varying thickness, from 6 to 210 unit cells, were grown on buffered NH{sub 4}-HF etched SrTiO{sub 3}(001) and Nb:SrTiO{sub 3}(001) substrates using off-axis radio frequency magnetron sputtering. High-resolution linear Q{sub x} scans reveal a superstructure around the specular Bragg peaks, consistent with the presence of ferroelectric stripe domains. For thin samples, the stripe width is found to be proportional to the square root of the film thickness, with random in-plane orientation of domains. For films with a thickness of more than {approx}100 unit cells, both monodomain samples and stripe domains were observed. We present evidence for the presence of a threshold depolarization field, above which there is a monotonically decreasing relationship between the domain width and the depolarization field. Furthermore, simulations show that random variations in size of the domains affect the separation of the diffuse scattering peaks from that of the specular reflection.

36 MATERIALS SCIENCE↗

Interfacial and electrical properties of SrBi{sub 2}Ta{sub 2}O{sub 9}/ZrO{sub 2}/Si heterostructures for ferroelectric memory devices

We have investigated the interfacial and frequency dependent electrical properties of metal-ferroelectric-insulator-semiconductor capacitors with SrBi{sub 2}Ta{sub 2}O{sub 9} (SBT) ferroelectric films grown on ZrO{sub 2} buffer layer coated Si. Heterostructure SBT and ZrO{sub 2} thin films were deposited using rf magnetron sputtering. Interfacial and surface roughness parameters of heterostructures were extracted from the simulation of specular x-ray reflectivity data. The structure exhibited clockwise capacitance-voltage hysteresis with a maximum memory window of 2.0 V at a bias voltage of {+-}7 V. Frequency dependent (5 kHz-1 MHz) measurements at room temperature indicated that the clockwise hysteresis originates from the ferroelectric domain reversal. A minimum leakage current density of 4x10{sup -8} A/cm{sup 2} of fabricated capacitors at an applied voltage of {+-}5 V revealed that the ZrO{sub 2} buffer layer prevents the interfacial diffusion between SBT thin film and the substrate, resulting in an improvement of interface quality. The charge retention time of the ferroelectric capacitor was studied as a function of buffer layer thickness.

36 MATERIALS SCIENCE↗

Two-Slotted Surface Coil Array for Magnetic Resonance Imaging at 4 Tesla

Arrays of antennas have been widely accepted for magnetic resonance imaging applications due to their high signal-to-noise ratio (SNR) over large volumes of interest. A new surface coil based on the magnetron tube and called slotted surface coil, has been recently introduced by our group. This coil design experimentally demonstrated a significant improvement over the circular-shaped coil when used in the receive-only mode. The slotted coils formed a two-sheet structure with a 90 deg. separation and each coil had 6 circular slots. Numerical simulations were performed using the finite element method for this coil design to study the behaviour of the array magnetic field. Then, we developed a two-coil array for brain magnetic resonance imaging to be operated at the resonant frequency of 170 MHz in the transceiver mode. Phantom images were acquired with our coil array and standard pulse sequences on a research-dedicated 4 Tesla scanner. Numerical simulations demonstrated that electromagnetic interaction between the coil elements is negligible, and that the magnetic field showed a good uniformity. In vitro images showed the feasibility of this coil array for standard pulses for high field magnetic resonance imaging.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Effect of structural anisotropy on electronic conduction in delafossite tin doped copper indium oxide thin films

Sn doped CuInO{sub 2} thin films having a single delafossite phase have been synthesized by magnetron sputtering technique. A gradual decrease in the activation energy from 0.43 to about 0.10 eV and a large increase in conductivity are observed in Sn doped samples with increasing fraction of crystallites having (006) orientation due to an increase in substrate temperature. Due to thermally activated carrier transport along O-A-O layers and activated carrier generation along BO{sub 6} layers, crystallite orientation becomes a crucial factor in controlling the conduction in delafossite thin films.

36 MATERIALS SCIENCE↗

Excitation of parasitic modes in gyrotrons with fast voltage rise

Megawatt-class, long-pulse and continuous-wave gyrotrons operate in high-order modes in order to handle the thermal losses in the resonators. The spectral density of neighboring modes in these devices is high; consequently during the beam voltage rise parasitic modes can be excited. If such gyrotrons are used in plasma experiments, these parasites can be dangerous for the receiving channels of numerous diagnostic tools. It is shown that in gyrotrons utilizing diode-type magnetron injection guns the shortening of the voltage rise time to about one microsecond can practically eliminate excitation of parasitic modes even in devices with a 2 MW power level. Some means for realizing such rise times in high-voltage modulators which can be used for megawatt-class gyrotrons are discussed. It is also shown that allowable beam voltage overshoot in such gyrotrons is about 2.5%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interface as the origin of ferromagnetism in cobalt doped ZnO film grown on silicon substrate

We have investigated the magnetic properties of Co-doped zinc oxide (ZnO) film deposited on silicon substrate by magnetron sputtering. Co ions have a valence of 2+ and substitute for Zn sites in the lattice. By using a chemical etching method, an extrinsic ferromagnetism was demonstrated. The observed ferromagnetism is neither associated with magnetic precipitates nor with contamination, but originates from the silicon/silicon oxide interface. This interface ferromagnetism is characterized by being temperature independent and by having a parallel magnetic anisotropy.

36 MATERIALS SCIENCE↗