SEARCH · Engineering Papers

Results for “Liquid Extraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

All sources NASA NTRS DOE OSTI

DOE OSTI2017

Delocalization and stretch-bend mixing of the HOH bend in liquid water

Liquid water’s rich sub-picosecond vibrational dynamics arise from the interplay of different high- and low-frequency modes evolving in a strong yet fluctuating hydrogen bond network. Recent studies of the OH stretching excitations of H 2 O indicate that they are delocalized over several molecules, raising questions about whether the bending vibrations are similarly delocalized. In this paper, we take advantage of an improved 50 fs time-resolution and broadband infrared (IR) spectroscopy to interrogate the 2D IR lineshape and spectral dynamics of the HOH bending vibration of liquid H2O. Indications of strong bend-stretch coupling are observed in early time 2D IR spectra through a broad excited state absorption that extends from 1500 cm -1 to beyond 1900 cm -1 , which corresponds to transitions from the bend to the bend overtone and OH stretching band between 3150 and 3550 cm -1 . Pump-probe measurements reveal a fast 180 fs vibrational relaxation time, which results in a hot-ground state spectrum that is the same as observed for water IR excitation at any other frequency. The fastest dynamical time scale is 80 fs for the polarization anisotropy decay, providing evidence for the delocalized or excitonic character of the bend. Finally, normal mode analysis conducted on water clusters extracted from molecular dynamics simulations corroborate significant stretch-bend mixing and indicate delocalization of δ HOH on 2-7 water molecules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Post-irradiation examination of optical components for advanced fission reactor instrumentation

The use of optical instrumentation in advanced nuclear fission systems, such as molten salt reactors, liquid metal-cooled reactors, and high-temperature gas-cooled reactors, has the potential to enhance reactor safety and economic performance through in situ and online measurement of reactor conditions. Selection of suitable optical components, such as optical windows and fibers, is essential for operation of optical instrumentation in intense radioactive and thermal environments inherent to nuclear reactor systems. We present the development and performance of a self-contained and mobile post-irradiation examination system for rapid characterization of the optical properties of materials. The instrument combines linear absorption and nanosecond Z-scan modules in a compact, relocatable design. The system mobility allows for the evaluation of optical samples at the site of irradiation, minimizing the delay between extraction from the irradiation site and optical characterization. This provides nearly real-time information on the material performance under simultaneous irradiation and thermal annealing, simulating the relevant conditions for the use of those components in nuclear power systems.

Morgan, Bryan William (ORCID:0000000224668764)↗

DOE OSTI2025

Using Separation-Enhanced Isotope Ratio Mass Spectrometry to Enable Increased Renewable Carbon Content in Transportation Fuels (CRADA 525)

Stable isotope ratio measurements of carbon atoms using isotope ratio mass spectrometry (IRMS) can be an effective tool for quantifying biogenic carbon in co-processed fuels, with results approaching the precision and accuracy of accelerator mass spectrometry (AMS). The lower cost of an IRMS may enable deployment to refineries, improving access and analysis turnaround times (≤2 hours), and, by extension, provide data that can allow process optimization to maximize renewable carbon in desired refinery products. This project explored the integration of chemical separation with IRMS analyses to enable highly detailed tracking of biogenic carbon into fuel product streams separated by boiling point range, chemical class, or specific compound. Forty-nine fuels and fuel components of fossil and biogenic origin, spanning gasoline and diesel boiling point ranges, were received from three refiners and were analyzed for their δ 13 C values via IRMS. Results spanned a 13 C range from ca. 10‰ to 44‰ and reflect materials derived from sustainable sources (e.g., C4 or C3 plants, animal-based pathways, syngas) or from fossil-derived fuels. Common ranges are approximately 18‰ to 9‰ and approximately 30‰ to 20‰ for C4 and C3 plants, respectively, and approximately 34‰ to 24‰ and approximately 70‰ to 33‰ for petroleum-derived fuels and methane, respectively. Fuel-like standards were developed and tested using direct-injection elemental analyzer (EA) IRMS for liquid fuels. This method was compared with the published methods, yielding statistically similar results. Four blend curve sets were produced ranging from 0% to 100% of a fuel containing biogenic carbon, focusing on 0% to 10% biogenic carbon. Linear fits were the most applicable for two of the four blend curve sets; however, two sets were found to exhibit slightly quadratic behavior, which was more pronounced in low biogenic blend samples, necessitating second-order fits. The origin of the slight quadratic behavior remains unclear; however, the discussion points to possible interpretations. CanmetENERGY thoroughly characterized a majority of the samples using one- and two-dimensional gas chromatography (GC and GC×GC, respectively) and other analyses. Selected samples were subjected to solid phase extraction (SPE) for saturate, olefin, aromatic, and polar (SOAP) analysis, and the resulting solvent-diluted fractions containing saturates and aromatics were returned to Pacific Northwest National Laboratory (PNNL), where the solvent was removed via evaporation or physical separation using GC techniques. Characterization and separations provided an understanding of saturate and aromatic content, as well as boiling point ranges for each sample and sample fraction. Samples resulting from SPE were examined using EA-IRMS and gas chromatography combustion IRMS (GC-C-IRMS) analyses. Both approaches suggest that the range in values between end-members can be increased by selecting the paraffinic or aromatic fraction of the end-member or by selecting among individual compounds resulting from GC separation of the paraffinic fractions. Considerable work remains to put these approaches into practice and statistically validate the benefit for using a fraction or individual compound over bulk analysis of a sample. However, initial results suggest that separations provide advantages for samples having blend ratios of less than 10% biogenic blendstocks. 13 C results showed statistically similar biofuel blend results to those obtained at PNNL, although additional work is needed to obtain better reproducibility. Select samples were sent to Los Alamos National Laboratory (LANL) for IRMS measurements and Beta Analytics for AMS measurements. This work suggests that IRMS and AMS yield closely comparable results and in some circumstances, IRMS could serve as a surrogate for AMS. While additional work is needed to better resolve statistical advantages for separations and better show the comparable nature of IRMS and AMS in both the biogenic carbon analysis of bulk chemical classes, initial results from this study suggest that these should be pursued in order to proliferate this approach for quantifying biogenic carbon in transportation fuels to the refinery level, thereby potentially enabling process optimization in co-processing scenarios.

09 BIOMASS FUELS↗

DOE OSTI2021

In situ and operando force-based atomic force microscopy for probing local functionality in energy storage materials

Electrochemical energy storage is the key enabling component of electric vehicles and solar-/wind-based energy technologies. The enhancement of energy stored requires the detailed understanding of charge storage mechanisms and local electrochemical and electromechanical phenomena over a variety of length scales from atoms to full cells. Classical electrochemical techniques, such as voltammetry, represent the macroscopic electrochemical properties, and consequently do not allow to extract important information about local electrochemical reactions, ions adsorption, intercalations, and transport. Understanding, controlling, and tuning the local electrochemical functionalities in functional energy materials require in situ/operando techniques which limit the use of structural and functional characterization techniques that provide local information. Here, force-based atomic force microscopies (AFMs) have provided novel insights into locally probing electrochemical mechanisms on tens of nanometer and even molecular length scales and provide a viable pathway to probe electrochemical processes in situ/operando. In this review, we highlight the contributions in the development and application of force-based AFM methods to elucidate the local charge storage mechanism in a variety of energy-related materials. We will focus in particular on methods or AFM modalities in a liquid electrolyte environment.

25 ENERGY STORAGE↗

DOE OSTI2013

Crystalline Ceramic Waste Forms: Comparison Of Reference Process For Ceramic Waste Form Fabrication

The research conducted in this work package is aimed at taking advantage of the long term thermodynamic stability of crystalline ceramics to create more durable waste forms (as compared to high level waste glass) in order to reduce the reliance on engineered and natural barrier systems. Durable ceramic waste forms that incorporate a wide range of radionuclides have the potential to broaden the available disposal options and to lower the storage and disposal costs associated with advanced fuel cycles. Assemblages of several titanate phases have been successfully demonstrated to incorporate radioactive waste elements, and the multiphase nature of these materials allows them to accommodate variation in the waste composition. Recent work has shown that they can be produced from a melting and crystallization process. The objective of this report is to explore the phase formation and microstructural differences between lab scale melt processing in varying gas environments with alternative densification processes such as Hot Pressing (HP) and Spark Plasma Sintering (SPS). The waste stream used as the basis for the development and testing is a simulant derived from a combination of the projected Cs/Sr separated stream, the Trivalent Actinide - Lanthanide Separation by Phosphorous reagent Extraction from Aqueous Komplexes (TALSPEAK) waste stream consisting of lanthanide fission products, the transition metal fission product waste stream resulting from the transuranic extraction (TRUEX) process, and a high molybdenum concentration with relatively low noble metal concentrations. Melt processing as well as solid state sintering routes SPS and HP demonstrated the formation of the targeted phases; however differences in microstructure and elemental partitioning were observed. In SPS and HP samples, hollandite, pervoskite/pyrochlore, zirconolite, metallic alloy and TiO 2 and Al 2 O 3 were observed distributed in a network of fine grains with small residual pores. The titanate phases that incorporate M +3 rare earth elements were observed to be distinct phases (ex. Nd 2 Ti 2 O 7 with less degree of substitution as compared to the more homogeneous melt processed samples where a high degree of substitution and variation of composition within grains was observed. Liquid phase sintering was enhanced in reducing gas environments and resulted in large (10-200 microns) irregular shaped grains along with large voids associated with the melt process; SPS and HP samples exhibited finer grain size with smaller voids. Metallic alloys were observed in the bulk of the sample for SPS and HP samples, but were found at the bottom of the crucible in melt processed trials. These results indicate that for a first melter trial, the targeted phases can be formed in air by utilizing Ti/TiO 2 additives which aid phase formation and improve the electrical conductivity. Ultimately, a melter run in reducing gas environments would be beneficial to study differences in phase formation and elemental partitioning.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2014

Advanced Automotive Fuels Research, Development, and Commercialization Cluster (OH) (Final Report)

Technical aspects of producing alternative fuels that may eventually supplement or replace conventional the petroleum-derived fuels that are presently used in vehicular transportation have been investigated. The work was centered around three projects: 1) deriving butanol as a fuel additive from bacterial action on sugars produced from decomposition of aqueous suspensions of wood cellulose under elevated temperature and pressure; 2) using highly ordered, openly structured molecules known as metal-organic framework (MOF) compounds as adsorbents for gas separations in fuel processing operations; and 3) developing a photocatalytic membrane for solar-driven water decomposition to generate pure hydrogen fuel. Several departments within the STEM College at YSU contributed to the effort: Chemistry, Biology, and Chemical Engineering. In the butanol project, sawdust was blended with water at variable pH and temperature (150 – 250 °C), and heated inside a pressure vessel for specified periods of time. Analysis of the extracts showed a wide variety of compounds, including simple sugars that bacteria are known to thrive upon. Samples of the cellulose hydrolysate were fed to colonies of Clostridium beijerinckii, which are known to convert sugars to a mixture of compounds, principally butanol. While the bacteria were active toward additions of pure sugar solutions, the cellulose extract appeared to inhibit butanol production, and furthermore encouraged the Clostridium to become dormant. Proteomic analysis showed that the bacteria had changed their genetic code to where it was becoming sporulated, i.e., the bacteria were trying to go dormant. This finding may be an opportunity, as it may be possible to genetically engineer bacteria that resist the butanol-driven triggering mechanism to stop further fuel production. Another way of handling the cellulosic hydrolysates was to simply add the enzymes responsible for butanol synthesis to the hydrolytic extract ex-vivo. These enzymes are generally not available commercially, however, and those that are can be quite expensive. Accordingly, the genes responsible for enzyme synthesis were inserted into other microorganisms in order to accelerate enzyme production. This was demonstrated for two of the required enzymes in the overall series. In the MOF project, a number of new MOF compounds were synthesized and characterized, as well as some common MOFs well-known for their adsorption properties. Selectivity for specific gases such as CO 2 and H 2 was demonstrated, although it was seen that water vapor would frequently act as an interferent. This work underscored the need to test MOF compounds under real world conditions, i.e., room temperature and above instead of liquid N 2 temperature, and testing adsorption using blends of gases instead of pure components. In the solar membrane project, thin films of CdTe and WO 3 were applied to steel substrates and used as p-type and n-type semiconductors, respectively, in the production of H 2 and O 2 . Testing with 2 H and 18 O isotopically labeled water enabled substantiation of net water-splitting.

08 HYDROGEN↗

NASA NTRS2012

Multi-Scale Modeling of Liquid Phase Sintering Affected by Gravity: Preliminary Analysis

A multi-scale simulation concept taking into account impact of gravity on liquid phase sintering is described. The gravity influence can be included at both the micro- and macro-scales. At the micro-scale, the diffusion mass-transport is directionally modified in the framework of kinetic Monte-Carlo simulations to include the impact of gravity. The micro-scale simulations can provide the values of the constitutive parameters for macroscopic sintering simulations. At the macro-scale, we are attempting to embed a continuum model of sintering into a finite-element framework that includes the gravity forces and substrate friction. If successful, the finite elements analysis will enable predictions relevant to space-based processing, including size and shape and property predictions. Model experiments are underway to support the models via extraction of viscosity moduli versus composition, particle size, heating rate, temperature and time.

Olevsky, Eugene↗

DOE OSTI2023

AN ACID BAKING APPROACH TO ENHANCE RARE EARTH ELEMENT RECOVERY FROM BITUMINOUS COAL SOURCES

Rare earth elements (REE) are a group of 17 elements typically classified as light and heavy rare earth elements, which play a crucial role in developing the latest technologies for energy, defense, and medical sectors. Even though REEs have been found in more than 200 minerals, only bastnaesite, monazite and xenotime are commercially exploited for REE extraction. However, the recent exponential increase in REE demand has spurred countries such as the United States into research for the extraction of REEs from secondary sources such as coal, acid mine drainage, and coal ash. Several coal sources (e.g., Fire Clay seam coal) across the United States have been identified to contain elevated concentrations of rare earth elements (>600 ppm), and various researchers have investigated the feasibility of both physical and hydrometallurgical extraction techniques for rare earth concentration and subsequent extraction. However, both physical and direct leaching were concluded to be inefficient for RE beneficiation and extraction due to low recoveries. Alternatively, thermal treatment provides promising means for RE recovery from bituminous coal sources. The positive impact of thermal treatment/calcination was established to be due to the decarbonization and dehydroxylation of the clays, which released entrapped rare earth elements within the dominant minerals and converted them into an acid-soluble form. Nonetheless, the improvement in recovery was limited to the light REEs (LREEs) with an insignificant increase in the heavy REEs (HREE). It was demonstrated that the light and heavy REEs in the material were associated with difficult-to-leach minerals such as monazite, xenotime, and zircon, which were not decomposed by simple calcination due to their high thermal stability. Hence, roasting in the presence of chemicals was necessary to ensure the decomposition of those REE-containing minerals. As such, this study was focused on the acid baking treatment of bituminous coals with an aim to enhance REE recovery, especially HREEs. Based on the presence of REE minerals like monazite and xenotime, three pre-leach treatment methods, i.e., 1) roasting, 2) direct acid baking, and 3) acid baking after roasting were investigated. Roasting tests at 600 ⁰C revealed that the recovery of light REEs (LREEs) was enhanced while the recovery of HREEs remained relatively unaffected. LREE and HREE recovery values of 38.3% and 21.3%, respectively, were achieved using a 50 g/L sulfuric acid solution at 5% solid concentration and a solution temperature of 75 ⁰C for 2 hours. Comparatively, direct acid baking at 250 °C provided substantial increased LREE and HREE recovery values to approximately 49.4% and 53.0%, respectively, using an equivalent acid dosage. Recoveries were maximized to 77.0% and 79.6% for LREE and HREE, respectively, by roasting followed by acid baking. Similar results were obtained from the treatment of a second bituminous coal source. Due to strong correlations between REE and Al recovery values, tests were performed on kaolinite and illite, which were prominent clay minerals within the source coals. These experiments revealed that the REE recovery improvements were likely a result of dehydroxylation of clays and subsequent release and decomposition of REE-bearing minerals such as monazite, xenotime and zircon. Subsequently, a parametric study was conducted to identify the impact of acid baking parameters on rare earth element recovery. The factors investigated using a three-level statistical experimental program were acid baking time, acid solution concentration, baking temperature, and acid solution-to-solids ratio which were found to significantly impact REE and contaminant element (Al, Fe, and Ca) recovery. An increase in baking temperature up to around 250 ⁰C improved the light and heavy REE recovery values by more than 50 absolute percentage points relative to performances achieved when direct leaching. As aforementioned, acid baking was needed to both decompose the clay minerals and liberate the REE minerals, which allowed access for the acid to solubilize the REEs. Acid concentration of the solution used for acid baking was studied as a means of minimizing the amount of acid needed to achieve a target REE recovery. However, thermo-gravimetric and differential scanning calorimetry analysis (TGA-DSC) of sulfuric acid under oxidizing atmosphere revealed that the addition of water decreased the evaporation temperature, which explains the lower REE recovery values obtained when using acid concentrations less than 100%. Using pure sulfuric acid at an acid-to-solid ratio of 0.8:1 resulted in recovery values of around 70% for both LREEs and HREEs. The decomposition reaction time was relatively quick with 65% of the TREEs recovered within the first 10 minutes. Following the identification of optimum operating conditions through the parametric study, a systematic leaching study was carried out to examine the impact of leaching parameters, such as solid-to-liquid (S/L) ratio, temperature, and time, on REE recovery using acid baking conditions of 1:1 acid to solids ratio at 250 °C for 30 minutes. The solid-to-liquid ratio was varied from 1-20% by weight at 25 °C, 50 °C, and 75 °C solution temperatures. The results indicated that reaction time and solution temperature considerably impacted the recovery of heavy and light REEs. Interestingly, LREE recovery reduced from 68% at 5% S/L to 58% at 20%S/L, whereas HREE recovery of 78% remained unaffected. The decrease in the LREE recovery was determined to be due to La and Ce precipitation, likely through isomorphic substitution with calcium in gypsum. The kinetic data indicated that 67% LREE and 77% HREE recovery could be obtained within the first 15 minutes of the reaction, suggesting fast reaction kinetics. Furthermore, raising the solution temperature from 25 °C to 75 °C increased the LREE and HREE recovery from 60% and 32% to 67% and 79%, respectively. The kinetic modeling results demonstrated that the rate-limiting step in the LREE dissolution was diffusion and chemical reaction, whereas the HREE extraction was controlled by only chemical reaction. The leaching study concluded that using 20% S/L at 75 °C for 15 minutes maximized LREE and HREE recovery. The lab-scale precipitation study showed that Fe and Al in solution could be removed at pH 4.5 followed by REE precipitation at pH 6.0 using 6 mol/L NaOH. Finally, the bench-scale data was used to develop a process flowsheet for REE recovery from low-grade bituminous coal sources using acid baking. Finally, based on the proposed flowsheet, a concentrated RE-cake obtained through selective precipitation at pH 6.5 was re-leached using HCl at pH 1.5. The resultant leachate was used to identify the impact of various operating parameters on REE recovery and purity with an aim to maximize REE precipitation efficiency while minimizing the oxalic acid dosage. The operating parameters for this investigation were oxalic acid dosage, iron (III) contamination, solution pH and temperature. The resultant model suggested that oxalic acid dosage and reaction pH are the most significant factors for the REE precipitation efficiency, followed by the interaction of oxalic dosage and Fe concentration. Test results indicated that increasing the oxalic acid concentration from 0g/L to 80g/L improved the REE precipitation efficiency from approximately 4.2% to 95.0%. Furthermore, raising the solution pH from 0.5 to 2.5 considerably enhanced the precipitation efficiency from 0.0% to 98.9%. A solution temperature elevation decreased REE recovery, which indicated an exothermic reaction between REEs and oxalate anions. Finally, a high level of Fe contamination adversely impacted REE precipitation efficiency. The speciation analysis revealed that the dominant iron species in the solution system were Fe-(C₂O₄)₃³⁻, Fe-(C₂O₄)²⁻, and Fe-(C₂O₄)⁺, which consumed the majority of the oxalate anions

rare earth elements, acid baking, high-temperature↗

DOE OSTI2015

Results of initial analyses of the salt (macro) batch 9 tank 21H qualification samples

Savannah River National Laboratory (SRNL) analyzed samples from Tank 21H in support of qualification of Interim Salt Disposition Project (ISDP) Salt (Macro) Batch 9 for processing through the Actinide Removal Process (ARP) and the Modular Caustic-Side Solvent Extraction Unit (MCU). This document reports the initial results of the analyses of samples of Tank 21H. Analysis of the Tank 21H Salt (Macro) Batch 9 composite sample indicates that the material does not display any unusual characteristics or observations, such as floating solids, the presence of large amount of solids, or unusual colors. Further results on the chemistry and other tests will be issued in the future.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS1996

Isopycnic Phases and Structures in H2O/CO2/Ethoxylated Alcohol Surfactant Mixtures

Ternary mixtures of H2O and CO2 with ethoxylated alcohol (C(i)E(j)) surfactants can form three coexisting liquid phases at conditions where two of the phases have the same density (isopycnic phases). Isopycnic phase behavior has been observed for mixtures containing the surfactants C8E5, C10E6, and C12E6, but not for those mixtures containing either C4E1 or CgE3. Pressure-temperature (PT) projections for this isopycnic three-phase equilibrium were determined for H2O/CO2/C8E5 and H2O/CO2/C10E6 mixtures at temperatures from approximately 25 to 33 C and pressures between 90 and 350 bar. As a preliminary to measuring the microstructure in isopycnic three component mixtures, phase behavior and small angle neutron scattering (SANS) experiments were performed on mixtures of D2O/CO2/ n-hexaethyleneglycol monododecyl ether (C12E6) as a function of temperature (25-31 C), pressure (63.1-90.7 bar), and CO2 composition (0-3.9 wt%). Parameters extracted from model fits of the SANS spectra indicate that, while micellar structure remains essentially unchanged, critical concentration fluctuations increase as the phase boundary and plait point are approached.

Paulaitis, Michael E.↗

DOE OSTI2015

Electrical charging effects on the sliding friction of a model nano-confined ionic liquid

Recent measurements suggest the possibility to exploit ionic liquids (ILs) as smart lubricants for nano-contacts, tuning their tribological and rheological properties by charging the sliding interfaces. Following our earlier theoretical study of charging effects on nanoscale confinement and squeezout of a model IL, we present here molecular dynamics simulations of the frictional and lubrication properties of that model under charging conditions. First, we describe the case when two equally charged plates slide while being held together to a confinement distance of a few molecular layers. The shear sliding stress is found to rise strongly and discontinuously as the number of IL layers decreases stepwise. However, the shear stress shows, within each given number of layers, only a weak dependence upon the precise value of the normal load, a result in agreement with data extracted from recent experiments. We subsequently describe the case of opposite charging of the sliding plates and follow the shear stress when the charging is slowly and adiabatically reversed in the course of time, under fixed load. Despite the fixed load, the number and structure of the confined IL layers change with changing charge, and that in turn drives strong friction variations. The latter involves first of all charging-induced freezing of the IL film, followed by a discharging-induced melting, both made possible by the nanoscale confinement. Another mechanism for charging-induced frictional changes is a shift of the plane of maximum shear from mid-film to the plate-film interface, and vice versa. While these occurrences and results invariably depend upon the parameters of the model IL and upon its specific interaction with the plates, the present study helps identifying a variety of possible behavior, obtained under very simple assumptions, while connecting it to an underlying equilibrium thermodynamics picture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Data Center Facility Monitoring with Physics Aware Approach

U.S. Department of Energy's National Renewable Energy Laboratory (NREL) hosts one of the world's most energy-efficient HPC data centers; this system uses component-level warm-water liquid cooling to efficiently remove heat from the data center and capture it for reuse in the building or rejection to the atmosphere. Given the complexity of this system, building data-driven tools for holistically monitoring and operating the entire data center is a priority for ensuring maximal efficiency and resiliency. In this advanced smart facility, over one million metrics are recorded per minute using state-of-the-art streaming data architecture and software to capture and process the state of the system in real time. Here we detail two efforts to effectively analyze, visualize, and interpret this large volume streaming data. We have developed a novel, flexible system for identifying and visualizing individual metric anomalies and component performance across the data center through automatic metadata extraction and physically-motivated visualization for quick interpretation. Additionally, to directly connect system maintenance to data stream processing we explore a physics informed multi-metric drift and anomaly detection application to detect scale-build up in heat exchangers.

anomaly detection↗

DOE OSTI2022

High-throughput nuclear resonance time domain interferometry using annular slits

Nuclear resonance time domain interferometry (NR-TDI) is used to study the slow dynamics of liquids (that do not require Mössbauer isotopes) at atomic and molecular length scales. Here the TDI method of using a stationary two-line magnetized 57 Fe foil as a source and a stationary single-line stainless steel foil analyzer is employed. The new technique of adding an annular slit in front of a single silicon avalanche photodiode detector enables a wide range of momentum transfers (1 to 100 nm -1 by varying the distance between the annular slits and sample) with a high count rate of up to 160 Hz with a Δ q resolution of ±1.7 nm -1 at q = 14 nm -1 . The sensitivity of this method in determining relaxation times is quantified and discussed. The Kohlrausch–Williams–Watts (KWW) model was used to extract relaxation times for glycerol. These relaxation times give insight into the dynamics of the electron density fluctuations of glycerol as a function of temperature and momentum transfers.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

NASA NTRS2008

Sulfur 'Concrete' for Lunar Applications - Environmental Considerations

Commercial use of sulfur concrete on Earth is well established, particularly in corrosive, e.g., acid and salt, environments. Having found troilite (FeS) on the Moon raises the question of using extracted sulfur as a lunar construction material, an attractive alternative to conventional concrete as it does not require water. For the purpose of this Technical Memorandum, it is assumed that lunar ore is mined, refined, and the raw sulfur processed with appropriate lunar regolith to form, for example, bricks. With this stipulation, it is then noted that the viability of sulfur concrete in a lunar environment, which is characterized by lack of an atmosphere and extreme temperatures, is not well understood. The work presented here evaluates two sets of small sulfur concrete samples that have been prepared using JSC-1 lunar simulant as an aggregate addition. One set was subjected to extended periods in high vacuum to evaluate sublimation issues, and the other was cycled between room and liquid nitrogen temperatures to investigate their subsequent mechanical integrity. Results are presented from both investigations, discussed, and put into the context of the lunar environment.

Grugel, R. N.↗

NASA NTRS2011

Microwave Processing of Planetary Surfaces for Volatile Extraction

In-Situ Resource Utilization will be necessary for sustained exploration of space. Volatiles are present in planetary soils, but water by far has the strongest potential for effective utilization. The presence of water at the lunar poles, Mars, and possibly on Phobos opens the possibility of producing LOX for propellant. Water is also a useful radiation shielding material and water (and oxygen) are expendables that are also required for habitation in space. Because of the strong function of water vapor pressure with temperature, heating soil effectively liberates water vapor by sublimation. Microwave energy will penetrate soil and heat from within much more efficiently than heating from the surface with radiant heat. This is especially true under vacuum conditions since the heat transfer rate is very low. The depth of microwave penetration is a strong function of the microwave frequency and to a lesser extent on soil dielectric properties. Methods for measuring the complex electric permittivity and magnetic permeability are being developed and have been measured for some lunar soil simulants at 0.5, 2.45, and 10 GHz from room temperature down to liquid nitrogen temperature. A new method for delivery of microwaves deep into a planetary surface is being prototyped with laboratory experiments and modeled with COMSOL MultiPhysics. We have plans to set up a planetary testbed in a large vacuum chamber in the coming year. Recent results will be presented.

Ethridge, Edwin C.↗

DOE OSTI2023

Computational study of the ECN spray C via one-way coupling of internal nozzle flow and ensuing spray

Here, in this study, computational fluid dynamics simulations of the Engine Combustion Network Spray C injector were performed to investigate the effect of the internal nozzle flow on the development of the ensuing spray in automotive fuel injectors. A set of simulation best practices was first developed to achieve an accurate representation of the internal nozzle flow. Detailed, spatiotemporally defined information was extracted at the injector’s orifice exit and stored in maps that were subsequently employed to initialize a Lagrangian spray by means of a static, one-way coupling (OWC) approach. To highlight the impact of the in-nozzle flow on the spray, the OWC approach was compared with the conventional rate-of-injection (ROI) approach, for which the spray parcels are commonly initialized using a blob injection model. The results indicated that, using the ROI approach, considerable evaporation was observed within the plume in the near-nozzle region. On the other hand, the OWC approach showed evidence of evaporation farther downstream and at the plume periphery. The different behavior observed with the two approaches was mostly due to substantial differences in fuel mass distribution. The liquid fuel concentration predicted by the OWC approach matched well with X-ray tomography measurements of projected fuel mass per unit volume, in terms of both magnitude and distribution. In contrast, an unphysical distribution of fuel mass characterized by an extremely low liquid concentration was predicted by the ROI approach. In the far-field, the effect of the in-nozzle flow was found to be weaker as the spray penetrated and interacted with the ambient gas. In this region, the OWC and ROI approaches provided similar predictions of vapor penetration, spray morphology, and mixing-related characteristics.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2014

Early Results from the Q{sub weak} Experiment

A subset of results from the recently completed Jefferson Lab Q{sub weak} experiment are reported. This experiment, sensitive to physics beyond the Standard Model, exploits the small parity-violating asymmetry in elastic {vector e}p scattering to provide the first determination of the protons weak charge Q{sub w}{sup p}. The experiment employed a 180 {micro}A longitudinally polarized 1.16 GeV electron beam on a 35 cm long liquid hydrogen target. Scattered electrons corresponding to Q{sup 2} of 0.025 GeV{sup 2} were detected in eight Cerenkov detectors arrayed symmetrically around the beam axis. The goals of the experiment were to provide a measure of Q{sub w}{sup p} to 4.2 percent (combined statistical and systematic error), which implies a measure of sin2(thetaw) at the level of 0.3 percent, and to help constrain the vector weak quark charges C{sub 1u} and C{sub 1d}. The experimental method is described, with particular focus on the challenges associated with the worlds highest power LH{sub 2} target. The new constraints on C{sub 1u} and C{sub 1d} provided by the subset of the experiments data analyzed to date will also be shown, together with the extracted weak charge of the neutron.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NASA NTRS1998

Experiment 5: Science and Technology of Surface Controlled Oscillations: Report on USML-2 Results

Minuscule amounts (e.g., 1 part in 10,000) of a surface-active material in a liquid can drastically affect the surface behavior of the liquid, influencing how the material flows and mixes with other liquid and solid materials. In many respects, the science of surfactants has been empirical, with trial and error dominating over the ability to predict how surfactant type and concentration influence surface behavior. A program for the modeling of surfactant behavior has been established at Yale. This program combines experimental work performed both on the ground and in space, and theoretical and numerical modeling. By levitating a drop of liquid in air, away from solid container surfaces, and by manipulating the drop with acoustic radiation forces, we have been able to establish idealized conditions for surface behavior studies. The primary experiments involve the study of the free oscillations of initially deformed drops. In STS-73, the USML-2 mission of the Space Shuttle, we performed the following measurements: 1) the oscillation of a spherical drop in its quadrupole mode; 2) the oscillation of a drop about a deformed (oblate) shape; 3) the slow static squeezing of the drop from spherical to nearly flat; and 4) the superoscillations of drops when the radiation forces maintaining the drop in a flattened state are suddenly reduced. Analytic and numerical studies have enabled us to understand the physics of these oscillations and to extract material properties such as the dynamic surface tension and the surface viscosities (shear and dilatational). The relation to ground-based studies is essential, because the knowledge and understanding gleaned from our space studies enable us to interpret ground-based data.

Apfel, Robert E.↗