Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LASER OUTPUT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Laser adaptive holographic hydroacoustic intensimeter

A new type of a vector hydrophone, a laser adaptive hydroacoustic intensimeter, is investigated. Two identical, spatially separated coil-type sensors are used as a primary receiver of the acoustic signal. The signals received at the sensor output are phase demodulated in a two-channel adaptive holographic interferometer based on two dynamic holograms multiplexed in a CdTe photorefractive crystal. Using a laser intensimeter, the acoustic field formed in a limited volume is studied. The performance characteristics of the intensimeter are determined experimentally; its threshold sensitivity, according to the acoustic field intensity, constitutes 0.1 × 10{sup −13} W m{sup −2}. (laser applications)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Final Scientific and Technical Report - Practical Fiber Delivered Laser Ignition Systems for Vehicles

Research has characterized advanced kagome fiber optics for their use in laser ignition systems. In comparison to past fibers used in laser ignition, these fibers have the important advantage of being relatively bend-insensitivity, so that they can be bent and coiled without degradation of output energy or beam quality. The results are very promising for practical systems. For pulse durations of ~12 ns, the fibers could deliver >~10 mJ pulses before damage onset. A study of pulse duration showed that by using longer pulse duration (~20 – 30 ns), it is possible to carry even higher pulse energy (by factor of ~2-3) which also provides future opportunities to implement longer duration sources. Beam quality measurements showed nearly single-mode output from the kagome fibers (i.e. M2 close to 1) which is the optimum possible value and, combined with their high pulse energy, shows the suitability of the fibers for laser ignition. Research has also demonstrated laser ignition of an engine including reliable (100%) ignition of a single-cylinder gasoline engine using the laser ignition system with bent and coiled kagome fiber. The COV of IMEP was <2% which is favorable for stable engine operation. These research results, along with the continued reduction in cost of laser sources, support our commercial development of practical laser ignition systems.

ignition, laser ignition, vehicles, fiber optics↗

Diode lasers emitting at 1190 nm with a highly strained GaInAs quantum well and GaAsP compensating layers MOCVD-grown on a GaAs substrate

Laser heterostructures with an active region consisting of a highly strained GaInAs quantum well located between GaAsP compensating layers were grown by metal-organic chemical vapor deposition on GaAs substrates. Stripe mesa-structure laser diodes of 100 {mu}m aperture emitting at 1190 nm were fabricated. The highest emission power of these diodes in the CW mode amounted to 4.5 W per output mirror. Due to the presence of compensating GaAsP barriers, the GaInAs quantum well remains unrelaxed, which eliminates the spread in the maximum emission power of laser diodes produced from the same heterostructure.

36 MATERIALS SCIENCE↗

A highly efficient, 10-J output signal amplifier for ultra-intense all-OPCPA systems

Optical parametric chirped-pulse amplification (OPCPA) using high-energy Nd:glass lasers has the potential to produce ultra-intense pulses (>10 23 W/cm 2 ). We report on the performance of the final high-efficiency amplifier in an OPCPA system based on large-aperture (63 x 63-mm 2 ) partially deuterated potassium dihydrogen phosphate (DKDP) crystals. Here, the seed beam (170 nm, 240 mJ) was provided by the preceding OPCPA stages. The maximum pump-to-signal conversion efficiency of 37% was achieved with a 52-mm-long DKDP crystal and 40-J pump energy at 527 nm due to the flattop super-Gaussian pump beam profile and flat-in-time pulse shape. The 11.8-J output signal was compressed to 19 fs.

42 ENGINEERING↗

Temperature and current dependences of the lasing spectrum's width of quantum dot lasers

Dependences of the lasing spectrum's width of lasers based on arrays of self-organized InAs/InGaAs quantum dots on the temperature and output power have been experimentally studied. A theoretical analysis and simulation of the experimental results have been performed and the possibility of an adequate analytical description of the power and temperature dependences of the lasing line width in terms of the model developed has been demonstrated. It is shown that the main cause of the broadening of the lasing spectrum at low temperatures is the gain saturation in quantum dots as a result of the increase in the average carrier's escape and capture times.

36 MATERIALS SCIENCE↗

Distributed feedback terahertz frequency quantum cascade lasers with dual periodicity gratings

We have developed terahertz frequency quantum cascade lasers that exploit a double-periodicity distributed feedback grating to control the emission frequency and the output beam direction independently. The spatial refractive index modulation of the gratings necessary to provide optical feedback at a fixed frequency, and simultaneously, a far-field emission pattern centered at controlled angles, was designed through use of an appropriate wavevector scattering model. Single mode terahertz (THz) emission at angles tuned by design between 0° and 50° was realized, leading to an original phase-matching approach for highly collimated THz quantum cascade lasers.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Emission-Line Width and α-Factor of 850-nm Single-Mode Vertical-Cavity Surface-Emitting Lasers Based on InGaAs/AlGaAs Quantum Wells

The emission-line width for 850-nm single-mode vertical-cavity surface-emitting lasers based on InGaAs/AlGaAs quantum wells is studied. The width of the emission line for a laser with a 2-μm oxide current aperture attains it minimum (~110 MHz) at an output power of 0.8 mW. As the optical output power is further increased, anomalous broadening of the emission line is observed; this is apparently caused by an increase in the α-factor as a result of a decrease in the differential gain in the active region under conditions of increased concentration of charge carriers and of high internal optical losses in the microcavity. The α-factor is estimated using two independent methods.

36 MATERIALS SCIENCE↗

Optical communication with semiconductor laser diodes

Slot timing recovery in a direct detection optical PPM communication system can be achieved by processing the photodetector waveform with a nonlinear device whose output forms the input to a phase lock group. The choice of a simple transition detector as the nonlinearity is shown to give satisfactory synchronization performance. The rms phase error of the recovered slot clock and the effect of slot timing jitter on the bit error probability were directly measured. The experimental system consisted of an AlGaAs laser diode (lambda = 834 nm) and a silicon avalanche photodiode (APD) photodetector and used Q=4 PPM signaling operated at a source data rate of 25 megabits/second. The mathematical model developed to characterize system performance is shown to be in good agreement with actual performance measurements. The use of the recovered slot clock in the receiver resulted in no degradation in receiver sensitivity compared to a system with perfect slot timing. The system achieved a bit error probability of 10 to the minus 6 power at received signal energies corresponding to an average of less than 60 detected photons per information bit.

Davidson, F.↗

0.87-micron CSP diode lasers for spaceborne communications

Index-guided channeled-substrate-planar (CSP) AlGaAs diode lasers are being developed for reliable, high-power operation for use as sources in spaceborne optical communications systems. Although most work on this AlGaAs structure has been aimed at optimizing performance at output wavelengths less than 8400 A, emission in the 8700 A regime is also of interest. In particular, such wavelengths are required for use in the direct detection laser transceiver to be incorporated into NASA's advanced communications technology satellite, in order to avoid absorption of the light by the atmosphere when communicating with ground-based terminals. Lowest order spatial mode and substantially single longitudinal mode output has been observed in 0.87-micron CSP devices in excess of 50 mW cw and 100 mW 50 percent duty-cycle, with rms phase-front aberrations measured to be about lambda/40.

Carlin, D. B.↗

15 Gb/s index-coupled distributed-feedback lasers based on 1.3 μm InGaAs quantum dots

The static properties and large-signal modulation capabilities of directly modulated p-doped quantum-dot distributed-feedback lasers are presented. Based on pure index gratings the devices exhibit a side-mode-suppression ratio of 58 dB and optical output powers up to 34 mW. Assisted by a broad gain spectrum, which is typical for quantum-dot material, emission wavelengths from 1290 nm to 1310 nm are covered by the transversal and longitudinal single-mode lasers fabricated from the same single wafer. Thus, these lasers are ideal devices for on-chip wavelength division multiplexing within the original-band according to the IEEE802.3ba standard. 10 Gb/s data transmission across 30 km of single mode fiber is demonstrated. The maximum error-free data rate is found to be 15 Gb/s.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Lidar Measurements of Metallic Species in Mesopause Region

Sodium density distributions were measured over more than 20 nights since Jul. 1991 at Tokyo Metropolitan University. Our sodium lidar specifications are shown. The lidar consists of a dye laser that is pumped by a pulsed Nd:YAG laser. The dye laser is tuned to the D2 resonant absorption line of Na at the wavelength of 589 nm. A small fraction of the output beam is directed to a hollow-cathode lamp. The precise tuning of the Na D2 line is accomplished by monitoring the signal obtained from the hollow-cathode lamp and controlling the grating in the dye laser oscillator cavity. The raw data for each profile were obtained by firing the laser 5000 times for approximately 8.5 minutes. We have observed the sporadic sodium layers three times during the observation period. Recently, lidar measurements of iron atoms were also performed. Other aspects of this investigation are presented.

Nagasawa, Chikao↗

Fourth-order harmonic generation during parametric four-wave mixing in the filaments in ambient air

We propose a simplified scheme for efficient 200-nm pulse generation in isotropic medium using 800-nm radiation. The observation and optimization of the fourth-order harmonic generation during two-color filamentation in air are reported. This parametric process is based on four-wave mixing of the fundamental and the second-order harmonic radiation of the Ti:sapphire laser. A systematic study of the influence of the laser intensity, the polarization, the chirp, and the pulse duration on the fourth-order harmonic output from the filaments has been carried out. The fourth-order harmonic conversion efficiency was estimated to be of the order of 10{sup -4}.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Perovskite Solar Module: Promise and Challenges in Efficiency, Meta‐Stability, and Operational Lifetime

Abstract Perovskite photovoltaics (PVs) are an emerging solar energy generation technology that is nearing commercialization. Despite the unprecedented progress in increasing power conversion efficiency (PCE) for perovskite solar cells (PSCs), up‐scaling lab‐made cells to solar modules remains a challenge. In this work, the recent progress of making perovskite mini‐modules is reviewed. In particular, a database summarizing the module size, performance, hysteresis, and operational lifetimes reported in the literature is built. After analyzing the performance losses from scaling PSCs to mini‐modules based on the data collected from the literature, the current key to high‐performance perovskite mini‐modules is found to be the coating method optimization. If the perovskite layer quality is well reserved, a >24% mini‐module efficiency is projected by only considering the losses from lateral resistivity and laser scribing area. Next, performance characteristics are explored including hysteresis and meta‐stable power outputs that must be overcome to correctly characterize perovskite modules. Finally, current challenges associated with the long‐term stability of perovskite modules are examined and the importance of such durability for commercialization is discussed. It is hoped that the findings in this review provide a bridge for the development of perovskite modules that will lead to commercialization in the near future.

36 MATERIALS SCIENCE↗

Lens window simplifies TDL housing

Lens window seal in tunable-diode-laser housing replaces plan parallel window. Lens seals housing and acts as optical-output coupler, thus eliminating need for additional reimaging or collimating optics.

Robinson, D. M.↗

Theoretical studies of solar lasers and converters

The research described consisted of developing and refining the continuous flow laser model program including the creation of a working model. The mathematical development of a two pass amplifier for an iodine laser is summarized. A computer program for the amplifier's simulation is included with output from the simulation model.

Heinbockel, John H.↗

Experimental study of the dynamics of a ruby laser pumped by a CW argon-ion laser

A study of the dynamics of a ruby laser pumped by a CW argon-ion laser is presented. The ruby laser is predominantly stable but has two accessible unstable states. One state exhibits chaotic output, while the other results in regular self-pulsing. The conditions needed for instability are discussed and homodyne spectra and temporal maps of the phase-space attractors are obtained. In addition, a numerical simulation of nonlinear beam propagation in ruby is presented that shows that strong deviations from plane-wave behavior exist, and that transverse effects must be incorporated into theoretical models of the instability.

Afzal, R. S.↗

Low-Loss Coupler For Microwave Laser-Diode Modulation

Elimination of series resistor reduces loss of radio-frequency power. Quarter-wavelength matching section connected to transmission line eliminates need for resistor near laser diode and extends frequency response of system. Concept significantly extends relatively flat frequency response of laser diode or similar component, while simplifying design of its package, increasing amplitude of output signal, and reducing dissipation of heat by eliminating resistance. Phase characteristics approximately linear and any digital information transmitted not significantly altered.

Toda, Minoru↗