Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Homogenization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Influence of Multidirectional Forging on Microstructural, Mechanical, and Corrosion Behavior of Mg-Zn Alloy

Multidirectional forging (MDF) was applied to Mg-6%Zn alloy up to 5 passes successfully at 280 °C. MDF-processed materials were characterized using optical microscope, scanning electron microscope, electron backscatter diffraction, transmission electron microscope, and x-ray diffraction. Obtained results showed a significant reduction in grain size (up to 3.8 μm) having a large fraction of high-angle grain boundaries after 5 passes of MDF process. Maximum tensile strength of 230 MPa was achieved for 5-pass MDF-processed Mg-6%Zn alloy which is about ~ 2.0 times higher in comparison with that of homogenized alloy (117 MPa) and was attributed to higher dislocations density and grain refinement. Corrosion behavior of the alloy was investigated in 0.1 M NaCl solution using potentiodynamic polarization test, electrochemical impedance spectra analysis, and immersion tests. It was found that the corrosion rate of 5-pass MDF sample improved (0.34 mm/year) ~2.5 times in comparison with that of homogenized Mg-6%Zn alloy (0.86 mm/year) due to fine grain structure, which creates more grain boundaries that act as a corrosion barrier.

36 MATERIALS SCIENCE↗

Effect of Preheated Microstructure Vis-à-vis Process Parameters and Characterization of Orange Peel in Incremental Forming of AA1050 Sheets

The present investigation systematically analyzes and compares the influence of microstructure and crystallographic texture of AA1050 sheet to that of the most critical process parameters, namely tool dimension, and incremental step depth, in single-point incremental forming (SPIF) process. The sheet samples were preheated at different temperatures to reform the original, i.e., distorted and misoriented grain distribution. The results from experimental and statistical analyses report higher sensitivity of global spring back, surface topography and forming limits strains to variations in microstructure and texture than tool diameter and incremental step depth. The preheating of the sheets resulted in the formation of preferential texture by grain reformation, which leads to the increase in the fraction of homogeneous orientated grains. Such grains increase the maximum forming limit strains and reduce the global spring back in SPIF. Fractography analysis of the failed components revealed that improvement in formability due to grain homogenization (developed texture) may be attributed to larger average void diameter. Empirical models were also developed, and optimized levels of parameters were identified to maximize the efficiency of the SPIF process. Further, qualitative and quantitative characterization of orange peel roughness was carried out by segregating the external formed surface into surfaces subjected to orange peel roughness and tool-induced texture.

36 MATERIALS SCIENCE↗

Strength Variation in Processing Multiport Extrusion Tubes of A1100 and A3102 Alloys

The manufacturing process of multiport extrusion tubes generally includes homogenization, extrusion, roll leveling and heat treatment. In order to investigate the influence of the manufacturing procedures on strength variation of multiport extrusion tubes made of A1100 and A3102 alloys, the tube fabrication experiments and following materials characterization are carried out. The alloys’ stress–strain curves after every processing procedure are measured, and pressure-bearing capacity of the tubes is tested. The tubes’ strength and pressure-bearing capacity reach the peak values after straightening process and drop to the minimum after annealing. The contributions of solid solution hardening, grain boundary hardening and constituent particle strengthening to yield strength are evaluated. It is deduced that cluster hardening is the dominant strengthening mechanism for the as-homogenized and as-extruded samples; the contribution of clusters is second to work hardening after straightening process; slight cold work in conjunction with high-temperature annealing accelerates abnormal grain growth. The loss of strength increment from clusters can be interpreted by the remarkable reduction of high-angle grain boundaries after abnormal grain growth.

36 MATERIALS SCIENCE↗

Long-Term Creep Behavior of a CoCrFeNi Medium-Entropy Alloy

We report that current research shows that high-entropy alloys (HEAs) can offer superior oxidation resistance compared to more traditional austenitic stainless steels with equivalent tensile mechanical performance. While many reports have been published on creep of CoCrFeNiMn, few focus on the CoCrFeNi family of low to medium entropy alloys. In this manuscript, uniaxial tensile creep test results for more than 46,000 accumulated hours are presented on the equiatomic CoCrFeNi alloy. The alloy was manufactured at NETL using a vacuum induction melt solidification approach with a computationally designed homogenization cycle. After completing the homogenization cycle, the ingot was first hot forged and then hot rolled into 10 mm thick plate, a product form that is relevant to many industries. Creep tests were performed in the temperature range of 600-650 °C using applied stresses from 120 to 189 MPa. This study builds upon previous results on the CoCrFeNiMn family of high-entropy alloys and offers a modicum of clarification about performance compared to small button melts by using ASTM standard test procedures and mechanical test specimens. The apparent creep activation energy and creep stress exponent were similar to those for CoCrFe medium-entropy and CoCrFeNiMn high-entropy alloys. The post-test creep microstructure showed some Cr segregation, which has also been noted for other CoCrFe alloys. The CoCrFeNi alloy also presents a double minimum or two minimum creep rate phenomena.

36 MATERIALS SCIENCE↗

Fabrication of oxide dispersion strengthened bond coats with low Al 2 O 3 content [Fabrication of ODS bond coats with low Al 2 O 3 content]

Here, nanoscale oxide dispersions have long been used to increase the oxidation and wear resistance of alloys used as bond coatings in thermal barrier coatings. Their manufacturing via mechanical alloying is often accompanied by difficulties regarding their particle size, homogeneous distribution of the oxide dispersions inside the powder, involving considerable costs, due to cold welding of the powder during milling. A significant improvement in this process can be achieved by the use of process control agent (PCA) to achieve the critical balance between cold welding and fracturing, thereby enhancing the process efficiency. In this investigation, the influence of the organic additive stearic acid on the manufacturing process of Al 2 O 3 -doped CoNiCrAlY powder was investigated. Powders were fabricated via mechanical alloying at different milling times and PCA concentrations. The results showed a decrease in particle size, without hindering the homogeneous incorporation of the oxide dispersions. Two powders manufactured with 0.5 and 1.0 wt.% PCA were deposited by high velocity oxygen fuel (HVOF) spraying. Results showed that a higher content of elongated particles in the powder with the higher PCA content led to increased surface roughness, porosity and decreased coating thickness, with areas without embedded oxide particles.

36 MATERIALS SCIENCE↗

Microstructural Characterization of U-Nb-Zr, U-Mo-Nb, and U-Mo-Ti Alloys via Electron Microscopy

Ternary uranium molybdenum alloys are currently being investigated for use as dispersion and monolithic nuclear fuels in research reactors. In this study, two such ternary alloys, with compositions U-8Mo-3Nb and U-7Mo-3Ti in wt.%, were examined using scanning electron microscopy (SEM), X-ray diffraction (XRD), and transmission electron microscopy (TEM) with high angle annular dark field (HAADF) imaging via scanning transmission electron microscopy (STEM) to identify phase constituents. These alloys were homogenized at 950°C for 96 hours and were expected to be single-phase bcc-!-U. However, upon examination, it was determined that despite homogenization, each of the alloys contained a small volume fraction precipitate phase. Through SEM and XRD, it was confirmed that the matrix retained the bcc-!-U phase, but the precipitate phases could not be identified using these methods. TEM specimens were prepared using site-specific focused ion beam (FIB) in situ lift out (INLO) technique to include at least one precipitate from each alloy. By electron diffraction, the precipitate phases for the U- 8Mo-3Nb and U-7Mo-3Ti alloys were identified as bcc-(Mo,Nb) solid solution and bcc- (Mo,Ti) solid solution, respectively.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural evolution of single Ni 2 TiAl or hierarchical NiAl/Ni 2 TiAl precipitates in Fe-Ni-Al-Cr-Ti ferritic alloys during thermal treatment for elevated-temperature applications

Precipitate features, such as the size, morphology, and distribution, are important parameters determining the mechanical properties of semi- or fully-coherent precipitatehardened alloys at elevated temperatures. In this study, the microstructural formation and evolution of recently-developed Fe-Ni-Al-Cr-Ti alloys with superior creep resistance have been systematically investigated using transmission-electron microscopy (TEM), scanning-electron microscopy (SEM), and atom-probe tomography (APT). These alloys were designed by adding 2 or 4 weight percent (wt. %) Ti into a NiAl-hardened ferritic alloy with a nominal composition of Fe-6.5Al-10Cr-10Ni-3.4Mo-0.25Zr-0.005B in wt. %. These alloys were, then, subjected to a homogenization treatment at 1,473 K for 0.5 hour, followed by aging treatments at 973 K for 1 ~ 500 hours. In the homogenization-treated case, both alloys contain a primary L21-type Ni 2 TiAl precipitate, but with the distinct size and morphology of the precipitates and precipitate/matrix interface structures. In the subsequent aging treatments, the 2 wt. % Ti alloy establishes a hierarchical-precipitate structure consisting of a fine network of a B2-type NiAl phase within the parent L2 1 -type Ni2TiAl precipitate, while the 4 wt. % Ti alloy retains the single Ni 2 TiAl precipitate. It was found that the hierarchical structure is more effective in remaining the coherent interface during the growth/coarsening of the precipitate. The formation of the different types of the precipitates, and their effects on the microstructural evolution are discussed, and the driving forces for these features are identified from the competition between the interface energy and elastic interactions due to the lattice misfit and misfit dislocations.

36 MATERIALS SCIENCE↗

Microstructure selection in thin-sample directional solidification of an Al-Cu alloy: In situ X-ray imaging and phase-field simulations

We study microstructure selection during directional solidification of a thin metallic sample. We combine in situ X-ray radiography of a dilute Al-Cu alloy solidification experiments with three-dimensional phase-field simulations. We explore a range of temperature gradient G and growth velocity V and build a microstructure selection map for this alloy. We investigate the selection of the primary dendritic spacing Lambda and tip radius rho. While rho shows a good agreement between experimental measurements and dendrite growth theory, with rho similar to V-1/2, Lambda is observed to increase with V (partial derivative Lambda/partial derivative V > 0), in apparent disagreement with classical scaling laws for primary dendritic spacing, which predict that partial derivative Lambda/partial derivative V <0. We show through simulations that this trend inversion for Lambda(V) is due to liquid convection in our experiments, despite the thin sample configuration. We use a classical diffusion boundary-layer approximation to semi-quantitatively incorporate the effect of liquid convection into phase-field simulations. This approximation is implemented by assuming complete solute mixing outside a purely diffusive zone of constant thickness that surrounds the solid-liquid interface. This simple method enables us to quantitatively match experimental measurements of the planar morphological instability threshold and primary spacings over an order of magnitude in V. We explain the observed inversion of partial derivative Lambda/partial derivative V by a combination of slow transient dynamics of microstructural homogenization and the influence of the sample thickness.

36 MATERIALS SCIENCE↗

Effect of tube processing methods on microstructure, mechanical properties and irradiation response of 14YWT nanostructured ferritic alloys

In this research, innovative thermal spray deposition (Process I) and conventional hot extrusion processing (Process II) methods have been used to produce thin walled tubing (~0.5 mm wall thickness) out of 14YWT, a nanostructured ferritic alloy. The effects of processing methods on the microstructure, mechanical properties and irradiation response have been investigated by using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and, micro- and nano-hardness techniques. It has been found that these two processes have a significant effect on the microstructure and mechanical properties of the as-fabricated 14YWT tubes. Even though both processing methods yield the formation of various size Y-Ti-O particles, the conventional hot extrusion method results in a microstructure with smaller, homogenously distributed nano-oxides (NOs, Y-Ti-O particles < 5 nm) with higher density. Therefore, Process II tubes exhibit twice the hardness of Process I tubes. It has also been found that these two tremendously different initial microstructures strongly affect irradiation response in these tubes under extremely high dose ion irradiations up to 1100 peak dpa at 450 °C. The finer, denser and homogenously distributed NOs in the Process II tube result in a reduction in swelling by two orders of magnitude. On the other hand, inhomogeneity of the initial microstructure in the Process I tube leads to large variations in both swelling and irradiation induced hardening. Moreover, hardening mechanisms before and after irradiation were measured and compared with detailed calculations. In conclusion, this study clearly indicates the crucial effect of initial microstructure on radiation response of 14YWT alloys.

36 MATERIALS SCIENCE↗

Grain boundary engineering to control the discontinuous precipitation in multicomponent U10Mo alloy

Grain boundaries in metallic alloys often play a crucial role, not only in determining the mechanical properties or thermal stability of alloys, but also in dictating the phase transformation kinetics during thermomechanical processing. We demonstrate that locally stabilized structure and compositional segregation at grain boundaries—“grain boundary complexions”—in a complex multicomponent alloy can be modified to influence the kinetics of cellular transformation during subsequent thermomechanical processing. Using aberration-corrected scanning transmission electron microscopy and atom probe tomography analysis of a metallic nuclear fuel highly relevant to worldwide nuclear non-proliferation efforts —uranium-10 wt% molybdenum (U-10Mo) alloy, new evidence for the existence of grain boundary complexion is provided. We then modified the concentration of impurities dissolved in Υ-UMo grain interiors and/or segregated to Υ-UMo grain boundaries by changing the homogenization treatment, and these effects were used used to retard the kinetics of cellular transformation during subsequent sub-eutectoid annealing in this U-10-Mo alloy during sub-eutectoid annealing. Thus, this work provided insights on tailoring the final microstructure of the U-10Mo alloy, which can potentially improve the irradiation performance of this important class of alloy fuels.

Devaraj, Arun (ORCID:0000000313146212)↗

Structural dynamics and rejuvenation during cryogenic cycling in a Zr-based metallic glass

Subjecting metallic glasses repeatedly to liquid nitrogen temperature has become a popular method to homogeneously rejuvenate the material. Here in this paper we reveal the atomic-scale structural dynamics using in-situ x-ray photon correlation spectroscopy (XPCS) during and after cryogenic cycling of a Zr-based metallic glass in two structural states (plate and ribbon). Heterogeneous structural dynamics is observed at 300 K that changes to monotonic aging at 78 K. It is found that cryogenic cycling homogenizes the relaxation time distribution. This effect is much more pronounced in the ribbon, which is the only structural state that rejuvenates upon cycling. We furthermore reveal how fast atomic-scale dynamics is correlated with long-time structural relaxation times irrespective of the structural state, and that the ribbon exhibits unexpected additional fast atomic-scale relaxation in comparison to the plate material. A structural picture emerges that points towards heterogeneities in the fictive temperature as a requirement for cryogenic energy storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Material properties and mechanical behaviour of functionally graded steel produced by wire-arc additive manufacturing

Metal Big Area Additive Manufacturing is an additive manufacturing technique based on Gas Metal Arc Welding (GMAW) with the option to use many shielding gases, and materials. The system is equipped with a dual torch design allowing for printing different materials; in our study, AISI 410 stainless steel and AWS ER70S-6 mild steel are both printed in the same component. Different print strategies were designed to highlight changes in material and mechanical properties. Deformation behaviour of a materials’ interface was analysed by two-dimensional digital image correlation of uniaxial tensile specimens in displacement-controlled tests. Instances of non-homogeneous local strains adjacent to the interface are observed, as well as variability in mechanical behaviour and microstructure based on location within the print. Optical and electron microscopy are used to evaluate three microstructural zones in a 5 mm range of the interface between mild steel and stainless steel. Areas far from the interface produced polygonal ferrite and pearlite, while areas close to the interface produced acicular ferrite and bainite. Chromium redistribution profiles are dependent on the print strategy used, as shown by scanning electron microscopy with Energy dispersive spectroscopy. Evidence produced via electron backscatter diffraction is shown to support the argument that transformation induced plasticity is not the cause for the non-homogeneous deformation.

36 MATERIALS SCIENCE↗

Coupled supercritical CO2 dissolution and water flow in pore-scale micromodels

Dissolution trapping is one of the most important mechanisms for geological carbon storage (GCS). Recent laboratory and field experiments have shown non-equilibrium dissolution of supercritical CO2 (scCO2) and coupled scCO2 dissolution and water flow, i.e., scCO2 dissolution at local pores/pore throats creating new water-flow paths, which in turn enhance dissolution by increased advection and interfacial area. However, the impacts of pore-scale characteristics on these coupled processes have not been investigated. In this study, imbibition and dissolution experiments were conducted under 40°C and 9?MPa using a homogeneous/isotropic hexagonal micromodel, two homogeneous elliptical micromodels with low or high anisotropy, and a heterogeneous sandstone-analog micromodel. The four micromodels, initially saturated with deionized (DI)-water, were drained by injecting scCO2 to establish a stable scCO2 saturation. DI water was then injected at different rates with logCa (the capillary number) ranging from -6.56 to -4.34. Results show that bypass of scCO2 by displacing water is the dominant mechanism contributing to the residual CO2 trapping, triggered by heterogeneity in pore characteristics or pore-scale scCO2-water distribution. Bypass can be enhanced by pore heterogeneity or reduced by increasing transverse permeability, resulting in relatively low (<2% of CO2 solubility) or high (9–13% of CO2 solubility) dissolved CO2 concentration in displacing water. The overall dissolution of residual scCO2 increases with decreasing Ca, and approaches to their solubility at low Ca value with sufficient residence time. This main trend is similar to a capillary desaturation curve that represents the relationship between the residual saturation and Ca. Spatially, dissolution initiates along the boundary of bypassed scCO2 cluster(s) in a non-equilibrium manner, and the coupling of water flow and dissolution occurs which fragments the bypassed scCO2 clusters and enhance scCO2 dissolution.

Chang, Chun↗

Radiation dose rate distributions of spent fuel dry casks estimated with MAVRIC based on detailed geometry and continuous-energy models

This study presents a detailed comparison of the dose rate distributions of a dry TN–32 fuel cask with two geometry models and two cross-sectional datasets. The accuracies of radiation dose rate estimation and computational efficiencies of each geometry model with two cross-sectional data-sets are compared. The use of automated variance reduction techniques can significantly improve the computational efficiency of such a realistic, deep penetration problem that involves radiation transport from different volumetric sources, thereby eliciting only a small statistical error. Monaco with Automated Variance Reduction using Importance Calculations (MAVRIC) is a computational sequence within the SCALE 6.2 code package based on consistent adjoint driven importance sampling (CADIS), a type of automated variance reduction technique. Homogenous and full fuel assembly models are built herein, and two nuclear cross-section libraries (V7–200N47G and continuous energy) are applied in this work. Based on the detailed comparisons, we found that neutron dose rate estimation is more dependent on geometry modeling than on cross-section data. For neutron-induced gamma rays, the dose rate distribution depends on both the spatial self-shielding effect and the cross-section library. The primary gamma rays respectively contribute to the total dose rate by ~91% and ~ 99% on side and top surfaces, and the dose rate accuracy is more dependent on the cross-section library than on geometry modeling. In terms of the computation efficiency and efforts spent on geometry modeling, the homogenous fuel assembly model with the MG library can produce an acceptable dose rate distribution, but the detailed fuel assembly model with the continuous-energy library is required for more precise dose rate estimation.

61 RADIATION PROTECTION AND DOSIMETRY↗

Subplane collision probabilities method applied to control rod cusping in 2D/1D

The MPACT code is being jointly developed by the University of Michigan and Oak Ridge National Laboratory. It uses the 2D/1D method to solve neutron transport problems for reactors. The 2D/1D method decomposes the problem into a stack of 2D planes, and uses a high fidelity transport method to resolve all heterogeneity in each plane. These planes are then coupled axially using a lower order solver. Using this scheme, 3D solutions to the transport equation can be obtained at a much lower cost.One assumption made by the 2D/1D method is that the materials are axially homogeneous for each 2D plane. Violation of this assumption requires homogenization, which can significantly reduce the accuracy of the calculation. This paper presents two new subgrid methods to address this issue. The first method is polynomial decusping, a simple correction used to address control rods partially inserted into a 2D plane. The second is the subplane collision probabilities method, which is a more accurate, more robust subgrid method that can be applied to other axial heterogeneities.Each method was applied to a variety of problems. Results were compared to fine mesh solutions which had no axial heterogeneity and to Monte Carlo reference solutions generated using KENO-VI. It was shown that the polynomial decusping method was effective in many cases, but it had some limitations, with 3D pin power errors as high as 25% compared to KENO-VI. In conclusion, the subplane collision probabilities method performed much better, lowering the maximum pin power error to less than 5% in every calculation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Calculation of multi-group migration areas in deterministic transport simulations

Recent work on the Cumulative Migration Method (CMM) has demonstrated that it is possible to define multi-group transport cross sections directly from Monte Carlo spectral calculations by utilizing edits of the energy-dependent neutron migration areas. However, it is difficult to demonstrate that downstream deterministic transport calculations actually preserve Monte Carlo migration areas. This paper addresses this issue by: 1) demonstrating the relationship of migration area with the concept of mean squared displacement, 2) deriving, and validating vs. Monte Carlo, an analytic expression for computing one-group migration areas for a homogeneous medium with energy-independent cross sections, 3) deriving, and validating vs. Monte Carlo, an analytic expression for computing multi-group migration areas for a homogenized medium with energy-dependent cross sections, and 4) rigorously proving that energy condensation of multi-group transport cross section must be inverse flux weighted in order to preserve Monte Carlo neutron migration areas.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Particulate Fuel Modeling of MC 2 -3 using Iterative Local Spatial Self-shielding Method

We report a new spatial self-shielding method for particulate fuels has been developed based on disadvantage factors and implemented in the MC 2 -3 code. This method named the iterative local spatial self-shielding (ILSS) method considers the shadowing effect of randomly distributed particles on spatial self-shielding in particles through a homogenized composition region added outside the particle of interest at the center. The self-shielded cross sections of the central particle are determined iteratively since they are used in determining the cross sections of the homogenized composition region. The ILSS method was verified for infinite stochastic medium problems of single and multiple types of particles, VHTR unit cell problems, and HTTR assembly problems. The verification test results show that the ILSS method accurately predicts the stochastic particle shadowing effect and reaction rates in particles, whereas the regular array model and the stochastic collision probability method underpredict the particle shadowing effect and overestimate reaction rates in particles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗