Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Growth efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Structure and evolution of a severe squall line over Oklahoma

The structure of a severe squall line that developed in Oklahoma on May 2, 1979, is presented during its growth and part of its mature period. The line was analyzed using radar, satellite, sounding, and surface data for examining, in particular, the cell propagation mechanisms, the three-dimensional structure of the squall line and individual cells during the mature period, the mass and moisture fluxes, and precipitation efficiency. Comparison of the 1979 Oklahoma squall line with other documented squall lines indicates less well organized down-drafts on the rear side at low levels to midlevels, and an absence of low level to midlevel inflow on the rear side. The magnitude of mass and moisture fluxes was comparable to previous squall line cases. At one point, the motion of the individual cells, initially associated with a synoptic scale cold front, takes a sharp rightward turn. The mechanism of the motion turn is explained in terms of conditions created by a combination of wind shear and moisture convergence and lifting.

Heymsfield, G. M.↗
NASA NTRS1986

Flat-plate solar array project. Volume 3: Silicon sheet: Wafers and ribbons

The primary objective of the Silicon Sheet Task of the Flat-Plate Solar Array (FSA) Project was the development of one or more low cost technologies for producing silicon sheet suitable for processing into cost-competitive solar cells. Silicon sheet refers to high purity crystalline silicon of size and thickness for fabrication into solar cells. Areas covered in the project were ingot growth and casting, wafering, ribbon growth, and other sheet technologies. The task made and fostered significant improvements in silicon sheet including processing of both ingot and ribbon technologies. An additional important outcome was the vastly improved understanding of the characteristics associated with high quality sheet, and the control of the parameters required for higher efficiency solar cells. Although significant sheet cost reductions were made, the technology advancements required to meet the task cost goals were not achieved.

Briglio, A.↗
NASA NTRS1998

Approaches in the Determination of Plant Nutrient Uptake and Distribution in Space Flight Conditions

The effective growth and development of vascular plants rely on the adequate availability of water and nutrients. Inefficiency in either the initial absorption, transportation, or distribution of these elements are factors which may impinge on plant structure and metabolic integrity. The potential effect of space flight and microgravity conditions on the efficiency of these processes is unclear. Limitations in the available quantity of space-grown plant material and the sensitivity of routine analytical techniques have made an evaluation of these processes impractical. However, the recent introduction of new plant cultivating methodologies supporting the application of radionuclide elements and subsequent autoradiography techniques provides a highly sensitive investigative approach amenable to space flight studies. Experiments involving the use of gel based 'nutrient packs' and the nuclides Ca45 and Fe59 were conducted on the Shuttle mission STS-94. Uptake rates of the radionuclides between ground and flight plant material appeared comparable.

Heyenga, A. G.↗
NASA NTRS2006

Phototransistor (PT) in the 2 Micron Region

Within the framework of the project the University of Delaware has developed InGaAsSb-based heterojunction phototransistors (HPT) structure with a large (1000 micron diameter) photosensitive/photoactive area. Two different compositions of quaternary alloys were used to provide the cutoff wavelength (50% of maximum quantum efficiency) of 2.4 micron (Type 1) and 2.15 micron (Type 2). The Type 1 HPT was composed of Al0.25Ga0.75As0.02Sb0.98 and In0.18Ga0.82As0.17Sb0.83 layers with room-temperature bandgaps of Eg approximates 1.0 eV and Eg approximates 0.54 eV, respectively. The layers are lattice-matched to a GaSb substrate. The growth started with a 0.15micron-thick n+-GaSb buffer layer and was completed with a 0.1 m-thick n+- GaSb contact layer doped with Te. The HPT structure includes a 0.5 m-thick n-type AlGaAsSb emitter, 0.8 micron-thick p-type composite base consisting of AlGaAsSb (0.3 m) and InGaAsSb (0.5 m) layers, and a 1.5micron - thick n type InGaAsSb collector. The Type 2 HPT differed by a higher bandgap In0.16Ga0.84As 0.14Sb0.86 layers with a room-temperature bandgap of Eg approximates 0.555 eV.

Prather, Dennis↗
NASA NTRS2015

Expanding Fungal Diets Through Synthetic Algal-Fungal Mutualism

Fungi can synthesize numerous molecules with important properties, and could be valuable production platforms for space exploration and colonization. However, as heterotrophs, fungi require reduced carbon. This limits their efficiency in locations such as Mars, where reduced carbon is scarce. We propose a system to induce mutualistic symbiosis between the green algae Chlamydomonas reinhardtii and the filamentous fungi Neurospora crassa. This arrangement would mimic natural algal-fungal relationships found in lichens, but have added advantages including increased growth rate and genetic tractability. N. crassa would metabolize citrate (C6H5O7 (sup -3)) and release carbon dioxide (CO2) that C. reinhardtii would assimilate into organic sugars during photosynthesis. C. reinhardtii would metabolize nitrate (NO3−) and release ammonia (NH3) as a nitrogen source for N. crassa. A N. crassa mutant incapable of reducing nitrate will be used to force this interaction. This system eliminates the need to directly supply its participants with carbon dioxide and ammonia. Furthermore, the release of oxygen by C. reinhardtii via photosynthesis would enable N. crassa to respire. We hope to eventually create a system closer to lichen, in which the algae transfers not only nitrogen but reduced carbon, as organic sugars, to the fungus for growth and production of valuable compounds.

Fungi↗
NASA NTRS2024

Integration of Automated Systems Test Campaign NC-IAS

NASA’s 2022 strategic plan included the goal to catalyze economic growth and drive innovation in the aviation industry, and to address challenges in air transportation and airspace management within the National Airspace System (NAS). The Aeronautics Research Mission Directorate (ARMD) specifically was tasked with leading aviation innovation to enable safe and sustainable air transportation through revolutionary vehicle advances and efficient flight operations. As a part of meeting these objectives and advancing air mobility concepts, NASA initiated the National Campaign (NC) in the Advanced Air Mobility (AAM) Project within the Airspace Operations and Safety Program (AOSP). The NC was designed to support operational demonstrations with industry as well as the research and development needed to support NASA-led research flight demonstrations. Within NC, the Integration of Automated Systems (IAS), an NC activity, tested and evaluated flight deck automation and airspace operations management functions needed to enable Urban Air Mobility (UAM) operations. This was accomplished through a partnership with Sikorsky Aircraft (specifically Sikorsky Innovations), a Lockheed Martin company, and DARPA (Defense Advanced Research Projects Agency), by leveraging two automation-enabled helicopters equipped with unique capabilities that enabled NASA to develop and test two-ship conflict encounters to demonstrate flight path management and hazard avoidance technologies. The enabler in this testing was NASA-developed “Middleware” (MW) software (also known as Expandable Variable Autonomy Architecture, or EVAA), which among other things allowed multiple algorithms to be incorporated into one software build that was hosted on the dissimilar-type Sikorsky helicopters. The IAS test campaign period of performance was from March 2022 through October 2023 and was structured as a phased, or spiral, approach that ultimately led to the first-ever demonstration of two-ship UAM/AAM operations designed to safely choreograph specific conflict encounters and mission scenarios to test the research algorithms for strategic and tactical aircraft deconfliction. Lessons learned are included in the body of the report. Data collected will be used to inform FAA and industry standards groups on the increasingly automated systems needed for future AAM operations. The test encounters developed for these flight tests were proven to be highly predictable, repeatable, and safely exercised flight path planning and Detect and Avoid (DAA) algorithms. These same test encounters should be leveraged by future flight test campaigns to verify that operational safety is not compromised as the AAM architecture matures. Next steps include repeating similar encounters using unmanned aircraft carrying DAA sensors in the National Airspace.

AAM↗
DOE OSTI2020

FY20 NREL Overview: Transforming Energy

At the National Renewable Energy Laboratory (NREL), we are transforming today’s energy challenges into tomorrow’s solutions. Our scientific research and technological innovation will shape a highly efficient and resilient energy future. Our world is transforming around us with energy solutions becoming cleaner, cheaper, renewable, and more resilient. As the population grows and new technologies and devices are added to the grid, we must examine the effects and enhance security within our most critical systems. As environmental threats expand and human demands on urban centers increase, we need more sustainable and efficient ways of generating energy that considers resource competition worldwide. We need our grid to be adaptive, autonomous, and responsive. NREL continues to anticipate these challenges, offering solutions through research, innovation, analysis, partners, and people. We are building the foundation of tomorrow’s energy landscape and inspiring the economic growth of the future.

energy security↗
DOE OSTI2024

Getting to the root of the problem: Soil carbon and microbial responses to root inputs within a buried paleosol along an eroding hillslope in southwestern Nebraska, USA

Large quantities of soil carbon (C) can persist within paleosols for millennia due to burial and subsequent isolation from plant-derived inputs, atmospheric conditions, and microbial activity at the modern surface. Erosion exposes buried soils to modern root-derived C influx via root exudation and root turnover, thus stimulating microbial activity leading to SOC decomposition and accumulation through organo-mineral stabilization of modern C. With this study we aim to quantify how modern root-derived C inputs impact paleosol C decomposition and stabilization across varying degrees of isolation from modern surface conditions in southwestern Nebraska, USA, where hillslope erosion is bringing a buried Late-Pleistocene-early Holocene paleosol (the “Brady Soil”) closer to the modern surface. We collected Brady Soil samples from 0.2m, 0.4m, and 1.2m below the modern surface and conducted two lab-based incubations. Soils were amended with either (1) a lab-synthesized mixture of low molecular weight compounds (12 atom% 13 C), or (2) 13 C enriched root residues (92 atom% 13 C), in 30-day and 240-day incubation experiments, respectively. Here we determined microbial responses to synthetic root exudates and residues by partitioning the 13 C label from Brady Soil C, including measurements of total, root, and primed C respiration, microbial biomass C (MBC), microbial C use efficiency (CUE). To assess the capacity of isolated paleosols to accrue modern plant C, we used Nano-scale Secondary Ion Mass Spectrometry imaging. We found that: (1) adding root-derived C inputs primed Brady Soil C across all depths, and was mediated by depth and composition of root additions; (2) root-derived C inputs stimulated microbial biomass C (MBC) growth similarly across depths, but the magnitude of CUE and MBC varied by chemistry of root-derived additions; (3) new particulate organic matter was incorporated into mineral-associated pools over time; (4) material from the added root residues was found in association with bacterial cells and fungal hyphae as well as with soil aggregate and mineral surfaces. Our study shows that paleosols defy expectations of C content and reactivity with depth, and changes in land cover and climate will expose buried paleosols to modern surface conditions, increasing respired C. This work highlights the importance of evaluating the role resurfacing buried soils through landscape change plays in C cycle feedbacks to the climate system.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Characterization of n-Type Iodine-Doped and Indium-Doped CdTe/Cd-Se-Te Thin Films Fabricated by Close-Spaced Sublimation Epitaxy

In this study, n-type CdTe thin films, specifically iodine-doped CdTe (CdTe:I), indium-doped CdTe (CdTe:In), and indium-doped Cd-Se-Te (CST:In), were synthesized using close-spaced sublimation epitaxy (CSSE). Characterization techniques secondary ion mass spectrometry (SIMS), electron backscatter diffraction (EBSD), Hall-effect measurements, and time-resolved photoluminescence (TRPL) were employed to analyze the chemical, structural, and electronic properties of these materials. The results indicated epitaxial single crystal CSSE films grew on the single crystal substrates, with carrier density ranging from 10^14 - 10^16 cm -3 , and after post-annealing, the minority-carrier lifetimes reach near the radiative limit. Additionally, a preliminary exploration of homojunction structures with an n- type (CdTe:In /CST:In /CdTe:I) /CdTe:P /Cu /Mo configuration was performed. The best device performance was achieved with CdTe:I including CdS aiding in band alignment, resulting in a power conversion efficiency (..eta..) of 2.61% with open circuit voltage (Voc) of 850 mV, fill factor (FF) of 47.8%, and short-circuit current (Jsc) of 6.44 mA/cm 2 . The observed low Jsc and efficiency may be attributed to a buried junction and a poor interface, due to dopant interdiffusion. Consequently, further investigations focusing on interface optimization, diffusion blocking, and reduced recombination through passivation, are crucial to enhancing the efficiency of CSSE CdTe homojunction devices in the future.

cadmium compounds↗
DOE OSTI2022

Rapid and efficient hydrogen clathrate hydrate formation in confined nanospace

Clathrate hydrates are crystalline solids characterized by their ability to accommodate large quantities of guest molecules. Although CH 4 and CO 2 are the traditional guests found in natural systems, incorporating smaller molecules (e.g., H 2 ) is challenging due to the need to apply higher pressures to stabilize the hydrogen-bonded network. Another critical limitation of hydrates is the slow nucleation and growth kinetics. Here, we show that specially designed activated carbon materials can surpass these obstacles by acting as nanoreactors promoting the nucleation and growth of H 2 hydrates. The confinement effects in the inner cavities promote the massive growth of hydrogen hydrates at moderate temperatures, using pure water, with extremely fast kinetics and much lower pressures than the bulk system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Application of reference-free natural background–oriented schlieren photography for visualizing leakage sites in building walls

Air leakage in buildings can cause health and comfort concerns for occupants and can contribute to mold growth on building materials, or in extreme conditions, rot of building materials. Unwanted air leakage through the building envelope also contributes to approximately 4 quadrillion Btu (1172 TWh) of energy consumption per year in the building sector in the United States. Locating and sealing leakage sites can improve the energy efficiency, comfort, air quality, and moisture durability of the building stock. Typical methods of finding leakage sites, such as infrared imaging and smoke tracing, rely on concurrent blower door operation, which can also measure the total leakage rate of the building. Smoke tracing can be disruptive to occupants, and infrared imaging and smoke tracing cannot measure the contribution of individual leaks to prioritize sealing efforts. Here, an optical fluid flow imaging technique, reference-free natural background–oriented schlieren imaging, was adapted to visualize air exfiltration. This is the first step in developing a method to noninvasively locate and measure exfiltration or infiltration sites so that sealing efforts can be prioritized. Experimental results of this technique are presented, demonstrating the method's applicability to visualizing exfiltration through three common building claddings in an outdoor environment. Key variables impacting the performance of this technique when applied to building leakage are also discussed.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Thermally generated magnonic spin currents in a polycrystalline gadolinium iron garnet thin film with perpendicular magnetic anisotropy

Rare-earth iron garnets (REIGs) are the benchmark systems for magnonics, including the longitudinal spin Seebeck effect (LSSE). While most research has focused on single-crystalline REIGs on complimentary garnet substrates, moving to more, cost-effective complementary metal-oxide semiconductor (CMOS)-compatible substrates is important to integrate REIG thin films with existing technology. In this regard, we grow a 130 nm-thick polycrystalline gadolinium iron garnet (GdIG) film on the Si/SiO2 substrate and investigate the temperature-dependent LSSE. Interestingly, the polycrystalline GdIG film exhibits perpendicular magnetic anisotropy (PMA) at room temperature which is induced by tensile in-plane (IP)-strain originating from the thermal-expansion mismatch between the GdIG film and the substrate during rapid thermal annealing. Further, a spin-reorientation transition from the out-of-plane IP direction below TS = 180 K is observed. Additionally, the film reveals a magnetic compensation temperature, TComp, of ≈240 K. The LSSE voltage not only demonstrates a sign-inversion around TComp, but also shows noticeable changes around TS. As compared to a single-crystalline GdIG film, the lower LSSE voltage for the polycrystalline GdIG is attributed to the higher effective magnetic anisotropy and enhanced magnon scattering at the grain boundaries. Our study not only paves the way for the cost-effective growth of CMOS-compatible REIG-based systems with PMA for magnonic memory and information processing applications, but also highlights the fact that the spincaloritronic and spin-insulatronic properties of the polycrystalline REIGs follow those of their single-crystalline counterparts with reduced spin-to-charge conversion efficiency through LSSE which can be tuned further by controlling the average gran size and interface engineering.

Physics↗
DOE OSTI2021

Crystallization in one-step solution deposition of perovskite films: Upward or downward?

Despite the fast progress of perovskite photovoltaic performances, understanding the crystallization and growth of perovskite films is still lagging. One unanswered fundamental question is whether the perovskite films are grown from top (air side) to bottom (substrate side) or from bottom to top despite 10 years of development. Here, by using grazing incidence x-ray diffraction and morphology characterizations, we unveil that the perovskite films prepared by one-step solution processes, including antisolvent-assisted spin coating and blade coating, follow the downward growth from intermediate phase during thermal annealing. Such a top-to-bottom downward growth is initialized by the evaporation of residual solvent from the top surface of “wet” films and is less sensitive to perovskite compositions and the wettability of underlying substrates. Addressing this fundamental question is important to understand the heterogeneity of perovskite films along the vertical direction, which markedly affects the efficiency and stability of perovskite solar cells.

36 MATERIALS SCIENCE↗
NASA NTRS1978

Laser-zone growth in a Ribbon-To-Ribbon (RTR) process. Silicon sheet growth development for the large area sheet task of the low-cost solar array project

A new calculation of the effects of thermal stresses during growth on silicon ribbon quality is reported. Thermal stress distributions are computed for ribbon growth under a variety of temperature profiles. A growth rate of 55 cu cm/min with a single ribbon was achieved. The growth of RTR ribbon with a fairly uniform parallel dendritic structure was demonstrated. Results with two approaches were obtained for reducing the Mo impurity level in polycrystalline feedstock. Coating the Mo substrate with Si3N4 does not effect thermal shear separation of the polyribbon; this process shows promise of improving cell efficiency and also increasing the useful life of the molybdenum substrate. A number of solar cells were fabricated on RTR silicon grown from CVD feedstock.

Baghdadi, A.↗
NASA NTRS1990

MSAT: A booster for land based mobile radiocommunication networks?

It is demonstrated that the foreseen phenomenal growth of mobilesat services will impact positively existing terrestrial mobile radio services. Mobilesat systems will not displace the existing terrestrial market in the near future, partly due to the high cost of their terminal units and associated airtime, but also due to some technical limitations, such as lack of spectrum efficiency and high susceptibility to shadowing. However, the ubiquity of mobilesat services will open new market to terrestrial radio technologies. The latter is expected to be the most economical way of extending locally mobilesat services to many users. Conversely, mobilesat systems will be used to extend the capabilities of terrestrial radio systems in areas where the former cannot be implemented cost effectively. It is believed that terrestrial mobile network operators using these service extension capabilities will have a competitive advantage over those who do not. Overall, it is expected that emerging mobilesat services, far from being a threat to terrestrial radio systems, will rather provide these with numerous opportunities of incrementing their base market.

Boulay, Guy↗
NASA NTRS2000

InGaP/InGaAs-on-Ge Concentrator Solar Cell for Space Power Generation

The passivating front and back window layer of the top cell has been chosen. We have chosen to use InGaAs as the tunnel junction interconnect compound since it is easily degenerately doped. All of the dual junction cell structures were grown on GaAs substrates. Time constraints prevented us from completing the development of the GaAs-on-Ge growth process. Analysis of the I-V and EQE data, and comparison with computer-modeled data, shows that the performance of the dual-junction cell is still being controlled by the bottom cell, in spite of top cell thinning. Further improvement in the dual-junction cell efficiency is possible by thinning the front window.

Sinharoy, Samar↗
NASA NTRS2010

Spinoff 2010

Topics covered include: Burnishing Techniques Strengthen Hip Implants; Signal Processing Methods Monitor Cranial Pressure; Ultraviolet-Blocking Lenses Protect, Enhance Vision; Hyperspectral Systems Increase Imaging Capabilities; Programs Model the Future of Air Traffic Management; Tail Rotor Airfoils Stabilize Helicopters, Reduce Noise; Personal Aircraft Point to the Future of Transportation; Ducted Fan Designs Lead to Potential New Vehicles; Winglets Save Billions of Dollars in Fuel Costs; Sensor Systems Collect Critical Aerodynamics Data; Coatings Extend Life of Engines and Infrastructure; Radiometers Optimize Local Weather Prediction; Energy-Efficient Systems Eliminate Icing Danger for UAVs; Rocket-Powered Parachutes Rescue Entire Planes; Technologies Advance UAVs for Science, Military; Inflatable Antennas Support Emergency Communication; Smart Sensors Assess Structural Health; Hand-Held Devices Detect Explosives and Chemical Agents; Terahertz Tools Advance Imaging for Security, Industry; LED Systems Target Plant Growth; Aerogels Insulate Against Extreme Temperatures; Image Sensors Enhance Camera Technologies; Lightweight Material Patches Allow for Quick Repairs; Nanomaterials Transform Hairstyling Tools; Do-It-Yourself Additives Recharge Auto Air Conditioning; Systems Analyze Water Quality in Real Time; Compact Radiometers Expand Climate Knowledge; Energy Servers Deliver Clean, Affordable Power; Solutions Remediate Contaminated Groundwater; Bacteria Provide Cleanup of Oil Spills, Wastewater; Reflective Coatings Protect People and Animals; Innovative Techniques Simplify Vibration Analysis; Modeling Tools Predict Flow in Fluid Dynamics; Verification Tools Secure Online Shopping, Banking; Toolsets Maintain Health of Complex Systems; Framework Resources Multiply Computing Power; Tools Automate Spacecraft Testing, Operation; GPS Software Packages Deliver Positioning Solutions; Solid-State Recorders Enhance Scientific Data Collection; Computer Models Simulate Fine Particle Dispersion; Composite Sandwich Technologies Lighten Components; Cameras Reveal Elements in the Short Wave Infrared; Deformable Mirrors Correct Optical Distortions; Stitching Techniques Advance Optics Manufacturing; Compact, Robust Chips Integrate Optical Functions; Fuel Cell Stations Automate Processes, Catalyst Testing; Onboard Systems Record Unique Videos of Space Missions; Space Research Results Purify Semiconductor Materials; and Toolkits Control Motion of Complex Robotics.

Source record↗
NASA NTRS2000

Crystal Growth of ZnSe and Related Ternary Compound Semiconductors by Vapor Transport

Interest in optical devices which can operate in the visible spectrum has motivated research interest in the II-VI wide band gap semiconductor materials. The recent challenge for semiconductor opto-electronics is the development of a laser which can operate at short visible wavelengths. In the past several years, major advances in thin film technology such as molecular beam epitaxy and metal organic chemical vapor deposition have demonstrated the applicability of II-VI materials to important devices such as light-emitting diodes, lasers, and ultraviolet detectors. With an energy gap of 2.7 eV at room temperature, and an efficient band- to-band transition, ZnSe has been studied extensively as the primary candidate for a blue light emitting diode for optical displays, high density recording, and military communications. By employing a ternary or quaternary system, the energy band gap of II-VI materials can be tuned to a specific range. While issues related to the compositional inhomogeneity and defect incorporation are still to be fully resolved, ZnSe bulk crystals and ZnSe-based heterostructures such as ZnSe/ZnSeS, ZnSe/ZnCdSe and ZnCdSe/ZnSeS have showed photopumped lasing capability in the blue-green region at a low threshold power and high temperatures. The demonstration of its optical bistable properties in bulk and thin film forms also make ZnSe a possible candidate material for the building blocks of a digital optical computer. Despite this, developments in the crystal growth of bulk H-VI semiconductor materials has not advanced far enough to provide the low price, high quality substrates needed for the thin film growth technology.

Su, Ching-Hua↗