Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Design Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Benchmark Wall Heat Flux Data for a GO2/GH2 Single Element Injector

Computational Fluid Dynamics (CFD) is becoming an important component of injector design in the rocket industry. Injector designers who use CFD in the design process need to understand the accuracy level of the particular code being used for certain aspects of the design. This paper presents a recent effort to acquire benchmark quality data to be used for CFD code validation. Detailed chamber wall temperature and heat flux data was acquired for a gaseous oxygen, gaseous hydrogen single element shear coaxial injector in a 1.5 inch diameter copper heat sink chamber at Penn State University. The data was taken using both coaxial and water cooled heat flux gauges. Tests were run using hot gases generated from both fuel and oxidizer preburners. Tests were conducted over a chamber pressure range of 300 to 750 psia. Data analysis and uncertainty information will also be presented.

Pal, Sibtosh↗
NASA NTRSDate not supplied

Large-Drop Ice Accretion Test Results for a Large Scale Swept Wing Model

In-flight icing is an important consideration that affects aircraft design, performance and safety. Newer regulations combined with increasing demand to reduce fuel burn, emissions and noise are driving a need for improvements in icing simulation capability. To that end, this paper presents the results of ice accretion testing conducted in the NASA Icing Research Tunnel on a large swept wing section typical of a modern commercial transport. The model was based upon a section of the Common Research Model wing at the 64% semispan station with a streamwise chord length of 136 in. The test conditions were developed with an icing scaling analysis to generate similar conditions for a small MVD = 25 μm and a large MVD = 110 μm. A series of tests were conducted over a range of total temperature from -23.8 ˚C to -1.4 ˚C with all other conditions held constant. The results for the small MVD cloud conditions were consistent with previous work and showed the changing ice morphology from rime ice at colder temperatures to highly 3D scallop ice in the range of -8.7 ˚C to -3.8 ˚C. The results for the large MVD cloud conditions exhibited some differences in the ice accretion morphology from the small MVD conditions. Scallop-like ice features were observed at total temperature of -3.8˚C. The large MVD ice accretion at lower temperatures tended to be smoother than the corresponding ice accretion for small MVD. The thickness of the main ice shape tended to be larger for the small MVD conditions compared to the corresponding large MVD ice shape while the latter had more ice farther downstream. The measured ice mass was approximately equal between the corresponding small and large MVD ice shapes up to a freezing fraction of 0.6. For higher freezing fraction, the large MVD ice shapes weighed more. Cloud MVD variation from 50 μm to 230 μm while holding the scaling parameters constant resulted in very minor differences in the ice shapes, mostly in the upper and lower surface chordwise extents. Ice volume was computed from 3D scan data and used to calculate a ratio of ice mass to volume. The resulting values were in the range of 240 to 455 Kg/m3. While this is consistent with analogous values previously reported in the literature, more data are needed to determine a specific trend in this ratio as a function of freezing fraction and the corresponding governing physical phenomena. This work has resulted in a significant experimental database of ice accretion for small and large MVD conditions applicable to large-scale swept wings.

Icing↗
DOE OSTI2022

Insert Modeling in UNF ST&DARDS

The Used Nuclear Fuel-Storage, Transportation & Disposal Analysis Resource and Data System (UNF-ST&DARDS) is a software tool that integrates a used nuclear fuel (UNF) or spent nuclear fuel (SNF) relational database and key analysis capabilities to simplify and automate numerous UNF management and fuel cycle–related activities. UNF-ST&DARDS is being developed for the US Department of Energy’s Office of Nuclear Energy Spent Fuel and Waste Disposition program. UNF-ST&DARDS provides an integrated framework that uses advanced modeling and simulation to predict the behavior of SNF over the timescales associated with permanent disposal in a geologic repository. After leaving the spent fuel pool, SNF is transferred to dry storage in a dual-purpose canister (DPC). DPCs are considered “dual purpose” because they are designed for both storage and transportation, removing the need to transfer the fuel to a separate transportation cask. However, much research has been conducted investigating the feasibility of directly disposing of DPCs in geologic repositories. Direct disposal of DPCs could reduce worker exposure during repackaging, reducing the amount of low-level waste from the discarded DPCs and potentially saving billions of dollars. Therefore, direct disposal of as-loaded DPCs is desirable if it can be done safely.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Microreactor Core Transportation Cask Model Description for Criticality Safety Validation Basis Assessment (Rev. 1)

Criticality safety analyses are completed on transportation casks used for microreactor whole core shipment to provide examples of models and analyses to industry, regulators, and nuclear community at large to be used in verification and validation analyses of similar applications. The microreactors considered are based on a Gas-Cooled Microreactor (GCMR) and a Heat-Pipe Microreactor (HPMR), both utilize HALEU fuel in the form of TRISO particles and various other design options considered in industry microreactor designs. Variant design options of GCMR and HPMR were also investigated to provide a wider application range for each technology. Criticality safety analyses for the GCMR and HPMR packages were performed using the CSAS6 sequence of SCALE 6.3.2 with the ENDF/B-VII.1-based continuous energy neutron libraries. Different scenarios were investigated, including normal operation and water flooded conditions to represent nominal and hypothetical accident scenarios. Sensitivity and similarity analyses are also performed using the TSUNAMI sequence of SCALE 6.3.2, and the similarity analysis uses all the experiments from the ICSBEP Handbook with Intermediate and mixed Enriched Uranium (IEU) and Low Enriched Uranium (LEU) systems, together with additional experiments that are sponsored by the DNCSH program. Many experiments were found marginally similar to the GCMR and HPMR models, with similarity index (ck) values greater than 0.8 but less than 0.9. Among all the experiments analyzed, no case has a ck value greater than 0.9, indicating that additional critical experiments might be needed to further validate the criticality safety models for microreactors transport packages.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1978

Engine component improvement: JT8D and JT9D performance improvements

A feasibility analysis screening method for predicting the airline acceptance of a proposed engine performance improvement modification was developed. Technical information derived from available test data and analytical models is used along with conceptual/preliminary designs to establish the predicted performance improvement, weight and installation characteristics, the cost for new production and retrofit, maintenance cost and qualitative characteristics of the performance improvement concepts being evaluated. These results are used to arrive at the payback period, which is the time required for an airline to recover the investment cost of concept implementation, and to predict the amount of fuel saved by a performance improvement concept. The assumptions used to calculate the payback period and fuel saved are discussed. A summary of the results when the screening method is applied is presented for several representative JT8D and JT9D performance improvement concepts. An example of the input information used to develop the summary results is shown.

Gaffin, W. O.↗
NASA NTRS1993

Rover/NERVA-derived near-term nuclear propulsion

FY-92 accomplishments centered on conceptual design and analyses for 25, 50, and 75 K engines with emphasis on the 50 K engine. During the first period of performance, flow and energy balances were prepared for each of these configurations and thrust-to-weight values were estimated. A review of fuel technology and key data from the Rover/NERVA program established a baseline for proven reactor performance and areas of enhancement to meet near-term goals. Studies were performed of the criticality and temperature profiles for probable fuel and moderator loadings for the three engine sizes, with a more detailed analysis of the 50 K size. During the second period of performance, analyses of the 50 K engine continued. A chamber/nozzle contour was selected and heat transfer and fatigue analyses were performed for likely construction materials. Reactor analyses were performed to determine component radiation heating rates, reactor radiation fields, water immersion poisoning requirements, temperature limits for restartability, and a tie-tube thermal analysis. Finally, a brief assessment of key enabling technologies was made, with a view toward identifying development issues and identification of the critical path toward achieving engine qualification within 10 years.

Source record↗
DOE OSTI2025

Depletion Analysis of a Generic Fast Spectrum Molten Salt Reactor Supporting Material Control and Accounting (Rev.1)

Advanced reactors are of interest for a variety of use scenarios, and there are numerous advanced reactor designs being considered, which includes molten salt reactors (MSRs). Depending on the design, advanced reactors may have more extensive material control and accounting (MC&A) processes than current Light Water Reactor (LWR) designs. This project evaluated the use of Monte Carlo simulations for generating information that could guide the development of MC&A approaches for MSRs. In particular, the current capabilities of MCNP version 6.3 internally coupled with CINDER’90 were assessed for a fast spectrum liquid fueled MSR with online fission product removal and refueling. The fission product removal and refueling was performed in batches, and a Python wrapper was developed to control the simulations and update the fuel composition.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Exploring filamentous fungi depolymerization of corn stover in the context bioenergy queuing operations

Recalcitrance of lignocellulosic feedstocks to depolymerization is a significant barrier for bioenergy production approaches that require conversion of monomeric carbohydrates to renewable energy sources. This study assesses how low-cost modifications in the feedstock supply chain can be transformed into targeted pretreatments in the context of the entire bioenergy supply chain. The aim of this research is to overcome the physiochemical barriers in corn stover that necessitate increased severity in conversion in terms of chemical loading, temperature, and residence time. Corn stover samples were inoculated with a selective (Ceriporiopsis subvermispora) and non-selective (Phaenarochaete chrysosporium) lignin degrading filamentous fungal strains, then stored aerobically to determine the working envelope for fungal pretreatment to achieve lignin degradation. Dry matter loss and gross chemical makeup of corn stover varied by the length of treatment (2 and 4 weeks) and by the moisture content of the treated corn stover samples (40 and 60%, wet basis). Dry matter loss in P. chrysosporium inoculated biomass was elevated compared to the C. subvermispora inoculated biomass; however, treatment also induced additional chemical composition changes suggestive of depolymerization. Scanning electron microscope images reveal hyphae attached within cell lumen and suggest structural changes within P. chrysosporium treated corn stover after 60% moisture storage. These results highlight that fungal treatment approaches must balance loss of convertible material with the potential for reduction in recalcitrance. Techno-economic assessment (TEA) of fungal pretreatment in a short-term queuing system indicated the viability of this approach compared to conventional queuing operations. The total queuing system cost was estimated at $\$$1.65/tonne of biomass stored. After applying the credit of $\$$1.48/tonne from energy savings in the conversion phase using fungal pretreated biomass, the total system cost was $0.80 lower than traditional biomass queueing approach. While the TEA results suggested that treating biomass with C. subvermispora is the most economically viable storage method in the designed fungal-assisted queuing system, future research should focus on additional fungal depolymerization such as those observed in the P. chrysosporium inoculated biomass.

09 BIOMASS FUELS↗
DOE OSTI2024

Metallurgical Analysis of the High Flux Isotope Reactor (HFIR) Carrier Lifting Bails (Rev.1)

The dissolution rates of the aluminum alloys in the High Flux Isotope Reactor (HFIR) element carriers and the Material Test Reactor (MTR) L-bundles in the H-Canyon facility have been identified as the possible cause of extended dissolutions that result in significant time and financial expenditures. A study, carried out by Savannah River National Laboratory (SRNL) to determine relationships between the dissolution rates and the metallurgical properties of the aluminum alloy materials of construction of the HFIR carriers and the L-bundles, considered the dissolution rates of aluminum alloy (AA) series 1100, 6061, and 6063. The study determined that the aluminum alloy compositions played a principal role in the dissolution rate of the carrier/bundle components. Higher dissolution rates were correlated with lower concentrations of the minor element additions in the alloys and with specific element concentrations. Aluminum alloys 1100 and 6063 were found to have similar dissolution rates that were approximately two orders of magnitude (100X) greater than those of AA6061. Based on the results of the dissolution behavior study, a Technical Assistance Request (TAR) was first issued to determine if the replacement of AA6061-T6 with AA6063-T6 is feasible for the HFIR carrier lifting bails. A Technical Task Request was then issued to consider AA6063-T5 as well as other alloys to improve possible supply chain issues. The metallurgical properties of the L-bundle (specifically the end caps) were not evaluated in this report because L-Bundle drawings already allow for the use of AA6063-T6 in all structural components. The HFIR carriers are composed of thin-walled components with significant surface areas that allow for relatively quick overall dissolution times. Conversely, the carrier lifting bails and the supporting constituents are composed of solid bars and thick plate regions with relatively small surface areas that experience longer overall dissolution times. While the MTR L-bundle design includes allowances for the materials of construction to be either AA6061-T6 or AA6063-T6, the HFIR carriers are specified to be constructed fully with AA6061-T6 alloy. This report analyzes the recommendations of the dissolution behavior study to replace the materials of construction of the HFIR carrier lifting bails. The analysis considers the operational requirements of the lifting bail and its supporting structures. To decrease dissolution times, the analysis considers direct replacement of the material as well as reductions in the thicknesses of the components to decrease the mass of the elements. Material reductions are considered on options for using either AA6061 and/or AA6063. The calculations are based on specifications from the American Society of Mechanical Engineer (ASME) and The Aluminum Association, Inc. design codes. The analysis finds that direct replacement of the lifting bail material of construction with AA6063-T6, and AA6063-T5 as well as reductions in the dimensions of the lifting bail components are acceptable. Note that this study considers the structural suitability of the alloys. It does not consider their dissolution rates in the dissolvers.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1985

Numerical analysis of flow non-uniformity in the hot gas manifold of the Space Shuttle main engine

Three-dimensional viscous flow in a conceptual hot gas manifold (HGM) for the Space Shuttle Main Engine High Pressure Fuel Turbopump (SSME HPFTP) was numerically analyzed. A finite difference scheme was used to solve the Navier-Stokes equations. The exact geometry of the SSME HGM was modeled using boundary fitted curvilinear coordinates and the General Interpolants Method (GIM) code. Slight compressibility of the subsonic flow was modeled using a linearized equation of state with artificial compressibility. A time relaxation method was used to obtain a steady state solution. The feasibility and potential usefulness of computational methods in assisting the design of SSME components which involves the flow of fluids within complex geometrical shapes is demonstrated.

Thoenes, J.↗
NASA NTRS1959

Application of Gas Analysis to Combustor Research

The performance of turbine-engine combustors usually is given in terms of operating limits and combustion efficiency. The latter property is determined most often by measuring the increase in enthalpy across the combustor through the use of thermocouples. This investigation was conducted to determine the ability of gas-analytical techniques to provide additional information about combustor performance. Gas samples were taken at the outlet and two upstream stations and their compositions determined. In addition to over-all combustion efficiency, estimates of local fuel-air ratios, local combustion efficiencies, and heat-release rates can be made. Conclusions can be drawn concerning the causes of combustion inefficiency and may permit corrective design changes to be made more intelligently. The purpose of this investigation was not to present data for a given combustor but rather to show the types and value of additional information that can be gained from gas-analytical data.

Hibbard, R. R.↗
DOE OSTI2020

Multi-resolution, Multi-scale Modeling for Scalable Macroalgae Production

Macroalgae harvested along coastlines and in the open ocean has traditionally been used as food for human consumption, animal feed, and fertilizer. The U.S. ARPA-E MARINER Program estimates that the nation has suitable conditions and geography to produce at least 500 million dry metric tons of macroalgae per year, yielding approximately 2.7 quadrillion BTUs of energy in the form of liquid fuel, which is roughly 10% of the nation’s annual transportation energy demand. Adverse environmental effects of nutrient overload and ocean acidification may also be reduced by large-scale macroalgae cultivation in many coastal ocean regions. However, the successful deployment of large-scale marine macroalgae farms for fuel production depends on ambient hydrodynamic conditions and nutrient availability, as well as their interactions with macroalgae farm structures. Pacific Northwest National Laboratory led an ARPA-E MARINER project to develop a set of numerical modeling tools capable of simulating ocean hydrodynamic and biogeochemical processes, macroalgae trajectories for free-floating systems, macroalgae growth and biomass yields, and hydrodynamic load on macroalgae canopies and farm structures using a multi-resolution and multi-scale approach. This set of modeling tools provides a suite of information essential for system design, optimal project siting, risk analysis, and management of macroalgae production systems in the ocean. Better clarity can also help macroalgae system developers reduce deployment costs, operational risk, and potential impacts on the local marine environment.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1975

Gas sampling method for determining pollutant concentrations in the flame zone of two swirl-can combustor modules

A gas sampling probe and traversing mechanism were developed to obtain detailed measurements of gaseous pollutant concentrations in the primary and mixing regions of combustors in order to better understand how pollutants are formed. The gas sampling probe was actuated by a three-degree-of-freedom traversing mechanism and the samples obtained were analyzed by an on-line gas analysis system. The pollutants in the flame zone of two different swirl-can combustor modules were measured at an inlet-air temperature of 590 K, pressure of 6 atmospheres, and reference velocities of 23 and 30 meters per second at a fuel-air ratio of 0.02. Typical results show large spatial gradients in the gaseous pollutant concentration close to the swirl-can module. Average concentrations of unburned hydrocarbons and carbon monoxide decrease rapidly in the downstream wake regions of each module. By careful and detailed probing, the effect of various module design features on pollutant formation can be assessed. The techniques presently developed seem adequate to obtain the desired information.

Duerr, R. A.↗
NASA NTRS1981

Automotive Stirling reference engine design report

The reference Stirling engine system is described which provides the best possible fuel economy while meeting or exceeding all other program objectives. The system was designed to meet the requirements of a 1984 Pontiac Phoenix (X-body). This design utilizes all new technology that can reasonably be expected to be developed by 1984 and that is judged to provide significant improvement, relative to development risk and cost. Topics covered include: (1) external heat system; (2) hot engine system; (3) cold engine system; (4) engine drive system; (5) power control system and auxiliaries; (6) engine instalation; (7) optimization and vehicle simulation; (8) engine materials; and (9) production cost analysis.

Source record↗
NASA NTRS1999

Trade Study of Five In-Situ Propellant Production System for a Mars Sample Return Mission

One of the goals of NASA''s HEDS enterprise is to establish a long-term human presence on Mars at a fraction of the cost of employing today''s technology. The most direct method of reducing mission cost is to reduce the launch mass of the spacecraft. If the propellants for the return phase of the mission are produced on Mars, the total spacecraft mass could be reduced significantly. An interim goal is a Mars Sample Return (MSR) mission, which is proposed to demonstrate the feasibility of in-situ propellant production (ISPP). Five candidate ISPP systems for producing two fuels and oxygen from the Martian atmosphere are considered in this design trade-off study:(1) Zirconia cell with methanol synthesis, (2) Reverse water gas shift (RWGS) with water electrolysis and methanol synthesis, (3) Sabatier process for methane production with water electrolysis, (4) Sabatier process with water electrolysis and partial methane pyrolysis, and (5) Sabatier/RWGS combination with water electrolysis. These systems have been the subject of numerous previous analytical studies and laboratory demonstrations. In this investigation, the systems are objectively compared on the basis of thermochemical performance models using a commonly used chemical plant analysis software package. The realistic effects of incomplete chemical conversion and gas phase separator performance are included in these models. This study focuses on the chemical processing and product separation subsystems. The CO2 compression upstream of the chemical plane and the liquefaction/storage components are not included here.

Green, S. T.↗
NASA NTRS1999

Overview of Current Turbine Aerodynamic Analysis and Testing at MSFC

An overview of the current turbine aerodynamic analysis and testing activities at NASA/Marshall Space Flight Center (MSFC) is presented. The presentation is divided into three areas. The first area is the three-dimensional (3D), unsteady Computational Fluid Dynamics (CFD) analysis of the Fastrac turbine. Results from a coupled nozzle, blade, and exit guide vane analysis and from an uncoupled nozzle and coupled blade and exit guide vane will be presented. Unsteady pressure distributions, frequencies, and exit profiles from each analysis will be compared and contrasted. The second area is the testing and analysis of the Space Shuttle Main Engine (SSME) High Pressure Fuel Turbopump (HPFTP) turbine with instrumented first stage blades. The SSME HPFTP turbine was tested in air at the MSFC Turbine Test Equipment (TTE). Pressure transducers were mounted on the first stage blades. Unsteady, 3D CFD analysis was performed for this geometry and flow conditions. A sampling of the results will be shown. The third area is a status of the Turbine Performance Optimization task. The objective of this task is to improve the efficiency of a turbine for potential use on a next generation launch vehicle. This task includes global optimization for the preliminary design, detailed optimization for blade shapes and spacing, and application of advanced CFD analysis. The final design will be tested in the MSFC TTE.

Griffin, Lisa W.↗
NASA NTRS2010

Space Shuttle Main Engine Liquid Air Insulation Redesign Lessons Learned

The Space Shuttle Main Engine Liquid Air Insulation redesign was required to prevent the reoccurance of the STS-111 High Pressure Speed Sensor In-Flight Anomaly. The STS-111 In-Flight Anomaly Failure Investigation Team's initial redesign of the High Pressure Fuel Turbopump Pump End Ball Bearing Liquid Air Insulation failed the certification test by producing Liquid Air. The certification test failure indicated not only the High Pressure Fuel Turbopump Liquid Air Insulation, but all other Space Shuttle Main Engine Liquid Air Insulation. This paper will document the original Space Shuttle Main Engine Liquid Air STS-111 In-Flight Anomaly investigation, the heritage Space Shuttle Main Engine Insulation certification testing faults, the techniques and instrumentation used to accurately test the Liquid Air Insulation systems on the Stennis Space Center SSME test stand, the analysis techniques used to identify the Liquid Air Insulation problem areas and the analytical verification of the redesign before entering certification testing, Trade study down selected to three potential design solutions, the results of the development testing which down selected the final Liquid Air Redesign are also documented within this paper.

Darrell Gaddy↗
DOE OSTI2022

DEVELOPMENT OF OIL FREE CENTRIFUGAL BLOWER AS ENABLING TECHNOLOGY FOR SOLID OXIDE FUEL CELL ANODE GAS RECYCLING

Broad commercialization of solid oxide fuel cells (SOFCs), requires anode offgas recycle blowers (AORB) that are specifically designed for handling the challenging operating conditions presented by the SOFC process gases. Otherwise, they can be susceptible to frequent maintenance, low reliability, and short life. This work presents details of the development and testing of an oil-free, low cost centrifugal AORB based on compliant foil bearing (CFB) technology for support of a 100 kW solid oxide fuel cell power plant. The advantages of this novel technology are discussed, particularly its long life and maintenance-free operation, which are derived from the use of CFBs. Also included are preliminary techno-economic analysis considerations for cost-effective deployment of the technology.

03 NATURAL GAS↗