Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Mass transfer in fuel cells

Developments in the following areas are reported: surface area and pore size distribution in electrolyte matrices, electron microscopy of electrolyte matrices, surface tension of KOH solutions, water transport in fuel cells, and effectiveness factors for fuel cell components.

Walker, R. D., Jr.↗

Machine learning for optimizing the manufacture and operation of intermediate temperature fuel cells

The project developed machine learning and artificial intelligence (ML/AI) methodologies for guiding and accelerating the materials design and processing of new high temperature proton conducing electrode ionomer binders and reinforced membranes for high-temperature proton exchange membrane fuel cell (HT-PEMFC; aka intermediate-temperature polymer electrolyte membrane fuel cells).

08 HYDROGEN↗

Development of Ni1-xCoxO as the cathode/interconnect contact for solid oxide fuel cells

A new type of material, Ni1-xCoxO, was developed for solid oxide fuel cell (SOFC) cathode/interconnect contact applications. The phase structure, coefficient of thermal expansion, sintering behavior, electrical property, and mechanical bonding strength of these materials were evaluated against the requirements of the SOFC cathode/interconnect contact. A dense cathode/interconnect contact layer was developed through reaction sintering from Ni and Co metal powders. An area specific resistance (ASR) as low as 5.5 mohm.cm2 was observed after 1000 h exposure in air at 800 °C for the LSM/Ni0.33Co0.67O/AISI441 assembly. Average mechanical strengths of 6.8 and 5.0 MPa were obtained for the cathode/contact/cathode and interconnect/contact/interconnect structures, respectively. The significantly low ASR was probably due to the dense structure and therefore improved electrical conductivity of the Ni0.33Co0.67O contact and the good bonding of the interfaces between the contact and the cathode, and between the contact and the interconnect.

30 DIRECT ENERGY CONVERSION↗

Bottom up synthesis of boron-doped graphene for stable intermediate temperature fuel cell electrodes

The high surface area and electrical conductivity of few-layered graphene would make it an ideal catalyst support and electrode in fuel cells apart from its susceptibility to oxidative corrosion. Here we report the single-step, bottom-up synthesis of oxidation-resistant boron-doped graphene and show its increased stability in the aggressive electrochemical environment of intermediate temperature solid acid fuel cells (SAFCs). Boron was shown to alter the growth mode of single walled carbon nanohorns by laser vaporization to produce high yields of thin (<20 layer) boron-doped (2–3 at.%) crystalline flakes of turbostratic graphene (B-GLF). Alternatively, adding partial pressures of hydrogen less effectively shifted the growth mode of SWCNHs toward planar, turbostratic graphene-like flakes (GLFs). Thermogravimetric analysis indicates that boron-doping enhances the oxidation resistance of few-layer GLFs by >140 °C, with large fractions of multilayered B-GLFs surviving 10 °C/min ramps to 1000 °C. These B-GLFs provided a stable Pt catalyst support and electrode over 40 h operation in SAFCs with cesium dihydrogen phosphate electrolyte operating at 250 °C, as opposed to undoped GLFs or SWCNHs which were nearly completely consumed. Furthermore, the facile synthesis and oxidation-resistant properties of boron-doped GLF appear promising for graphene applications in oxidizing environments.

25 ENERGY STORAGE↗

Study of Hydrogen Fuel Cell Technology for Freight Rail Propulsion and Review of Relevant Industry Standards.

Alternatives to conventional diesel electric propulsion are currently of interest to rail operators. In the U.S., smaller railroads have implemented natural gas and other railroads are exploring hydrogen technology as a cleaner alternative to diesel. Diesel, battery, hydrogen fuel cell, or track electrification all have trade-offs for operations, economics, safety, and public acceptability. A framework to compare different technologies for specific applications is useful to optimize the desired results. Standards from the Association of American Railroads (AAR) and other industry best practices were reviewed for applicability with hydrogen fuel cell technology. Some technical gaps relate to the physical properties of hydrogen, such as embrittlement of metals, invisible flames, and low liquid temperatures. A reassessment of material selection, leak/flame detection, and thermal insulation methods is required. Hydrogen is less dense and diffuses more easily than natural gas, and liquid hydrogen is colder than liquefied natural gas. Different densities between natural gas and hydrogen require modifications to tank designs and flow rates. Leaked hydrogen will rise rather than pool on the ground like diesel, requiring a modification to the location of hydrogen tanks on rolling stock. Finally, the vibration and shock experienced in the rail environment is higher than light-duty vehicles and stationary applications for which current fuel cell technology has been developed, requiring a modification in tank design requirements and testing.

08 HYDROGEN↗

Fuel Cell Transit Bus Evaluations: Joint Evaluation Plan for the U.S. Department of Energy and the Federal Transit Administration (Report and Appendix)

This document describes the fuel cell transit bus evaluations performed by the National Renewable Energy Laboratory (NREL) and funded by the U.S. Department of Energy (DOE) and the U.S. Department of Transportation's Federal Transit Administration (FTA). This document provides a description of the demonstration sites, funding sources, and data collection activities for fuel cell transit busevaluations currently planned from FY10 through FY12.

08 HYDROGEN↗

A general approach to develop reduced order models for simulation of solid oxide fuel cell stacks

A reduced order modeling approach based on response surface techniques was developed for solid oxide fuel cell stacks. This approach creates a numerical model that can quickly compute desired performance variables of interest for a stack based on its input parameter set. The approach carefully samples the multidimensional design space based on the input parameter ranges, evaluates a detailed stack model at each of the sampled points, and performs regression for selected performance variables of interest to determine the responsive surfaces. After error analysis to ensure that sufficient accuracy is established for the response surfaces, they are then implemented in a calculator module for system-level studies. The benefit of this modeling approach is that it is sufficiently fast for integration with system modeling software and simulation of fuel cell-based power systems while still providing high fidelity information about the internal distributions of key variables. This paper describes the sampling, regression, sensitivity, error, and principal component analyses to identify the applicable methods for simulating a planar fuel cell stack.

Pan, Wenxiao↗

Ca{sub 3-x}La{sub x}Co{sub 4}O{sub 9+{delta}} (x=0, 0.3): New cobaltite materials as cathodes for proton conducting solid oxide fuel cell

Misfit-type Ca{sub 3-x}La{sub x}Co{sub 4}O{sub 9+{delta}} (x=0, 0.3) oxides were synthesised to be evaluated as possible cathode materials for proton conducting fuel cells (PCFCs) based on BaCe{sub 0.9}Y{sub 0.1}O{sub 3-{delta}} (BCY10) dense ceramic electrolyte. The electrical conductivity value of Ca{sub 2.7}La{sub 0.3}Co{sub 4}O{sub 9+{delta}} ({sigma}{approx}53 S cm{sup -1} at 600 deg. C) is in the range of usually required value for a cathode application (about 50-100 S cm{sup -1}). In order to test the performance of each compound as cathode material, impedance measurements were carried out on Ca{sub 3-x}La{sub x}Co{sub 4}O{sub 9+{delta}}/BaCe{sub 0.9}Y{sub 0.1}O{sub 3-{delta}}/Ca{sub 3-x}La{sub x}Co{sub 4}O{sub 9+{delta}} symmetrical half cells over the temperature range 400-800 deg. C under wet air. A promising electrocatalytic activity has been observed with both compounds Ca{sub 3}Co{sub 4}O{sub 9+{delta}} and Ca{sub 2.7}La{sub 0.3}Co{sub 4}O{sub 9+{delta}}. Factually, the area specific resistance obtained was about 2.2 {Omega} cm{sup 2} at 600 deg. C. - Graphical abstract: Arrehnius plots of the ASR for Ca{sub 3}Co{sub 4}O{sub 9+{delta}} and Ca{sub 2.7}La{sub 0.3}Co{sub 4}O{sub 9+{delta}}.

36 MATERIALS SCIENCE↗

Hydrogen fuel cell car race

Highlights from the Ames Lab's hydrogen fuel cell car race from the Middle School Science Bowl.

30 DIRECT ENERGY CONVERSION↗

Elucidating the Dynamic Nature of Fuel Cell Electrodes as a Function of Conditioning: An ex Situ Material Characterization and in Situ Electrochemical Diagnostic Study

To increase the commercialization of fuel cell electric vehicles, it is imperative to improve the activity and performance of electrocatalysts through combined efforts focused on material characterization and device-level integration. Obtaining fundamental insights into the ongoing structural and compositional changes of electrocatalysts is crucial for not only transitioning an electrode from its as-prepared to functional state, also known as 'conditioning', but also for establishing intrinsic electrochemical performances. Here, we investigated several oxygen reduction reaction (ORR) electrocatalysts via in situ and ex situ characterization techniques to provide fundamental insights into the interfacial phenomena that enable peak ORR mass activity and high current density performance. A mechanistic understanding of a fuel cell conditioning procedure is described, which encompasses voltage cycling and subsequent voltage recovery (VR) steps at low potential. In particular, ex situ membrane electrode assembly characterization using transmission electron microscopy and ultra-small angle X-ray scattering were performed to determine changes in carbon and Pt particle size and morphology, while in situ electrochemical diagnostics were performed either during or after specific points in the testing protocol to determine the electrochemical and interfacial changes occurring on the catalyst surface responsible for oxygen transport resistances through ionomer films. The results demonstrate that the voltage cycling (break-in) step aids in the removal of sulfate and fluoride and concomitantly reduces non-Fickian oxygen transport resistances, especially for catalysts where Pt is located within the pores of the carbon support. Subsequent low voltage holds at low temperature and oversaturated conditions, i.e., VR cycles, serve to improve mass activities by a factor of two to three, through a combined removal of contaminants, surface-blocking species (e.g., oxides), and rearrangement of the catalyst atomic structure (e.g., Pt-Pt and Pt-Co coordination).

30 DIRECT ENERGY CONVERSION↗

Iron Single Atoms on Graphene as Nonprecious Metal Catalysts for High‐Temperature Polymer Electrolyte Membrane Fuel Cells

Abstract Iron single atom catalysts (Fe SACs) are the best‐known nonprecious metal (NPM) catalysts for the oxygen reduction reaction (ORR) of polymer electrolyte membrane fuel cells (PEMFCs), but their practical application has been constrained by the low Fe SACs loading (<2 wt%). Here, a one‐pot pyrolysis method is reported for the synthesis of iron single atoms on graphene (FeSA‐G) with a high Fe SAC loading of ≈7.7 ± 1.3 wt%. The as‐synthesized FeSA‐G shows an onset potential of 0.950 V and a half‐wave potential of 0.804 V in acid electrolyte for the ORR, similar to that of Pt/C catalysts but with a much higher stability and higher phosphate anion tolerance. High temperature SiO 2 nanoparticle‐doped phosphoric acid/polybenzimidazole (PA/PBI/SiO 2 ) composite membrane cells utilizing a FeSA‐G cathode with Fe SAC loading of 0.3 mg cm −2 delivers a peak power density of 325 mW cm −2 at 230 °C, better than 313 mW cm −2 obtained on the cell with a Pt/C cathode at a Pt loading of 1 mg cm −2 . The cell with FeSA‐G cathode exhibits superior stability at 230 °C, as compared to that with Pt/C cathode. Our results provide a new approach to developing practical NPM catalysts to replace Pt‐based catalysts for fuel cells.

25 ENERGY STORAGE↗