Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLEXURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Nondestructive evaluation of a ceramic matrix composite material

Monolithic ceramic materials have proven their usefulness in many applications, yet, their potential for critical structural applications is limited because of their sensitivity to small imperfections. To overcome this extreme sensitivity to small imperfections, ceramic matrix composite materials have been developed that have the ability to withstand some distributed damage. A borosilicate glass reinforced with several layers of silicon-carbide fiber mat has been studied. Four-point flexure and tension tests were performed not only to determine some of the material properties, but also to initiate a controlled amount of damage within each specimen. Acousto-ultrasonic (AU) measurements were performed periodically during mechanical testing. This paper will compare the AU results to the mechanical test results and data from other nondestructive methods including acoustic emission monitoring and X-ray radiography. It was found that the AU measurements were sensitive to the damage that had developed within the material.

Grosskopf, Paul P.↗

Nonlinear response of graphite-epoxy wide columns subject to eccentric load

It is shown that including the effects of bend-twist coupling and material nonlinearity on the large displacement flexural response of graphite-epoxy wide columns is necessary to adequately model their response. Results from static tests on 0(30)T and (30/0/-30 sub 5)s laminated specimens under eccentric axial compression are compared to a nonlinear analysis. The analysis is based on a Kantrovich expansion of the displacements in the width coordinate and a finite element representation in the axial coordinate. An incremental, updated Lagrangian formulation and element corotational coordinates are employed. Nonlinear elastic material behavior was measured in a separate set of material characterization tests, and these data are used to compute tangent stillnesses in the updated configuration.

Griffin, O. H., Jr.↗

A flutter investigation of all-moveable NASP-like wings at hypersonic speeds

Six alternative all-moving wing configurations applicable to the NASP hypersonic/transatmospheric vehicle have undergone aeroelasticity testing in NASA-Langley's Mach-20-capable Helium Tunnel that yielded data for such parametric variations as airfoil profile and wing planform, wing-pivot flexure stiffness, and mass imbalance. While all wings fluttered at dynamic pressures lower than predicted by second-order piston-theory aerodynamics, this was of limited amplitude, suggesting nonlinear external-flow behavior. Slab airfoils were more stable than diamond-shaped ones; blunt leading edges enhance stability relative to sharp ones, and stiffer pivolts extert a stabilizing influence.

Spain, Charles V.↗

Radii effect on the translation spring constant of force transducer beams

Multi-component strain-gage force transducer design requires the designer to determine the spring constant of the numerous beams or flexures incorporated in the transducer. The classical beam deflection formulae that are used in calculating these spring constants typically assume that the beam has a uniform moment of inertia along the entire beam length. In practice all beams have a radius at the end where the beam interfaces with the shoulder of the transducer, and on short beams in particular this increases the beam spring constant considerably. A Basic computer program utilizing numerical integration is presented to determine this effect.

Scott, C. E.↗

Prototype high speed optical delay line for stellar interferometry

The long baselines of the next-generation ground-based optical stellar interferometers require optical delay lines which can maintain nm-level path-length accuracy while moving at high speeds. NASA-JPL is currently designing delay lines to meet these requirements. The design is an enhanced version of the Mark III delay line, with the following key features: hardened, large diameter wheels, rather than recirculating ball bearings, to reduce mechanical noise; a friction-drive cart which bears the cable-dragging forces, and drives the optics cart through a force connection only; a balanced PZT assembly to enable high-bandwidth path-length control; and a precision aligned flexural suspension for the optics assembly to minimize bearing noise feedthrough. The delay line is fully programmable in position and velocity, and the system is controlled with four cascaded software feedback loops. Preliminary performance is a jitter in any 5 ms window of less than 10 nm rms for delay rates of up to 28 mm/s; total jitter is less than 10 nm rms for delay rates up to 20 mm/s.

Colavita, M. M.↗

Brush seal low surface speed hard-rub characteristics

The bristles of a 38.1-mm (1.5-in.) diameter brush seal were flexed by a tapered, 40-tooth rotor operating at 2600 rpm that provided sharp leading-edge impact of the bristles with hard rubbing of the rotor lands. Three separate tests were run with the same brush accumulating over 1.3 x 10(exp 9) flexure cycles while deteriorating 0.2 mm (0.008 in.) radially. In each, the test bristle incursion depth varied from 0.130 to 0.025 mm (0.005 to 0.001 in.) or less (start to stop), and in the third test the rotor was set 0.25 mm (0.010 in.) eccentric. Runout varied from 0.025 to 0.076 mm (0.001 to 0.003 in.) radially. The bristles wore but did not pull out, fracture, or fragment. Bristle and rotor wear debris were deposited as very fine, nearly amorphous, highly porous materials at the rotor groove leading edges and within the rotor grooves. The land leading edges showed irregular wear and the beginning of a convergent groove that exhibited sharp, detailed wear at the land trailing edges. Surface grooving, burnishing, 'whipping,' and hot spots and streaks were found. With a smooth-plug rotor, post-test leakage increased 30 percent over pretest leakage.

Hendricks, Robert C.↗

Effect of mission cycling on the fatigue performance of SiC-coated carbon-carbon composites

The effects of thermal and pressure cycling on the fatigue performance of carbon-carbon composites, and the influence of mission cycling on these effects, were investigated by subjecting both virgin and mission-cycled two-dimensional specimens of SiC-coated carbon-carbon composites to fatigue tests, conducted at room temperature in three-point bending, with a stress ratio of 0.2 and a frequency of 1 Hz. It was found that the fatigue strength of C-C composites is high (about 90 percent of the ultimate flexural strength), but decreased with the mission cycling. The lowering of the fatigue strength with mission cycling is attributed to the increase in interfacial bond strength due to thermal and pressure cycling of the material. The already high sensitivity of C-C composites to stress during cyclic loading increases further with the amount of mission cycling. Results of NDE suggest that the damage growth in virgin C-C, in the high-cycle range, is slow at the initial stage of the cyclic life, but propagates rapidly after certain threshold cycles of the fatigue life.

Mahfuz, H.↗

Properties of powder-impregnated graphite/PEKK

Poly Ether Ketone Ketone (PEKK) powders were prepregged on AS4 (12K), IM7 (12K), and G30-500 (12K) carbon fibers and consolidated into unidirectional laminates. The preferred formulation of PEKK for the dry powder process was identified. Mechanical test data on panels prepared via the powder process agreed well with flex, short beam shear, and double cantilever beam values obtained previously on melt-impregnated material. IM7/PEKK composites showed superior mechanical properties to AS4/PEKK and G30-500/PEKK composites. Transverse flexural strength and fiber/resin contact angle correlated well as measures of the fiber/matrix interfacial strength.

Bucher, R. A.↗

Remarks on the elastic axis of shell wings

The definitions of flexural center, torsional center, elastic center, and elastic axis are discussed. The calculation of elastic centers is dealt with in principle and a suggestion is made for the design of shear webs.

Kuhn, Paul↗

Transonic-flutter Investigation of Wings Attached to Two Low-acceleration Rocket-propelled Vehicles

Two low-acceleration transonic-flutter vehicles were launched and flown. The first carried two test wings, one of which fluttered at M = 0.92 at a frequency of 61.4 cycles per second. The reference flutter speed determined from two-dimensional theory for an unswept wing in incompressible flow is conservative when compared to the experimental flutter speed. The second vehicle carried two test wings, one of which failed at M = 0.71 because of low-frequency divergent oscillation. Since this failure was not caused by conventional flexure-torsion flutter, no comparison with a reference flutter speed can be made.

MISSILES, SPECIFIC TYPES↗

Beam and Torsion Tests of Aluminum-alloy 61S-T Tubing

Tests were made to determine the effect of length and the effect of ratios of diameter to wall thickness upon the flexural and torsional moduli of failure of 61S-T aluminum-alloy tubing. The moduli of failure in bending, as determined by tests in which the tubing was loaded on the neutral axis at the one-third points of the span, were found to bear an approximately linear relationship with diameter-thickness ratio and were practically independent of span within the limits investigated. Empirical equations are given describing the relations obtained. The moduli of failure in torsion were found to be dependent upon length as well as upon diameter-thickness ratios. Empirical equations are given for predicting strengths within the range of plastic buckling. Within the elastic range, available torsion theories were found to be satisfactory.

Moore, R L↗

A Study of Wing Flutter

Part I describes vibration tests, in a wind tunnel, of simple airfoils and of the tail plane of an M0-1 airplane model; it also describes the air flow about this model. From these tests are drawn inferences as to the cause and cure of aerodynamic wing vibrations. Part II derives stability criteria for wing vibrations in pitch and roll, and gives design rules to obviate instability. Part III shows how to design spars to flex equally under a given wing loading and thereby economically minimize the twisting in pitch that permits cumulative flutter. Resonant flutter is not likely to ensue from turbulence of air flow along past wings and tail planes in usual flying conditions. To be flutterproof a wing must be void of reversible autorotation and not have its centroid far aft of its pitching axis, i. e., axis of pitching motion. Danger of flutter is minimized by so proportioning the wing's torsional resisting moment to the air pitching moment at high-speed angles that the torsional flexure is always small. (author)

Zahm, A F↗

Determination of the bending and buckling effect in the stress analysis of shell structures accessible from one side only

The present report describes a device for ascertaining the bending and buckling effect in stress measurements on shell structures accessible from one side only. Beginning with a discussion of the relationship between flexural strain and certain parameters, the respective errors of the test method for great or variable skin curvature within the test range are analyzed and illustrated by specimen example.

Dose, A↗

The Mechanical Properties of Wood of Different Moisture Content Within -200 Degrees to +200 Degrees C Temperature Range

Systematic experiments were undertaken with special reference to the effect of gross specific weight (specific weight inclusive of pores) and the moisture content of wood. It was found that the modules of elasticity of wood at room temperature and frozen at -8 degrees is practically the same. The effect of moisture on the compression strength of frozen wood was explored as well as the flexural and impact strength of frozen wood and frozen laminated wood.

Kollmann, Franz↗

The Effective Width of Curved Sheet After Buckling

This report describes experiments made for the purpose of ascertaining the effective width of circularly curved sheet under pure flexural stress. A relation for the effective width of curved sheets is established. Experiments were made with circular cylinders compressed in longitudinal direction. The sheets were rigidly built in at the sides parallel to the axis of the cylinder.

Wenzek, W A↗

Torsion and buckling of open sections

Following an abstract of the well-known theory of torsion in compression, the writers give directions for the practical calculation of the values of C(sub BT) (resistance to flexure and torsion) and i(sub SP(exp 2)), which determine the torsion. The second part treats the experiments in support of the theory of torsion of plain and flanged angle sections.

Wagner, H↗

Contribution to the theory of propeller vibrations

This report presents a calculation of the torsional frequencies of revolving bars with allowance for the air forces. Calculation of the flexural or bonding frequencies of revolving straight or tapered bars in terms of the angular velocity of revolution. Calculation on the basis of Rayleigh's principle of variation. There is also a discussion of error estimation and the accuracy of results. The author then provides an application of the theory to screw propellers for airplanes and the discusses the liability of propellers to damage through vibrations due to lack of uniform loading.

Liebers, F↗

Test Bed For Control Of Optical-Path Lengths

Truss structure and ancillary equipment constitute test bed for experiments in methods of controlling lengths of optical paths under conditions of structural vibration and deformation. Accommodates both passive and active methods of control. Experimental control system reduces millimeter-level disturbances in optical path length to nanometers. Developed for control, alignment, and aiming of distributed optical systems on large flexible structures. Test bed includes tower 2.5 meters high with two horizontal arms extending at right angles from its top. Rigidly mounted on massive steel block providing measure of isolation from ground vibrations. Optical motion-compensation system similar to one described previously in NASA Tech Briefs enclosed in flexure-mounted frame, called "trolley," at end of longer horizontal arm.

O'Neal, Michael C.↗