Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELONGATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

The Effect of SiC Addition on Microstructure and Mechanical Properties of Gas Tungsten Arc-Welded Ti-6Al-4V Alloy

In the present study, SiC powder was added in situ for bead-on-plate weldments and fusion butt joints to modify the microstructure and the corresponding mechanical properties. Cross sections of bead-on-plate welds demonstrated that the SiC addition resulted in significant changes of the titanium microstructure. Specifically, a fine lamellar structure of α-phase with a small amount of intergranular β-titanium within the fusion zone could be established. Moreover, the size of prior β-grains was significantly reduced. After welding, no intermetallic silicides were observed. In the fusion zone of the SiC-enhanced samples, a small increase in hardness resulted, and the samples showed an increase in tensile strength, yield strength and elongation.

36 MATERIALS SCIENCE↗

Control of Carbon Content in Steel by Introducing Proeutectoid Ferrite Transformation into Hot-Rolled Q&P Process

A processing strategy involving primary and secondary carbon partitioning is proposed for the hot-rolled quenching and partitioning process through the introduction of proeutectoid ferrite transformation after rolling. The microstructures of the steels were characterized using scanning electron microscopy, transmission electron microscopy, electron probe microanalysis, and x-ray diffraction, and the mechanical properties were evaluated using a universal tensile machine. The blocky retained austenite that distributed along the ferrite grain boundaries was promoted based on the coupling action of the primary and secondary carbon partitioning, which enhanced the transformation-induced plasticity effect during deformation despite the high carbon concentration. A ferrite formation temperature range of ~ 760 to 800 °C was proposed. In addition, from the perspective of industrialization, the observed ‘plateau trends’ for the retained austenite fraction and product of strength and elongation suggest the availability of a wide processing window of 215-362 °C for controlling the coiling temperature.

36 MATERIALS SCIENCE↗

Microstructure Characteristic and Mechanical Properties of High-Strength Mg-Nd-Zn-Zr Alloy Seamless Tube Produced by Integrated Extrusion

Large size seamless tubes of Mg-3.0Nd-0.4Zn-0.4Zr alloy (NZ30K, in weight percent) were prepared by integrating backward extrusion with forward extrusion. Microstructure, mechanical properties, aging behavior and texture of the tubes were investigated. The microstructure of as-extruded tube is characterized by the blend of considerably elongated grains and fine equiaxed grains. The maximum values of yield strength and ultimate tensile strength, i.e., 191 and 245 MPa, were obtained in the as-extruded tubes, and these values were increased to 212 and 267 MPa in the peak-aged tubes (T5), implying an increasing ratio of 9 and 11%, respectively. The peak value of the Vickers’ micro-hardness of the NZ30K tubes extruded at 673, 723 and 753 K are 66, 64 and 60 (kilogram-force per square millimeter), respectively. The texture of NZ30K tube is weak, the primary mechanism behind which is suggested to be the particle-induced nucleation responsible for the promotion of recrystallization.

36 MATERIALS SCIENCE↗

Microstructure of Friction Stir Welded AlSi9Mg Cast with 5083 and 2017A Wrought Aluminum Alloys

Wrought aluminum alloys 5083 and 2017A were each joined with cast aluminum alloy AlSi9Mg through friction stir welding in butt weld configurations. For each material system, the wrought and cast alloy positions, i.e., the advancing side or the retreating side, were exchanged between welding trials. The produced weldments were free from cracks and discontinuities. For each alloy configuration, a well-defined nugget comprised of alternating bands of the welded alloys characterized the microstructure. The degree of mixing, however, strongly depended on which wrought alloy was present and on its position during processing. In all cases, the cast AlSi9Mg alloy dominated the weld center regardless of its position during welding. Electron backscattered diffraction analysis showed that the grain size in both alloys (bands) constituting the nugget was similar and that the majority of grain boundaries exhibited a high angle character (20°-60°). Regardless of the alloy, however, all grains were elongated along the direction of the material plastic flow during welding. A numerical simulation of the joining process visualized the material flow patterns and temperature distribution and helped to rationalize the microstructural observations. The hardness profiles across the weld reflected the microstructure formed during welding and correlated well with the temperature changes predicted by the numerical model. Tensile specimens consistently fractured in the cast alloy near the weld nugget.

36 MATERIALS SCIENCE↗

Cu-7Cr-0.1Ag Microcomposites Optimized for High Strength and High Condutivity

This paper (i) investigated how the microstructure, conductivity, and mechanical properties of Cu-7Cr-0.1Ag microcomposites were changed by cold drawing and subsequent heat treatment, and (ii) produced the Cu-7Cr-0.1Ag microcomposite with an optimum combination of strength and conductivity. The figure of merit Z (combining strength and conductivity) of the Cu-7Cr-0.1Ag microcomposite was larger than that of the microcomposite without silver for each heat treatment. The value of Z of the Cu-7Cr-0.1Ag microcomposite was a maximum after heat treatment for 1 h at 600 °C, indicating that this was the optimum intermediate heat treatment. The following combinations of conductivity, strength and ductility (measured as elongation to fracture) were obtained by the Cu-7Cr-0.1Ag microcomposite with η = 8: (i) 77.9% IACS (International Annealed Copper Standard), 920 MPa and 3.1%; (ii) 79.3% IACS, 880 MPa and 3.3%; and (iii) 79.9% IACS, 798 MPa and 3.5%. These values for the Cu-7Cr-0.1Ag microcomposite were larger than those of the Cu-7Cr microcomposite.

36 MATERIALS SCIENCE↗

Alleviation of Mechanical Anisotropy in Ultrafine/Nano-grained AZ31 Magnesium Alloy

An ultrafine/nano-grained AZ31 magnesium alloy was processed through multipass accumulative back extrusion at 280 and 380 °C. Texture analysis was conducted to determine preferred crystallographic orientations developed during multipass deformation. The anisotropy in mechanical properties of the processed materials was studied by compressive and tensile testing. The results implied that the accumulative back extrusion effectively reduces the anisotropy of yield strength, ultimate strength and strain-to-fracture during compressive and tensile loading. The operations of different twinning/slip systems during compressive and tensile deformation were discussed using Schmid factors measurements. A decrease in twinning-related anisotropy, as well as the contribution of different slip systems in strain accommodation, could reduce the mechanical anisotropy of ultrafine/nano-grained AZ31 alloy. The compressive strength of the two-pass processed material was lower along extrusion direction than transverse direction; however, the result was reverse after four passes. The tensile behavior implied that the contribution of basal slip might accommodate strain along length as well as the thickness of the specimen, while prismatic slip may assist in narrowing the width of the specimen and elongating the length.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of Rapidly Cooled Friction Stir Welded Ti-6Al-4V Alloys

Two mm-thick Ti-6Al-4V alloy plates were friction stir butt welded under natural- and rapid-cooling conditions. The microstructures and mechanical properties of joints were investigated and compared. The rapid cooling via spraying cooling liquid nitrogen on the plate top surface was beneficial to obtaining a narrower cross section and finer and more uniform grains in the stir zone than those obtained by natural cooling. Joint tensile strength of 1021 MPa and elongation of 1.88% under the rapid-cooling condition respectively reached 102.7 and 150.4% of those under the natural-cooling condition, respectively. The uniform-and-compact equiaxed grains led to equiaxed dimples on the fracture surface, which demonstrated a ductile fracture of the welding joints.

36 MATERIALS SCIENCE↗

Microstructural Characterization, Mechanical Properties, and Corrosion Resistance of Dental Co-Cr-Mo-W Alloys Manufactured by Selective Laser Melting

In this paper, the microstructure, mechanical properties, and corrosion resistance of the dental Co-Cr-Mo-W alloys fabricated by selective laser melting (SLM) were systematically investigated and correlated. The microstructure of the SLM group (SG) specimens is composed of extremely fine columnar crystals, exhibiting supersaturated and homogeneous character. The matrix mainly consists of face-centered-cubic (FCC) cobalt solid solutions, and minimal hexagonal-close-packed (HCP) cobalt solid solutions. Mechanical test results showed that the 0.2% yield strength of SG was 775 ± 7 MPa, and the ultimate tensile strength was 1118 ± 25 MPa. The elongation of SG was 8.28 ± 0.4%, and the microhardness of SG was 476 ± 10 HV. All of these values largely exceeded the cast group (CG) specimens. The high strength is attributed to their fine columnar crystals and supersaturated matrices. The fewer content from the HCP phase and a lack of intermetallic compounds or eutectic contribute to the high ductility. Furthermore, a higher E{sub corr}, lower I{sub corr} were acquired for better corrosion resistance compared to cast specimens, due to even less composition segregation and more microstructural homogeneity.

36 MATERIALS SCIENCE↗

Microstructure, Texture, and Mechanical Properties of Ni-W Alloy After Accumulative Roll Bonding

In this study, the microstructure, texture, and mechanical properties evolution of Ni-14W (wt.%) alloy processed up to four cycles of accumulative roll-bonding (ARB) were investigated using electron backscatter diffraction, microhardness measurements, and tensile tests. The initial equiaxed grains, with an average size of 10 μm, underwent a strong refinement after ARB processing. The elongated ultrafine grains were parallel to the rolling direction, with a grain thickness of 0.2 µm. The texture after ARB processing was characterized by the typical rolling components (Copper, S and Brass), which showed a tendency toward stabilization after four cycles. The microhardness increased substantially (+ 86%) and seemed to saturate after three cycles. The tensile tests demonstrated that Ni-14W samples subjected to ARB processing exhibited high strength (> 1200 MPa after three ARB cycles) and very poor ductility.

36 MATERIALS SCIENCE↗

Study on Texture Evolution and Shear Behavior of an Al/Ni/Cu Composite

The microstructure, texture, and mechanical properties of the Al/Ni/Cu composite during various accumulative roll bonding (ARB) cycles were studied using optical microscopy, scanning electron microscopy, x-ray diffraction, shear punch test, and hardness test. In addition, ImageJ software and Rietveld software were used in order to study microstructure and dislocation density variations, respectively. It was found that Ni and Cu layers were fractured and distributed in the Al matrix due to differences in their mechanical properties. Fracture and distribution of Cu and Ni particles after cycle five led to the alteration of the composite structure from a layered to a particle-reinforced structure. ARB process leads to the formation of strong orientation along the β-fiber and also to pronounced copper and dillamore components in both Al and Cu phases. Furthermore, the shear yield stress and ultimate shear strength of the composite increased as the ARB process advanced; however, shear elongation presented a non-uniform variation. Investigation of the fracture surfaces revealed that the mechanical properties of the composite are affected not only by the strain hardening of the Cu layer, but also by the structural change in the composite during the initial ARB cycles. During the last stages of the process, however, changes in mechanical properties were mostly governed by reinforcement particles serving as strain concentration zones and the strain hardening of the Al matrix.

36 MATERIALS SCIENCE↗

Formability, Microstructure and Mechanical Properties of Flow-Formed 17-4 PH Stainless Steel

The subject of the research that has been conducted in this paper was to analyze precipitation-hardened martensitic stainless steel 17-4 PH after flow forming with four different strains and subsequent standard heat treatment. Four cylinders were obtained with a 16, 30, 48 and 68% reduction in thickness, respectively. The samples were analyzed in terms of their mechanical properties and microstructural changes before and after the heat treatment. The results showed that a higher strain resulted in an overall higher strength (up to 1200 MPa UTS) and refinement of the structure, although at a cost of the elongation. High deformation influenced the precipitation process, and the ratio of the grain boundaries significantly increased. Nonetheless, comparing the obtained results with other similar research, it seems that the formation of nano-precipitates of Cu is the key-strengthening mechanism. Strain hardening contributes to an increase in the strength of the steel, although the effect decreases after heat treatment. The relatively small values of residual stress in the steel, especially after the heat treatment, confirmed these claims. Overall, flow forming allowed high deformations of the 17-4 PH steel to be obtained although it did not significantly change the mechanical properties of the material due to the dominant precipitation hardening mechanism.

36 MATERIALS SCIENCE↗

Wear-Resistant Al/SiC-Gr Hybrid Metal Matrix Composite Fabricated by Multiple Annealing and Roll Bonding

The wear-resistant Al/SiC-Gr hybrid composite with a good combination of strength and ductility is fabricated by multiple annealing and roll bonding. The challenge is that graphite acts as a soft lubricating material and prevents the bonding between the layers. In order to evaluate the bond strength, the peeling test is used after cold roll bonding of Al strips with and without the addition of particles under different conditions. Results show that the bond strength increases with increasing the reduction in thickness, decreasing Gr content and performing the post-rolling annealing. During the multiple annealing and roll bonding process, the tensile strength increases with the cost of a small decrease in elongation. A relatively uniform distribution of particles is achieved at the last stages of the process. The Al/SiC-Gr hybrid composite exhibits an improved wear resistance compared with the monolithic Al and Al/SiC composite produced under the same conditions. The conclusion is drawn that a good combination of wear and mechanical properties can be achieved in the hybrid composite that has less amount of Gr.

36 MATERIALS SCIENCE↗

Correlation Between Structure and Properties of Low-Carbon Cu-Ni-Mo-Ti-Nb Ultrahigh-Strength Steel

Low-carbon Cu-Ni-Mo-Ti-Nb steel having more than 1700 MPa tensile strength and good low-temperature impact toughness was successfully designed and processed for automobile, defence and structural applications. The steel was thermomechanical controlled processed at a different finish rolling temperatures (750-850 °C) and cooled at two different conditions: air cooling and water quenching. Evolutions of microstructure and precipitates were thoroughly characterised to understand the effect of different factors, such as steel composition, finish rolling temperature and cooling rate on the mechanical properties. The results indicate that the steel processed at 750 °C finish rolling temperature (FRT) followed by water quenching has exhibited superior tensile properties with a yield strength of 1034-1449 MPa, the tensile strength of 1598-1726 MPa and total elongation of 10-13%. Such an ultrahigh-strength level is primarily attributed to the combined effect of lower bainite dominated microstructure along with precipitation hardening. The satisfactory low-temperature toughness is promoted by low finish rolling temperature and higher amount of misorientation offered by the boundaries within the lower bainite.

36 MATERIALS SCIENCE↗

Micromechanical Modeling and Investigating the Effect of Particle Size and the Interface of Phases on the Mechanical Behavior of Dual-Phase Steels

Dual-phase (DP) ferrite–martensite steels have a fine microstructure that consist of martensite islands, dispersed in a ferrite matrix. In the present work, a micromechanical-based finite element (FE) analysis is carried out in order to investigate the mechanical properties of this type of steels, such as yield stress and tensile strength. The step forward contribution of the present study is to insert the effect of the presence of the interface of the constituting phases in the FE model. In order to do so, a micromechanical FE model is developed in which the effect of the interface of the constituting phases is taken into account by means of cohesive elements. The required parameters of the cohesive elements are determined by a trial and error procedure which compares the numerical results to the experimental ones. Experimental data is used to verify the created FE model. This model is then used to investigate the effect of martensite volume fraction and small-to-large particle size ratio of martensite on the deformation behavior of the DP steel. This study shows that considering the interface of the constituting phases greatly affects the numerical results on stress and strain distributions and produces more realistic findings in agreement with experiments. The results show that applying cohesive elements between two phases have reduced tensile strength, yield stress, and the amount of uniform elongation.

36 MATERIALS SCIENCE↗

Effects of Heat Treatment on Microstructure, Mechanical Properties, Corrosion Resistance and Cytotoxicity of ZM21 Magnesium Alloy as Biomaterials

The effects of heat treatment on microstructure, mechanical properties, corrosion resistance and cytotoxicity of extruded Mg-2Zn-1Mn (wt.%) alloy were investigated for biomedical application in this study. The extruded alloy was T4 treated at 510 °C for 4 h and T5 treated at 200 °C for 16 h separately. The extruded Mg-Zn-Mn alloy mainly consists of Mg{sub x}Mn{sub y} phases. After T4 treatment, the amount of Mg{sub x}Mn{sub y} phases decreases and average grain size rises from 8 to 24 μm. After T5 treatment, Mg{sub 7}Zn{sub 3} phase newly precipitates along the grain boundaries and the size of grain remains similar. Compared with the T4-treated samples, the extruded and T5-treated samples exhibit higher mechanical properties. The T5-treated samples have an ultimate tensile stress of 273 MPa and an elongation of 19.7%. On the other hand, T4-treated samples present higher corrosion resistance in electrochemical tests. The degradation rates of extruded, T4-treated and T5-treated samples are 0.44 mm/year, 0.48 mm/year and 0.50 mm/year, respectively, in Ringer’s solution at 37 ± 0.2 °C. In addition, T4-treated alloy does not induce toxicity to the L-929 cells in in vitro cytotoxicity test.

36 MATERIALS SCIENCE↗

Surface Self-nanocrystallization in Copper Electroforming

The coarse columnar grain layer generated on top of electroforming deposits leads to low surface strength and poor global performance of deposits. Here, we introduce a particle abrasive-induced surface self-nanocrystallization process, which is a part of the electroforming process rather than involving complex poststeps using special equipment. It can generate a thickness-controllable surface nanocrystalline layer on top of copper deposits for performance enhancement. In this study, surface nanocrystalline layers of 10, 20, 50 and 120 μm were fabricated on top of 500-μm-thick copper deposits. The tensile strength of copper deposits increases from 234 to 246, 330, 383 and 421 MPa, with a corresponding decrease in elongation from 26 to 25, 24, 15 and 6%, respectively. The moderately thick surface nanocrystalline layer makes the copper deposits exhibit good comprehensive mechanical properties. In addition, the surface self-nanocrystallization also makes the copper deposits show a better corrosion resistance in a neutral aqueous 0.1 M NaCl solution. This study aims to promote a convenient, controllable and reliable surface self-nanocrystallization process in electroforming for improving the global performance of deposits.

36 MATERIALS SCIENCE↗

Design and Development of Galvannealed Dual-Phase Steel: Microstructure, Mechanical Properties and Weldability

It was attempted to produce galvannealed dual-phase (DP) steel through a commercial continuous galvanizing line (CGL). The main challenge was to form the DP microstructure even with the slow cooling rate after annealing in the CGL. A two-pronged approach was adopted for this, viz. design of the steel chemistry with calculations and optimization of the CGL parameters with simulation using Gleeble-3800 thermomechanical simulator. The steel thus produced in CGL revealed ferrite and 18 ± 2% martensite microstructure, with tensile strength exceeding 600 MPa and 24% total elongation along with good formability. Weldability study using resistance spot welding indicated the possibility of achieving sound joint with a 4-kA width in weld time–current lobe despite the high carbon equivalence.

36 MATERIALS SCIENCE↗

EBSD Study on Processing Domain Parameters of Oxide Dispersion Strengthened 18Cr Ferritic Steel

This paper presents the results of an experimental study aimed to identify hot working domains in oxide dispersion strengthened (ODS) 18Cr ferritic steel over a wide range of temperatures (1323-1473 K) and strain rates (0.01-10 s{sup −1}). The experimental data were obtained by uniaxial compression test using the Gleeble-1500D simulator in this range of temperature and strain rate. An inverse relationship with temperature and positive strain rate sensitivity associated with dynamic recovery and recrystallization, which is influenced by temperature and strain rate, was derived from the flow stress. Based on the processing map generated at 0.5 true strain, using rate dynamic material model (DMM) approach and the calculated instability parameter (ξ(ϵ́))>0, the optimum processing domain has been determined for this steel. The most favorable processing parameters are found in the temperature ranges of 1350-1450 K with a strain rate of 0.01 s{sup −1} and 1473 K with a strain rate 0.1 s{sup −1} with peak efficiency of 30 and 35%, respectively. The material flow behavior was studied using scanning electron microscopy (SEM)-based EBSD microstructural characterization. The steel subjected to 1323 K at high strain rate 10 s{sup −1} in the low-efficiency workability region showed low aspect ratio as compared to the elongated bamboo-like initial microstructure; however, minimum strain rate (0.01 s{sup −1}) showing that localized slip/shearing is the key mechanism and fiber texture studied from the intensity distribution of inverse pole figure showed the presence of significant amount of θ-fibers. In contrast, dynamic recrystallization dominated at higher efficiency region in the safe domain of processing map and γ-fiber texture was evident in the specimen deformed at 1373 and 1473 K with strain rate of 0.01 and 0.1 s{sup −1}, respectively, which is responsible for the change in the initial 〈1 1 0〉//ED α-fiber texture.

36 MATERIALS SCIENCE↗